Meridian 1
ISDN Basic Rate Interface
Installation
Document Number: 553-3901-200
Document Release: Standard 7.00
Date: January 2002
Year Publish FCC TM
Copyright © 1992–2002 Nortel Networks
All Rights Reserved
Printed in Canada
Information is subject to change without notice. Nortel Networks reserves the right to make changes in design
or components as progress in engineering and manufacturing may warrant. This equipment has been tested
and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules, and the
radio interference regulations of Industry Canada. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at their own expense.
SL-1 and Meridian 1 are trademark of Nortel Networks.
4
Page 3 of 46
Revision history
January 2002
Standard 7.00. This document is up-issued to to include content changes for
Meridian 1 Release 25.40.
April 2000
Standard 6.00. This is a global document and is up-issued for X11 Release
25.0x. Document changes include removal of: redundant content; references
to equipment types except Options 11C, 51C, 61C, and 81C; and references
to previous software releases.
October 1997
August 1996
December 1995
Issue 5.00 released as Standard for Generic X11 Release 23.00
Issue 4.00 released as Standard for Generic X11 Release 22.0x.
Issue 3.00 released as Standard for Generic X11 Release 21.1x.
Note: No issue 2.00 was published.
December 1994
July 1994
Issue 1.00 released as Standard for Generic X11 Release 20.00
Standard version released for Generic X11 Release 19.00
Standard version released for Generic X11 Release 18.00
July 1993
ISDN Basic Rate Interface Installation
Page 4 of 46
553-3901-200 Standard 7.00 January 2002
6
Page 5 of 46
Contents
About this document . . . . . . . . . . . . . . . . . . . . . . .
Preinstallation preparation . . . . . . . . . . . . . . . . . . .
7
9
Install ISDN BRI hardware . . . . . . . . . . . . . . . . . . . 13
ISDN Basic Rate Interface Installation
Page 6 of 46
Contents
553-3901-200 Standard 7.00 January 2002
8
Page 7 of 46
About this document
This document applies to Meridian 1 Internet Enabled systems.
This document is a global document. Contact your system supplier or your
Nortel Networks representative to verify that the hardware and software
described is supported in your area.
Note 1: For Option 11C specific information, refer to Option 11C Basic
Rate Interface (BRI) (553-3011-311).
Note 2: ISDN BRI trunking is not available in North America.
ISDN Basic Rate Interface Installation
Page 8 of 46
About this document
553-3901-200 Standard 7.00 January 2002
12
Page 9 of 46
Preinstallation preparation
Contents
The following are the topics in this section:
Prepare the site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpack and inspect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Take inventory . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
10
11
Reference list
The following are the references in this section:
•
•
•
•
•
Installation Planning (553-3001-120)
System Engineering (553-3001-151)
Power Engineering (553-3001-152)
System Installation Procedures (553-3001-210)
ISDN Basic Rate Interface: Product Description (553-3901-100)
Prepare the site
When installing a system, address the following factors.
•
•
•
environmental
structural
electrical
Refer to the following documents for more information.
Installation Planning (553-3001-120)
•
ISDN Basic Rate Interface Installation
Page 10 of 46
Preinstallation preparation
•
•
System Engineering (553-3001-151)
Power Engineering (553-3001-152)
After the site has been planned, the following items must be completed prior
to ISDN BRI installation.
•
Wire the building between ISDN BRI terminal locations and the
distribution frame. Refer to the “Engineering guidelines” section of
ISDN Basic Rate Interface: Product Description (553-3901-100) for
wiring specifications and guidelines. For the location of the terminals
and the distribution frame, use the Building Cable Plan developed
according to instructions in the “Planning the site” section in Installation
Planning (553-3001-120).
•
Install any IPE or Network Modules needed to house ISDN BRI cards as
determined in “Engineering guidelines” of ISDN Basic Rate Interface:
Product Description (553-3901-100). Refer to System Installation
Procedures (553-3001-210) for a description of how to install the
modules.
Unpack and inspect
ISDN BRI cards and external communication cables are shipped in separate
packages. To unpack them, follow the general precautions recommended by
computer and telephone equipment manufacturers.
•
•
•
•
Remove items that generate static charge from the installation site.
If the installation site is carpeted, spray it with an antistatic spray.
Ground yourself before handling any equipment.
Carefully remove the equipment from its packaging. Do not puncture or
tear the containers. Use scissors or a utility knife.
•
•
Inspect the equipment for obvious faults or damage. Report any damaged
component to your sales representative and the carrier who delivered the
equipment.
When unpacking the circuit cards, hold them only by their
non-conductor edges. Do not touch connector pins or components.
553-3901-200 Standard 7.00 January 2002
Preinstallation preparation Page 11 of 46
•
•
Keep the circuit cards in their antistatic bags until you are ready to install
them.
Do not stack the plug-in cards on top of each other. This can damage the
components and the printed circuits on the cards.
Take inventory
After unpacking, verify that all the equipment necessary is at the site before
installation begins. Check the equipment received against the shipping
documents. Note any shortages and report them to your sales representative.
ISDN Basic Rate Interface Installation
Page 12 of 46
Preinstallation preparation
553-3901-200 Standard 7.00 January 2002
46
Page 13 of 46
Install ISDN BRI hardware
Contents
The following are the topics in this section:
Install ISDN BRI hardware for line applications . . . . . . . . . . . . . . . . .
Select the card slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
15
19
20
21
21
22
22
Remove the module cover for card installation . . . . . . . . . . . . . . . .
Install the MISP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remove the MISP . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install the BRSC, SILC and UILC . . . . . . . . . . . . . . . . . . . . . . . . . .
Remove the BRSC, SILC and UILC . . . . . . . . . . . . . . . . . . . . . . . .
