NordicTrack Home Gym NTB14920 User Manual

Model No. NTB14920  
Serial No.  
Write the serial number in the  
space above for future reference.  
USER’S MANUAL  
Serial Number Decal (Under Seat)  
QUESTIONS?  
As a manufacturer, we are com-  
mitted to providing complete  
customer satisfaction. If you  
have questions, or if there are  
missing or damaged parts, we  
will guarantee complete satis-  
faction through direct assis-  
tance from our factory.  
TO AVOID DELAYS, PLEASE  
CALL DIRECT TO OUR TOLL-  
FREE CUSTOMER HOT LINE.  
The trained technicians on our  
customer hot line will provide  
immediate assistance, free of  
charge.  
CUSTOMER HOT LINE:  
1-888-825-2588  
Mon.–Fri., 6 a.m.–6 p.m. MST  
CAUTION  
Visit our website at  
Read all precautions and instruc-  
tions in this manual before using  
this equipment. Save this manual  
for future reference.  
new products, prizes,  
fitness tips, and much more!  
 
IMPORTANT PRECAUTIONS  
WARNING:  
To reduce the risk of serious injury, read the following important precautions  
before using the weight bench.  
1. Read all instructions in this manual before  
using the weight bench. Use the weight  
bench only as described in this manual.  
6. Keep children under 12 and pets away from  
the weight bench at all times.  
7. Keep hands and feet away from moving parts.  
2. It is the responsibility of the owner to ensure  
that all users of the weight bench are ade-  
quately informed of all precautions.  
8. Always wear athletic shoes for foot protec-  
tion while exercising.  
3. The weight bench is intended for home use  
only. Do not use the weight bench in any  
commercial, rental, or institutional setting.  
9. The weight bench is designed to support a  
maximum user weight of 300 pounds, and a  
maximum total weight of 610 pounds. Do not  
use the weight bench with more than 310  
pounds of weight. Do not place more than  
150 pounds on the leg lever. Note: The  
weight bench does not include weights.  
4. Use the weight bench only on a level surface.  
Cover the floor beneath the weight bench to  
protect the floor.  
5. Make sure all parts are properly tightened  
each time the weight bench is used. Replace  
any worn parts immediately.  
10. If you feel pain or dizziness at any time while  
exercising, stop immediately and begin cool-  
ing down.  
WARNING:  
Before beginning this or any exercise program, consult your physician. This  
is especially important for persons over the age of 35 or persons with pre-existing health problems.  
Read all instructions before using. ICON assumes no responsibility for personal injury or property  
damage sustained by or through the use of this product.  
3
 
BEFORE YOU BEGIN  
Thank you for selecting the versatile NordicTrack®  
STRENGTH COMBINATION BENCH weight bench.  
The weight bench offers a selection of weight stations  
designed to develop every major muscle group of the  
body. Whether your goal is to tone your body, build  
dramatic muscle size and strength, or improve your  
cardiovascular system, the weight bench will help you  
to achieve the specific results you want.  
toll-free at 1-888-825-2588, Monday through Friday,  
6 a.m. until 6 p.m. Mountain Time (excluding holidays).  
To help us assist you, please note the product model  
number and serial number before calling. The model  
number is NTB14920. The serial number can be found  
on a decal attached to the weight bench (see the front  
cover of this manual).  
Before reading further, please review the drawing  
below and familiarize yourself with the parts that are  
labeled.  
For your benefit, read this manual carefully before  
using the weight bench. If you have additional ques-  
tions, please call our Customer Service Department  
Backrest  
Curl Pad  
Curl Bar  
Adjustment Arm  
Wheel  
Adjustment Knobs  
Seat  
Leg Lever  
4
 
PART IDENTIFICATION CHART  
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-  
ing is the key number of the part, from the PART LIST on page 14 of this manual. Note: Some small parts may  
have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.  
M4 x 16mm Screw (41)  
M6 x 16mm Screw (38)  
M10 x 63mm Button Head Bolt (37)  
M12 x 75mm Button Head Bolt (36)  
M12 Washer (40)  
M10 Washer (33)  
M10 x 80mm Carriage Bolt (39)  
M12 x 87mm Button Head Bolt (34)  
M10 x 115mm Carriage Bolt (35)  
M5 x 11mm  
Screw (51)  
M10 Nylon Locknut (32)  
M12 Nylon Lockut (47)  
5
 
