Metra Electronics Musical Instrument Amplifier 99 7319 User Manual |
INSTALLATION INSTRUCTIONS FOR PART 99-7319
APPLICATIONS
2004-2006 Kia Amanti
99-7319
KIT FEATURES
• DIN Head Unit Provision
• ISO DIN Head Unit Provision
KIT COMPONENTS
A) Radio Housing B) A/C Control Brackets C) ISO Brackets D) Trim plate
A
B
D
C
TOOLS REQUIRED:
Phillips Screwdriver I Small Flat Blade Screwdriver
1-800-221-0932
© COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION
DASH DISASSEMBLY
99-7319
2004-2006 KIA AMANTI
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
2
Unclip and remove panel surround-
ing shifter including cup holders.
(Figure A)
Remove (2) Phillips screws at base
of panel surrounding radio and a/c
controls. (Figure B)
3
4
Unclip and remove panel surround-
B
ing radio and a/c control. (Figure C)
C
1
DASH DISASSEMBLY
99-7319
2004-2006 KIA AMANTI
D
5
6
Remove (6) Phillips screws securing
radio and a/c control. (Figure D)
Remove (4) Phillips screws securing
factory a/c control to bracket assem-
bly. (Figure E)
VOL
LOAD
E
2 Phillips screws on each side
2
KIT ASSEMBLY
99-7319
2004-2006 KIA AMANTI
DIN HEAD UNIT PROVISION
A
Attach the corresponding a/c control
1
bracket to the factory a/c control
using the factory hardware. (Figure A)
Note: The radio housing must be
installed first before the a/c control.
Slide the DIN cage into the radio
housing and secure by bending the
metal locking tabs down. (Figure B)
1
2
B
Slide the aftermarket head unit into
the cage and secure. (Figure C)
C
3
KIT ASSEMBLY
99-7319
2004-2006 KIA AMANTI
ISO DIN HEAD UNIT PROVISION
A
Attach the corresponding a/c control
bracket to the factory a/c control
1
using the factory hardware. (Figure A)
Note: The radio housing must be
installed first before the a/c control.
Mount the ISO bracket to the head
1
unit with screws supplied with the
unit. (Figure B)
B
Slide the head unit into the radio
opening until the side clips engage.
(Figure C)
2
Snap the trim plate into the radio
3
housing. (Figure C)
C
4
FINAL ASSEMBLY
99-7319
FINAL ASSEMBLY
A
B
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown.
(Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
1
Re-connect the negative battery terminal and test the unit for proper operation.
2
3
Reassemble radio and dash assemblies in reverse order of disassembly
installing the radio housing first and then the a/c control.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
Right Front (+) . . . . . Gray
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-). . . . . . . White / Black
Right Rear (+). . . . . . Violet
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
5
99-7319 INSTRUCTIONS
1-800-221-0932
REV. 06/19/2007
© COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION
INST99-7319
|