Connect ISDN BRI terminals to Meridian 1 . . . . . . . . . . . . . . . . . .
Install ISDN BRI hardware for trunk applications . . . . . . . . . . . . . . . .
Select the card slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remove the module cover for card installation . . . . . . . . . . . . . . . .
Install the MISP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install the clock reference on the SILC . . . . . . . . . . . . . . . . . . . . . .
Install the SILC and the UILC . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connect Meridian 1 to the Main Distribution Frame (MDF) . .. . . .
Cross-connect the Main Distribution Frame (MDF) . . . . . . . . . . . .
Card location forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
38
38
38
38
42
42
42
44
Reference list
The following are the references in this section:
•
Meridian Communications Unit and Meridian Communications
Adapter: Description, Installation, Administration, Operation
(553-2731-109)
ISDN Basic Rate Interface Installation
Page 14 of 46
Install ISDN BRI hardware
•
•
•
•
ISDN PRI: Installation (553-2901-201)
System Installation Procedures (553-3001-210)
ISDN Basic Rate Interface: Product Description (553-3901-100)
ISDN Basic Rate Interface: Administration (553-3901-300)
Install ISDN BRI hardware for line applications
The following lists the procedures for installing ISDN BRI hardware for line
applications. Meridian 1 must already be installed and operating according to
the instructions in System Installation Procedures (553-3001-210) before
performing these procedures.
For a successful installation, perform these procedures in the order listed
below:
1
2
3
4
5
Select the card slots where the ISDN BRI cards will be located
Remove the module cover for card installation
Install the MISPs
Install the SILCs and/or UILCs or BRSCs
Connect ISDN BRI terminals. This procedure comprises the following:
— connect the Meridian 1 to the Main Distribution Frame (MDF)
— cross connect the MDF
— connect ISDN BRI terminals to the DSL
— initialize the ISDN BRI terminals.
—————————— End of Procedure ——————————
553-3901-200 Standard 7.00 January 2002
Select the card slots
To install ISDN BRI cards, perform the following steps:
1
Identify all the slots that can contain them. First identify the modules
with unused network and peripheral card slots and then remove the
covers from the identified modules. To identify the modules, use the
following Print Programs. Table 1 lists the modules that can house
ISDN BRI cards.
•
LD 22 to print the system configuration and identify unused
network card slots to install MISPs
•
LD 20 to list unused IPE card slots to install SILCs, UILCs and
BRSCs
Table 1
ISDN BRI card location
SILCs,
UILCs,
BRSCs
Supported
Systems
Modules
MISPs
NT5D21
Core/Network Module 81C
51C, 61C,
Network
slots
—
0-7
NT8D35
Network Module
81C
Network
slots
—
5-12
NT8D37
IPE Module
All systems
IPE slots
0-15
—
2
Locate the card slots in the Meridian 1 modules which can house ISDN
BRI cards. Group all SILCs, UILCs, BRSCs, superloops and the MISP
that supports them in the same network group to avoid using junctors
for dedicated connections.
The following rules apply when selecting the card slots:
ISDN Basic Rate Interface Installation
Page 16 of 46
Install ISDN BRI hardware
MISPs
•
MISPs are inserted into the CE/Network Module for options 51C and
61C, and the Network Module for options 81C. Refer to the LD 22
printout to identify modules with unused network card slots and to
Table 1 for the card slots in these modules that can house MISPs.
•
An MISP cannot share network loop addresses with a Superloop
Network Card in options 51C, 61C, and 81C. The MISP requires two
network loop addresses and one network card slot.
•
•
An MISP supports a maximum of eight BRSCs and two line cards.
An MISP supports a set of four SILCs or UILCs when not supporting a
BRSC.
•
An MISP can support both BRSCs and SILCs or UILCs at the same time.
If it serves one BRSC, a MISP can also support three line cards. If it
supports two or more BRSCs, a MISP can also support two line cards.
BRSCs
•
•
Install one BRSC per IPE module.
With a BRSC configured, an IPE module can support a maximum of 15
line cards. These may be up to eight UILCs combined with any other
seven peripheral cards (including SILCs), or up to 15 SILCs.
SILCs/UILCs
SILCs, UILCs and BRSCs are installed into the IPE card slots of the
•
CE/PE Module and/or the IPE Module for option 21E. They are installed
into the IPE Module for all other system options. Refer to the LD 20
printout to identify modules with unused peripheral card slots.
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 17 of 46
•
•
In each module, install a maximum of 15 SILCs, or eight UILCs
combined with any other seven peripheral cards (including SILCs). If 15
SILCs are installed, the remaining slots in the module may contain a
BRSC, a UILCs or non-ISDN BRI cards that do not need the - 48 V
other card which could reside in the IPE module.
Group all SILCs, UILCs, BRSCs and the MISP that supports them in the
same network group to avoid using junctors for dedicated connections.
The figures that follow show typical module configurations.
Figure 1 shows the NT8D35 Network module.
Figure 2 shows the NT8D37 IPE module.
Figure 3 shows the NT5D21 Core/Network module.