ASSEMBLY  
Place all parts in a cleared area and remove the  
packing materials. Do not dispose of the packing  
materials until assembly is completed.  
Make Things Easier for Yourself  
This manual is designed to ensure that the  
weight bench can be assembled successfully  
by anyone. Most people find that by setting  
aside plenty of time, assembly will go smoothly.  
The included Allen wrenches and following  
tools (not included) are required for assembly:  
• Two adjustable wrenches  
• One rubber mallet  
Before beginning assembly, carefully read the  
following information and instructions:  
• One standard screwdriver  
Assembly requires two people.  
• One Phillips screwdriver  
For help identifying small parts, use the PART  
IDENTIFICATION CHART on page 5.  
• Lubricant, such as grease or petroleum jelly,  
and soapy water.  
Tighten all parts as you assemble them, unless  
instructed to do otherwise.  
Assembly will be more convenient if you have a  
socket set, a set of open-end or closed-end  
wrenches, or a set of ratchet wrenches.  
As you assemble the weight bench, make sure all  
parts are oriented as shown in the drawings.  
1.  
1
Before beginning assembly, make sure you  
26  
understand the information in the box  
above.  
32  
33  
26  
27  
37  
Attach a Wheel (26) to the Stabilizer (2) with an  
M10 x 63mm Button Head Bolt (37), an 15mm x  
43mm Axle (27), an M10 Washer (33), and an  
M10 Nylon Locknut (32). Repeat this step with  
the other Wheel.  
2
2. Press a 50mm x 75mm Inner Cap (25) into the  
Frame (1). Press two 38mm x 100mm Inner Caps  
(45) into the top of the arms on the Frame.  
2
35  
Attach the Frame (1) to the Stabilizer (2) with four  
M10 x 115mm Carriage Bolts (35), four M10  
Washers (33), and four M10 Nylon Locknuts (32).  
45  
25  
1
Arms  
2
33  
33  
32  
32  
6
 
3. Press a 50mm Square Inner Cap (23) into the top  
of the Backrest Frame (3). Press a 50mm Square  
Angled Inner Cap (43) into the bottom of the  
Backrest Frame.  
3
23  
Attach the Adjustment Arm (7) to the Backrest  
Frame (3) with two M12 x 75mm Button Head  
Bolts (36), two M12 Washers (40), and two M12  
Nylon Locknuts (47). Do not tighten the  
Locknuts yet.  
3
40  
47  
40  
7
36  
43  
4. Attach the two Pop Pins (28), two Springs (29),  
two Threaded Collars (30), and two Adjustment  
Knobs (31) to the Frame (1).  
4
Press two 50mm Square Inner Caps (23) into the  
Seat Frame (6). Do not press the indicated Cap  
all the way into the Frame; this Cap will be  
removed later.  
3
Have a second person pull the upper Adjustment  
Knob (31) out as far as it will go. Engage the Pop  
Pin (28) into a hole in the Seat Frame (6).  
7
Do not  
press in  
fully  
23  
6
47  
Lubricate the M12 x 87mm Button Head Bolt (34)  
with grease. With the Adjustment Arm (7) under  
the welded rod, attach the Backrest Frame (3)  
and the Seat Frame (6) to the Frame (1) with the  
Bolt and an M12 Nylon Locknut (47). Do not  
overtighten the Locknut; the Backrest and Seat  
Frames must be able to pivot easily.  
34  
Welded  
Rod  
Upper  
28  
30  
Knob Tube  
29  
23  
30  
28  
29  
Pull the lower Adjustment Knob (31) out as far as  
it will go. Engage the Pop Pin (28) into the  
Adjustment Arm (7). Make sure the Pin is in the  
center of the hole in the Adjustment Arm.  
Tighten the two M12 Nylon Locknuts (not  
shown) used in step 3.  
1
31  
5
3
5. Attach the Backrest (4) to the Backrest Frame (3)  
with four M6 x 16mm Screws (38).  
4
38  
38  
7
 
