Rear-View Camera
Model
CY-RC50KN
CY-RC50KW
Operating Instructions
CAMERA
IN
VIDEO
OUT
POWER
O
Please read these instructions carefully before using this product and keep this
manual for future reference.
Caution
Observe the following cautions
when using this unit.
R Do not use this system for any purpose other
than mounting on a road vehicle.
Non-vehicular use (such as use outdoors
or on a pleasure boat) could cause smoking
generation, ignition, electric shock, injury and
breakdown.
R Do not damage the rear view camera cord.
Water and moisture can move along the cord
from the damaged area and enter the camera,
causing fire, electric shock and breakdown.
R Route the rear view camera cord inside
the vehicle, so that water cannot penetrate
them.
If water enters the vehicle during rain or car
washing, it could cause fire or electric shock.
R Order wiring, mounting and dismounting
work from a specialist engineer.
R Do not use an automatic car–washing
machine to wash the vehicle.
Wiring, mounting and dismounting work
requires specialist skills and experience. For
safety, ask your dealer to perform such work.
In the case that this system is installed in a
vehicle with a drive computer or a navigation
system, improper removal of the battery may
result in erasure of system’s memory.
R Only use the accessories provided and the
parts specified.
Use of non-specified parts can cause internal
damage to the equipment, and insecure
mounting could allow it to fall off, causing
accident, breakdown and fire.
Exposure to water from a high pressure hose
or impact from a brush may cause the system
to fall resulting in accident or injury. Water
entering inside the camera can result in a fire,
electric shock or breakdown.
Observe the following cautions
when installing.
R Do not damage cords.
Do not damage, pull, bend, twist or modify
cords, place heavy objects on them, or place
them near hot equipment or in contact with
hot parts of the vehicle. Breaking or shorting
cords could cause fire, electric shock, or
accidents.
R Mount the equipment securely, so that it
cannot come off and fall.
Wipe the mounting area clean of dirt, wax
etc., then fasten the camera securely in place.
Re-affixing adhesive parts or use of general-
purpose double-sided tape could cause weak
bonding that would allow the equipment to
drop off while the vehicle is in motion, causing
accident or injury. Check the state of bonding
or mounting (loose screws etc.) occasionally.
O
Route cords so that they cannot be pinched
by the body of the vehicle, screws or
moving parts (seat rails etc.).
Do not press cords with the point of a
O
screwdriver or similar implement.
Notes on use
Carefully read the instruction manuals for the connected devices (Car
Monitor etc.).
Before reversing, always check behind you by eye.
O
This product uses mirrored display (which mimics the orientation of the rear-view and side
mirrors), and is for checking the view behind the vehicle.
It is intended to augment the driver’s field of vision behind the vehicle. It is not able to view
O
all hazards and obstacles.
It uses a wide-angle lens, which makes close areas appear wider and further areas narrower.
O
This may cause perceived distances to differ from actual distances.
This product can be connected to a monitor etc. with RCA-type video inputs. When the
shift lever is in reverse (R), the linkage function (camera interrupt display) and scaled
display correspond to the connected display device, so we are unable to guarantee normal
operation.
Check the mounting of the system components regularly
O
Check that there are no loose screws, and that the camera bracket is not detached.
Check that the rubber water seals where the cord enters the vehicle are parallel to the rubber
O
gasket where they are in contact.
Do not display a direct view of the sun for long periods
O
A burned image could remain on the screen.
Do not use a cellular telephone or wireless equipment close
to the system
O
Screen noise and malfunctions could result.
You are advised to use cellular telephone or wireless equipment away from this system.
Disclaimers
O
Any repairs to breakdowns or damage caused by fire, earthquake, third-party action, other
accident, actions of the user, whether by accident or design, incorrect operation or usage
under other abnormal conditions will, as a rule, require payment of repair fees.
Not guaranteed when equipped in a commercial-use vehicle (buses, trucks, taxis, goods
O
vehicles etc.).
