Pelco CRT Television PMM12A User Manual

I N S T A L L A T I O N / O P E R A T I O N  
PMM9A, PMM12A,  
PMM15A, PMM20A  
Monochrome Monitors  
®
C2902M (10/02)  
 
LIST OF ILLUSTRATIONS  
Figure  
Page  
1
2
3
4
5
Singe-Monitor Installation (PMM15A Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Multiple-Monitor Installation (PMM15A Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Location of Controls (PMM15A Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Vertical Roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Horizontal Tear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
LIST OF TABLES  
Table  
Page  
Video Coaxial Cable Wiring Distances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
A
C2902M (10/02)  
3
 
IMPORTANT SAFEGUARDS AND WARNINGS  
Before installing your equipment, please read the following important safeguards as outlined by Underwriters Laboratories Inc.  
Read Instructions  
All the safety and operating instructions should be read before the appliance is operated.  
Retain Instructions  
The safety and operating instructions should be retained for future reference.  
Heed Warnings  
All warnings on the appliance and in the operating instructions should be followed.  
Follow Instructions  
All operating and use instructions should be followed.  
Cleaning  
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.  
Attachments  
Do not use attachments not recommended by Pelco as they may cause hazards.  
Water and Moisture  
Do not use this CCTV product near water–for example, near a kitchen sink, wash bowl, bath tub, sprinkler, in a wet basement or  
near a swimming pool, and the like unless it is specifically marked “for use in wet locations.”  
Accessories  
Do not place this CCTV product on an unstable cart, stand, tripod, bracket, or table. The CCTV product may fall, causing serious  
injury to a child or adult and serious damage to the appliance. Use only with a cart, stand, tripod, bracket or table recom-  
mended by Pelco or supplied by Pelco with the product. When mounting the appliance, follow Pelcos installation instructions,  
and use only mounting accessories recommended by Pelco.  
Cart & Stand  
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause  
the appliance and cart combination to overturn.  
Ventilation  
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the CCTV product and to  
protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing  
the CCTV product on furniture, carpet, or similar surfaces. The CCTV product should never be placed near or over radiators or  
heat registers. This CCTV product should not be placed in a built-in installation, such as a book case or rack, unless proper  
ventilation is provided or Pelco’s installation instructions are adhered to.  
Power Sources  
This CCTV product should only be operated from the type of power source indicated on the marketing label. If you are not sure  
of the type of power supply to your installation location, consult your local electrical building official or power company. Refer  
to the operating instructions for appliances intended to operate from battery or other power sources.  
Grounding  
This CCTV product is equipped with a grounding-type plug. This plug will only fit into a grounding-type power outlet. This is a  
safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do  
not defeat the grounding-type plug since it is provided to ensure your safety.  
Power-Cord Protection  
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against  
them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.  
Overloading  
Do no overload wall outlets and extension cords as this can result in a risk of fire or electric shock.  
4
C2902M (10/02)  
 
Object and Liquid Entry  
Never push objects of any kind into this CCTV product through openings as they may touch dangerous voltage points or short-  
out parts that could result in a fire or electric shock. Never spill liquid of any kind on the CCTV product.  
Servicing  
Do not attempt to service this CCTV product yourself as opening or removing covers may expose you to dangerous voltages or  
other hazards. Refer all servicing to qualified service personnel.  
Damage Requiring Servicing  
Unplug this CCTV product from the wall outlet and refer servicing to qualified service personnel under the following conditions:  
a. When the power-supply cord or plug is damaged.  
b. If liquid has been spilled or objects have fallen into the CCTV product.  
c. If the CCTV product is not marked “Suitable for Wet Locations” and it has been exposed to rain or water.  
d. If the CCTV product does not operate normally by following the operating instructions. Adjust only those controls that are  
covered by the operating instructions as an improper adjustment of other controls may result in damage and often will  
require extensive work by a qualified technician to restore the CCTV product to its normal operation.  
e. If the CCTV product has been dropped or the cabinet has been damaged.  
f. When the CCTV product exhibits a distinct change in performance–this indicates a need for service.  
Replacement Parts  
When replacement parts are required, be sure the service technician has used replacement parts specified by Pelco or have the  
same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.  
Safety Checks  
Upon completion of any service or repairs to this CCTV product, ask the service technician to perform safety checks to  
determine that the CCTV product is in proper operating condition.  
WARNING  
This product has been evaluated for INDOOR USE ONLY unless it bears the marking FOR USE IN WET LOCATIONS.  
WARNING  
To reduce the risk of electric shock hazard, do not remove the cover of the unit. This unit can not be serviced by the user and  
must be sent to a qualified service person for repair when it fails to function.  
The lightning flash with an arrow head symbol within an equilateral triangle means that if the enclosure is  
opened, electrical circuitry is exposed which imposes an electric shock hazard to persons present.  
The exclamation point within an equilateral triangle means the operating instructions contain important  
information on how to operate and maintain the appliance.  
C2902M (10/02)  
5
 
