848101 LAT OPTION
ASSEMBLY INSTRUCTIONS
Revision: 5/26/99
Part # 6826701
1
PARTS LIST
KEY PART #
DESCRIPTION
BASE
QTY
1
KEY PART #
DESCRIPTION
1-1/4”RUBBERBUMPER
1 X 1” GLIDE
QTY
1
1
2
6824303
6823703
6825403
6824103
6825502
6275302
6274402
6542402
6824801
3103102
3116201
6177001
6405201
6467001
6692601
6825101
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
3116001
6140701
3102501
3102802
3102502
3102801
3102933
3102903
3102922
3102935
3102910
3103801
3108102
6122703
6480301
6127701
UPRIGHT
1
8
3
STAND
1
3/8” WASHER
12
11
2
4
CROSSBRACE
CARRIAGE
1
3/8” LOCK NUT
5
1
1/2” WASHER
6
LATBAR
1
1/2” LOCK NUT
1
7
LOW ROW BAR
3/16 X 1-3/4 X 5-1/4” PLATE
CABLE
1
3/8 X 2” BOLT
2
8
2
3/8 X 2-1/2” BOLT
3/8 X 2-3/4” BOLT
3/8 X 4-1/2” BOLT
1/2 X 3” BOLT
2
9
2
6
10
11
12
13
14
15
16
1 X 8” GRIP
4
1
3-1/2”PULLEY
2-1/2 X 5-1/2” NON-SKID STRIP
2” SQ. END CAP
2” SQ COVER CAP
3 X 2” END CAP
17-1/2” FOAM STRIP
6
1
2
5/16” SNAP LINK
1/4” QUICK DISCONNECT LINK
3/8 X 3/8” SPACER
3/8” FLANGE SPACER
3/8 X 1” SPACER
2
4
1
2
2
3
6
1
1
3
20
19
3/8 X 2-3/4” 25
14
3
13
FIGURE 1
STEP 1:
• Assemble two 2” SQ. COVER CAPS (14) onto the ends of the STAND (3) as shown in FIGURE 1.
• SECURELY assemble the one 3/8 X 2-3/4” BOLT (25), two 3/8” WASHERS (19), and one 3/8” LOCK NUT (20) to the STAND (3) as
shown in FIGURE 1.
• Assemble one 2” SQ. END CAP (13) into the end of the STAND (3) as shown in FIGURE 1.
15
1
FIGURE 2
STEP 2:
• Insert two 3 X 2” END CAP (15) into the ends of the BASE (1) as shown in FIGURE 2.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
4
12
13
4
16
FIGURE 3
STEP 3:
• Insert two 2” SQ. END CAPS (13) into the ends of the CROSS BRACE (4) as shown in FIGURE 3.
• Assemble two 2-1/2 X 5-1/2” NON-SKID STRIPS (12) to the CROSS BRACE (4) as shown in FIGURE 3.
• Assemble one 17-1/2” FOAM STRIP (16) to the underside of the CROSS BRACE (4) as shown in FIGURE 3.
5
18
17
FIGURE 4
STEP 4:
• Attach eight 1 X 1” GLIDES (18) to the ends the CARRIAGE (5) as shown in FIGURE 4 using the following steps:
• Thoroughly clean all surfaces where the 1 X 1” GLIDES (18) are to be attached.
• Remove the 1 X 1” GLIDES (18) from the paper backing and firmly apply them to all shown surfaces.
• SECURELY attach one 1-1/4” SQ. RUBBER BUMPER (17) to the CARRIAGE (5) as shown in FIGURE 4.
5
STEP 5:
• Assemble the STAND (3) to the UPRIGHT (2) as
shown in FIGURE 5.
• Slide the CARRIAGE (5) over the UPRIGHT (2) as
shown in FIGURE 5.
• Assemble the BASE (1) to the UPRIGHT (2) as
shown in FIGURE 5.
2
5
1
3
FIGURE 5
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
6
13
15
2
20
19
4
21
22
3/8 X 2-3/4” 25
21
1
27 1/2 X 3”
FIGURE 6
STEP 6:
• SECURELY assemble the BASE (1) to the UPRIGHT (2) using one 1/2 X 3” BOLT (27), two 1/2” WASHERS (21) (slide front washer
INSIDE of tube), and one 1/2” LOCK NUT (22). See FIGURE 6.
• Insert one 3 X 2” END CAP (15) and one 2” SQ. END CAP (13) into the ends of the UPRIGHT (2) as shown in FIGURE 6.