Memorandum
Specifications
Output image ...........................................Wide-angle mirror image (for checking the rear view)
Video format .....................................................................................................NTSC composite
Power supply......................................................................................DC 12 V, negative ground
Power consumption..............................................................................1.6 W (approx. 135 mA)
Image sensor......................................................................... Colour CCD, solid-state, 6.35 mm
Effective pixels........................................................................................Approx. 250 000 pixels
Lens....................................................................... Wide angle, focal length f=1.94 mm, F 1:2.8
Angular field of view .................................................................. Horizontal: 134°, Vertical: 103°
S/N ratio................................................................. 46 dB or more (at recommended light level)
Horizontal resolution.............................................................................. 330 TV lines (at centre)
Brightness range...............................................................................Approx. 1.5 lx – 100 000 lx
Image output.........................................................................................................1 Vp-p (75 Ω)
Dimensions (W x H x D)
O
Rear view camera.......................................................................23 mm x 21 mm x 20 mm
(cord length 4 m, not including projections on the rear)
Rear view camera control unit....................................................76 mm x 27 mm x 40 mm
O
Weight
O
Rear view camera..................................................................Approx. 90 (including cord)
g
O
Rear view camera control unit....................................................................... Approx. 110
g
Note:
O
Specifications and the design are subject to modification without notice due to
improvements in technology.
Some figures and illustrations on this manual may be different from your product.
O
Direct Sales at Panasonic UK
Sales and Support Information
O
Order accessories and consumable items for your product with
ease and confidence by phoning our Customer Care Centre Monday
- Thursday 9:00am - 5:30pm, Friday 9:30am - 5:30pm. (Excluding
public holidays).
For UK and Ireland customers only.
O
Or go on line through our Internet Accessory ordering application at
Customer Care Centre
O
For customers within the UK:
O
O
Most major credit and debit cards accepted.
All enquiries, transactions and distribution facilities are provided
directly by Panasonic UK Ltd.
0844 844 3852
O
For customers within the Republic of
Ireland: 01 289 8333
O
O
It couldn’t be simpler!
O
Visit our website for product information
Also available through our Internet is direct shopping for a wide
range of finished products, so take a browse on our website for
further details.
O
E-mail: [email protected]
Matsushita Electric Industrial Co., Ltd.
YEFM285998 F0207-1047
Printed in Japan
Warning
Observe the following warnings
when installing.
R Route cords so that they do not get in the
way of occupants driving or getting into or
out of the vehicle.
ꢀ
Route cords so that they do not tangle with the
steering wheel, shift lever, brake pedals, feet
etc., and bundle and fasten them appropriately.
Poorly arranged cords can cause accident and
injury.
R Wire and mount the system as instructed.
Fire or accident could result if wiring and
mounting do not properly follow the operating
instructions.
R Use on a DC 12 V
grounded vehicle.
ꢀ
This system can only be used on a DC 12 V
grounded vehicle. It cannot be used in DC 24 V
and other battery system (large trucks, diesel
vehicles for use in cold regions, etc.). Use on
such vehicles would cause fire and breakdown.
R Disconnect the battery
performing any wiring or installation work.
Wiring or installation work with the battery
terminal connected could cause electric shock
and injury from shorting.
ꢀ
terminal during
ꢀ
R Do not attempt to disassemble, repair or
modify the system.
Never attempt to disassemble, repair or modify
the system, or to remove cord insulation to
take power supply from other devices. Fire,
electric shock or accident could result.
R After mounting and wiring the system, check
that all vehicle systems function normally.
If any vehicle equipment (brakes, lights, horn,
hazard and indicator lights etc.) does not work
normally, fire, electric shock or accident could
result.
R Keep screws and other small components
away from small children.
There is a risk that they could swallow
small components. Seek immediate medical
attention if that happens.
R
This system should be installed in a way so
that operation of vehicle protective devices
such as an air bag is not hindered.
Should this system be installed in a vehicle
with a protective device such as an air bag
or an anti-theft system, check with the car
manufacturer about operational cautions
prior to attempting installation and perform
the installation in a safe and proper manner.
Improper removal of the battery may result in
a malfunction of a device or possibly death.
R Never use the security parts of the vehicle
for mounting or grounding the system.
