Onkyo Universal Remote RC 391M User Manual

Using the remote controller  
Overview  
When you use a remote controller, typically you press one of the MODE buttons that corresponds to the device you wish to control, then  
press the operation buttons. For example, if you wish to control the TX-DS575 from a remote controller, first press the MODE AUDIO but-  
ton, then press an appropriate operation button. To control a CD player, press the MODE CD button, then press an appropriate operation but-  
ton.  
First, press the desired MODE button to make sure that the TX-DS575 is set to a correct mode.  
Using the RC-391M to control each device  
SEND  
Turning the power on and off to the TX-DS575  
indicator  
Note:  
Before operating the RC-391M, turn on the POWER switch on the  
TX-DS575 so that the unit enters standby mode.  
POWER ON  
MODE AUDIO  
POWER  
STNBY  
1. Press the MODE AUDIO button.  
2. Pressing the POWER ON buttons will switch between power on.  
Pressing the POWER STNBY button will power standby.  
SEND indicator  
This indicator acts as a guide when commands are programmed  
into or sent by the remote controller. It also warns the user when  
an error is made or battery power is low.  
Controlling the TX-DS575  
1. Press the MODE AUDIO button.  
2. Press the desired operation button.  
Shaded buttons in the figure are the operation buttons used to  
control the TX-DS575.  
POWER ON  
SLEEP  
SLEEP  
POWER ON/STNBY  
: Power on/standby  
: Sleep function  
POWER  
STNBY  
DISPLAY  
VOL q/u  
CH +/–  
: Changing the display  
: Adjusting the volume  
: Tuner preset number increment/decrement  
MODE  
AUDIO  
INPUT SELECTOR  
DISPLAY  
Listening mode (STEREO/DSP/DSP®/SURROUND)  
: Changing Listening mode  
SP A/SP B : Switching between Speakers A and B  
CH SEL  
DIMMER  
: Selecting a speaker  
: Adjusting the brightness of the display  
VOL  
CH +/–  
LEVEL +/– : Adjusting the speaker levels  
TEST  
TEST  
: Test tone  
: Muting  
MUTING  
MUTING  
INPUT  
SELECTOR  
Litening  
mode  
SP A/B  
LEVEL +/–  
CH SEL  
DIMMER  
31  
 
Using the remote controller  
Controlling an Onkyo MD recorder  
Note:  
Make sure that you point the transmission part on the remote con-  
troller toward the sensor area on the MD recorder.  
1. Press the MODE MD/AUX button.  
2. Press the desired MD operation button.  
MODE MD  
Turning the power on and off to the MD recorder  
POWER ON/STNBY  
: Turning on or standby the power to the MD  
recorder  
: Down  
: Up  
: Playback  
: Stop  
: Rewind  
: Fast forward  
MD  
operation  
buttons  
: Record  
: Pause  
REC  
EJECT  
1~9, +10  
ENT  
: Eject  
: Numeric keys  
: Confirm  
Numeric keys,  
ENT button  
You may also use the following buttons:  
VOL q/u  
: Adjusting the volume level of the TX-  
DS575  
MUTING  
: Muting the sound from the TX-DS575  
Controlling an Onkyo tape deck  
Note:  
First connect an Onkyo tape deck using the  
page 9.)  
connection. (See  
MODE  
AUDIO  
1. Press the MODE AUDIO/TAPE button.  
2. Press the desired tape deck operation button.  
: Playback  
: Stop  
: Rewind  
: Fast forward  
: Recording/pause  
: Reverse playback  
REC  
TAPE  
operation  
buttons  
You may also use the following buttons:  
VOL q/u  
: Adjusting the volume level of the TX-  
DS575  
MUTING  
: Muting the sound from the TX-DS575  
MODE SAT, CABLE, VCR, and TV buttons  
No preset codes are programmed into the MODE SAT, CABLE,  
VCR, and TV buttons. You can use these buttons to program  
remote controller signals of other devices. (See page 34.)  
You may use the following buttons:  
MODE SAT,  
CABLE, VCR,  
TV  
VOL q/u  
: Adjusting the volume level of the TX-  
DS575  
MUTING  
: Muting the sound from the TX-DS575  
33  
 