6. Attach the Seat (5) to the Seat Frame (6) with  
four M6 x 16mm Screws (38).  
6
5
6
38  
38  
7. Press two 40mm x 60mm Inner Caps (46) into  
the Leg Lever (8). Press two 60mm Round  
Bushings (18) into the Leg Lever. Press a 48mm  
Round Inner Cap (19) into the weight tube. Slide  
the Weight Tube Spacer (20) onto the weight  
tube. Make sure the slot fits around the Leg  
Lever.  
7
18  
18  
8
46  
Weight  
Tube  
Slot  
39  
20  
19  
46  
8. Attach a set of Pads (16, 44) to a Pad Brace (17)  
with four M6 x 16mm Screws (38). Make sure  
the Pads and the Pad Brace are oriented as  
shown. Repeat with the other set of Pads and  
the other Pad Brace.  
8
Straight  
Edge  
17  
8
Attach a Pad Brace (17) to the Leg Lever (8) with  
two M10 x 80mm Carriage Bolts (39), two M10  
Washers (33), and two M10 Nylon Locknuts (32).  
Attach the other Pad Brace to the Leg Lever  
(8) in the same manner.  
33  
33  
32  
Straight  
Edge  
32  
44  
16  
38  
39  
17  
38  
9. Press the 50mm Square Bushing (22) into the  
Seat Extension (13). Press the 50mm Square  
Outer Cap (21) onto the Seat Extension.  
9
22  
21  
13  
47  
Lubricate an M12 x 75mm Button Head Bolt (36)  
with grease. Attach the Leg Lever (8) to the Seat  
Extension (13) with the Bolt and an M12 Nylon  
Locknut (47). Do not overtighten the Locknut;  
the Leg Lever must be able to pivot easily.  
8
36  
8
 
10. Wet the ends of the Curl Bar (9) with soapy  
water. Slide the two Long Foam Pads (10) onto  
the Curl Bar. Press two 50mm Round Bushings  
(42) into the Curl Bar.  
10  
10  
10  
Attach the Round Bumper (24) to the Curl Bar (9)  
with an M4 x 16mm Screw (41).  
9
41  
Insert the Curl Bar Pin (14) into the 50mm Round  
Bushings (42). Attach the Curl Bar Pin to the Curl  
Bar (9) with an M4 x 16mm Screw (41).  
24  
42  
14  
41  
11. Attach the Curl Pad (12) to the Curl Post (11) with  
two M6 x 16mm Screws (38).  
11  
12  
11  
12. Make sure that all parts are properly tightened  
before you use the weight bench. The use of  
all remaining parts will be explained in  
38  
ADJUSTMENTS, starting on the next page.  
9
 
ADJUSTMENTS  
This section explains how to adjust the weight bench. Refer to the accompanying exercise guide to see the cor-  
rect form for each exercise.  
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-  
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.  
ADJUSTING THE BACKREST AND SEAT  
To adjust the angle of the Backrest (4), hold onto it  
with one hand and pull the lower Adjustment Knob  
(31) out. Move the Backrest to the desired position.  
Reengage the Knob into the Adjustment Arm (7).  
Make sure that you hold the Knob, to keep your  
hands from being pinched.  
4
Adjust the Seat (5) in the same manner, using the  
upper Adjustment Knob (31).  
7
5
31  
ATTACHING THE LEG LEVER  
6
To use the Leg Lever (8), position the seat in the ele-  
vated position (see ADJUSTING THE BACKREST  
AND SEAT, above). Remove the 50mm Square Inner  
Cap (23) from the Seat Frame (6). Insert the Seat  
Extension (13) into the Seat Frame and secure it with  
a Large Knob (15).  
23  
8
15  
13  
Slide the desired amount of weight (not included)  
onto the weight tube on the Leg Lever (8).  
Replace the 50mm Square Inner Cap (23) into the  
Seat Frame (6) when the Seat Extension (13) is  
removed.  
Weight  
Tube  
ATTACHING THE CURL BAR  
To use the Curl Bar (9), first attach the leg lever to the  
seat frame (see ATTACHING THE LEG LEVER,  
above). Then, pull the Curl Bar Pin (14) out as far as  
it will go. Slide the Curl Bar between the brackets on  
the Leg Lever (8). Engage the Pin into the Leg Lever  
and the Curl Bar.  
9
14  
8
10  
 