Figure 1
NT8D35 Network module
CE Module
Net
Network-type cards:
NT8D04 Superloop Net
QPC414 Network Card
NT8D17 Conference/TDS
PRI/DTI (5-9)
SDI
DCHI (5-13)
MSDL (5-13)
MISP
1
2
3
4
5
6
7
8
9
SLP
10
11
SLP
12
13
14
CE Pwr Sup
3PE
IGS 1
IGS 0
PS
SLP
SLP
Network Group
Shelf
Common Equipment
553-7692
ISDN Basic Rate Interface Installation
Page 18 of 46
Figure 2
Install ISDN BRI hardware
NT8D37 IPE module
PE Module
IPE
Intelligent
line and trunk
cards
Intelligent
line and trunk
cards
0
1
2
3
4
5
6
7
Cont
8
9
10
11
12
13
14
15
PE Pwr Sup
Rng Gen
Superloop
Shelf
Intelligent
Peripheral Equipment
553-7694
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 19 of 46
Figure 3
NT5D21 Core/Network module
Core/Net Module
Net
Core
LRTN
FGND
0
SLP
1
2 3
SLP
4 5
SLP
6 7
SLP
8
9
10 11 12 13 14 15 16 17 18
PS 3PE CNI
CE Pwr Sup
NT5D21
Network Group
Shelf
CPU
Core/Net Module
553-6383
Remove the module cover for card installation
To remove the covers from Meridian 1 modules with unused card slots,
follow the procedure below. Refer to Figure 4.
1
2
3
Use a flat-blade screwdriver to unlock the left latch on the front of the
cover by turning the screw 1/4 turn clockwise.
Use a flat-blade screwdriver to unlock the right latch on the front of the
cover by turning the screw 1/4 turn counterclockwise.
While holding the cover so it does not fall off, slide the latches toward
the center of the cover.
4
5
Pull the cover toward you and lift it away from the module.
Place the cover in a safe place away from the working area to avoid
damaging it.
6
Repeat steps 1 through 5 for each cover requiring removal.
ISDN Basic Rate Interface Installation
Page 20 of 46
Figure 4
Install ISDN BRI hardware
Module cover locking latches
Meridian 1
Turntounlock
Slideto
unlatchcover
Lock screw
Sliding Latch Knob
553-7695
Install the MISP
Once covers have been removed and card slot locations selected for ISDN
BRI cards, install the MISP cards.
1
2
3
4
5
Hold the MISP by its card-locking devices. Squeeze the tabs to unlatch
the card-locking devices and lift the tabs out and away from the card.
Insert the MISP into the selected card slot of the module so it engages
the card guides in the module.
Slide the MISP into the module until it engages the backplane
connector.
Push the MISP firmly into the connector using the locking devices as
levers by pushing them toward the card's front panel.
Push the tabs firmly against the front panel of the card so they latch to
the front lip in the module and to the post on the card.
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 21 of 46
Observe the red LED on the MISP faceplate.
6
•
•
•
If the red LED lights and stays lit continuously without flashing
three times, the card is defective. Remove the MISP, choose a
new MISP, and repeat the installation procedure.
If the red LED lights, flashes three times, and turns off, the
MISP is operating correctly and is configured and enabled. Go
to step 7.
If it lights, flashes three times, and stays lit continuously, the
MISP is operating correctly but is not configured and enabled.
Go to step 7.
7
Repeat steps 1 through 6 for each MISP requiring installation.
—————————— End of Procedure ——————————
Remove the MISP
1
Hold the MISP by its card-locking devices. Squeeze the tabs to unlatch
the card-locking devices and lift the tabs out and away from the card.
2
Carefully remove the MISP from its card slot, and slowly slide out the
card from the module.
—————————— End of Procedure ——————————
Install the BRSC, SILC and UILC
After MISPs are installed, install SILCs, UILCs and BRSCs, as required. As
the cards are installed, keep a list of the card type (BRSC, SILC or UILC), the
module number, and the number of the card slot containing the card. Use the
CE/PE Module card location form or the IPE Module card location form at
the end of this chapter to document this information.
1
2
3
4
Hold the card by its card-locking devices. Squeeze the tabs to unlatch
the card-locking devices and lift them away from the card.
Insert the BRSC, SILC or UILC into the selected card slot of the
module so it engages the card guides in the module.
Slide the BRSC, SILC or UILC into the module until it engages the
backplane connector.
Push the card firmly into the connector using the locking devices as
levers by pushing them toward the card's front panel.
ISDN Basic Rate Interface Installation
Page 22 of 46
Install ISDN BRI hardware
5
6
Push the tabs firmly against the front panel of the card so they latch to
the front lip in the module and to the post on the card.
Observe the red LED located on the faceplate.
•
If the red LED turns on and stays lit continuously, the card is
defective. Remove the card, choose a new card, and repeat
the installation procedure.
•
•
If it flashes three times and then turns off, the card is operating
correctly. Go to step 7.
If the red LED flashes three times and then stays lit
continuously, the card is operating correctly but is not
configured. Go to step 7.
7
8
On the CE/PE or IPE Module Card Location Form, fill in the card type
and the module number next to the slot number of the installed card.
Repeat steps 1 through 7 for each card requiring installation.
—————————— End of Procedure ——————————
Remove the BRSC, SILC and UILC
1
Hold the card by its card-locking devices. Squeeze the tabs to unlatch
the card-locking devices and lift them away from the card.
2
Carefully disengage the BRSC, SILC or UILC from the backplane
connector, and slowly slide out the card from the module.
—————————— End of Procedure ——————————
Connect ISDN BRI terminals to Meridian 1
following procedures.
•
•
•
connect the Meridian 1 to the Main Distribution Frame (MDF)
cross connect the MDF
connect the ISDN BRI terminals to the DSL
Figure 5 shows a typical DSL with ISDN BRI terminals connected to it using
modular cables.
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 23 of 46
Figure 5
Connect ISDN BRI terminals to Meridian 1
Main
Distribution
Frame
NE-A25BCable
Meridian 1
Intermediate
Distribution
Frames
IPEI/OPanel
SILC DSL (Office Wiring)
Modular Cable
Wall Outlets
Terminating
Resistor
553-7696
ISDN Basic Rate Interface Installation
Page 24 of 46
Install ISDN BRI hardware
Connect Meridian 1 modules to the MDF
Meridian 1 modules connect to the MDF using NE-A25B cables with 50-pin
D-type male connectors on each end. One end of the cable plugs into the I/O
panel at the rear of the Meridian 1 module and the other end plugs into the
MDF.