DESCRIPTION  
The PMM9A, PMM12A, PMM15A, and PMM20A are high resolution, black and white, CCTV video monitors. The cabinets are  
made of steel for ruggedness and, with the exception of the picture tube, the circuitry is all solid-state for reliability.  
MODELS  
PMM9A  
Black and white monitor, 9-inch (22.86 cm) picture display, 96-256 VAC, 50/60 Hz, EIA/CCIR, auto-sensing  
Same as PMM9A except 12-inch (30.48 cm) picture display  
Same as PMM9A except 15-inch (38.10 cm) picture display  
PMM12A  
PMM15A  
PMM20A  
Same as PMM9A except 20-inch (50.80 cm) picture display  
INSTALLATION  
The following parts are supplied:  
Monitor  
Two power cords (1 USA standard and 1 European standard)  
MOUNTING  
The monitor has rubber feet and may be placed on any horizontal surface, such as a desk or table. The monitor also can be  
mounted to a wall or ceiling with an appropriate mount. If you have a PMM9A, PMM12A, or PMM15A monitor, it can be  
installed in a 19-inch equipment rack with a suitable rack-mounting kit. For mounting to a wall or ceiling or in a rack, refer to  
the instructions with the mount.  
CONNECTIONS  
SINGLE-MONITOR INSTALLATION  
Refer to Figure 1 and Table A for the following instructions.  
1. Set the impedance switch on the back of the monitor to LO (75 ohms).  
2. Connect a 75-ohm video cable from the video source, such as a camera, to the BNC connector labeled VIDEO IN (or  
INPUT) on the back of the monitor.  
3. Plug in the appropriate power cord.  
Figure 1. Singe-Monitor  
Installation (PMM15A Shown)  
6
C2902M (10/02)  
 
MULTIPLE-MONITOR INSTALLATION  
Refer to Figure 2 and Table A for the following instructions.  
1. Connect a 75-ohm video cable from the video source, such as a camera, to the BNC connector labeled VIDEO IN (or  
INPUT) on the back of the first monitor.  
2. Connect a 75-ohm video cable from the VIDEO OUT (or OUTPUT) connector on the back of the first monitor to the VIDEO  
IN (or INPUT) connector on the second monitor.  
3. If you are using a third monitor, connect a 75-ohm video cable from the VIDEO OUT (or OUTPUT) connector on the back of  
the second monitor to the VIDEO IN (or INPUT) connector on the third monitor.  
NOTE: In multiple-monitor installations, a maximum of three monitors can be connected together.  
4. Set the impedance switch on the first monitor to HI.  
If you are only using two monitors, set the impedance switch on the second monitor to LO (75 ohms).  
If you are using three monitors, set the impedance switch on the second monitor to HI and on the third monitor to LO  
(75 ohms).  
5. Plug in the appropriate power cords for the monitors.  
Figure 2. Multiple-Monitor Installation (PMM15A Shown)  
Table A. Video Coaxial Cable Requirements  
Cable Type*  
Maximum Distance  
RG59/U  
RG6/U  
750 ft (229 m)  
1,000 ft (305 m)  
1,500 ft (457 m)  
RG11/U  
* Minimum cable requirements:  
75 ohms impedance  
All-copper center conductor  
All-copper braided shield with 95% braid coverage  
C2902M (10/02)  
7
 
OPERATION  
Controls are located on the front of the monitor. On the PMM9A, PMM12A, and PMM15A, some or all of the controls are  
behind a hinged cover. Refer to Figure 3.  
Power On/Off Switch – This rocker switch turns the power on or off. Push the side with the white line to turn on the power.  
Push the side with the white circle to turn the power off.  
LED Power Indicator – The LED lights when power is turned on.  
Brightness Control – This control adjusts the overall picture brightness to compensate for differences in room lighting.  
Figure 3. Location of Controls (PMM15A Shown)  
Contrast Control – This control adjusts the contrast  
between the black and white portions of the picture. When  
properly adjusted, you will be able to observe a fine  
gradation between blacks, grays, and whites.  
Vertical Hold Control (Except PMM20A) – This control  
permits adjustment of vertical stability. If the picture “rolls”  
upward or downward, as shown in Figure 4, turn the  
VERTICAL HOLD clockwise or counterclockwise until the  
picture stabilizes.  
Horizontal Hold Control (Except PMM20A) – This  
Figure 4. Vertical Roll  
control permits adjustment of horizontal stability. If the  
picture “tears” to the left or right, as shown in Figure 5, turn  
the HORIZONTAL HOLD clockwise or counterclockwise until  
the picture stabilizes.  
To operate a monitor:  
1. Make sure a standard 1.0 V peak-to-peak video signal  
is applied to the video input of the monitor.  
2. Press the power switch to turn on the power. The  
power indicator LED will illuminate.  
3. Adjust the brightness and contrast controls to obtain  
optimum picture quality.  
Figure 5. Horizontal Tear  
8
C2902M (10/02)  
 
