New Holland H8000 Series
Self-Propelled Windrower Specifications
H8040 H8040 Prairie Special H8060 H8080
MODEL
ENGINE
H8040
H8060
H8080
H8040 PRAIRIE SPECIAL
New Holland 4-cylinder
274 cu. in. (4.5 L)
New Holland 6-cylinder
411 cu. in. (6.7 L)
New Holland 6-cylinder
411 cu. in. (6.7 L)
..........................................................................................................................Turbocharged with air-to-air intercooler....................................................................................
Rated horsepower (kW)*
Fuel injection pump
126 (94) @ 2,300 rpm
Mechanical
190 (142) @ 2,200 rpm
Electronically controlled
high pressure common rail
2, 12-Volt 650 CCA / 150 amp
226 (168) @ 2,200 rpm
Electronically controlled
high pressure common rail
2, 12-Volt 650 CCA / 150 amp
Batteries / alternator
1, 12-Volt 925 CCA / 150 amp
Fuel capacity, gal. (L) .......................................................................................................................120 (454) ...........................................................................................................
Rotary radiator screen cleaner..........................................................................................................Standard............................................................................................................
TRANSMISSION.....................................................................................................................Dual range hydrostatic.................................................................................................
Final drive ...........................................................................................................................Double reduction planetary..............................................................................................
Steering...........................................................................................................................................Hydrostatic..........................................................................................................
Speed range, mph (kph)
0-10.6 (0-17) working**
0-15.8 (0-25.4) - road**
0-12.5 (0 - 20) - working***
0-18 (0 - 29) - road***
0-12.5 (0 - 20) - working***
0-18 (0 - 29) - road***
LENGTH, with header
283.1 (7192) with HS Series
269.5 (6847) with 2355
269.5 (6847) with 2358
Less header and lift arms, in. (mm)............................................................................................205.2 (5213).........................................................................................................
Height, in. (mm)
134.1 (3415)**
136.1 (3456)***
136.1 (3456)***
Wheelbase, in. (mm).......................................................................................................................138 (3494) ..........................................................................................................
Front tread width, in (mm)
127 (3225)**
130.2 (3308)***
130.2 (3308)***
Rear tread width (adjustable), in. (mm)..........................................................................90-105-120 (2286-2667-3048) ..........................................................................................
Rear axle suspension.........................................................................................................................Optional.............................................................................................................
Tractor weight, lbs. (kg)
10,745 (4874)**
11,365 (5155)***
11,365 (5155)***
Rear axle tires..............................................................................................................................14L x 16.1 8PR.......................................................................................................
Rear axle ground clearance
35.7 (908)
with 18.4 x 26 front tires
35.7 (908)
with 18.4 x 26 front tires
38.8 (986)
with 23.1 x 26 front tires
Header drive......................................................................................................................................Hydraulic............................................................................................................
Header flotation
Hydraulic (in-cab adjustable)
.......................Independent hydraulic flotation (flotation weight at each end
of header independently controlled from cab)............................................
HEADER TILT
Hydraulic...........................................................................................................................................Standard............................................................................................................
Header power reverser......................................................................................................................Standard............................................................................................................
Adjustable windrow shields ..............................................................................................................Standard............................................................................................................
In-cab windrow-width adjustment.....................................................................................................Optional.............................................................................................................
Single lever header
Transport lock system ....................................................................................................................Standard............................................................................................................
CAB ....................................................................................................................................Deluxe, curved tinted glass..............................................................................................
Cab suspension.................................................................................................................................Standard............................................................................................................
Cab air filtration............................................................................................Dual: 1 external air filter and 1 in-cab recirculation filter.......................................................................
Seat ...............................................................................................Deluxe air suspension seat with fore/aft lumbar adjuster, ride dampening ........................................................
Instructor seat...................................................................................................................................Standard............................................................................................................
*Manufacturer's rating per ECE R120 / ISO 14396 **with 18.4 x 26 tires ***with 23.1 x 26 tires
HEADERS
Sickle Hay Headers
12HS* 14HS
12 ft., 3 in. 14 ft., 3 in. 16 ft., 3 in. 18 ft., 3 in.
Disc Hay Header
Draper Headers
16HS
18HS
720HD** 750HD
770HD
21HB** 25HB
30HB
30 ft.
36HB
36 ft.
13 ft.
15 ft., 5 in. 18 ft.
21 ft.
25 ft.
H8040
H8060
H8080
•
•
•
•
•
•
•
•
•
•
•
•
NA
•
•
NA
•
•
NA
NA
•
•
•
•
•
•
•
•
•
•
•
•
•
*12-foot header requires 16.9 x 28 drive tires **not compatable with 23.1 x 26 drive tires
Page 1of 5
New Holland
®
Discbine Disc Header Specifications
720HD 750HD 750HD Specialty 770HD
MODEL
720HD
750HD
750HD SPECIALTY
H8060/H8080
770HD
H8080
WINDROWER MODEL
H8060/H8080
H8060/H8080
Header drive........................................................................................Hydrostatically driven header with dual hydraulic header drive motors........................................................