ATTACHING THE CURL PAD  
To use the Curl Pad (12), first attach the leg lever to  
the seat frame (see ATTACHING THE LEG LEVER,  
on the previous page). Then, insert the Curl Post (11)  
into the Seat Extension (13) and line up one of the  
three holes with the hole in the Seat Extension.  
Secure the Curl Post at the desired height with a  
Large Knob (15).  
12  
11  
15  
13  
11  
 
EXERCISE GUIDELINES  
THE FOUR BASIC TYPES OF WORKOUTS  
PERSONALIZING YOUR EXERCISE PROGRAM  
Muscle Building  
To increase the size and strength of your muscles,  
Determining the exact length of time for each workout,  
as well as the number of repetitions or sets completed,  
push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo-  
cles will continually adapt and grow as you progres-  
sively increase the intensity of your exercise. You can  
adjust the intensity level of an individual exercise in  
two ways:  
• by changing the amount of resistance used  
• by changing the number of repetitions or sets per-  
formed. (A “repetition” is one complete cycle of an  
exercise, such as one sit-up. A “set” is a series of  
repetitions.)  
ing it during the first few months of your exercise pro-  
gram. You should progress at your own pace and be  
sensitive to your body’s signals. If you experience pain  
or dizziness at any time while exercising, stop immedi-  
ately and begin cooling down. Find out what is wrong  
before continuing. Remember that adequate rest and a  
proper diet are important factors in any exercise pro-  
gram.  
WARMING UP  
The proper amount of resistance for each exercise  
depends upon the individual user. You must gauge  
your limits and select the amount of resistance that is  
Begin each workout with 5 to 10 minutes of stretching  
and light exercise to warm up. Warming up prepares  
right for you. Begin with 3 sets of 8 repetitions for each your body for more strenuous exercise by increasing  
exercise you perform. Rest for 3 minutes after each  
set. When you can complete 3 sets of 12 repetitions  
without difficulty, increase the amount of resistance.  
circulation, raising your body temperature and deliver-  
ing more oxygen to your muscles.  
WORKING OUT  
Toning  
You can tone your muscles by pushing them to a mod- Each workout should include 6 to 10 different exercis-  
erate percentage of their capacity. Select a moderate  
amount of resistance and increase the number of rep-  
etitions in each set. Complete as many sets of 15 to  
20 repetitions as possible without discomfort. Rest for  
1 minute after each set. Work your muscles by com-  
es. Select exercises for every major muscle group,  
emphasizing areas that you want to develop most. To  
give balance and variety to your workouts, vary the  
exercises from session to session.  
pleting more sets rather than by using high amounts of Schedule your workouts for the time of day when your  
resistance.  
energy level is the highest. Each workout should be  
followed by at least one day of rest. Once you find the  
schedule that is right for you, stick with it.  
Weight Loss  
To lose weight, use a low amount of resistance and  
increase the number of repetitions in each set.  
Exercise for 20 to 30 minutes, resting for a maximum  
of 30 seconds between sets.  
EXERCISE FORM  
Maintaining proper form is an essential part of an  
effective exercise program. This requires moving  
through the full range of motion for each exercise, and  
Cross Training  
Cross training is an efficient way to get a complete and moving only the appropriate parts of the body.  
well-balanced fitness program. An example of a bal-  
anced program is:  
• Plan strength training workouts on Monday,  
Wednesday, and Friday.  
• Plan 20 to 30 minutes of aerobic exercise, such as  
running on a treadmill or riding on an elliptical or  
exercise bike, on Tuesday and Thursday.  
Exercising in an uncontrolled manner will leave you  
feeling exhausted. On the exercise guide accompany-  
ing this manual you will find photographs showing the  
correct form for several exercises, and a list of the  
muscles affected. Refer to the muscle chart on the  
next page to find the names of the muscles.  
• Rest from both strength training and aerobic exercise The repetitions in each set should be performed  
for at least one full day each week to give your body  
time to regenerate.  
smoothly and without pausing. The exertion stage of  
each repetition should last about half as long as the  
return stage. Proper breathing is important. Exhale  
during the exertion stage of each repetition and inhale  
The combination of strength training and aerobic exer-  
cise will reshape and strengthen your body, plus devel- during the return stroke. Never hold your breath.  
op your heart and lungs.  
12  
 
