Omega Vehicle Security Computer Monitor DPiTH i8DH User Manual

OPERATION  
Step 17. Enter Alarm 1 Enable/Disable Submenu  
Press to display flashing  
SPECIFICATION  
/
DSBL ENBL  
.
d
Output 1:  
Step 1. Apply Power to the Instrument  
When your device is first powered up it will display the  
ambient temperature (assume 75°F).  
SENSOR SPECIFICATIONS  
Relative Humidity Accuracy/Range:  
2% for 10 to 90% RH  
3% for 0 to 10%RH and 90 to 100%RH  
Non-linearity: 3%  
Hysteresis: 1% RH  
Response Time:  
4 sec (63% slowly moving air)  
Relay 250 Vac @ 3 AResistive Load,  
SSR, Pulse  
Step 18. Enable Alarm 1 Submenu  
If flashing is displayed, press , if  
is displayed,  
Output 2:  
ENBL  
a
DSBL  
is displayed, then press to store and  
Relay 250 Vac @ 3 AResistive Load,  
press until  
b
ENBL  
d
Step 2. Enter Setpoint 1 Menu  
SSR, Pulse  
go to the next menu item.  
Only with -AL Limit Alarm option  
Press one time from run mode to get to  
Setpoint 1.  
SP1  
a
Options: Communication  
RS-232 / RS-485 or 10BaseT  
Step 19. Select the Deviation Control Type Submenu  
Step 3. Enter the Setpoint 1 Value Submenu  
Repeatability: 0.1%  
Resolution: 0.03%, 12bit  
or Excitation: 24 Vdc @ 25 mA  
Press . If flashing  
Deviation is displayed press  
,
a
d
_DEV  
Press . Display shows the previous selection of Setpoint 1.  
d
Exc. not available for Low Power Option  
otherwise press until flashing  
is shown. Now  
_DEV  
b
Line Voltage/Power:  
90 - 240 Vac 10%, 50 - 400 Hz*,  
Temperature Accuracy/Range*:  
1°C ( 2°F) for -40 to 0°C and 80 to  
123.8°C (-40 to 32°F and 176 to 254°F)  
press to store and go to next menu item.  
d
Step 4. Change the Setpoint 1 Value  
or 110 - 375 Vdc, 5 W  
Press or until desired value is displayed.  
b
c
Step 20. Select the Latched Type Submenu  
* No CE compliance above 60 Hz  
0.5°C ( 1°F) for 0 to 80°C (32 to 176°F)  
Low Voltage Power Option:  
Press . If flashing  
Unlatched is displayed press  
,
a
d
UNLT  
*NOTE: extended temp range is for Probe only, the  
Controller’s operating temp is 0-50°C  
12 - 36 Vdc, 3 W**  
Step 5. Store the Setpoint 1 Value  
otherwise press until  
is displayed.  
b
UNLT  
** Units can be powered safely with 24 Vac  
but No Certification for CE/UL are claimed.  
Set the Setpoint 1 to 10 degree higher than Process value  
Repeatability: 0.1°C  
Resolution: 0.01°C, 14 bit  
Press to store and advance to next menu item.  
d
(SP1 = 85) and press to store, display flashes  
d
STRD  
Setpoint 2 Menu.  
Dimensions:  
Dual Horizontal: 48H x 96W x 127D mm  
(1.89 x 3.78 x 5")  
Dual Vertical: 48W x 96H x 127D mm  
(1.89 x 3.78 x 5")  
Weight:  
295 g (0.65 lb)  
Approvals:  
CE per EN61010-1:2001  
Step 21. Select the Normally Open Type of Contact  
Closure Submenu  
message and advances to  
SP2  
METER SPECIFICATIONS  
Display:  
4-digit, 9-segment LED,  
• 10.2 mm (0.40"): DPiTH-i8DV Dual Vertical  
• 10.2 mm (0.40") and 21 mm (0.83"):  
DPiTH-i8DH Dual Horizontal  
Red, green, and amber programmable  
colors for setpoint and temperature units.  
Press . If flashing  
Normally Open is displayed,  
N.o.  
d
Step 6. Store the Setpoint 2 Value  
press , otherwise press until  
is displayed. Press  
a
b
N.o.  
d
Repeat steps 3 and 4. Set the Setpoint 2 to 5 degree higher  
than Process value (SP2 = 80) and press to store,  
MADE IN  
to store and advance to next menu item.  
d
USA  
display flashes  
STRD  
Configuration Menu.  
message and advances to  
CNFG  
Step 22. Select the Above Type of Active Submenu  
Press . If flashing  
Above is displayed, press a,  
ABoV  
d
otherwise press b until  
is displayed. Press d to store  
ABoV  
Step 7. Enter the Reading Config Menu  
Press to enter Reading Config Menu.  
and advance to next menu item.  