Cutting width, ft. in. (m)
Overall width, ft. in. (m)
Weight, lbs. (kg)
13' (3.96)
13' 3" (4.04)
3010 (1365)
15' 4" (4.7)
15' 6" (4.75)
4680 (2123)
15' 4" (4.7)
15' 6" (4.75)
3305 (1499)
17' 11" (5.45)
18' 1" (5.51)
4890 (2218)
MODULAR DISC CUTTERBAR
Number of discs
10
12
12
14
Maximum disc speed, rpm.....................................................................................................................3000............................................................................................................
Number of reversible,
swing-away knives
20 (2 per disc)
187 (301)
24 (2 per disc)
187 (301)
24 (2 per disc)
187 (301)
28 (2 per disc)
187 (301)
Knife tip speed, mph (kph)
Flotation ....................................................................................................................Hydraulic adjustment from windrower cab..............................................................................
Cutting angle and height..............................................................Standard hydraulic control, from 2 to 12 degrees (minimum: 0.6 in. [15 mm]).................................................
with standard skid shoes*
Transport height—
bottom of skid shoes, in. (mm)
24.5 (622)
29.6 (754)
29.6 (754)
29.6 (754)
Hood liner.................................................................................................................High density, impact-resistant polyethylene.............................................................................
CONDITIONER
Type
Chevron-design, intermeshing
molded rubber rolls
102 (2.6)
Chevron-design, intermeshing
molded rubber rolls
102 (2.6)
NA
Chevron-design, intermeshing
molded rubber rolls
102 (2.6)
Length, in. (m)
Roll speed, rpm
Roll pressure
NA
NA
NA
920
923
923
Torsion-bar roll pressure system Torsion-bar roll pressure system
Torsion-bar roll pressure system
adjusts with a single crank,
rolls separate automatically
“on the go” to allow thick
material to pass
adjusts with a single crank,
rolls separate automatically
“on the go” to allow thick
material to pass
adjusts with a single crank,
rolls separate automatically
“on the go” to allow thick
material to pass
Roll gap
Windrow/swath width, in. (mm)
Adjustable stop-bolt
38–96 (965–2438)
Adjustable stop-bolt
38–96 (965–2438)
NA
Adjustable stop-bolt
38–96 (965–2438)
60 (1524), 83 (2108)
or 100 (2540)
AUGER
Type
NA
NA
NA
Floating
20 (508)
5 (127)
Floating
20 (508)
Tapered, 7 (178) to 1 (25)
Floating
20 (508)
7 (178)
Maximum diameter, in. (mm)
Flighting depth, in. (mm)
*with 18.4 x 26 tires **with 23.1 x 26 tires
OPTIONS (field-installed):
• Crop dividers
• High-contact chevron conditioning rolls
• High stubble kit
• Corner marker kit
• Slatted-steel conditioning bundle
• Gauge wheels
• Push bar
• Closure kit
Page 3of 5
New Holland
HB Series Draper Header Specifications
21HB 25HB 30HB 36HB
MODEL
VERSIONS AVAILABLE
21HB
25HB
30HB
36HB
Single-knife drive, standard deck
Single-knife drive, double swath
Double-knife drive, standard deck
Double-knife drive, double swath
x
x
x
x
x
x
x
x
x
x
x
HEADER
Cutting width, ft. (m)
21 (6.4)
3880 (1760)
1.0 (25)*
NA
25 (7.6)
4135 (1875)
1.0 (25)*
Optional
30 (9.1)
5021 (2278)
1.0 (25)
36 (11)
5434 (2465)
1.0 (25)*
Standard
Approximate weight (includes reel), lbs. (kg)
Cutting height (minimum), in. (mm)
Castering gauge wheels
Standard deck center windrow
width opening, in. (m)
Double swath center windrow
width opening, in. (m)
Standard
NA
80 (2.03)
80 (2.03)
80 (2.03)
50 (1.27)
56 (1.42)
56 (1.42)
56 (1.42)
Slow speed header transport kit..............................................................................................................Standard.....................................................................................................
Transport height, in. (m) ................................................................................................40 (1.02) from tip of guards to ground)* ...........................................................................
CUTTERBAR
Cutting system............................................................................Choice of New Holland dual-knife system or Schumacher single-or dual-knife system........................................
Knife drive...................................................................................................Schumacher hydraulically-driven, planetary-reduction sickle drive........................................................
Sickles
2
1 or 2
1 or 2
2
Sickle speed - strokes per minute...............................................................................................................1400 ........................................................................................................
Sickle stroke, in. (mm) ............................................................................................................................3.31 (84).....................................................................................................
Hay guards...............................................................................................................................................Standard.....................................................................................................
REELS
Type
Steel
..........Pick-up with steel or plastic fingers ..........
20–48 rpm 20–48 rpm
Plastic fingers
20–48 rpm
Speed range
20–48 rpm
Drive.........................................................................................................................Direct hydraulic drive w/ 45 cu. in. (.74 L) motor ....................................................................
