Installation and Assembly:
Flat Panel Pull-out Swivel Wall Mount for 26" - 58"
Screens
Models: SP 850, SP 850P, SP 850-S, SP 850P-S
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.
R
Max Load Capacity: 150 lb (68 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
Parts List
SP850
Qty. Part #
SP850P
Part #
SP850-S
Part #
SP850P-S
Part #
Description
wall mount assembly
locking tab
1
1
1
4
4
2
4
4
4
1
201-0385
200-1871
540-1032
201-0386
200-1871
540-1032
201-0383
200-4871
540-1032
201-0384
200-4871
540-1032
A
B
C
D
E
F
G
K
L
.219 ID x .5 OD x .125H spacer
#14 x 2.5" hex head wood screw
Alligator® anchor
18" polyester mesh sleeve
cable tie
M10 x 15 mm socket head screw
.198 x .313 x .437H retaining spacer
4 mm security allen wrench
5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03
590-0097
600-1014
560-9711
520-9262
590-5005
560-1146
Security
590-0097
600-1014
560-9711
520-9262
590-5005
n/a
Phillips
(not shown)
520-1233
504-9013
504-9020
520-1199
590-0097
600-1014
560-9711
520-9262
590-5005
560-1146
Security
590-0097
600-1014
560-9711
520-9262
590-5005
n/a
Phillips
(not shown)
520-1233
504-9013
504-9020
520-1199
M
M5 x 10 mm screw
M4 x 12 mm screw
M4 x 20 mm screw
M5 x 40 mm screw
5
4
4
1
520-1063
510-1079
510-1061
510-1001
520-1063
510-1079
510-1061
510-1001
AA
BB
CC
DD
Some parts may appear slightly different than illustrated.
L
G
K
A
BB
M
CC
B
AA
E
C
F
DD
D
Snap installation tab off of wall mount assembly (A).
1
A
INSTALLATIONTAB
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
3 of 10
Installation to Wood Stud Wall
WARNING
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
Using a stud finder, locate the edges of the wood studs used in mounting this product. Use of an edge-to-edge stud
2
finder is highly recommended. Based on its edges and using a level, draw a vertical line down the center of each
stud. Mark a point (point 1) on the right stud centerline where upper right slot will be located. Using a level, mark a
point (point 2) on the left stud centerline level with point 1 as shown in figure 2.1. Drill 5/32" diameter holes 2-1/2"
deep through studs at the two points. Loosely fasten wall mount assembly (A) to wall using two #14 x 2-1/2" wood
screws (D) as shown in figure 2.2. Level, hold, and then tighten screws.
Mark two more points for bottom slots on the right and left stud centerlines. Drill 5/32" diameter holes 2-1/2" deep
through studs at the two points. Using two #14 x 2-1/2" wood screws, fasten bottom of wall mount assembly to wall
as shown in figure 2.3.
Skip to step 3 on page 6.
CL
CL
POINT1
POINT2
D
A
fig 2.2
fig 2.1
CL = stud centerline
WARNING
• Tighten wood screws so that wall plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
D
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into
the center of the stud. The use of an "edge to edge"
stud finder is highly recommended.
A
fig 2.3
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
4 of 10
Installation to Solid Concrete and Cinder Block Wall
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.
It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid
breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
Position wall mount assembly (A) at desired position on
2
concrete
wall
wall. Use wall mount assembly, making sure that it is
level, as a template to mark holes. Drill four 1/4" (6 mm)
dia. holes to a minimum depth of 2-1/2" (64 mm). Con-
crete must be 2000 psi density minimum. Insert anchors
(E) in holes flush with wall as shown in figure 2.4. Place
wall mount assembly over anchors and secure with #14 x
2-1/2" (6 mm x 65 mm) wood screws (D) as shown in
figure 2.5. Make sure wall plate is level and tighten all
fasteners.
1
E
Drill holes and insert anchors
2
A
WARNING
• Tighten wood screws firmly, but do not overtighten.
Overtightening can damage the screws, greatly
reducing their holding power.
D
E
Place wall plate (A) over anchors and secure with
• Never tighten in excess of 80 in • lb (9 N.M.).
screws (D)
3
WARNING
• Concrete anchors are not intended for attachment to
concrete wall covered with a layer of plaster, drywall,
or other finishing material as shown below. If mounting
to concrete wall covered with plaster/drywall is
unavoidable, plaster/drywall (up to 5/8" thick) must be
counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when tighten-
ing screws. If plaster/drywall is thicker than
Tighten all fasteners
fig 2.4
5/8", custom fasteners must be supplied by installer.