• SECURELY assemble the CROSS BRACE (4) to the UPRIGHT (2) using two 3/8 X 2-3/4” BOLTS (25), two 3/8” WASHERS (19), and two
3/8” LOCK NUTS (20). See FIGURE 6.
7
2
20
31
9
3/8 X 2-3/4” 25
11
FIGURE 7
STEP 7:
• Route the CABLE (9) through the UPRIGHT (2) as shown in FIGURE 7.
• SECURELYassemble three 3-1/2” PULLEYS (11) into the slots of the UPRIGHT(2) using three 3/8 X 2-3/4” BOLTS (25), six 3/8” FLANGE
SPACERS (31), and three 3/8” LOCK NUTS (20) as shown in FIGURE 7. (NOTE: Make sure the cable is routed over all the pulleys.)
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
8
2
19
20
19
11
8
23 3/8 X 2”
9
SECURELY
TIGHTEN!
29
5
FIGURE 8
STEP 8:
• Attach the CABLE (9) from the UPRIGHT (2) to the CARRIAGE (5) using one 1/4” QUICK LINK (29) as shown in FIGURE 8. (IMPOR-
TANT! Securely tighten QUICK LINK.)
• Place one 3-1/2” PULLEY (11) into the loop of the CABLE (9) below the second and third PULLEY of the UPRIGHT (2) as shown in
FIGURE8.
• LOOSELY assemble two 3/16 X 1-3/4 X 5-1/4” PLATES (8) to each side of the 3-1/2” PULLEY(11) using one 3/8 X 2” BOLT (23),
two 3/8” WASHERS (19), and one 3/8” LOCK NUT (20). See FIGURE 8.
9
2
8
20
19
19
11
23 3/8 X 2”
9
20
30
19
11
24 3/8 X 2-1/2”
FIGURE 9
STEP 9:
•
Route the end of the second CABLE (9) through the slot on the UPRIGHT (2) then SECURELYassemble one 3-1/2” PULLEY (11) to
the UPRIGHT (2) using two 3/8 X 2-1/2” BOLTS (24), two 3/8 X 3/8” SPACERS (30), four 3/8”WASHERS (19), and two 3/8” LOCK NUTS
(20). (NOTE: The CABLE (9) should be routed between the pulley and the retaining bolt as shown in FIGURE 9.)
• Loop the CABLE (9) around one 3-1/2” PULLEY (11) as shown in FIGURE 9.
• LOOSELYassemble the 3-1/2” PULLEY(11) to the 3/16 X 1-3/4 X 5-1/4” PLATES (8) using one 3/8 X 2” BOLT (23), two 3/8” WASHERS
(19), and one 3/8” LOCK NUT (20). See FIGURE 9.
• SECURELYtighten the two 3/8 X 2” BOLTS (23) of the 3/16 X 1-3/4 X 5-1/4” PLATES (8).
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
10
9
20
1
32
26 3/8 X 4-1/2”
FIGURE 10
STEP 10:
• SECURELYassemble the CABLE (9) to the BASE (1) using one 3/8 X 4-1/2” BOLT (26), one 3/8 X 1” SPACER (32), and one 3/8” LOCK
NUT (20) as shown in FIGURE 10.
11
9
10
28
6
9
28
7
10
FIGURE 11
STEP11:
• Slide two 1 X 8” GRIPS (10) on the LOW ROW BAR (7) and two 1 X 8” GRIPS (10) on the LAT BAR (6) as shown in FIGURE 11.
• Attach the LAT BAR (6) to the ball end of the upper CABLE (9) using one 5/16” SNAP HOOK (28) as shown in FIGURE 11.
• Attach the LOW ROW BAR (7) to the ball end of the lower CABLE (9) using one 5/16” SNAP HOOK (28) as shown in FIGURE 11.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
12
3
FIGURE 12
STEP 12:
• To use the 848101 LATOPTION: (NOTE: LAT OPTION MUST BE USED WITHABENCH. LAT OPTION CANNOT BE USED
WHILESTANDISATTACHED. STANDMUSTBEATTACHEDWITHTHEFEETOUTASSHOWN.)
• Tilt the 848101 back and remove the STAND (3) as shown in FIGURE 12.
13
2
BENCH
FIGURE 13
STEP 13:
• Insert the UPRIGHT (2) of the 848101 into the bench as shown in FIGURE 13.
Thank you for purchasing the Parabody 848101 LAT OPTION. If unsure of proper use of equipment, call
your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
14
|