Figure 6 shows the cable connection between the Meridian 1 and the MDF.
1
2
3
Determine the number of NE-A25B cables needed to connect one
module to the MDF.
Label each end of the cable specifying the module number, the
connector name (A, B, C), and the card type (SILC or UILC).
Plug one end of a cable into the appropriate connector on the I/O panel
at the rear of the Meridian 1 module. Plug the other end of the cable
into the corresponding connector on the MDF.
4
Properly identify cables on the MDF. For example, plug the cable into
MDF if an SILC or UILC is installed in slot 0 of an IPE module.
5
6
Repeat steps 2 through 4 for all cables in that module.
Repeat steps 1 through 5 for all modules containing SILCs and/or
UILCs.
7
8
Lay all the cables neatly and fasten them with cable ties.
Label the MDF, as necessary, using Table 2 through Table 5.
—————————— End of Procedure ——————————
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 25 of 46
Figure 6
Connect the Meridian 1 to the MDF
IPE I/O panel
CE/PE I/O panel
C B
Meridian 1
B
A
A
Meridian 1
J2
F E
C
F E
G
K H
J3
NE-A25B External
Communication Cable
Main Distribution Frame
A
Rear
B
C
E
F
G
553-7697
SILC/UILC port designations at the MDF
The tables that follow provide SILC/UILC port designations at the MDF, for
the NT8D37 IPE.
ISDN Basic Rate Interface Installation
Page 26 of 46
Install ISDN BRI hardware
Table 2 shows the SILC port designation labels for the IPE Module. The
UILC port designation labels for the IPE and CE/PE Modules is shown in
Table 3.
Table 2
SILC port designations at the MDF: NT8D37 IPE Module (16-cable configuration)
(Part 1 of 2)
0
A
B
C
D
E
F
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
A
B
C
D
E
F
0
1
2
3
4
5
6
7
1
2
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
0
1
2
3
4
5
6
7
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
0
1
2
3
4
5
6
7
3
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
0
1
2
3
4
5
6
7
4
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
0
1
2
3
4
5
6
7
5
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
0
1
2
3
4
5
6
7
6
G
H
K
L
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
G
H
K
L
0
1
2
3
4
5
6
7
7
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
0
1
2
3
4
5
6
7
8
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
0
1
2
3
4
5
6
7
9
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
0
1
2
3
4
5
6
7
10
M
N
R
S
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
M
N
R
S
0
1
2
3
4
5
6
7
11
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
0
1
2
3
4
5
6
7
12
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
0
1
2
3
4
5
6
7
13
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
0
1
2
3
4
5
6
7
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 27 of 46
Table 2
SILC port designations at the MDF: NT8D37 IPE Module (16-cable configuration)
(Part 2 of 2)
14
T
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
T
0
1
2
3
4
5
6
7
15
T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T+R+R- T-T +R+ R
U
U
0
1
2
3
4
5
6
7
Note 1: For the SILC port designations shown in this table, substitute Tx- Tx+ Rx+ Rx- for every
occurrence of T- T+ R+ R-.
Note 2: The cable pair designated Tx- Tx+ is the transmit pair. The pair designated Rx+ Rx- is the
receive pair. An SILC port supplies 2 watts of power at -48 V (-40 V for international), simplexed over the
transmit and receive pairs, where the transmit pair is negative with respect to the receive pair.
Table 3
UILC port designation labels at the MDF: NT8D37 IPE Module (16-cable configuration)
(Part 1 of 2)
0
A
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
A
1
B
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
B
C
D
E
F
2
C
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
3
D
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
4
E
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
5
F
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
6
G
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
G
H
K
7
H
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
8
K
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
ISDN Basic Rate Interface Installation
Page 28 of 46
Table 3
Install ISDN BRI hardware
UILC port designation labels at the MDF: NT8D37 IPE Module (16-cable configuration)
(Part 2 of 2)
9
L
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
L
10
M
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
M
N
R
S
T
11
N
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
12
R
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
13
S
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
14
T
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
15
U
TR
0
TR
1
TR
2
TR
3
TR
4
TR
5
TR
6
TR
7
U
Note: The cable pair designated TR is a 2B1Q full duplex U interface.
Cross-connect the MDF
The MDF cross-connects NE-A25B cables connected to SILC and UILC
ports with building wiring connected to ISDN BRI terminals.
Each SILC provides eight four-wire full duplex ports. These ports are
Signal polarity must be maintained along each loop.
Each UILC provides eight two-wire full duplex ports. These ports are
connected to twisted pair building wiring to form DSLs. These DSLs are not
polarity sensitive and, although it is recommended, it is not necessary to
maintain signal polarity along each loop.
Figure 7 and Figure 8 illustrate, respectively, a cross-connection of an SILC
port and an UILC port to the building wiring.
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 29 of 46
Cross-connect SILC and/or UILC ports to the building wiring
1
Refer to the IPE or CE/PE module card location form, which shows the
card type connected to each I/O panel connector.
2
Identify transmit and receive pairs on the top of the labeled distribution
strip for the card type and module type you are connecting. To identify
SILC or UILC ports and their pin numbers, refer to Tables 4 through
10, which follow the illustrations.
Note: In Tables 4 through 10, the cable pair designated T- T+ is the
transmit pair and the pair designated R+ R- is the receive pair of the
S/T interface. The cable pair designated T R is the Tx and Rx of the
2B1Q full duplex U interface.
3
4
Identify building wires connected to the bottom of the distribution strip.
Refer to the Building Cable Plan, which identifies wires between
distribution frames and wall outlets.