E
INCORRECT
CORRECT
D
concrete
concrete
A
A
plaster/
dry wall
plaster/
dry wall
A
fig 2.5
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
5 of 10
Place installation tab over sliding arms of wall mount assembly (A) to lock them in place.
3
INSTALLATIONTAB
SLIDINGARM
A
FOR INSTALLING TO VESA 100 MM, 200 MM HOLE PATTERN
WARNING
• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not
tightly secured, damage may occur to screen or product may fail. Contact customer care for correct hardware to use.
Find the VESA® hole pattern as shown in figures 4.1 and 4.2, and attach screen to mounting plate as specified
below. Verify that all holes are properly aligned, and then tighten screws. If using security screws, tighten using
security allen wrench (M).
4
VESA 100
VESA 200
fig. 4.1
fig. 4.2
FORVESA100MOUNTINGPATTERN:
Thread two M4 x 12 mm screws (BB), leaving .25" exposed thread, into top holes on back of screen. Hook screen
onto mounting plate, and attach using bottom two M4 x 12 mm screws as shown in figures 4.3 and 4.4. (page 7)
Tighten all four screws.
Note: If screw (BB) is too small to engage threaded inserts, attach mounting plate to back of screen using four M5 x
10 mm screws (AA).
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
6 of 10
FORVESA200MOUNTINGPATTERN:
Thread two M4 x 12 mm screws (BB), leaving .25" exposed thread, into top holes on back of screen. Hook screen
onto mounting plate, and attach using two bottom M4 x 12 mm screws as shown in figures 4.3 and 4.4. Tighten all
fourscrews.
FORSCREENSWITHVESAMOUNTINGPATTERNINAPOCKET:
Thread two retaining spacers (L) onto two M4 x 20 mm screws (CC), leaving .25" exposed thread as shown in figure
4.5. Thread M4 x 20 mm screws with retaining spacers into top holes on back of screen. Hook screen onto mounting
plate, and attach using bottom two M4 x 20 mm screws and retaining spacers as shown in figures 4.3 and 4.4.
Tighten all four screws.
fig. 4.5
For screens with a hole
pattern in a pocket,
spacers (L) go between
mounting plate and
screen.
MOUNTING PLATE
MOUNTING PLATE
(NOTE: MOUNTING PLATE
SHOWN WITHOUT FULL
WALL MOUNTASSEMBLY
FOR CLARITY)
(NOTE: MOUNTING PLATE
Note: Flat panel screen
may appear slightly
different than illustrated.
SHOWN WITHOUT FULL
WALL MOUNTASSEMBLY
FOR CLARITY)
fig. 4.3
fig. 4.4
For screen compatibility please refer to the plasma interface list on our website www.peerlessmounts.com or
call customer care for a screen specific adapter bracket (PLP models).
FOR INSTALLING TO PEERLESS PLP MODELADAPTER BRACKET (not UL listed)
Note: Refer to PLP model adapter bracket instruction sheet for attachment of adapter bracket to screen.
Thread two M10 x 15 mm screws (K), leaving .25" exposed thread, into top holes on back of screen. Hook screen
onto mounting plate, and attach using two bottom M10 x 15 mm screws as shown in figures 5.7 and 5.8. Tighten
screws using 6 mm allen wrench (not included).
5
GENERICADAPTER
BRACKET
GENERIC
ADAPTER
BRACKET
MOUNTINGPLATE
K
K
MOUNTING PLATE
(NOTE: MOUNTING PLATE
SHOWN WITHOUT FULL
WALL MOUNTASSEMBLY
FOR CLARITY)
fig. 5.8
fig. 5.7
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
7 of 10
Slide one mesh sleeve (F) over each cable. Use
cable ties (G) to tighten both ends of mesh sleeves
to cables.
Optional: To lock mount in closed position, insert
one M5 x 40 mm screw (DD) into tapped hole in
either top or bottom of flat plate.
7
6
Note: loop cable ties through cable mounts and
Note: Screen not shown for clarity.
tighten cable and mesh sleeve to cable mounts.
DD
TAPPED HOLE
TAPPED HOLE
G
CABLE MOUNTS
FLAT
PLATE
F
Screen can tilt 5° or 10° forward.
Note: Screen must be securely attached to mounting plate with all fasteners before adjusting tilt.