DPiTH-i8DH, DPiTH-i8DV  
d
RDG  
WARNING: These products are not designed for use in, and should not be used for, patient-  
connected applications.  
Humidity + Temperature Monitor  
(
)
Step 23. Enable Alarm 1 at Power On  
A.P.oN  
Step 8. Enter the submenu items of Rdg Config Menu  
This device is marked with the international caution symbol. It is important to read the  
Setup Guide before installing or commissioning this device, as the guide contains important  
information relating to safety and EMC.  
Press d. If flashing  
is displayed, press , otherwise  
ENBL  
a
CNiTH-i8DH-AL, CNiTH-i8DV-AL  
Press to display Sensor submenu: Sensor selection  
d
SNSR  
for Autotune, Loop, or Ramp and Soak  
press until  
is displayed. Press to store and  
b
ENBL  
d
is for  
°F.°C  
advance to next menu item.  
Humidity + Temperature Limit Alarm  
It is the policy of OMEGAto comply with all worldwide safety and EMC/EMI regulations that apply.  
OEMGAis constantly pursuing certification of its products to the European New Approach Directives.  
OMEGAwill add the CE mark to every appropriate device upon certification.  
The information contained in this document is believed to be correct, but OMEGAEngineering, Inc.  
accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.  
temperature and  
is for Humidity  
DRRh  
Step 24. Enter Alarm 1 High Submenu  
Press twice to skip  
Alarm 1 Low value.  
is  
ALR.L  
a
ALR.L  
for above.  
Step 9. Enter the submenu items of Rdg Config Menu  
®
for below &  
ALR.H  
Press to display Temp Unit submenu:  
d
TRADEMARK NOTICE:  
®
®
(
)
Step 25. Set the Alarm 1 High value  
®
ALR.H  
Press d. Press or until value to set the display to  
®
,
omega.com  
,
,
and  
are Trademarks of  
®
Step 10 Scroll thru selection for Temp Unit submenu  
b
c
Press to Scroll though the available selections of the  
b
OMEGAENGINEERING, INC.  
. Press to save.  
002.0  
d
Temperature Unit of your choice:  
or .  
°F °C  
OMEGAnet® On-Line Service  
Internet e-mail  
Step 26. Enter the Alarm 2 Menu  
Step 11. Store the Temperature Unit  
The display will show  
the top menu for Alarm 2.  
Repeat steps from 17 to 25 to set for Alarm 2 the same  
ALR2  
WARRANTY/DISCLAIMER  
OMEGAENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for  
one (1) year from the date of purchase. In addition to OMEGA’s standard warranty period, OMEGA Engineering will  
extend the warranty period for four (4) additional years if the warranty card enclosed with each instrument is  
returned to OMEGA.  
Press , display momentarily shows  
the Unit has  
d
STRD  
a
period of  
been stored and the instrument will go automatically to the  
next menu item.  
conditions as for Alarm 1.  
Servicing North America:  
Step 29. Configuration of Display Color Selection  
USA:  
One Omega Drive, P.O. Box 4047  
Stamford CT 06907-0047  
TEL: (203) 359-1660  
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will  
issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA,  
if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply  
to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing,  
operation outside of design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit  
shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive  
corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating  
conditions outside of OMEGA’s control. Components which wear are not warranted, including but not limited to  
contact points, fuses, and triacs.  
ISO 9001 Certified  
Press until the  
Display Color Selection Menu  
COLR  
a
Step 12. Enter the Filter Constant Submenu  
FAX: (203) 359-7700  
FAX: (514) 856-6886  
appears on the Display. Configure  
as  
/
COLR  
N.CLR GRN  
(amber). Please  
2.CLR AMBR  
Display shows  
Filter Constant Submenu.  
FLTR  
(green),  
/
(red),  
/
1.CLR RED  
refer to the operator’s manual if needed.  
Canada:  
976 Bergar  
Step 13. Display the Filter Constant Value Submenu  
Laval (Quebec) H7L 5A1  
TEL: (514) 856-6928  
Press to display the flashing, previously selected Filter  
d
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither  
assumes responsibility for any omissions or errors nor assumes liability for any damages that result from  
the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA  
warrants only that the parts manufactured by it will be as specified and free of defects. OMEGA MAKES NO  
OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED,  
EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION  
OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with  
respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or  
otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event  
shall OMEGA be liable for consequential, incidental or special damages.  
For color change on Setpoints refer to Owners Manual  
Section 2.  
Constant.  
For immediate technical or application assistance:  
Step 14. Scroll through available Filter Constants  
USA and Canada:  
Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA®  
Customer Service: 1-800-622-2378 / 1-800-622-BEST®  
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN®  
Press to sequence thru Filter Constants  
,
0001 0002  
,
b
,
,
,
,
0004 0008 0016 0032 0064  
and  
.