Use of the bolts or nuts of security parts
(steering, brake systems, fuel tank etc.) can
cause brake failure, fire, or other accidents.
R
Check positions of pipes, tanks, electric
wirings in the vehicle when mounting.
Never interfere with or touch pipes, tanks,
or electric wirings when opening holes in
the vehicle body for installation. Apply rust
prevention and waterproofing treatments to
the processed area, as rust or water leakage
may result in a fire, an electric shock, or other
accident.
Information on Disposal for Users of Waste Electrical & Electronic Equipment
(private households)
This symbol on the products and/or accompanying documents means that used
electrical and electronic products should not be mixed with general household
waste.
For proper treatment, recovery and recycling, please take these products to
designated collection points, where they will be accepted on a free of charge
basis. Alternatively, in some countries you may be able to return your products
to your local retailer upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and
prevent any potential negative effects on human health and the environment
which could otherwise arise from inappropriate waste handling. Please contact
your local authority for further details of your nearest designated collection
point.
Penalties may be applicable for incorrect disposal of this waste, in accordance
with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or
supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for
the correct method of disposal.
Troubleshooting
If you suspect something wrong
Check and take steps as described below.
If the described suggestions do not solve the problem, it is recommended to take the unit to
your nearest authorized Panasonic Service Centre. The product should be serviced only by
qualified personnel. Please refer checking and repair to professionals.
Panasonic shall not be liable for any accidents arising out of neglect of checking the unit or
your own repair after your checking.
Never take measures especially those other than indicated by italic letters in “Possible
solution” described below because those are too dangerous for users to handle
themselves.
Warning
O
Do not use the unit in an irregular condition, for example, without sound, or with smoke
or a foul smell, which can cause ignition or electric shock. Immediately stop using the
unit and consult your dealer.
Never try to repair the unit by yourself because it is dangerous to do so.
O
Problem
Possible cause ° Possible solution
O
O
Incorrect settings or connection.
°Check settings and cord connections.
The fuse for the system, or for equipment connected to it, has
blown.
No image from the
camera.
°Consult a Panasonic Service Centre.
O
O
Is there dust or dirt on the camera?
°Wipe the lens clean.
Image is unclear.
If the camera is viewing the sun directly, or a strong light
(reflection from a fender, a headlight beam etc.) shines into it,
bright vertical lines can appear above and below the light source.
(Smearing)
White lines (vertical
lines of light) on the
screen.
°This is not a breakdown.
O
O
When the area viewed by the camera is lit by fluorescent light or
a similar light source, noise can appear on the screen. (Flickering)
°This is not a breakdown.
Noise on the
screen.
The screen display may become hard to see when it shows a
dark area, or an image that is bright in a small area, or when the
camera is hot.
Screen display is
hard to see.
°This is not a breakdown.
Product servicing
If the suggestions in the charts do not solve the problem, we recommend that you take it to
your nearest authorized Panasonic Service Centre. The product should be serviced only by a
qualified technician.
Replacing the Fuse
Use fuses of the same specified rating (1 A). Using different substitutes or fuses with higher
rating, or connecting the product directly without a fuse, could cause fire or damage to this
unit.
If the replacement of the fuse fails, consult your nearest authorized Panasonic Service
Centre for service.
Maintenance
Caution on cleaning
O
Do not wipe with volatile chemicals, such as alcohol, benzine, thinners and gasoline. These
can cause deformation, deterioration and breakage.
Do not wipe with cleaners that contain abrasive particles, as they leave scratches.
If the lens is dirty, wipe it gently with a soft, moist cloth. Wiping strongly with a dry cloth
O
O
will damage the lens.
Alcohol
Benzine
Pesticide
Wax
Thinner
Check the contents
Consult your dealer if any item is missing.
O
Figures in ( ) are quantities.