8
To tilt screen 5° forward, lift and pull mounting plate forward until middle notch rests on M6 screw as shown in figure
8.1. Tighten M6 screw (both sides) and M10 screws (both sides).
To tilt screen 10° forward, lift and pull mounting plate forward until rear notch rests on M6 screw as shown in figure
8.2. Tighten M6 screw (both sides) and M10 screws (both sides).
Note: For security models, tighten M6 screw using security allen wrench (M). For all M10 screws, use 6 mm allen
wrench (not included).
M6 SCREW
M6 SCREW
MOUNTING
PLATE
MOUNTING
PLATE
M10 SCREW
M10 SCREW
5° tilt
10° tilt
fig. 8.1
fig. 8.2
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
8 of 10
Roll can be adjusted 1° clockwise or
counterclockwise.
Optional: To lock one sliding arm of mount in place,
slide locking tab (B) over top or bottom of sliding arm
and attach to mount using one M5 x 10 mm screw
(AA) and one spacer (C).
9
10
To adjust roll, loosen screen fasteners slightly,
leaving them snug. Level screen, then tighten screen
fasteners.
Note: Screen not shown for clarity.
NOTE: When adjusting roll, screws should be
retightened as indicated in step 4.
AA
B
C
SLIDINGARM
SCREENFASTENER
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
9 of 10
Screen Compatibility Chart
Manufacturer
Apex
Dell
Screen Manufacturer Model
Manufacturer
Screen Manufacturer Model
Size
Size
27"
26"
30"
26"
30"
30"
26"
32"
26"
26"
26"
26"
27"
30"
30"
30"
30"
32"
32"
26"
32"
27"
30"
32"
30"
30"
30"
30"
30"
26"
32"
27"
30"
26"
26"
30"
32"
32"
27"
30"
30"
32"
32"
26"
26"
26"
26"
30"
AVL-2776
W2600
W3000
Sharp
Sharp
26"
26"
26"
26"
26"
26"
26"
30"
30"
30"
26"
26"
26"
26"
27"
30"
32"
37"
27"
30"
26"
26"
32"
27"
27"
27"
30"
30"
32"
37"
32"
27"
IT-26M1U
LC-26D5U
LC-26D7U
LC-26GA4U
LC-26GD4U
LC-26GD6U
LD-26SH1U
LC-30HV2U
LC-30HV4U
LC-30HV6U
KLV-26HG2
KLVS26A10
LT26HV
Dell
Sharp
Sharp
Gateway
Gateway
Hewlett Packard
Hyundai
Hyundai
LG
GTW-L26M103
GTW-L30M103
LC3040N
Sharp
Sharp
HQL260WR
HQL320WR
26LX1D
Sharp
Sharp
Sharp
Sharp
LG
LG
RM-26LZ30
RU-26LZ30
Z26LZ5R
Sony
Sony
LG
LG
RU-27LZ50C
DU-30LZ30
L3000H
Syntax/Olevia
Syntax/Olevia
Syntax/Olevia
Syntax/Olevia
Syntax/Olevia
Syntax/Olevia
Tatung
LG
LG
LT26HVX
LT27HV
LT30HV
LG
LG
L3020T
RU-30LZ50C
RU-32LZ30C
RU-32LZ50C
26MF605W/17
32MF605W/17
MX-27X1
LT32HV
LT37HV
LG
LG
V27CMTT
V30CMTT
26HL83
Magnavox
Magnavox
MAXENT
MAXENT
MAXENT
Mitsubishi
Mitsubishi
Mitsubishi
Mitsubishi
NEC-Mitsubishi
NuVision
NuVision
Ovideon
Ovideon
Philips
Tatung
Toshiba
Toshiba
Toshiba
26HL84
32HL84
N2750w
MX-30X1
MX-32X3
Viewsonic
Westinghouse
Westinghouse
Westinghouse
Westinghouse
Westinghouse
Westinghouse
Winbook
Zenith
LT-3020
LT-3040
LTV-27w2
W32701
W33000
LT-3050
MLM300
LCD3000
W33001
LTV-32w1
LVM-37w1
LC32
NVX26HDU
NVX32HDU
LC2700w
L27W46
LC3000W
26MF605W/17
26PF9966
300WN5VB
32MF605W/17
32PF5320
PX-27XP10
PX-30XP10
LC30D
Philips
Philips
Philips
Philips
PixelPro
PixelPro
PowerSpec
Pro View
Protron
Samsung
Samsung
Samsung
Samsung
Sceptre
RX-326
PLTV32C
LN-R2668W
LN-R267W
LN-R268W
LT-P266W
X30SV- Naga III
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
10 of 10
©2007, PeerlessIndustries, Inc. Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
|