Rest for a short period of time after each set. The  
ideal resting periods are:  
• Rest for three minutes after each set for a muscle  
building workout.  
slowly as you stretch and do not bounce. Ease into  
each stretch gradually and go only as far as you can  
without strain. Stretching at the end of each workout  
is an effective way to increase flexibility.  
• Rest for one minute after each set for a toning work-  
out.  
STAYING MOTIVATED  
• Rest for 30 seconds after each set for a weight loss  
workout.  
Plan to spend the first couple of weeks familiarizing  
yourself with the equipment and learning the proper  
form for each exercise.  
For motivation, keep a record of each workout. List the  
date, the exercises performed, the resistance used,  
and the numbers of sets and repetitions completed.  
Record your weight and key body measurements at  
the end of every month. Remember, the key to achiev-  
ing the greatest results is to make exercise a regular  
and enjoyable part of your everyday life.  
COOLING DOWN  
End each workout with 5 to 10 minutes of stretching.  
Include stretches for both your arms and legs. Move  
MUSCLE CHART  
N
A. Sternomastoid (neck)  
A
B
C
B. Pectoralis Major (chest)  
C. Biceps (front of arm)  
D. Obliques (waist)  
E. Brachioradials (forearm)  
F. Hip Flexors (upper thigh)  
G. Abductor (outer thigh)  
H. Quadriceps (front of thigh)  
I. Sartorius (front of thigh)  
J. Tibialis Anterior (front of calf)  
K. Soleus (front of calf)  
O
P
Q
R
D
E
S
F
L
T
L. Rectus Abdominus (stomach)  
M. Adductor (inner thigh)  
N. Trapezius (upper back)  
O. Rhomboideus (upper back)  
P. Deltoid (shoulder)  
G
M
H
I
U
V
Q. Triceps (back of arm)  
R. Latissimus Dorsi (mid back)  
S. Spinae Erectors (lower back)  
T. Gluteus Medius (hip)  
J
K
W
U. Gluteus Maximus (buttocks)  
V. Hamstring (back of leg)  
W. Gastrocnemius (back of calf)  
13  
 
PART LIST—Model No. NTB14920  
R0303A  
Key No. Qty.  
Description  
Key No. Qty.  
Description  
1
2
3
4
5
6
7
8
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2
2
2
2
1
1
1
1
3
1
1
2
2
2
2
Frame  
Stabilizer  
Backrest Frame  
Backrest  
Seat  
Seat Frame  
Adjustment Arm  
Leg Lever  
Curl Bar  
Long Foam Pad  
Curl Post  
Curl Pad  
Seat Extension  
Curl Bar Pin  
Large Knob  
Left Leg Pad  
Pad Brace  
60mm Round Bushing  
48mm Round Inner Cap  
Weight Tube Spacer  
50mm Square Outer Cap  
50mm Square Bushing  
50mm Square Inner Cap  
Round Bumper  
50mm x 75mm Inner Cap  
Wheel  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
#
2
2
10  
10  
1
4
3
2
18  
4
2
2
2
1
2
2
2
4
2
2
2
2
1
2
1
1
Threaded Collar  
Adjustment Knob  
M10 Nylon Locknut  
M10 Washer  
M12 x 87mm Button Head Bolt  
M10 x 115mm Carriage Bolt  
M12 x 75mm Button Head Bolt  
M10 x 63mm Button Head Bolt  
M6 x 16mm Screw  
M10 x 80mm Carriage Bolt  
M12 Washer  
M4 x 16mm Screw  
50mm Round Bushing  
50mm Square Angled Inner Cap  
Right Leg Pad  
38mm x 100mm Inner Cap  
40mm x 60mm Inner Cap  
M12 Nylon Locknut  
Small Threaded Collar  
Adjustment Pin  
Short Spring  
M5 x 11mm Screw  
Spring Clip  
Spring Clip Cap  
User’s Manual  
Exercise Guide  
Grease Packet  
M8 Allen Wrench  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
#
#
#
#
15mm x 43mm Axle  
Pop Pin  
Spring  
1
1
1
M6 Allen Wrench  
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover  
of this manual for information about ordering replacement parts.  
14  
 