Rear view camera
Rear view camera
Camera bracket
Bolts with washer
(with Rubber water seal) control unit
4 m cord
(1)
(1)
(1) M3 × 6 mm
(2)
(1)
(1)
Hexagon wrench
Power cord
RCA cord
Clip connector
(1) 5 m
(1) 6 m
(1)
Cord clamp
Cord rail
Tie band
Velcro tape
(7) 18 cm
(4)
(2) 38 × 70 mm
Double-sided tape
30 × 70 mm
(1)
Q Accessories
Operating instructions PAN EUROPEAN
(this manual)
GUARANTEE
(Warranty Card)
(1)
(1)
(CY-RC50KN only)
Cord routing (example)
O
Route the camera cord so that it does not allow rainwater etc. to penetrate.
Allow enough slack in the cord so that it is not pulled when the door is opened and closed.
O
Hatchback or Van type
Cord clamp
Route the cord above the back door
(outside).
Fasten with cord clamps at
key points, then bring the
cord in where the clearance
from the edge of the door
is wider.
Harness cover
Do not route the cord under the back
door (inside).
Tie band
Tie to the harness cover.
The cord will be damaged if
pinched by the edge of the
back door.
Car monitor etc.
Rear view camera
Rear view camera
control unit
Rubber water seal
(Attached to rear
view camera.)
Place against the rubber
gasket and bring the
cord into the interior.
Cord rail
(peel off backing paper)
Cut to the appropriate size.
Rear view camera cord
Cord clamp
Saloon type
Cord clamp
Boot lid
Rear view camera
Rubber gasket
View with boot lid closed
Rubber water seal
(Attached to rear view camera.)
Rubber water seal
(Attached to rear view camera.)
Rubber gasket
Attach the rubber water seal so that it is parallel with
the rubber gasket when the boot is closed.
Note:
O
Open and close the back door or boot lid slowly to check that the camera cord is not
pinched or abraded by the door/lid. Moisture or water can enter through the damaged area
of the cord and penetrate to the interior of the camera, causing breakdowns.
Route the camera cord as far as possible from the antenna cord.
(It could cause noise in TV and radio signals.)
O
O
If AM radio broadcasts are affected by noise, move the camera cord further from the vehicle
wiring harness.
Mounting procedure
Rear view camera
Before mounting
Wipe away all oil and dirt etc. from the mounting surface.
Make connections and placement tentatively at first, to check positions. Repeated
affixing weakens the adhesive.
O
The screw holes to use, and the possible angle adjustment, vary according to the
mounting position. Adjust the angle and check that the required field of view is
visible. (It is not possible to re-affix components.)
Mount the camera so that it does not contact the vehicle body or rear wipers.
O
QFor secure mounting
O
Do not work outdoors in rainy weather.
When the air temperature is low, use the vehicle’s interior heater or defogger, or a
O
dryer, to warm the bonding area.
Use a dryer etc. to thoroughly remove all moisture. Dirt and moisture on the bonding
O
surface reduce bond strength and could cause the camera to fall off.
After mounting the camera, do not expose it to rain or other water, pull it or subject it
O
to strong forces for 24 hours.
Note:
O
The camera cannot be affixed to painted or glass surfaces which have been treated
with fluoroplastics (treatments which shed water droplets, mud etc.), or to re-painted
surfaces.
Rear view camera control unit
Before mounting
Wipe away all oil and dirt etc. from the mounting surface.
Mounting on hard surfaces (floor
etc.)
Mounting on carpet etc.
Rear view camera control unit
Rear view camera control unit
Velcro tape
Double-sided tape
Note:
Do not mount the control unit in the following locations, which could cause breakdowns.
O
Places exposed to water
Places which could be stepped on
Dusty places
Close to heater ducts or heat-emitting objects
Places exposed to direct sunlight
Under the carpet, or any other position that gets hot
O
O
O
O
O
Wiring procedure
Make connections and set and operate acco
When connected to a Panasonic Car Monitor etc., the image from the camera is automatically
displayed in the screen when the shift lever is moved to reverse (R).
O
For some combinations of vehicle type and device, additional cords (option) may be
required, or connection may not be possible.
Consult your dealer or service centre.
For connection with products from other companies, consult the manufacturer of each
O
device.
Power connector (POWER)
Always wear gloves for safety during
wiring and mounting operations.
Camera input (CAMERA IN)
QInstallation procedure
Video output (VIDEO OUT)
ꢀ
ꢀ
Disconnect the battery terminal.
