K-79
Dialtemp™ Thermometer
INSTRUCTION
SHEET
M0299/0802
SECTION 1 INTRODUCTION
®
The OMEGA Model K-79 Series Pocket Thermometer is a small,
mechanical (non-electronic) thermometer that is accurate, rugged and light
in weight. The clear, easy to read 1" dial has a pointer that is directly driven
by the sensitive bi-metal helix coil located in the shaft. The 0.142" diameter,
5" stainless steel probe has a needle tip for penetrating semi-solid materials
such as fruits and meats. The pointed probe is supplied with a tubular
pocket case complete with a pocket clip and holder loop. (See Figure 1)
LOOP HOLDER
POCKET CLIP
POCKET CASE
DIALTEMP
Figure 1 K-79 Thermometer with Pocket Case
slowly and carefully to avoid bending. Do not hold the head when
inserting, always hold the stem.
CAUTION
Do not place a "Dial Temp" thermometer in contact with a
material where electrical voltage potential is present.
SECTION 4 CALIBRATION
OMEGA K-79 Series Pocket Thermometers are factory calibrated. The
alloys used in the bi-metal element determine the span calibration and
are not adjustable. The dial head itself, however, can be reset. This is
done at ambient temperature, where the pointer remains stable, and the
dial is adjusted.
To reset the dial:
1. Determine the room temperature by using a reference thermometer
of known accuracy.
2. Firmly hold the hex nut at the base of the dial with a 7/16” wrench.
3. With your other hand, firmly grip the perimeter of the dial. Slowly
turn the dial head until the reading corresponds to room the
temperature.
SECTION 5 SPECIFICATIONS
Accuracy:
1% of scale
Approx. Response Time
in Water:
4 seconds for one time constant*
1" diameter (25 mm)
Head:
Dial:
White background with crisp letters, marks
and numbers
Stem:
.142 O.D., 5" long, pointed (3.6 mm x 127 mm)
7/16" hex (11 mm)
Reset Nut:
Pocket Case:
Weight:
Stainless steel with clip and holder loop
.65 ounces (18.5 g)
* “Time Constant” is the time required to reach 63.2% of instantaneous
temperature change.
Servicing Europe:
Benelux:
Postbus 8034, 1180 LA Amstelveen, The Netherlands
Tel: +31 (0)20 3472121
FAX: +31 (0)20 6434643
OMEGAnet® Online Service
Internet e-mail
Toll Free in Benelux: 0800 0993344
e-mail: [email protected]
Czech
Rudé armády 1868, 733 01 Karviná 8
Servicing North America:
Republic:
Tel: +420 (0)69 6311899
Toll Free: 0800-1-66342
FAX: +420 (0)69 6311114
e-mail: [email protected]
USA:
ISO 9001 Certified
One Omega Drive, Box 4047
Stamford CT 06907-0047
Tel: (203) 359-1660
France:
11, rue Jacques Cartier, 78280 Guyancourt, France
Tel: +33 (0)1 61 37 29 00 FAX: +33 (0)1 30 57 54 27
Toll Free in France: 0800 466 342
e-mail: [email protected]
FAX: (203) 359-7700
e-mail: [email protected]
Canada:
976 Bergar
Laval (Quebec) H7L 5A1
Tel: (514) 856-6928
e-mail: [email protected]
Germany/
Austria:
Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
FAX: (514) 856-6886
Tel: +49 (0)7056 9398-0
FAX: +49 (0)7056 9398-29
Toll Free in Germany: 0800 639 7678
e-mail: [email protected]
For immediate technical or application assistance:
®
United
One Omega Drive, River Bend Technology Centre
Northbank, Irlam, Manchester
USA and
Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA
Customer Service: 1-800-622-2378 / 1-800-622-BEST
®
Kingdom:
Canada:
®
ISO 9002 Certified M44 5BD United Kingdom
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
Tel: +44 (0)161 777 6611
FAX: +44 (0)161 777 6622
Toll Free in United Kingdom: 0800-488-488
e-mail: [email protected]
Mexico:
En Espan˜ol: (001) 203-359-7803
FAX: (001) 203-359-7807
e-mail:[email protected]
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of its
products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to alter
specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient-connected applications.
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from
date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each
product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be
defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the
purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or
unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of
having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification;
misapplication; misuse or other operating conditions outside of OMEGA’s control. Components which wear are not warranted,
including but not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility
for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with
information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by it will be as
specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND
WHATSOEVER, EXPRESS OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION
OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with respect to this
order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the
purchase price of the component upon which liability is based. In no event shall OMEGA be liable for consequential,
incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR
21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s)
be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes
no responsibility as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and
hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please have the following informa-
tion available BEFORE contacting OMEGA:
1. Purchase Order number under which the product was
PURCHASED,
2. Model and serial number of the product under warranty, and
FOR NON-WARRANTY REPAIRS, consult OMEGA for cur-
rent repair charges. Have the following information avail-
able BEFORE contacting OMEGA:
1. Purchase Order number to cover the COST of the repair,
2. Model and serial number of the product, and
3. Repair instructions and/or specific problems relative to the
product.
3. Repair instructions and/or specific problems relative to
the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in
technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2002 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or
reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING,
INC.
M0299/0802
|