21A2695
FIRST
CLASS
STAMP
HERE
MODEL 600WM
WATER RESISTANT
IN CEILING LOUDSPEAKER
4545 E BASELINE RD
PHOENIX AZ 85040-6400
OWNERS MANUAL
OTHER BLUEPRINT SERIES PRODUCTS FROM MTX
MTX offers a wide assortment of audio components. Ranging from in-wall speakers to
amplifiers to accessories. Each component is value engineered and must meet strict
quality control standards before it becomes part of the MTX product line.
THE MODEL 600WM WATER RESISTANT LOUDSPEAKER
The MODEL 600WM is specifically designed for use in areas where moisture is
present, such as bath, sauna, hot tub area, patio, poolside and other exterior appli-
cations. If you are planning an installation of this type, we strongly recommend
the MODEL 600WM Water Resistant Loudspeaker.
Listed below you will find a sampling of MTX components available from your autho-
rized Blueprint Series dealer.
IN-WALL LOUDSPEAKERS
MODEL 520W
LOUDSPEAKER PLACEMENT
MODEL 502W
5-1/4” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/84dB Sensitivity
53Hz-20kHz Frequency Response
50 Watts RMS/160 Watts Total
11”H x 7-1/2”W x 2-1/2”D
5-1/4” Two-Way In-Wall Speaker
1/2” Polycarbonate Dome Tweeter
8 Ohm Impedance/84dB Sensitivity
53Hz-20kHz Frequency Response
45 Watts RMS/140 Watts Total
11”H x 7-1/2”W x 2-1/2”D
MTX In-Walls can be positioned virtually anywhere you desire sound. Important
considerations are room layout, furniture arrangement, location of audio/video
equipment and daily foot traffic within the room/house. MTX In-Walls are
designed to be installed between wall studs, so avoid locations next to doors,
windows or other construction that may present difficulties. If used for video, In-
Walls should be placed at least six feet away from your video screen, to avoid
magnetic interference.
MODEL 620W
6-1/2” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/85dB Sensitivity
43Hz-20kHz Frequency Response
55 Watts RMS/180 Watts Total
12-1/16”H x 8-9/16”W x 2-7/8”D
MODEL 602W
6-1/2” Two-Way In-Wall Speaker
1/2” Polycarbonate Dome Tweeter
8 Ohm Impedance/85dB Sensitivity
43Hz-20kHz Frequency Response
50 Watts RMS/160 Watts Total
12-1/16”H x 8-9/16”W x 2-7/8”D
MODEL 820W
8” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/86dB Sensitivity
33Hz-20kHz Frequency Response
60 Watts RMS/200 Watts Total
14-1/16”H x 10-1/16”W x 3-1/2”D
SPEAKER/AMPLIFIER SELECTOR
LPS-600
Accommodates up to 6 pair of speakers
Handles up to 250 Watts/channel continuous (RMS)
Impedance Protection Circuitry
Low profile-full size component
Two-piece, plug in connectors on the rear panel
Accommodates up to 14 gauge wire
TV-5 UL Approved Switches
Drop ceiling wiring example
Exterior soffit example
Baseboard/carpet wiring
example
A/B Amplifier and Input Selector
ACCESSORIES
VC-30B/VC-30W
Decora-Style Volume Control (Bone or White)
10 Step 25 Watts per channel (RMS) 150 Watts Peak
AB-1SB/AB-1SW
Decora-Style A/B Switch (Bone or White)
PCK65C
Pre-Construction Kit for Model 610RCM
Attic wiring example
Basement wiring example
PCK85C
Pre-Construction Kit for Model 810RCM
STEP 1
STEP 4
Using a stud finder (available at low cost at most hardware stores) or other accu-
rate method, locate center point between two studs and mark. Using template
provided, trace hole pattern on surface of wall. Placing a bubble level on either
the horizontal or vertical guidelines of template will assist you in leveling hole
pattern.
Attach loudspeaker wires to speaker terminals, observing correct polarity, and
position speaker frame assembly to hole as shown. Insert top of mounting frame
into hole at top. By moving bottom of frame upwards, you should now be able
to insert bottom of frame into hole at bottom. Be careful not to pinch wires in the
process. Tighten long screws. Use a level during tightening to insure straightness
of final position.
STEP 2
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in wall, fol-
lowing traced pattern.
STEP 5
After the speaker panel is secured tightly, test for sound. When you are satisfied
the speaker is operational, affix grill. As grill is designed for a snug fit, you’ll
need to position one edge into slot first, and press or squeeze around perimeter
of grill, while pushing leading edges into grill slot.
STEP 3
Run loudspeaker wires to sound source location. There are several methods you
can use to accomplish wiring, depending on the construction characteristics of
the room or house (see Loudspeaker Placement). You can add a professional
touch to your installation by using a speaker terminal plate at the source location.
Leave sufficient amount of wire at speaker location (8 to 10 inches) to complete
connection.
|