Plug in the terminating resistor (Part Number A0378866) at the
appropriate location in each S/T DSL. See “Engineering Guidelines” in
the ISDN Basic Rate Interface: Product Description (553-3901-100) for
engineering rules and locations of terminating resistors.
ISDN Basic Rate Interface Installation
Page 30 of 46
Figure 7
Install ISDN BRI hardware
Cross-connect the SILC port to the office wiring
Port
0
Distribution frame (Note 1)
1
2
3
4
5
6
7
8
9
10
26
T-
27
R+
28
T-
29
30
T-
31
32
T-
33
34
T-
35
T+
R-
T+
Port
R+
R-
T+
R+
R-
T+
R+
R-
T+
R+
R-
A
B
1
Port
2
Port
3
Port
4
Cross connect wires or
cable for DS1
Auxilary Power Source if more that 2 W
are required for DSL 1
Port
0
Power Source 2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
A
B
DSL 2
DSL 3
1
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Port 0
Port 1
Port 2
Port 3
Port 4
2
DSL 1 wiring for
SILC Port 0
3
4
RJ - 45 type
wall outlet
5
6
7
1
2
8
9
3
4
5
6
7
8
R+
T+
T-
R-
P-
WHT/ORG
BLU/WHT
WHT/BLU
ORG/WHT
GRN/WHT
WHT/GRN
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Port 5
Port 6
P+
Port 7
Maximum stub length
1 m or 3.3 feet
1
2
3
4
5
6
7
8
R+
T+
T-
R-
P-
WHT/ORG
BLU/WHT
WHT/BLU
ORG/WHT
GRN/WHT
WHT/GRN
Loop terminator
resistor box
A0378866
P+
RJ - 45 type
wall outlet
100 Ohm
NE-A25B cable connector connecting
distribution frame connector A
Note 1: Substitute Tx- Tx+ Rx- Rx+ for every occurance of T- T+ R-R+
Note 2: Transmit and receive labeling is from the network perspective
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 31 of 46
Figure 8
Cross-connect the UILC port to the office wiring
Distribution frame
1
2
3
4
5
6
7
8
9
10
26
T
27
28
T
29
1
30
T
31
2
32
T
33
3
34
T
35
4
R
R
R
R
R
A
B
Port
0
Port
Port
Port
Port
Cross connect wires or
cable for DS1
DSL1
4
1
2
3
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
A
B
DSL 2
DSL 3
DSL 1 wiring for
SILC Port 0
1
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Port 0
Port 1
Port 2
2
3
4
RJ - 45 type
wall outlet
5
6
7
1
2
Port 3
Port 4
Port 5
Port 6
Port 7
8
9
3
4
5
6
7
8
R+
T+
T-
R-
P-
WHT/ORG
BLU/WHT
WHT/BLU
ORG/WHT
GRN/WHT
WHT/GRN
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
P+
(U - Interface)
NE-A25B cable connector connecting
distribution frame connector A
553-7699
ISDN Basic Rate Interface Installation
Page 32 of 46
Table 4
Install ISDN BRI hardware
NT8D37 IPE module
SILC and UILC pair-terminations for connectors A, E, K, R (12-cable configuration)
Port signals
I/O panel connectors
Card
port
Pairs
Pair color
SILC
UILC
A
E
K
R
0Tx - / 0Tx +
0Rx + / 0Rx -
0T / 0R
26 / 1 W-BL / BL-W
27 / 2 W-O / O-W
slot 0 slot 4 slot 8 slot 12
0
1
2
3
4
5
6
7
1Tx - / 1Tx +
1Rx + / 1Rx -
1T / 1R
2T / 2R
3T / 3R
4T / 4R
28 / 3 W-G / G-W
29 / 4 W-BR / BR-W
2Tx - / 2Tx +
2Rx + / 2Rx -
30 / 5 W-S / S-W
31 / 6 R -BL / BL-R
3Tx - / 3Tx +
3Rx + / 3Rx -
32 / 7 Rx-O / O-R
33 / 8 R -G / G-R
4Tx - / 4Tx +
4Rx + / 4Rx -
34 / 9 R-BR / BR-R
35 / 10 R-S / S-R
5Tx - / 5Tx +
5Rx + / 5Rx -
5T / 5R 36 / 11 BK-BL / BL-BK
37 / 12 BK-O / O-BK
6Tx - / 6Tx +
6Rx + / 6Rx -
6T / 6R 38 / 13 BK-G / G-BK
39 / 14 BK-BR / BK-BR
7Tx - / 7Tx +
7Rx + / 7Rx -
7T / 7R 40 / 15 BK-S / S-BK
41 / 16 Y-BL / BL-Y
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 33 of 46
Table 5
NT8D37 IPE module
SILC and UILC pair-terminations for connectors B, F, L, S (12-cable configuration)
Port signals I/O panel connectors
SILC UILC
Card
port
Pairs
Pair color
B
F
L
S
0Tx - / 0Tx + 0T / 0R
0Rx + / 0Rx -
26 / 1
27 / 2
W-BL / BL-W
W-O / O-W
slot 1 slot 5 slot 9 slot 13
0
1
2
3
4
5
6
7
0
1
2
3
1Tx - / 1Tx + 1T / 1R
1Rx + / 1Rx -
28 / 3
29 / 4
W-G / G-W
W-BR / BR-W
2Tx - / 2Tx + 2T / 2R
2Rx + / 2Rx -
30 / 5
31 / 6
W-S / S-W
R-BL / BL-R
3Tx - / 3Tx + 3T / 3R
3Rx + / 3Rx -
32 / 7
33 / 8
R-O / O-R
R-G / G-R
4Tx - / 4Tx + 4T / 4R
4Rx + / 4Rx -
34 / 9
35 / 10 R-S / S-R
R-BR / BR-R
5Tx - / 5Tx + 5T / 5R
5Rx + / 5Rx -
36 / 11 BK-BL / BL-BK
