NETGEAR Switch GS108A User Manual

Technical Support  
Please refer to the Support Information card that shipped with your product.  
expert technical support and timely notices of product and software upgrades.  
NETGEAR, INC.  
Support Information  
Phone: 1-888-NETGEAR (For US & Canada only) - 24x7 phone support  
For other countries see your Support Information card.  
E-mail: [email protected] (24x7 online support)  
©2006 NETGEAR, Inc. NETGEAR, the Netgear logo, ProSafe, The Gear Guy and Everybody's Connecting are  
trademarks or registered trademarks of Netgear, Inc. in the United States and/or other countries. Microsoft and  
Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. Other brand  
and product names are trademarks or registered trademarks of their respective holders. Information is subject to change  
without notice. All rights reserved.  
February 2006  
2 0 1 - 1 0 8 1 8 - 0 1  
 
Introduction  
®
The NETGEAR ProSafe 8-Port Gigabit Ethernet Switch Model GS108A provides you with a  
low-cost, reliable, high-performance switch to connect up to eight different Ethernet-enabled  
devices (such as computers, file servers and routers) at blazing Gigabit Ethernet speeds.  
ll
Model GS108A  
ProSafe 8-Port  
The GS108A Gigabit Ethernet Switch enables you to build a small network that gives you 10,  
100, or 1000 Mbps access to other devices on the network. It provides a full, dedicated 1000  
(or 100, or 10 Mbps) connection between two devices. If a device has full-duplex capability,  
the GS108A switch provides a 2000 Mbps (or 200, or 20 Mbps) connection. If your network  
is configured to support Jumbo Frames, the GS108A will forward them, as well as honoring  
priority tags at both the layer 2 and layer 3 level. This means the GS108A can instantly move  
even very large files across your network. As an added benefit, this switch works with both  
Windows and Macintosh computers.  
Ethernet cables come as either straight-through or crossover cables—depending on whether  
you’re connecting to a device (computer, server, or printer) or networking equipment (hub,  
switch, or router). With the Auto Uplink™ feature, you don’t have to worry about which one  
you use. Each port on the GS108A switch automatically configures itself correctly when you  
plug in a device’s cable.  
If you have a problem with your switch, NETGEAR offers technical support 24 hours a day  
and by phone (see the provided support information card for phone numbers).  
Installation Overview  
Estimated Time: 5–10 minutes  
1. Unpack the box and verify the contents.  
2. Prepare to install the switch.  
3. Install the switch and connect the other devices.  
 
Unpack the Box and Verify  
the Contents  
1
t
Model GS108A ProSafe 8-Port 10/100/1000 Mbps  
Gigabit Ethernet Switch  
Wall-mount  
hardware  
Warranty/support information card  
Power adapter  
When you open the box, verify that you received everything. The package includes:  
ProSafe 8-Port Gigabit Ethernet Switch GS108A  
AC power adapter  
Wall-mounting screws  
GS108A Installation Guide (this document)  
Warranty/support information card  
If you don’t have everything listed above, see the support information card for contact  
information. If you’re missing the support information card itself, get contact information at  
www.NETGEAR.com in the Technical Support section.  
 
Prepare to Install the Switch  
2
Decide where you want to place the switch. Find a flat horizontal surface — such as a table,  
desk or shelf. The switch comes with wall-mounting screws. You’re welcome to use the screws if  
you want to hang the switch in an open space on a wall.  
Make sure the selected location is:  
Not in direct sunlight or near a heater or heating vent.  
Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all  
sides of the switch.  
Well ventilated (especially if it is in a closet).  
Also, you’ll need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each device  
you want to connect to the switch. Each Ethernet cable must be less than 328 feet (100 meters).  
 
Install the Switch and Connect the  
Other Devices  
3
Apple G4  
PC with  
GA311  
Server with GA311  
Adapter  
DSL  
modem  
Adapter  
LOCAL  
10/100M  
8
7
6
5
4
3
2
1
INTERNET  
12VDC 1.2A  
OFF  
ON  
GS108A ProSafe 8-Port 10/100/1000 Mbps  
Gigabit Ethernet Switch  
FVS318 ProSafe VPN Firewall  
1. Place the switch on a flat surface or hook onto the screws.  
2. For each device, insert one end of an Ethernet cable into the port in the device and insert  
the other end into one of the Ethernet ports on the switch.  
3. Connect the power adapter’s cord into the back of the switch and then plug the adapter  
into a power source (such as a wall socket or power strip).  
Both=1000M  
The Power light should light up.  
100M  
LED  
10M  
LED  
Power  
The corresponding Link LED for each  
connected and powered device should  
light when connected and flash when  
activity occurs. If the connection is 10  
Mbps or 100 Mbps, one of the LEDs  
in the RJ-45 jack will light up. If the  
GS108  
GS108A ProSafe 8-Port 10/100/1000 Mbps  
Gigabit Ethernet Switch  
connection is 1000 Mbps, then both of the LED's in the RJ-45 jack will light up.  
Note: If any light doesn’t operate as indicated, go to the Troubleshooting section.  
 