Programming the remote controller codes of  
other devices into the RC-391M  
The RC-391M has two learning functions. One is a normal learning function that enables the RC-391M to learn other remote controllers’  
codes. The other is a macro learning function, which enables the RC-391M to learn a series of codes already memorized in the remote con-  
troller into one MACRO button.  
Programming procedure  
Program the codes for each mode (AUDIO, CD, DVD, MD, SAT, CABLE, VCR, and TV).  
Light  
4
1
6
5 to 15 cm  
(2 to 6 inches)  
2
3
The button you wish to memorize  
RC-391M  
1. Place the RC-391M and the remote controller for another  
device, with 5–15cm (2–6 inches) apart and the light-emit-  
ting parts facing each other.  
Note:  
The remote controller has 408 memory slots (51 buttons × 8  
modes), although this number varies significantly depending on  
the manufacturers and types of the remote controller you wish to  
program into the RC-391M. It is recommended that you deter-  
mine which button functions have priority for programming.  
If you do not press any button for more than 30 seconds during  
the procedure, the SEND/LEARN indicator flashes three times  
quickly, then the RC-391M exits Learning mode. Resume Step 2.  
If you make a mistake during programming, the SEND/LEARN  
indicator flashes three times quickly, then the RC-391M exits  
Learning mode.  
2. While pressing and holding down the desired MODE button  
on the RC-391M (AUDIO, CD, DVD, MD, SAT, CABLE,  
VCR, or TV), press the ENT button, then release the but-  
tons.  
When you press and hold down one of the MODE button, the  
SEND/LEARN indicator lights up. When you press the ENT  
button, the indicator turns off. When you release the buttons, the  
SEND/LEARN indicator lights up again.  
If you try to program beyond the learning capacity of the RC-  
391M, the SEND/LEARN indicator flashes six times quickly,  
then the RC-391M exits Learning function. Try programming in  
a button of other MODE.  
3. Press and release the desired operation button on the RC-  
391M.  
You may select any button within the rectangle shown in the figure.  
When you press the button, the SEND/LEARN indicator turns off.  
When you release the button, the indicator lights up again.  
Follow the same procedure when you wish to program new  
codes into the already-programmed buttons.  
This remote controller uses infrared rays. Most remote control-  
ler codes can be memorized using the infrared system; however,  
depending on the degree to which the system differs, there may  
be some rare occasions when memorization is not possible.  
Some remote controllers use a single button to perform different  
functions, with the function code changing each time the button  
is pressed. If you are using this kind of controller, please per-  
form the “learn” operations for each function individually to  
store each function to a button on the RC-391M.  
4. Press and hold down the desired button on the remote con-  
troller of the other device until the SEND/LEARN indicator  
on the RC-391M flashes twice.  
The SEND/LEARN indicator flashes twice slowly, then lights up.  
5. Repeat Steps 3–4 to program other buttons in the same  
MODE.  
Repeat Steps 2-4 to program other buttons in a different MODE.  
6. Press the MODE button to complete programming.  
For instructions regarding the operation of “learned” units,  
7. Operate the programmed button to make sure the learning  
function works.  
please refer to the instruction manual for each product.  
Even after codes have been memorized, please keep your old  
remote controller in a safe place. If the memorized codes are  
lost when the batteries run down, it will be necessary to memo-  
rize them once again using the old remote controller.  
Make sure both the RC-391M and the product’s own remote  
controller have fresh batteries. If either of them has batteries  
that are wearing down, it may be impossible to store the remote  
controller codes into the RC-391M or the product may not  
respond properly to the buttons on the RC-391M for which the  
remote controller codes were stored into memory.  
Note:  
The remote controller codes for the Onkyo CD player, tape  
deck, DVD player, and MD recorder have already been pro-  
grammed into the buttons on the RC-391M. You may program  
other remote controller codes into these buttons. If you wish to  
restore the Onkyo preset codes after you program new codes,  
erase the new codes. (See page 35.)  
34  
 
