Nady Systems Microphone DKW1 User Manual

DKW-1 WIRELESS MICROPHONE SYSTEM  
OPERATING INSTRUCTIONS  
OPERATING INSTRUCTIONS  
Congratulations on your purchase. The Nady DKW-1 is the perfect entry level professional wireless, and delivers clear,  
transparent audio for a variety of singing and speech applications. Although offered at a breakthrough new low price for a  
professional wireless, this system is loaded with features:  
High-band VHF (170-216 MHz) operation for interference-free performance  
Companding circuitry for a wide dynamic range (no overloading for loud inputs or background hiss during quiet use)  
Full frequency response from 40 –20,000 Hz  
250 ft. typical, up to 500 ft. line-of-sight operating range  
Choice of transmitters:  
• WHT-14 Handheld mic with a powerful neodymium cartridge that delivers unsurpassed audio, low handling  
noise and enhanced feedback rejection  
• WLT-14 Bodypack for lavalier/lapel headworn mic  
DKW-1receiver with unique vertical space-saving mini portable design and jumbo LED indicators for power ON,  
transmitter ON and audio peak. Special added circuitry eliminates transmitter ON/OFF"pop" noise.  
OPERATION  
A. DKW-1 RECEIVER  
1. Plug the AC/DC adapter (provided) into the 12VDC INPUT JACK (3)  
on the back of the receiver. Then plug the power supply into an AC  
outlet. Slide the POWER SWITCH (1) to the ON position. The  
POWER ON LED (6) will now light and the receiver is operational.  
2. Rotate and extend ANTENNA (7) to the full vertical position.  
3. The 1/4” AUDIO OUTPUT JACK (2) provides a fixed, unbalanced  
MIC level audio output for connection to your mixer with the 3 ft.  
1/4” to 1/4” cord supplied. As when making any connection, make sure the  
mixing boards volume is at the minimum level before plugging in the  
receiver to avoid possible sound system damage.  
7
4
5
2
3
6
1
B. WHT-14 HANDHELD MIC TRANSMITTER  
1. Unscrew the BATTERY COMPARTMENT COVER (8) and remove,  
exposing the BATTERY HOLDER (11). Insert a fresh 9V BATTERY (9),  
observing correct polarity as marked, and screw the cover back on to the  
microphone. To ensure proper battery contact, the cover must be screwed  
on completely.  
DKW-1  
2. Turn on the WHT-14 by sliding the OFF/MUTE/ON SWITCH (10)  
to the MUTE position (transmitter on, audio muted) or the ON position  
(transmitter and audio both on). The BATTERY INDICATOR LED (12)  
will give a single quick flash, indicating usable battery strength. In the case of  
a dead or low battery, the LED will either not go on at all or will stay on  
continuously, indicating that the battery should be replaced with a fresh one.  
3. The microphone is now ready to use. The TRANSMITTER SIGNAL  
RECEIVED LED (5) on the DKW-1 receiver should now be lit. When ready  
to speak, slide the transmitter switch to the ON position and adjust the mixing  
board volume level as needed. The AUDIO PEAK LED (4) will flicker on the  
receiver with the audio peaks of the microphone input. This is normal. If the  
indicator lights continuously, it means the signal is too loud and there is the  
possibility of overload distortion. Back off from the microphone until the  
indicator only flickers on peaks.[Note: Observe care in selecting P.A. volume,  
transmitter location and speaker placement so that acoustic feedback (howling  
or screeching) will be avoided. See also Section C 3 below.]  
12  
10  
8
WHT-14  
8
12  
10  
11  
9
 

Miele Cooktop KM83 2 User Manual
Miele Microwave Oven 09 924 540 User Manual
Milwaukee Power Hammer 2416 20 User Manual
MTD Yard Vacuum 241 660 000 User Manual
Multiquip Portable Generator DCA400 User Manual
Murphy Network Card Series 1501 User Manual
NAD Stereo Receiver T744 User Manual
National Instruments Car Stereo System 320571 01 User Manual
Nikon Camera Lens 18 55mm f 35 56G User Manual
Panasonic Photo Printer AL TA10U User Manual