EXPLODED DRAWING—Model No. NTB14920  
R0303A  
10  
18  
12  
44  
38  
39  
32  
18  
33  
17  
46  
41  
38  
9
24  
41  
16  
11  
8
39  
42  
48  
51  
19  
46  
42  
20  
38  
15  
14  
4
38  
22  
23  
50  
49  
38  
47  
38  
13  
17  
36  
49  
21  
44  
3
33  
50  
40  
38  
47  
48  
15  
16  
32  
7
51  
5
36  
43  
35  
23  
6
47  
25  
23  
26  
33  
27  
33  
45  
38  
37  
34  
29  
32  
32  
27  
38  
26  
37  
30  
31  
28  
33  
32  
33  
32  
29  
30  
1
52  
53  
2
15  
 
ORDERING REPLACEMENT PARTS  
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-825-2588, Monday  
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-  
pared to give the following information:  
1. The MODEL NUMBER of the product (NTB14920)  
2. The NAME of the product (NordicTrack® STRENGTH COMBINATION BENCH weight bench)  
3. The SERIAL NUMBER of the product (see the front cover of this manual)  
4. The KEY NUMBER and DESCRIPTION of the part(s) (see pages 14 and 15 of this manual)  
LIMITED WARRANTY  
WHAT IS COVERED—The entire NordicTrack® STRENGTH COMBINATION BENCH weight bench (“Product”) is warranted to be  
free of all defects in material and workmanship.  
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.  
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the product frame for five years after the date of pur-  
chase. ICON warrants all other parts for one year after the date of purchase. Labor is covered for one year.  
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or component, pro-  
viding the repairs are authorized by ICON first and are performed by an ICON trained and authorized service provider, or, at our  
option, we will replace the Product.  
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, improper  
assembly or installation, alterations, modifications without our written authorization or by failure on your part to use, operate, and  
maintain as set out in your User’s Manual (“Manual”).  
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the Product as spec-  
ified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of the defect; as instruct-  
ed, return any defected part for replacement or, if necessary, the entire product, for repair.  
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product. Remember to do the  
periodic maintenance requirements specified in the Manual to assure proper operation and your continued satisfaction.  
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-825-2588 and tell them your name  
and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary, arrange for serv-  
ice where your Product is located or advise you how to ship the Product for service. Before shipping, always obtain a Return  
Authorization Number (RA No.) from our Customer Service Department; securely pack your Product (save the original shipping car-  
ton if possible); put the RA No. on the outside of the carton and insure the product. Include a letter explaining the product or prob-  
lem and a copy of your proof of purchase if you believe the service is covered by warranty.  
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or per-  
formance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoy-  
ment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the  
exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.  
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness  
for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow limitations on how  
long an implied warranty lasts. Accordingly, the above limitation may not apply to you.  
No one is authorized to change, modify or extend the terms of this limited warranty. This warranty gives you specific legal rights and  
you may have other rights which vary from state to state.  
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813  
Part No. 193412 R0303A  
Printed in China © 2003 ICON Health & Fitness, Inc.  
 

Miele Freezer K 1803 Vi User Manual
Mr Heater Patio Heater SRPH02S User Manual
Multiquip Portable Generator DCA400SSI User Manual
National Instruments Network Card TPC 2012 User Manual
NextBase DVD Player SDV77 BD User Manual
Nortel Networks Switch 50 Series User Manual
Oneida Air Systems Dust Collector Super Dust Gorilla User Manual
Optimus Speaker PRO SWS300 User Manual
Panasonic Answering Machine KX TG1843AL User Manual
Parkside Cordless Saw PHKS 66 User Manual