21A2692
FIRST
CLASS
STAMP
HERE
MODEL 510CM
WATER RESISTANT
IN CEILING LOUDSPEAKER
4545 E BASELINE RD
PHOENIX AZ 85040-6400
OWNERS MANUAL
OTHER BLUEPRINT SERIES PRODUCTS FROM MTX
MTX offers a wide assortment of audio components. Ranging from in-wall speakers to
amplifiers to accessories. Each component is value engineered and must meet strict
quality control standards before it becomes part of the MTX product line.
LOUDSPEAKER PLACEMENT
Blueprint Series Loudspeakers are designed to work within any interior decorat-
ing scheme. They can be installed in virtually any location where flush mount-
ing is possible. To maximize their sound performance however certain guidelines
should be followed. For the best stereo reproduction the two loudspeakers should
be placed an equal distance from your listening position and separated so that the
angle between them, at the listening position, is between 40 and 60 degrees.
Listed below you will find a sampling of MTX components available from your autho-
rized Blueprint Series dealer.
IN-WALL LOUDSPEAKERS
MODEL 520W
MODEL 502W
5-1/4” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/84dB Sensitivity
53Hz-20kHz Frequency Response
50 Watts RMS/160 Watts Total
11”H x 7-1/2”W x 2-1/2”D
5-1/4” Two-Way In-Wall Speaker
1/2” Polycarbonate Dome Tweeter
8 Ohm Impedance/84dB Sensitivity
53Hz-20kHz Frequency Response
45 Watts RMS/140 Watts Total
11”H x 7-1/2”W x 2-1/2”D
MODEL 620W
MODEL 602W
6-1/2” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/85dB Sensitivity
43Hz-20kHz Frequency Response
55 Watts RMS/180 Watts Total
12-1/16”H x 8-9/16”W x 2-7/8”D
6-1/2” Two-Way In-Wall Speaker
1/2” Polycarbonate Dome Tweeter
8 Ohm Impedance/85dB Sensitivity
43Hz-20kHz Frequency Response
50 Watts RMS/160 Watts Total
12-1/16”H x 8-9/16”W x 2-7/8”D
MODEL 820W
MODEL 600WM
8” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/86dB Sensitivity
33Hz-20kHz Frequency Response
60 Watts RMS/200 Watts Total
14-1/16”H x 10-1/16”W x 3-1/2”D
6-1/2” Water Resistant Co-Axial In-Wall Speaker
1/2” Polycarbonate Dome Tweeter
8 Ohm Impedance/88dB Sensitivity
64Hz-20kHz Frequency Response
35 Watts RMS/140 Watts Total
8-5/8”H x 8-5/8”W x 2-3/4”D
SPEAKER/AMPLIFIER SELECTOR
LPS-600
Accommodates up to 6 pair of speakers
Handles up to 250 Watts/channel continuous (RMS)
Impedance Protection Circuitry
Low profile-full size component
Two-piece, plug in connectors on the rear panel
Accommodates up to 14 gauge wire
TV-5 UL Approved Switches
A/B Amplifier and Input Selector
ACCESSORIES
VC-30B/VC-30W
Decora-Style Volume Control (Bone or White)
10 Step 25 Watts per channel (RMS) 150 Watts Peak
AB-1SB/AB-1SW
Decora-Style A/B Switch (Bone or White)
PCK65C
Pre-Construction Kit for Model 610RCM
PCK85C
Pre-Construction Kit for Model 810RCM
STEP 1
STEP 4
Using a stud finder (available at low cost at most hardware stores) or other accu-
rate method, locate center point between two joists and mark. Using template
provided, trace hole pattern on surface of ceiling.
Attach loudspeaker wires to speaker terminals, observing correct polarity, and
position speaker frame up into cutout. Be careful not to pinch wires in the
process.
STEP 2
STEP 5
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in wall, fol-
lowing traced pattern.
Carefully tighten the four mounting screws. This will cause the mounting wings
to rotate out behind the mounting surface and secure the speaker in place.
STEP 3
STEP 6
Run loudspeaker wires to sound source location. There are several methods you
can use to accomplish wiring, depending on the construction characteristics of
the room or house. You can add a professional touch to your installation by using
a speaker terminal plate at the source location. Leave sufficient amount of wire
at speaker location (8 to 10 inches) to complete connection.
After the speaker panel is secured tightly, test for sound. When you are satisfied
the speaker is operational, affix grill. The Model 510CM grill can be installed
into the speaker frame for either a standard flush mount cosmetic appearance or
a recessed look similar to a coilex type of light fixture. After deciding which look
is preferred press the grill into the frame until the leading edge is flush.
|