Metra Electronics Automobile Accessories 99 7501 User Manual

INST 7501  
KIT COMPONENTS  
MAZDA 323 1986-89  
"A"  
Radio  
Housing  
99-7501  
INSTALLATION  
INSTRUCTIONS  
"A"  
Pocket  
Fig. A  
Fi
Fig. C  
1" Spacer  
½" Spacer  
APPLICATIONS  
ISO-DIN  
Trimring  
CAR  
MAZDA  
PAGE  
Equalizer  
Faceplate  
323 1986-89.......................................................................1  
323 1990-94.......................................................................2  
626 1986-87.......................................................................3  
626 1988-92 ......................................................................4  
929 1988-91.......................................................................5  
B-Series Pickup 1986-93...................................................... 6  
Miata 1990-99.................................................................... 7  
MPV 1989-95.......................................................................8  
MX6 1986-87...................................................................... 3  
MX6 1988-92...................................................................... 4  
Protege 1990-94................................................................. 2  
RX-7 1984-85......................................................................9  
RX-7 1986-91......................................................................10  
Fig. D  
Fig. E  
Fig. F  
Bracket  
Set #1  
1. Disconnect the negative battery terminal to prevent an accidental short circuit. Remove  
the ashtray and (2) screws inside the ashtray cavity. Unsnap the bezel and disconnect  
any wiring. Remove (4) screws securing the dummy plate to the back of the bezel (see  
Fig. A).  
Bracket  
Set #2  
2. Cut and remove all mounting tabs on the Radio Housing except tabs "A" (see Fig. B).  
Spacer  
Set #1  
3. Convert the Radio Housing to SINGLE DIN by cutting along the lower scored lines and  
removing the bottom portion of the Housing (see Fig. C).  
Spacer  
Set #2  
(6) #6 Flat-  
head Screws  
4. Attach the 1" Spacer under the radio opening (see Fig. D).  
5. SHAFT HEAD UNITS: Slide the unit into the kit and secure with shaft nuts.  
DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing, slide  
the DIN cage into the kit and secure.  
Rear  
Suppor
(4) #8 Phillip  
Screws  
ISO-DIN HEAD UNITS: Cut and remove all tabs from Bracket Set #1 OR Bracket Set  
#2 and mount to the Radio Housing with (4) #6 Flat-head screws. Cut and remove  
the shaft supports from the Radio Housing and snap the ISO-DIN Trimring into the  
radio opening. Slide the ISO-DIN Spacers into the rear slots of the Radio Housing and  
insert the unit into the kit. Mount through the aligned holes with (4) 3/8" Machine-  
thread screws.  
(4) 3/8" Machine-  
thread Screws  
(2) PPH  
Screws  
ISO-DIN Spacers  
6. Locate the factory wiring harness in the dash. Metra recommends using the proper  
mating adaptor and making connections as follows: Strip wire ends back ½", Twist  
together, Solder and Tape. Isolate and individually tape off the ends of any unused  
wires to prevent electrical short circuit.  
TOOLS REQUIRED  
7. Secure the Rear Support Bracket to the rear of the unit (see Fig. E).  
Phillips screwdriver  
Cutting tool  
8. Place Spacer Set #1 behind tabs "A" and mount the radio/kit assembly to the sub-dash  
with PPH1 screws and NS10 washers supplied (see Fig. F). Be sure the Rear  
Support Bracket engages.  
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION  
1
rev. 300801  
 