Troubleshooting  
The Power light is not lit  
The switch has no power.  
Make sure the power cord is properly connected to the switch.  
Make sure the power adapter is properly connected to a functioning power outlet. If it’s in  
a power strip, make sure the power strip is turned on. If the socket is controlled by a light  
switch, make sure the switch is in the on position.  
Make sure you are using the NETGEAR power adapter supplied with your switch.  
The Port number light is not lit for a connected device or  
stays on continuously  
There’s a hardware connection problem.  
Make sure the cable connectors are securely plugged in at the switch and the device.  
Make sure the connected device is turned on.  
If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card  
or adapter is installed correctly and is working.  
Make sure the cable is less than 328 feet (100 meters).  
Technical Specifications  
Standards Compatibility:  
IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u 100BASE-TX Fast Ethernet,  
1000BASE-T Gigabit Ethernet.  
IEEE 802.3x Flow Control; Jumbo frame 9K, IEEE 802.1p priority, DSCP  
priority, compatible with Windows®, Mac® OS, NetWare®, Linux®  
Network Interface:  
Power:  
RJ-45 connector for 10BASE-T, 100BASE-TX, or 1000BASE-T Ethernet interface  
12 W max and 12 V @ 1A DC input  
Physical Dimensions:  
Weight:  
W: 158 mm (6.22") D: 101 mm (3.98") H: 27mm (1.0")  
0.518 kg (1.14 lbs)  
Operating Temperature:  
Operating Humidity:  
0 to 50° C (32 to 122° F)  
10% t0 90% relative humidity, non-condensing  
Electromagnetic Compliance: CE mark, Commercial; FCC Part 15, Class A; EN 55 022 (CISPR 22), C-Tick  
Safety Agency Approvals for  
the Power Adapter:  
CE mark, Commercial UL listed (UL 1950), C-Tick  
Performance Specifications  
Frame Filter Rate:  
14,800 frames/sec max for 10M port / 148,800 frames/sec max for  
100M port/1,488,000 frames/sec for 1000M port  
Frame Forward Rate:  
14,800 frames/sec max for 10M port / 148,800 frames/sec max for  
100M port / 1,488,000 frames/sec max for 1000M port  
Network Latency:  
(using 64-byte packets)  
100 Mbps to 100 Mbps: 40 µs max  
1000 Mbps to 1000 Mbps: 10 µs max  
Address Database Size:  
Addressing:  
Packet Buffer Memory:  
4000 MAC addresses  
48-bit MAC address  
128 KB Embedded  
 
Statement of Conditions  
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to  
make changes to the product described in this document without notice.  
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit  
layout(s) described herein.  
Certificate of the Manufacturer/Importer  
It is hereby certified that the NETGEAR Model GS108 Gigabit Ethernet Switch has been suppressed in accordance  
with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment  
(for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions.  
Please refer to the notes in the operating instructions.  
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and  
has been granted the right to test the series for compliance with the regulations.  
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:  
This device may not cause harmful interference.  
This device must accept any interference received, including interference that may cause undesired operation.  
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
EN 55 022 Declaration of Conformance  
This is to certify that the NETGEAR Model GS108 Gigabit Ethernet Switch is shielded against the generation of radio  
interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared  
by the application of EN 55 022 Class A (CISPR 22).  
Canadian Department of Communications Radio Interference Regulations  
This digital apparatus (NETGEAR Model GS108 Gigabit Ethernet Switch) does not exceed the Class A limits for  
radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian  
Department of Communications.  
Règlement sur le brouillage radioélectrique du ministère des Communications  
Cet appareil numérique (NETGEAR Model GS108 Gigabit Ethernet Switch) respecte les limites de bruits  
radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique  
du ministère des Communications du Canada.  
 

Milwaukee Drill 5378 20 User Manual
Moyer Diebel Dishwasher 301HT User Manual
MTD Automobile Accessories 143 660 User Manual
Murray Lawn Mower 465600x8A User Manual
Niles Audio Stereo Receiver ZR 8630AVZR 8630AV User Manual
Oki Switch BISM2 User Manual
Omega Thermometer OSP SERIES User Manual
Optima Company Home Theater System HD131XE User Manual
Oricom Cordless Telephone eco50 User Manual
Pacific Digital Musical Instrument DrumXtreme User Manual