Hydraulic reel fore / aft adjustment
Standard
Optional
Optional
Standard
DRAPER BELTS
Belt width and construction................................42 in. (1.07 m) rubberized polyester belt with fiberglass reinforcement, tie bar end connection and molded V-Guide................
Speed range, ft. (m)......................................................................................................................0 - 705 (215) / minute ..........................................................................................
In cab canvas-speed control....................................................................................................................Standard.....................................................................................................
Angle..................................................................................................................................................10 to 20 degrees...............................................................................................
Double swath shift means.......................................................................................................................Hydraulic.....................................................................................................
* with 18.4 x 26 drive tires
OPTIONS (factory-installed)
• Poly cutterbar skid plates
• End-gauge wheels
• Castering gauge wheels for 25HB
• Cross auger kit
Page 4of 5
New Holland SP Windrower Dual Windrow
Merger Attachment Specifications
GENERAL INFORMATION
Mechanical design
Laterally-mounted, draper-belt conveyor; folds up under windrower belly frame when not in use, allowing single windrow or swath formation.
Merger folds down and forward (further forward at the left end) when deployed for merging application.
Movable deflector allows operator to control distance crop is thrown.
Crop delivery direction
Windrower compatibility
Windrower software requirement
Header compatibility
Right side, behind right front tire
Tier II, 6-cylinder models (non-draper) and all Tier III, 6-cylinder models (except with dealer-installed draper ready)
7.1 or higher*
15.5' and 18' disc headers with conditioning system
Belt construction
Single ply w/two ply edges; vulcanized endless construction w/vee-guide tracking rib on inner surface and lateral
cleats on the outer surface to positively move material
Belt tensioning
Belt tracking
Adjustable spring tension to minimized shock loading
Eye bolt adjustment at front end of driver roll
Merger conveyor flotation
Table can float upward to minimize damage in the event of an obstruction or obstacle
HYDRAULIC SYSTEM
Raise/lower-deflector- belt drive
Pump type
Pump capacity @ rated speed, gpm
Relief Pressure, psi (bar)
Common system utilizing optional windrower-mounted auxiliary hydraulic system
Windrower-mounted, fixed-displacement
Tier II - 11.3 gpm (42.8 lpm); Tier III - 15.1 gpm (57.2 lpm)
2000 (137.9)
Belt drive type
Fixed-displacement gear motor drive through #50 chain
1.53 (25)
7 - 13 (11.3 - 21)
2.5 (63.5) diameter, double-acting w/mechanical transport lock
1.5 (38.1) diameter, double-acting
Motor displacement, cu. in. (cu. cm)
Conveyor belt speed range, mph (kph)
Raise/lower cylinder, in. (mm)
Side deflector cylinder, in. (mm)
SIDE DEFLECTOR
Design
Mounting frame
Top-hinged, formed steel deflector w/plastic lower extension to protect the deflector from damage in the event of hitting an obstruction or high-centering
Horizontal (manually) adjustable to accommodate two sizes of headers and operator preference on windrow shape and width
OPERATOR CONTROLS
Raise/lower
Belt speed
Propulsion handle-mounted button control- fully up or fully down
Right-hand console mounted, two-action On/Off switch and variable speed toggle switch
Propulsion handle-mounted rocker-switch, variable position control
Side deflector
DIMENSIONS
Conveyor frame length, in. (mm)
Conveyor frame width, in. (mm)
Conveyor belt width, in. (mm)
Conveyor belt length, in. (mm)
Belt roller diameter, in. (mm)
77.4 (1966.2)
89 (2260.5)
42 (1066.8)
84.6 (2150) center to center of rolls
4 (101.6)
Ground clearance, operating, in. (mm)
Ground clearance, transport, in. (mm)
Adjustable; 5 (127) recommended (continuous ground contact is not intended)
28 (711)
WEIGHT (merger attachment only; does not include aux. hyd. kit)
Shipping, lb. (kg)
Operating, lb. (kg)
1125 (510.3)
976 (443)
LUBRICATION
Grease points
Drive chain
50 hr. lube interval at 3 zerks
10 hr or daily interval; lube belt drive chain w/motor oil
OTHER REQUIREMENTS
Auxiliary hydraulic drive kit
Select Tier II (dealer installed) or Tier III kit (factory- or dealer-installed option)
* 7.1 is assumed to be the level that will be installed concurrent w/MY09 Job 1 at this time (3/08). MY08 units have 7.0 installed. Special software was provided for each of the pre-build units.
Software on those units need not be replaced, unless other issues would necessitate it.
Design, materials and/or specifications are subject to
change without notice and without liability therefor.
Specifications are applicable to units sold in Canada, the
United States, its territories and possessions, and may
vary outside these areas.
Safety begins with a thorough understanding of
the equipment. Always make sure you and
your operators read the Operator’s Manual
before using the equipment. Pay close
attention to all safety and operating
decals and never operate machinery
without all shields, protective devices
and structures in place.
© 2008 CNH America LLC
New Holland is a registered trademark of CNH America LLC.
Page 5of 5
|