37 / 12 BK-O / O-BK
6Tx - / 6Tx + 6T / 6R
6Rx + / 6Rx -
38 / 13 BK-G / G-BK
39 / 14 BK-BR / BK-BR
7Tx - / 7Tx + 7T / 7R
7Rx + / 7Rx -
40 / 15 BK-S / S-BK
41 / 16 Y-BL / BL-Y
0Tx - / 0Tx + 0T / 0R
0Rx + / 0Rx -
42 / 17 Y-O / O-Y
43 / 18 Y-G / G-Y
slot 2 slot 6 slot 10 slot 14
1Tx - / 1Tx + 1T/ 1R
1Rx + / 1Rx -
44 / 19 Y-BR / BR-Y
45 / 20 Y-S / S-Y
2Tx - / 2Tx + 2T / 2R
2Rx + / 2Rx -
46 / 21 V-BL / BL-V
47 / 22 V-O / V-O
3Tx - / 3Tx + 3T / 3R
3Rx + / 3Rx -
48 / 23 V-G / G-V
49 / 24 V-BR / BR-V
ISDN Basic Rate Interface Installation
Page 34 of 46
Table 6
Install ISDN BRI hardware
NT8D37 IPE module
SILC and UILC pair-terminations for connectors C, G, M, T (12-cable configuration)
Port signals
SILC UILC
I/O panel connectors
Card
port
Pairs
Pair color
C
G
M
T
4Tx - / 4Tx + 4T / 4R
4Rx + / 4Rx -
26 / 1
27 / 2
W-BL / BL-W
W-O / O-W
slot 2 slot 6 slot 10 slot 14
4
5
6
7
0
1
2
3
4
5
6
7
5Tx - / 5Tx + 5T / 5R
5Rx + / 5Rx -
28 / 3
29 / 4
W-G / G-W
W-BR / BR-W
6Tx - / 6Tx + 6T / 6R
6Rx + / 6Rx -
30 / 5
31 / 6
W-S / S-W
R-BL / BL-R
7Tx - / 7Tx + 7T / 7R
7Rx + / 7Rx -
32 / 7
33 / 8
R-O / O-R
R-G / G-R
0Tx - / 0Tx + 0T / 0R
0Rx + / 0Rx -
34 / 9
35 / 10 R-S / S-R
R-BR / BR-R
slot 3 slot 7 slot 11 slot 15
1Tx - / 1Tx + 1T / 1R
1Rx + / 1Rx -
36 / 11 BK-BL / BL-BK
37 / 12 BK-O / O-BK
2Tx - / 2Tx + 2T / 2R
2Rx + / 2Rx -
38 / 13 BK-G / G-BK
39 / 14 BK-BR / BK-BR
3Tx - / 3Tx + 3T / 3R
3Rx + / 3Rx -
40 / 15 BK-S / S-BK
41 / 16 Y-BL / BL-Y
4Tx - / 4Tx + 4T / 4R
4Rx + / 4Rx -
42 / 17 Y-O / O-Y
43 / 18 Y-G / G-Y
5Tx - / 5Tx + 5T / 5R
5Rx + / 5Rx -
44 / 19 Y-BR / BR-Y
45 / 20 Y-S / S-Y
6Tx - / 6Tx + 6T / 6R
6Rx + / 6Rx -
46 / 21 V-BL / BL-V
47 / 22 V-O / V-O
7Tx - / 7Tx + 7T / 7R
7Rx + / 7Rx -
48 / 23 V-G / G-V
49 / 24 V-BR / BR-V
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 35 of 46
Connect the ISDN BRI terminals to the DSL
ISDN BRI terminals are connected to DSLs using modular cables up to 10
meters (33 feet) long, with RJ-45 plugs on each end. One end of the cable
Note: All ISDN BRI terminals should comply with CCITT, ANSI,
ETSI NET-3, INS NET-64, National ISDN, 1TR6, Numeris VN2, and
D70 standards for terminals, and be compatible with Meridian 1. For a
list of compatible terminals, refer to the ISDN Basic Rate Interface:
Product Description (553-3901-100).
Figure 9 illustrates a terminal connection to the S/T interface; Figure 10
illustrates a network termination (NT1) connection to the U interface.
1
Plug one end of the modular cable into the ISDN BRI interface
connector on the terminal, and the other end of the modular cable into
the wall outlet.
2
For an SILC S/T interface terminal with an optional auxiliary power
source, plug the power source into the wall outlet, then plug the cable
into the power source's RJ-45 jack. This power source must supply
power only to the local ISDN BRI terminal, not back into the DSL
through the RJ-45 wall outlet. The power adapter is supplied with the
terminal.
3
4
Program the terminal parameters, such as the SPID and TEI, as
required by the type of terminal. For detailed information pertaining to
this procedure, refer to the section “Initialize ISDN BRI terminals”,
found in ISDN Basic Rate Interface: Administration (553-3901-300).
Repeat steps 1 and 3 for each terminal to be connected.
—————————— End of Procedure ——————————
Connect the terminating resistors
DSLs require that a terminating resistor (Part Number A0378866) be
connected at the end of each loop. See ISDN Basic Rate Interface: Product
Description (553-3901-100), for engineering rules and locations of
terminating resistors. The end of the S/T interface loop has a RJ-45 jack to
plug in the telephone cable. Plug the terminating resistor into the RJ-45 and
then plug the telephone cable into the terminating resistor. Note that for every
port there is one loop with only one terminating resistor per loop. Each loop
may have up to eight telephones.
