Multi Link Garage Door Opener SD 300M User Manual

MultiLink®  
MINI GARAGE DOOR REMOTE  
WITH FLASH LIGHT  
MODEL : SD-300M  
1. PROGRAMMING YOUR NEW TRANSMITTER FOR  
STANLEY® / MULTI-CODE® OPENERS  
5. WARNING  
If this transmitter triggers other garage doors in your neighborhood,  
change all your transmitters and receiver to a new code setting.  
Thank you for your purchase of the MultiLink® garage door remote control,  
Model SD-300M. This remote is designed to work with Stanley®/ Multi-Code®  
garage door opener w ith DIP switches. Please follow the details instruc tions  
below to setup the new transmitter to work with your existing opener.  
DO NOT let children use the garage door  
transmitter without adult supervision.  
Children can injure themselves or others  
by the garage door.  
1. Open the case with a coin.  
6. FCC  
2. For code setting:  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and (2) This device must accept any interference  
received, including interference that may cause undesired operation.  
Remove the battery cover on your Stanley®/ Multi-Code® transmitter or  
the cover on receiver located on your garage door opener. Match the  
DIP switches on the MultiLink® transmitter to already existing transmitter  
or receiver DIP switches.  
WARNING:  
Changes or modifications to this unit not expressly approved by the party responsible for compliance could  
void the user’s authority to operate the equipment.  
NOTE:  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses and can radiate radio frequency  
energy and, if not installed and used in accordance with the instructions, may cause harmful interference  
to radio communications.  
Dip Switch  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does  
causeharmful interference to radio or television reception, which can be determined by turning the equipment  
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
Tact  
Switch  
- Reorient or relocate the receiving antenna.  
Red  
LED  
- Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
- Consult the dealer or an experienced radio/TV technician for help.  
7. WARRANTY  
Dip Switch  
If, within one year from date of purchase, this product should become defective  
(except battery), due to faulty workmanship or materials, it will be repaired or  
replaced, without charge. Proof of purchase and a Return Authorization are required.  
3. Test the transmitter by pressing onto the switch (see figure), the  
red LED should come on and it should activate the garage door.  
Close the case firmly.  
8. CUSTOMER SERVICE  
2. TROUBLESHOOTING  
Skylink will not be held liable or responsible for any misuse or application of this  
product other than for its intended use.  
If the garage door cannot be activated, check the followings:  
If you would like to order Skylink’s products or have difficulty getting them to  
work, please :  
- Ensure the DIP switch setting on the MutliLink® is identical to the existing  
Stanley®/ Multi-Code® remote.  
- Ensure all the DIP switches are pushed either all the way to the top, or  
bottom, not somewhere in the middle  
- The red light LED should come on when the button is pressed, if not,  
check the battery and its polarity, ensure it is inserted properly.  
If you would like to order Skylink’s products or have difficulty getting them to work,  
please :  
2. email us at [email protected]m, or  
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.  
Fax 1-800-286-1320  
3. OPERATION  
Press and hold the plastic case  
where it marks “PRESS” to  
®
activate the flash light.  
Garage Door  
Button  
Press the garage door opener  
button will activate your garage  
door.  
4. BATTERY  
One 3 volt Lithium type (CR2032)  
battery is included.  
Replacing the battery.  
1. Open the case with a corn.  
2. Slide the old battery away from  
Positive "+"  
CUSTOMER SERVICE  
Up  
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3  
P/N 101A370-001  
© 2005 SKYLINK GROUP  
the battery holder.  
3. Slide in the new battery with the  
positive (+) side facing up.  
4. Firmly close the case.  
® are registered trademarks of their respective corporations  
 

Miele Burner CS 1112 E User Manual
Muratec Fax Machine M840 User Manual
Nilfisk Advance America Vacuum Cleaner BR1100S User Manual
Nilfisk ALTO Pressure Washer 2 21 XT User Manual
Nortel Networks Network Card Installing Media Dependent Adapters User Manual
Omnimount Projector Accessories PMC AL User Manual
Ozaki Worldwide Speaker DT1012 User Manual
Panasonic All in One Printer KX MB2000HX User Manual
Panasonic Electric Shaver ES RW30 S User Manual
Panasonic Printer CL500 User Manual