BES100_200_QuickInstallGuide4.pdPage 1
8/24/2006
2:44:38 PM
8. Connect the AC power cord to the back of the switch, and
then connect the cord to an AC power outlet.
8
Busin
Quick Install Guide
B
ess
E
Eth
S
ern
1
et S
0
wit
0
ch/
1
2
00/2
0
000Series
Steps 8 9
Powering Up
AC LINE
100-240 VAC
50-60 Hz
xxx
A
MAX
100
200
3. Check your cables; when you install the switch into a
network, make sure you use the following required cables:
• Category 3, 4, or 5 UTP cable with an RJ-45 connector (for
100 Mb/s operation).
• Category 5 UTP cable with an RJ-45 connector (for 100 Mb/s
operation). The stacking cable for the BES 200 is a CAT5
Ethernet cable.
• Category 5 Four-Pair UTP cable with an RJ-45 connector (for
1000 BASE-T ports with 1000 Mb/s operation).
• Console Port Straight-through serial cable with DB-9 female
connector at one end.
AC LINE
100-240 VAC
50-60 Hz
Cascade Down Cascade Up
2.9
A
MAX
Base
Unit Select
All documents referenced in this Quick
Installation Guide can be downloaded at
Warning:You must use a line cord set approved for the
receptacle type in your country.
3
9
9. Check the
front-panel LEDs as
the device powers
on to be sure the
Speed
Link/Act
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
Steps 1 3
25
26
Status
PWR
100
Before you
Reset
PoE
PoE
PWR LED is lit. If
not, check that the
power cable is
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
31
33
35
38
40
42
44
46
48
Speed
Link/Act
PoE
Link/Act
BES 220-24T-PWR
start
1
3
5
7
9
11
13
15
17
19
21
23
25
26
Up
Down
Base
Spe
L
i
n
k
e
d
25
/Act
Stat
26
us
PW
R
Res
et
1
Status
200
3
5
7
PoE
PWR
9
11
4
6
13
Reset
8
15
correctly plugged in.
10
17
Steps 4 7
12
19
PoE
Console
2
4
6
8
10
12
14
16
18
20
22
24
21
14
23
16
18
25
20
27
22
29
24
31
33
26
35
28
30
37
31
39
33
41
35
43
45
38
14
47
40
Mounting Options
42
44
46
48
1
The BES100 and BES200 series switches begin switching data as soon as you
attach network devices and connect the switch to the power supply.
14. From the list of network
elements on the Element
Manager tree, select the
BES device.
1. Confirm that you have the tools and package
contents as follows:
4
With the BES200 series switch, traffic is switched across all units in the stack and
uses the 2 GBytes (gigabyte) of bandwidth across the stack connections as if it
were one switch.
Tools Required:
a. Phillips #2 screwdriver
Package Contents:
4. If you are mounting the switch on
a table or shelf, attach the rubber
feet to the device as indicated.
15. Click the Web Page
button on the Element
Manager menu.
C
M
c
15
InSitteipasl10Ac1c6ess and
Configuration
d
e
b
Y
5. Set the device on a flat surface near an AC
Spee
d
Link/A
ct
2
5
CM
MY
CY
CMY
K
2
6
power source, making sure there are at least 2
inches (5.1 cm) of space on all sides for proper
air flow and at least 5 inches (12.7 cm) at the
back for power cord clearance.
1
3
Statu
5
s
PWR
7
9
Reset
11
13
15
5
17
P
oE
19
2
21
4
23
6
25
8
27
10
29
12
31
14
33
16
35
18
37
20
39
22
41
24
43
26
45
28
47
30
31
33
35
38
40
16
42
44
46
48
10
b. BES100 or BES200 series Switch
c. Rack-mounting hardware
• Rack-mount brackets (2)
10. To access the BES100 or BES200, first
install the Business Element Manager 1.0.
Refer to Element Manager documentation at
16. From the main menu,
choose Administration >
Quick Start.
• Screws for attaching brackets to the
switch (8)
• Screws for attaching the switch to the
equipment rack (2x4)
Choose the appropriate set of rack-mount
screws for attaching the switch to your
data or phone rack.
6
The Quick Start screen
appears. It shows the IP
address and other items
that can be optionally
configured.
6. If you are mounting the
switch on a rack, attach the
brackets to each side of the
device using the screws
provided.
Speed
Link
/Act
2
5
2
6
1
Stat
us
PWR
3
5
Rese
t
7
9
11
PoE
13
2
15
4
17
6
19
8
21
10
23
12
25
11. Start the Element Manager.
14
27
16
29
18
31
20
33
22
35
24
37
26
39
28
41
30
43
31
45
33
47
35
38
40
42
11
44
46
48
d. Adhesive foot pads (4)
e. AC power cord
12. From the Element Manager menu,
If you want to manually
assign IP addresses,
refer to the Business
Ethernet Switch 100/200
Series User Guide on
a. Slide the switch into the
rack. Insert and tighten the
rack-mount screws.
choose Network > Find Network
12
Elements > Business Ethernet Switch.
Spe
Act
ed
Link/
2
5
2
6
1
Sta
tus
3
PW
R
5
Rese
t
7
9
11
PoE
13
2
15
4
17
6
19
8
21
10
23
12
25
14
27
16
29
18
31
20
33
22
35
24
37
26
39
28
41
30
43
31
45
33
47
35
38
40
42
44
46
48
2
2. (Optional) Prepare the rack:
13
a. Provide a 2.8 inch space for each switch
in an EIA or IEC-standard 19-inch
(48.2-centimeter) equipment rack.
b. Bolt the rack to the floor and brace it if
necessary.
13. Enter the range
192.168.1.1 to
You are now ready to use the BES100 or
BES200 series switch in your network
installation.
7
7. If you are stacking the BES200 switches, the fixed, dedicated
192.168.1.255, and
then click OK.
1000BASE-T ports on the rear panel of the units can stack up to four BES
200 series switches. These fixed ports allow you to configure and manage
the switches as a single switch and control the flow of network traffic. The
cable connections need to cross over in the BES200 units so that the UP
port connects to the Down port of the next unit, and vice versa.
c. Ground the rack to the same grounding
electrode used by the power service in the
area. The ground path must be permanent
and must not exceed 1 Ohm of resistance
from the rack to the grounding electrode.
Nortel recommends using a filter or surge
suppressor.
Refer to Using the Nortel Business Ethernet
Switch 100/200 at www.nortel.com for detailed
installation instructions.
N0131605
|