Programming the remote controller codes of other devices into the RC-391M  
See page 39 for information on how to erase the learned codes from all buttons.  
Erasing a learned code  
SEND/LEARN  
You can erase a learned code. You cannot erase preset codes.  
indicator  
Erasing a code programmed in a button  
1. Press and hold down the corresponding MODE button and  
press the ENT button, then release the buttons.  
When you press the MODE button, the SEND/LEARN indica-  
tor lights up. When you press the ENT button, the indicator  
turns off. When you release the buttons, the indicator lights up  
again.  
MODE  
buttons  
2. Press and release the button from which you wish to erase  
the learned code.  
When you press the button, the SEND/LEARN indicator turns  
off. When you release the button, the indicator lights up again.  
3. Press and release the same button again.  
The SEND/LEARN indicator flashes twice slowly. The learned  
code is erased.  
Note:  
If you do not press the button in step 2 or 3 for more than 30 sec-  
onds, the SEND/LEARN indicator flashes three times quickly,  
then the RC-391M exits Learning mode. Resume Step 1.  
ENT  
Erasing a learned code from a MODE button  
SEND/LEARN  
indicator  
1. Press and hold down the MODE button from which you  
wish to erase the learned code, and press the ENT button  
twice. Then release the buttons.  
When you press the MODE button, the SEND/LEARN indica-  
tor lights up. When you press the ENT button, the indicator  
turns off. When you release the buttons, the indicator flashes  
twice slowly, then lights up again.  
MODE  
2. Press and release the same MODE button again.  
When you release the button, the SEND/LEARN indicator  
flashes twice slowly. The learned code is erased.  
buttons  
Note:  
If you do not press any button for more than 30 seconds, the  
SEND/LEARN indicator flashes three times quickly, then the  
RC-391M exits Learning mode. Resume Step 1.  
If you make a mistake during programming, the SEND/LEARN  
indicator flashes three times quickly, the RC-391M exits Learn-  
ing mode. Resume Step 1.  
If have programmed many button operations to a single MODE  
button, the SEND/LEARN indicator may remain illuminated  
continuously in Step 2. This is not malfunction.  
ENT  
35  
 
Using a Macro function  
What is a Macro function?  
A Macro function enables you to program a series of button operations on the remote controller into a single button. For example, you need  
to follow the steps below to play a CD player connected to the TX-DS575 without using the Macro function:  
1: Press the MODE AUDIO button. 2: Press the POWER ON button. 3: Press the CD (INPUT SELECTOR) button. 4: Press the  
MODE CD button. 5: Use the numeric keys to select the desired song.  
This operation will be two button presses away if you program these steps into a macro button.  
Programming Macro mode  
You may program the desired steps into each of eight MODE but-  
tons. The following example explains how to program Steps 1–5  
(described above) into the MACRO MODE button under the  
MODE CD button (CD mode).  
1. Press and hold down the desired MODE button you wish to  
2
program (in this case, MODE CD button), and press the  
MACRO MODE button. Then release the buttons.  
When you press the MODE CD button, the SEND/LEARN  
indicator lights up. When you press the MACRO MODE button,  
the indicator turns off.  
When you release the buttons, the indicator flashes briefly, then  
lights up again.  
1, 2  
2
1, 3  
2. Press the operation buttons in series you wish to program  
into the MACRO MODE button.  
Press the MODE AUDIO, POWER ON, CD (INPUT SELEC-  
TOR), MODE CD buttons, and a numeric key. When you press  
the button, the SEND/LEARN indicator turns off. When you  
release the button, the indicator lights up.  
3. Press the MACRO MODE button to complete program-  
ming.  
The SEND/LEARN indicator flashes twice slowly.  
Repeat Steps 1–3 to program other series of button operations  
into another MODE button.  
4. Check to see if the series of button operation has been cor-  
rectly learned.  
2
2
Point the remote controller toward the TX-DS575, press the  
MODE CD button, and press the MACRO MODE button to see  
if the unit responds as programmed.  
Transmitting the codes in Macro mode takes a while. During  
transmission, point the remote controller toward the device to  
be controlled.  
Note:  
You may program up to 16 button operations into each MACRO  
button. If you try to program the 17th step, it will be ignored.  
If you do not press any button for more than 30 seconds during  
the procedure, the SEND/LEARN indicator flashes three times  
quickly, then the RC-391M exits Learning mode. Resume Step  
1.  
If you make a mistake during programming, the SEND/LEARN  
indicator flashes three times quickly, then the RC-391M exits  
Learning mode. Resume Step 1.  
If you erase one of the operation buttons already programmed in  
the MACRO MODE button, or if you program a different code  
into such a button, the operation button will no longer work. In  
this case, program the buttons again to avoid malfunction.  
Tip:  
The codes programmed into a MACRO button will be  
transmitted with an interval of 0.5 seconds. However,  
some devices may not be able to complete one opera-  
tion in 0.5 seconds and may miss the next code. In this  
case, press one operation button, press the correspond-  
ing MODE button, then press another operation button  
to extend the interval between the two operations up to  
one second.  
36  
 