MAINTENANCE  
The only maintenance required is to clean the cabinet and screen periodically.  
Use a damp cloth to clean the screen.  
Use mild soap and water to clean the cabinet. Some common household aerosol sprays, cleaning agents, solvents, or polishes  
may damage the cabinet finish. Dry the cabinet with a soft cloth.  
C2902M (10/02)  
9
 
SPECIFICATIONS  
ELECTRICAL  
Input Voltage:  
96-256 VAC, 50/60 Hz, auto-ranging  
Power Consumption  
PMM9A:  
28 W  
30 W  
35 W  
48 W  
PMM12A:  
PMM15A:  
PMM20A:  
Input Signal:  
Input Impedance:  
Bandwidth:  
0.5 to 2.0 Vp-p composite video  
75 ohms or high (switchable)  
100 Hz to 10 MHz  
Resolution:  
>1,000 lines  
Linearity  
Horizontal:  
Vertical:  
10% maximum  
10% maximum  
Operating System  
EIA  
Horizontal:15,750 Hz ±400 Hz  
Vertical: 60 Hz  
CCIR  
Horizontal:15,625 Hz ±400 Hz  
Vertical: 50 Hz  
GENERAL  
Environment:  
Construction:  
Finish:  
Indoor  
Steel cabinet with black plastic front  
Black matte texture coat finish  
Dimensions  
PMM9A:  
9.3 (H) x 8.7 (W) x 9.9 (D) inches (23.5 x 22.0 x 25.2 cm)  
12.3 (H) x 12.2 (W) x 12.0 (D) inches (31.3 x 31.0 x 30.5 cm)  
12.8 (H) x 14.3 (W) x 13.1 (D) inches (32.6 x 36.2 x 33.2 cm)  
18.6 (H) x 19.3 (W) x 14.2 (D) inches (47.3 x 49.0 x 36.1 cm)  
PMM12A:  
PMM15A:  
PMM20A:  
Picture Tube  
Dimension  
PMM9A:  
9 inches (22.86 cm), measured diagonally  
12 inches (30.48 cm), measured diagonally  
15 inches (38.10 cm), measured diagonally  
20 inches (50.80 cm), measured diagonally  
PMM12A:  
PMM15A:  
PMM20A:  
Operating  
Temperature:  
32° to 122°F (0° to 50°C)  
Storage  
Temperature:  
14° to 140°F (-10° to 60°C)  
Relative Humidity: 10 to 95 percent, non-condensing  
Weight  
PMM9A:  
10.45 lb (4.75 kg)  
17.50 lb (7.94 kg)  
24.15 lb (10.94 kg)  
44.25 lb (20.08 kg)  
PMM12A:  
PMM15A:  
PMM20A:  
(Design and product specifications subject to change without notice.)  
10  
C2902M (10/02)  
 
REGULATORY NOTICES  
NOTE: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of  
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee  
that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct  
the interference by one or more of the following measures:  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment. Exceptions to this warranty are  
as noted below:  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to  
obtain a Repair Authorization number (RA), and provide the following information:  
1. Model and serial number  
Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600  
Series); two years on all other cameras.  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Three years on Genex® Series (multiplexers, server, and keyboard).  
Two years on cameras and all standard motorized or fixed focal length lenses.  
Two years on Legacy®, Camclosure® Camera Systems, CM6700/CM6800/CM8500/CM9500/  
CM9740/CM9760 Matrix, DF5 and DF8 Series Fixed Dome products.  
Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in continuous  
motion applications.  
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions  
stated above, please include a written explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by which the item was received by  
Pelco.  
Two years on WW5700 series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applica-  
tions (that is, preset scan, tour and auto scan modes).  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-  
9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA  
number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and  
freight should be prepaid. Ship to the appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the  
specific use or application made of the Products. Pelco’s liability for any claim, whether based on  
breach of contract, negligence, infringement of any rights of any party or product liability, relating  
to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no  
event will Pelco be liable for any special, incidental or consequential damages (including loss of  
use, loss of profit and claims of third parties) however caused, whether by the negligence of  
Pelco or otherwise.  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico:  
Intermediate Consignee  
American Overseas Air Freight  
320 Beach Road  
Burlingame, CA 94010  
USA  
Ultimate Consignee  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
USA  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
REVISION HISTORY  
Manual #  
Date  
Comments  
C2902M  
10/02  
Original version.  
® Pelco, the Pelco logo, Spectra, Genex, Legacy, Esprit, and Camclosure are registered trademarks of Pelco.  
C2902M (10/02)  
© Copyright 2002, Pelco. All rights reserved.  
11  
 
®
World Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada  
 

Pelco Wheelchair BB5HD User Manual
Philips Digital Camera SPC500NC User Manual
Philips MP3 Docking Station DC315 12 User Manual
Philips Stereo System MX970 User Manual
Planon System Solutions Scanner RC810 User Manual
Polaroid Digital Camera KM1200 E010 User Manual
Polaroid Digital Camera SL62 b w User Manual
Poulan Snow Blower 406281 User Manual
Poulan Tiller 168493 User Manual
ProForm Home Gym 83115032 User Manual