ꢁ
Make wiring connections.
CAMERA VIDEO
POWER
O
IN
OUT
To avoid short circuit accidents, do not
connect the power cord connectors until all
wiring is complete.
Rear view camera
control unit
ꢂ
Mount the components.
ꢀ
Reconnect the battery terminal.
(Yellow)
Power cord
(5 m)
RCA cord
(6 m)
(Yellow)
To camera image input terminal or video
input terminal
NTSC Only
Rear view camera
(4 m)
Ground lead
(Black)
GND
To a metal part of the vehicle body
Connect to an area of exposed metal, not
covered with paint etc.
Reverse lead
(Violet/white stripe)
ꢁ
1 A
To the
wire of the reverse lamp
REVERSE
Fuse 1 A
Do not connect to a point that has a
constant power supply.
Note:
O
Insert connectors securely. Also, take care to avoid pulling on the cords.
Do not extend the RCA cord or rear view camera cord, as video noise and breakdowns could
result.
O
O
Only use clip connectors in the specified places.
ording to the installation instructions for the connected devices.
Connection to a Car Monitor (example)
ꢁ
Connect to the
wire of the reverse lamp (lamp with a transparent lens, which
lights for reversing) which lights when the vehicle shift lever is moved to reverse (R).
Transmission
P
R
Reverse lamp
N
D
＋
－
L
2
Clip connector
Clip connector
Reverse extension cord
(Violet/white stripe)
Battery
1 A
Reverse lead
Ground lead
Car chassis
(Violet/white stripe) (Black)
Reverse lead
(Violet/white stripe)
Rear view camera
control unit
In-Dash Monitor
(CQ-VD7005N/W: option)
Rear view camera
(4 m)
(Yellow)
Camera input terminal
(Yellow)
RCA cord
(6 m)
(Yellow)
CAMERA-IN
Connection to a Car Monitor from another company (example)
ꢁ
Connect to the wire of the reverse lamp (lamp with a transparent lens, which
lights for reversing) which lights when the vehicle shift lever is moved to reverse (R).
Transmission
P
R
N
D
＋
－
Reverse lamp
L
2
Clip connector
Clip connector
Battery
Ground lead
REVERSE
1 A
GND
Video input
NTSC Only
Reverse lead
(Violet/white stripe) (Black)
Car chassis
Car Monitor
(Yellow)
Rear view camera
control unit
Rear view camera
(4 m)
(Yellow)
Reverse lead
RCA cord
(6 m)
Cut off the end terminal and
connect to the clip connector.
How to disconnect locked cords
How to attach a clip connector
O
ꢀ
Pulling strongly will break the cord.
Check that the lock is released before
disconnecting.
Insert the cord into the
clip connector.
O
Vehicle-side wiring cord
Reverse lead of this unit
Power cord
Rear view camera
cord
ꢁ
Press the element into
place.
ꢂ
Close the cover.
ꢀ
Attach the camera bracket to a glass or painted surface on the vehicle
body.
ꢃ
ꢂ
Form the camera bracket to
fit the form of the mounting
surface. (Do not remove the
backing paper)
Peel the backing paper and press the camera
bracket firmly onto the surface.
O
Do not touch the bonding
surface with your hands.
Do not re-attach the
O
Camera bracket
adhesive.
ꢁ
Mount the camera body onto the camera bracket.
Bolt with washer
Side view
The screw holes to use, and the possible angle
adjustment, vary according to the mounting
position.
Logo
Logo
0°
Direction
of forward
motion
Direction
of forward
motion
45°
Hexagon wrench
Rear view camera
90°
90°
Mount on the screw holes Mount on the screw holes
on the side opposite
the direction of forward
motion.
below the camera.
Side with logo
uppermost
ꢂ
Adjust the camera angle so that the fender or the rear edge of the vehicle
appears at the bottom of the monitor.
Camera field of view
Use the Hexagon wrench
to loosen the bolts, then
adjust the camera angle.
(After adjusting, tighten the
bolts securely.)
Approx. 103°
Fender or the rear edge of
the vehicle
Approx. 134°
Memorandum
|