0128  
CONDITIONS:  
Equipment sold by OMEGAis not intended to be used, nor shall it be used: (1) as  
a
“Basic  
TEL: (001)800-TC-OMEGA®  
En Español: (001) 203-359-7803  
FAX: (001) 203-359-7807  
Step 15. Store the Filter Constant  
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications  
or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application,  
Mexico and  
Press momentarily to store  
Filter Constant and the  
d
0004  
used on humans, or misused in any way, OMEGAassumes no responsibility as set forth in our basicLatin American:  
WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless  
from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.  
instrument will automatically go to the next menu item.  
RETURN REQUESTS/INQUIRIES  
Servicing Europe:  
Step 16. Enter Alarm 1 Menu  
Direct all warranty and repair requests/inquiries to the OMEGACustomer Service Department. BEFORE  
RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR)  
Benelux:  
Postbus 8034, 1180 LA Amstelveen, The Netherlands  
TEL: +31 20 3472121  
Toll Free in Benelux: 0800 0993344  
The display will show  
the top menu for Alarm 1. In the  
ALR1  
NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING  
DELAYS). The assigned AR number should then be marked on the outside of the return package and on any  
correspondence.  
FAX: +31 20 6434643  
following steps we are going to enable Alarm 1, Deviation,  
Unlatch, Normally Open, Active Above, Enable at power-on  
and +2°F High Alarm i.e. Process Value > Setpoint 1 Value  
+2°F will activate Alarm 1.  
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in  
transit.  
FOR WARRANTY RETURNS, please have the  
Czech Republic:  
Frystatska 184, 733 01 Karviná  
TEL: +420 59 6311899  
FOR NON-WARRANTY REPAIRS, consult OMEGA for  
current repair charges. Have the following information  
following information available BEFORE  
FAX: +420 59 6311114  
contacting OMEGA:  
available BEFORE contacting OMEGA:  
1. Purchase Order number under which the product  
was PURCHASED,  
2. Model and serial number of the product under  
warranty, and  
3. Repair instructions and/or specific problems  
relative to the product.  
1. Purchase Order number to cover the COST of the  
repair,  
2. Model and serial number of product, and  
3. Repair instructions and/or specific problems  
relative to the product.  
• If Analog Output Option is installed and enabled,  
the controller will skip Alarm 1 Menu item to Analog  
Output.  
• Alarm must be DISABLED if Ramp is ENABLED.  
• Alarm1 will only work for Humidity, not  
Temperature.  
France:  
11, rue Jacques Cartier, 78280 Guyancourt  
TEL: +33 1 61 37 29 00 FAX: +33 1 30 57 54 27  
Toll Free in France: 0800 466 342  
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords  
our customers the latest in technology and engineering.  
Germany/Austria:  
Daimlerstrasse 26, D-75392 Deckenpfronn, Germany  
TEL: +49 7056 9398-0  
Toll Free in Germany: 0800 639 7678  
FAX: +49 7056 9398-29  
OMEGAis  
a
registered trademark of OMEGAENGINEERING, INC.  
© Copyright 2005 OMEGAENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,  
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without  
the prior written consent of OMEGAENGINEERING, INC.  
United Kingdom:  
ISO 9002 Certified  
One Omega Drive  
River Bend Technology Centre  
Northbank, Irlam Manchester M44 5BD United Kingdom  
TEL: +44 161 777 6611 FAX: +44 161 777 6622  
Toll Free in England: 0800 488 488  
Alarm 1 is designed to monitor the humidity value  
around Setpoint 1 and Alarm 2 is designed to monitor  
the temperature value around Setpoint 2.  
PATENT AND TRADEMARK NOTICE: This product is covered by one or more of the following patents: U.S. Pat.  
No. Des. 336,895; 5,274,577; 6,243,021 / CANADA 2052599; 2052600 / ITALY 1249456; 1250938 / GERMANY DE  
41 34398 C2 / SPAIN 2039150; 2048066 / UK Patent No. GB2 249 837; GB2 248 954 / FRANCE BREVET NO. 91  
12756. The “Meter Bezel Design” is a trademark of Newport Electronics, Inc. USED UNDER LICENSE. Other U.S.  
and International Patents pending or applied for.  
MQS4003/1105  
 

Miele Kitchen Utensil G 6XX User Manual
Multi Tech Systems Network Card MT5634ZPX PCI U NV User Manual
Napoleon Fireplaces Stove 1600C 1 User Manual
Nintendo Video Game Controller MAA RVL A WR USZ C0 User Manual
Oreck Vacuum Cleaner DS1700HY User Manual
Panasonic Answering Machine KX TG8162AL User Manual
Panasonic Electric Shaver EW1000 User Manual
Panasonic Network Card MAZC062D User Manual
Panasonic Portable CD Player KXL 783M User Manual
Panasonic Stereo System SC AK340 User Manual