Using a Macro function  
Macro Direct Learning function  
A series of remote controller button operations can be memorized  
into the MACRO DIRECT button for one-touch control.  
Note:  
You can program only one series of button operations into the  
MACRO DIRECT button.  
1. Press and hold down any one of the eight MODE buttons  
and press the MACRO DIRECT button. Then, release the  
buttons.  
1, 3  
1
When you press the MODE button, the SEND/LEARN indica-  
tor lights up. When you press the MACRO DIRECT button, the  
indicator turns off. When you release the buttons, the indicator  
flashes briefly, then lights up again.  
2. Follow Steps 2 in the “Programming Macro Mode” on page  
36.  
3. Press the MACRO DIRECT button to complete the proce-  
dure.  
The SEND/LEARN indicator flashes twice slowly.  
4. Check to see if the button has been programmed correctly.  
Point the RC-391M toward the TX-DS575 and press the  
MACRO DIRECT button, and make sure that the device  
responds as programmed.  
Transmitting the codes in Macro mode takes a while. During  
transmission, point the remote controller toward the device to  
be controlled.  
Note:  
You may program up to 16 button operations into the MACRO  
DIRECT button. If you try to program the 17th step, it will be  
ignored.  
If you do not press any button for more than 30 seconds during  
the procedure, the SEND/LEARN indicator flashes three times  
quickly, then the RC-391M exits Learning mode. Resume Step  
1.  
If you make a mistake during programming, the SEND/LEARN  
indicator flashes three times quickly, then the RC-391M exits  
Learning mode. Resume Step 1.  
If you erase one of the operation buttons already programmed in  
the MACRO MODE button, or if you program a different code  
into such a button, the operation button will no longer work. In  
this case, program the buttons again to avoid malfunction.  
Tip:  
The codes programmed into a MACRO button will be  
transmitted with an interval of 0.5 seconds. However,  
some devices may not be able to complete one opera-  
tion in 0.5 seconds and may miss the next code. In this  
case, press one operation button, press the correspond-  
ing MODE button, then press another operation button  
to extend the interval between the two operations up to  
one second.  
37  
 
Using a Macro function  
Erasing a learned remote controller button oper-  
ation from the MACRO MODE buttons  
1. Press and hold down the corresponding MODE button and  
press the MACRO MODE button, then release the buttons.  
When you press the MODE button, the SEND/LEARN indica-  
tor lights up. When you press the MACRO MODE button, the  
indicator turns off. When you release the buttons, the indicator  
flashes once.  
1, 2  
1
2. Press the MACRO MODE button again.  
The SEND/LEARN indicator flashes twice slowly. The learned  
operation is erased.  
Erasing a learned remote controller button oper-  
ation from the MACRO DIRECT button  
1. Press and hold down any one of the MODE buttons and  
press the MACRO DIRECT button. Then release the but-  
tons.  
When you press the MODE button, the SEND/LEARN indica-  
tor lights up. When you press the MACRO DIRECT button, the  
indicator turns off. When you release the buttons, the indicator  
flashes once.  
1, 2  
1
2. Press the MACRO DIRECT button again.  
The SEND/LEARN indicator flashes twice slowly. The learned  
operation is erased.  
Note:  
If you do not press any button for more than 30 seconds, the  
SEND/LEARN indicator flashes three times quickly, then the  
RC-391M exits Learning mode. Resume Step 1.  
If you press a wrong button in Step 2, you may have overwritten  
the memory of the button you pressed.  
38  
 
Using a Macro function  
Erasing all codes and operations programmed  
in the buttons  
This procedure will erase all remote controller codes for the other  
devices and all macro operations that have been programmed in the  
RC-391M (see pages 34, 36 and 37).  
2
1. Open the battery cover and remove the batteries.  
2. While pressing and holding down the POWER ON button  
and the POWER STNBY button, insert the batteries in the  
correct direction.  
After inserting the batteries, release the buttons. The SEND/  
LEARN indicator flashes slowly.  
3. Press the ENT button.  
The SEND/LEARN indicator lights up for about ten seconds,  
then turns off. All programmed codes are erased and the button  
memories return to the factory presets.  
Note:  
Proceed to Step 3 immediately after Step 2. Otherwise, the bat-  
teries will be consumed quickly.  
If you press any button other than the ENT button in Step 3, no  
codes will be erased. In this case, repeat the steps from the  
beginning.  
3
39  
 

Miele Cooktop KM453 User Manual
Miller Electric Welding System Regency 250 User Manual
Milwaukee Drill 1670 1 User Manual
MTD Log Splitter 249 623 003 User Manual
NEC Water System N 1093100 User Manual
NETGEAR Switch FS605 v2 User Manual
Omega Engineering Stud Sensor CDE681 User Manual
Opticon Scanner CRD972X User Manual
Panasonic Flat Panel Television BT LH2600WMC User Manual
Patriot Products Blower T4 CBV User Manual