ISDN Basic Rate Interface Installation
Page 36 of 46
Figure 9
Install ISDN BRI hardware
Connect the ISDN BRI terminal to the S/T interface
Optional Power Adapter
RJ-45 type
wall outlet
RJ-45 type plug
1
2
DSL wiring
1
2
3
4
5
6
7
8
3
4
R+
T+
T-
R-
P-
P+
WHT/ORG
BLU/WHT
WHT/BLU
ORG/WHT
GRN/WHT
WHT/GRN
5
6
7
8
S/T interface
Modular cable
(maximum
length 10 m)
Optional
external power
source (PS 52)
Voice Data
terminal
3 Rx+
4 Tx+
5 Tx-
3
4
5
6
6 Rx-
7 P-
7
8
8 P+
Printer
1
2
3 Tx+
4 Rx+
5 Rx-
6 Tx-
7 P-
8 P+
S/T interface connector
on the ISDN/BRI terminal
553-7700
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 37 of 46
Figure 10
Connect the ISDN BRI network termination (NT1) to the U interface
RJ-45 type
wall outlet
RJ - 45
1
type plug
2
RJ - 45
type plug
3
4 R
5T
4R
5T
6
7
8
4 R
5T
Modular cable maximum
length 10 m
Office Wiring
U interface
1
2
1
2
3
R+ 3
NT1
power source
U+ U+S/TS/T
NT1
T+ 4
4 R
U
T- 5
R- 6
5 T
6
P -7
P +8
7
8
S/T Interface Connector on
the Network Termination
(NT1)
U Interface Connector on
the Network Termination
(NT1)
S/T interface DSL cable to
the ISDN BRI terminals
RJ - 45
type plug
WHT/ORG Rx + 3
BLU/WHT Tx + 4
WHT/BLU Tx - 5
ORG/WHT Rx - 6
GRN/WHT P - 7
WHT/GRN P+ 8
Terminal Auxiliary
power source PS 2
553-7701
ISDN Basic Rate Interface Installation
Page 38 of 46
Install ISDN BRI hardware
Install ISDN BRI hardware for trunk applications
The following lists the procedures for install ISDN BRI hardware for ISDN
BRI trunk applications. Meridian 1 must already be installed and operating
according to the instructions in System Installation Procedures
(553-3001-210) before performing these procedures.
For a successful installation, perform these procedures in the order listed
below:
1
2
3
4
5
6
Select the card slots where the ISDN BRI cards will be located
Install the MISP
Install clock referencing on the SILC
Install the SILC and/or UILC
Connect Meridian 1 to the MDF
Cross-connect the MDF (in Terminal Equipment mode)
Note: The Meridian 1, in Tie trunk or CO connectivity, requires a
different wiring configuration than for a line application; the transmit and
receive pairs should be reversed, as illustrated in Figure 12.
Select the card slots
Follow the same procedures as described earlier for line applications (refer to
“Select the card slots” on page 15).
Remove the module cover for card installation
Follow the same procedures as described earlier for line applications (refer to
“Remove the module cover for card installation” on page 19).
Install the MISP
Follow the same procedures as described earlier for line applications (refer to
“Install the MISP” on page 20).
Install the clock reference on the SILC
The DSL#0 and DSL#1 on an SILC card can be configured as the reference
clock source, with DSL#0 being assigned for the primary clock reference and
DSL#1 being assigned for the secondary clock reference.
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 39 of 46
The loop number and location of the primary and secondary clock source is
configured in the Digital Data Block overlay 73. Refer to the ISDN Basic Rate
Interface: Administration (553-3901-300).
The following procedure should be followed to provide clock referencing on
the SILC.
Note: For procedures on how to install the QPC775/QPC471 Clock
Controller on the various Meridian 1 systems, please refer to ISDN PRI:
Installation (553-2901-201).
1
2
Maintain the same polarity on each transmit and receive. Rewire the
selected Tx and Rx pairs (applicable to DSL0 and DSL1), to exchange
the Tx and Rx pair position. This rewiring is done at the Main
Distribution Frame (MDF).
Remove the phantom power jumpers (two jumpers per DSL) from the
pin headers.
3
4
5
Place the SILC in the selected IPE slot.
Configure the selected DSL as TE mode (in overlay 27).
Enable the clock in overlay 60, to output the clock references to the
IPE back plane pins.
6
7
Configure the Clock Controller card to accept ISDN BRI clock
reference.
Check the appropriate messages from the Clock Controller to ensure
that it is synchronized to the proper clock reference (this is done using
overlay 60).
8
Connect the ISDN BRI clock reference cables to the Clock Controller,
using the procedures which follow.
—————————— End of Procedure ——————————
ISDN Basic Rate Interface Installation
Page 40 of 46
Install ISDN BRI hardware
Connect clock reference cables
The following procedure should be followed to connect the ISDN BRI clock
reference cables to the Clock Controller. There are three different cables that
route clock signals from the IPE back plane to the Clock Controller face plate
(as shown in Figure 11). These are shown in Table 7.:
Table 7
ISDN BRI clock reference tables
Code
Length (feet)
Use
NTND70AA
1.5
Connects IPE back plane to
IPE I/O panel.
NTND71AA-AD
NTND72AA
6.5, 12, 25, 42
6.5
Connects IPE I/O to CE I/O
panel.
Connects CE I/O to Clock
Controller face plate.
Note: Measure the distance between the IPE and CE modules to ensure
that you order the correct cable lengths.
1
2
Search for available D-sub 9 connector slots on the I/O panels of the
selected IPE and CE I/O modules (if the I/O panel is equipped with
D-sub 9 connector slots). If none is available, look for an empty slot
used for 25 pair wire connectors (the cables contain two adapter plates
to convert an 25 wire slot to two D-sub 9 connector slots).
Connect the cables as shown in Figure 11; if choosing IPE slots 0, 4,
8, or 12 the transmit and receive cable installed on pins 72 - 79 should
be removed and secured to a proper place.
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 41 of 46
Figure 11
Clock reference cable connection
NTND71AA - AD
NTND70AA
IPE I/O panel
CE I/O panel
S
I
L
C
C
C
IPE shelf
CE shelf
NTND72AA
553-7702
Clock recovery
The SILC is configured in the slave-slave mode when acting as a trunk
interface. This is set up through the Maintenance Signaling Channel (MSC).
The microcontroller configures the S/T chips on the SILC as appropriate.
The SILC may recover the network clock from the received data stream using
on-chip phase lock loops. The clock frequency which is recovered is 2.56
MHz. The jitter and wander conform to CCITT recommendations.
ISDN Basic Rate Interface Installation
Page 42 of 46
Install ISDN BRI hardware
All of the S/T chips on the SILC could be configured as Terminal Equipment
Slaves (TES), but only the clocks recovered from DSL0 and DSL1 are routed
to the back plane connector pins. These clocks are provided as differential
pairs on back plane pins, as follows: in
Table 8
Clocks as differential pairs
Differential pairs
Pin #
Row A
Row B
Primary
73
74
75
76
+Ref 0A
+Ref 1A
+Ref 0B
+Ref 1B
- Ref 0A
- Ref 1A
- Ref 0B
- Ref 1A
Primary
Secondary
Secondary
timer. Tracking is restored to the primary reference clock, if defined. If the
primary reference clock is disabled, tracking is restored to the secondary
reference clock, if defined.
Install the SILC and the UILC
Follow the same procedures as described earlier for line applications (refer to
“Install the BRSC, SILC and UILC” on page 21).
Follow the same procedures as described earlier for line applications (refer to
“Connect Meridian 1 modules to the MDF” on page 24).
Cross-connect the Main Distribution Frame (MDF)
The Meridian 1, in Tie trunk or CO connectivity, requires a different wiring
configuration than for a line application; the transmit and receive pairs should
be reversed, as illustrated in Figure 12.
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 43 of 46
Figure 12
Connect the network termination to the U interface and to the S/T interface (in TE mode)
Distribution Frame
Distribution Frame
Port 0
26
26
1
27
2
28
3
29
4
30
T
5
31
6
1
27
2
28
3
29
4
30
5
31
6
T
R
T
R
R
Tx- Tx+ Rx+ Rx- Tx- Tx+ Rx+
Port 1
Tx- Tx+ Rx+ Rx-
Port 2
Rx-
Port 0
Port 1
Port 2
Cross-connectwires
or cable for DSL 1
Cross-connectwires
or cable for DSL 1
12
1
2
3
4
5
6
7
8
9
10 11
1
2
3
4
5
6
7
8
9
10 11 12
DSL 1
DSL 2
DSL 2
DSL 1 Wiring
for SILC Port 0
DSL 1 wiring for
UILC Port 0
Network Termination (NT1)
1
1
2
2
3
4
3
Tx-
Rx-
WHT/ORG
BLU/WHT
BLU/WHT T
4
5
Rx+ WHT/BLU
WHT/BLU
R
5
6
7
ORG/WHT
Tx+
6
7
8
8
1
2
1
2
3
Tx- 3
Rx- 4
4 T
Rx+ 5
Tx+ 6
7
5 R
6
U Interface Connector on
the Network Termination
(NT1)
S/T Interface Connector on
the Network Termination
(NT1)
7
8
8
553-7703
ISDN Basic Rate Interface Installation
Page 44 of 46
Install ISDN BRI hardware
Card location forms
The following card location forms may be used when installing SILC/UILC
and BRSC cards on the Meridian 1.
Table 9
Card location form: NT8D37 IPE Module (16-cable configuration)
Card type
(SILC/UILC/BRSC)
IPE Module
number
IPE Module
slot number
I/O panel
connector
SILC/UILC/BRSC
ports
0
1
A
B
C
D
E
F
0–7
0–7
0–7
0–7
0–7
0–7
0–7
0–7
0–7
0–7
0–7
0–7
0–7
0–7
0–7
0–7
2
3
4
5
6
G
H
K
L
7
8
9
10
11
12
13
14
15
M
N
R
S
T
U
553-3901-200 Standard 7.00 January 2002
Install ISDN BRI hardware Page 45 of 46
Table 10
Card location form: NT8D37 IPE Module (12-cable configuration)
Card Type
(SILC/UILC or BRSC)
IPE Module
number
IPE module
slot number connector
I/O panel
SILC/UILC or BRSC
ports
0
1
2
A
B
0–7
0–7
B
C
0–3
4–7
3
4
5
6
C
E
F
0–7
0–7
0–7
F
G
0–3
4–7
7
8
G
K
L
0–7
0–7
0–7
9
10
L
0–3
M
4–7
11
12
13
14
M
R
S
0–7
0–7
0–7
S
T
0–3
4–7
ISDN Basic Rate Interface Installation
Page 46 of 46
Install ISDN BRI hardware
553-3901-200 Standard 7.00 January 2002
Family Product Manual Contacts Copyright FCC notice Trademarks
Document number Product release Document release Date Publish
Meridian 1
ISDN Basic Rate Interface
Installation
Copyright © 1992–2002 Nortel Networks
All Rights Reserved
Information is subject to change without notice. Nortel
Networks reserves the right to make changes in
design or components as progress in engineering and
manufacturing may warrant. This equipment has been
tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC rules,
and the radio interference regulations of Industry
Canada. These limits are designed to provide
reasonable protection against harmful interference
when the equipment is operated in a commercial
environment. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at their
own expense.
SL-1 and Meridian 1 are trademark of Nortel
Networks.
Publication number: 553-3901-200
Document release: Standard 7.00
Date: January 2002
Printed in Canada
TM
|