MAZDA 626 / MX6 1988-92  
MAZDA 929 1988-91  
"B"  
"A"  
"A"  
"B"  
Fig.
Fi
Fig. C  
Fi
Fig. C  
Fig. E  
Fig. F  
Fig. D  
Fig. D-2  
Fig. E  
Fig. D-1  
1. Disconnect the negative battery terminal to prevent an accidental short circuit. Reach  
behind the console and remove (2) nuts supporting the radio carrier. Remove the  
factory radio and disconnect the wiring. (see Fig. A)  
1. Disconnect the negative battery terminal to prevent an accidental short circuit. Remove  
the ashtray and (2) Phillips screws exposed in the ashtray cavity. Remove the pocket  
from the trim panel and (2) Phillips screws exposed. Unclip the panel and remove (4)  
screws securing the factory dummy plate. Note: if equipped with a factory pocket 3¾"  
or taller, discard the factory pocket and use the pocket supplied in the kit. (see Fig. A)  
2. Cut and remove all mounting tabs except tabs "A". (see Fig. B)  
3. Mount each converted Bracket to the Radio Housing with (3) #6 Flat-head screws.  
(see Fig. C)  
2. Cut and remove all mounting tabs on Bracket Set #2 except tabs "B". (see Fig. B)  
3. Cut and remove the mounting tabs on the Radio Housing and mount each converted  
Bracket to the converted Housing with (3) #6 Flat-head screws. (see Fig. C)  
4. IF AN EQUALIZER WILL BE INCLUDED: Attach the Equalizer Faceplate to the Radio  
Housing and mount the equalizer with the necessary hardware. (see Fig. D-2)  
IF AN EQUALIZER WILL NOT BE INCLUDED: Snap the supplied Pocket and ½"  
Spacer into the Radio Housing. (see Fig. D-1)  
4. IF AN EQUALIZER WILL NOT BE INCLUDED: Attach the Equalizer Faceplate to the  
Radio Housing and snap the Equalizer Cover into the opening in the Housing.  
IF AN EQUALIZER WILL BE INCLUDED: Attach the Equalizer Faceplate to the  
Radio Housing and mount the equalizer with the necessary hardware. (see Fig. D)  
5. SHAFT HEAD UNITS: Slide the unit into the kit and secure with shaft nuts.  
DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing, slide  
the DIN cage into the kit and secure.  
5. SHAFT HEAD UNITS: Slide the unit into the kit and secure with shaft nuts.  
DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing, slide  
the DIN cage into the kit and secure.  
ISO-DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing  
and snap the ISO-DIN Trimring into the radio opening. Slide the ISO-DIN Spacers into  
the rear slots of the Radio Housing and insert the unit into the kit. Mount through the  
aligned holes with (4) 3/8" Machine-thread screws.  
ISO-DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing  
and snap the ISO-DIN Trimring into the radio opening. Slide the ISO-DIN Spacers into  
the rear slots of the Radio Housing and insert the unit into the kit. Mount through the  
aligned holes with (4) 3/8" Machine-thread screws.  
6. Locate the factory wiring harness in the dash. Metra recommends using the proper  
mating adaptor and making connections as follows: Strip wire ends back ½", Twist  
together, Solder and Tape. Isolate and individually tape off the ends of any unused  
wires to prevent electrical short circuit.  
6. Locate the factory wiring harness in the dash. Metra recommends using the proper  
mating adaptor and making connections as follows: Strip wire ends back ½", Twist  
together, Solder and Tape. Isolate and individually tape off the ends of any unused  
wires to prevent electrical short circuit.  
7. Mount the radio/kit assembly to the sub-dash with (4) screws previously removed. (see  
Fig. E)  
7. Snap the Pocket into the bottom of the radio trim panel. (see Fig. E) Mount the radio/kit  
assembly to the sub-dash with (4) screws previously removed. (see Fig. F)  
4
5
 
MAZDA B-Series Pickup 1986-93  
MAZDA Miata 1990-99  
"C"  
"B"  
"E"  
"B"  
Fig. A  
F
Fig. C  
Fig
Fig. C  
Fig. D-2  
Fig. E  
Fig. D-2  
Fig. E  
Fig. D-1  
Fig. D-1  
1. Disconnect the negative battery terminal to prevent an accidental short circuit. Remove  
(2) screws from each side of the console trim panel. Remove the ashtray and (1) screw  
from the rear support tab. Remove the console sub-bracket assembly. Remove (4)  
screws securing the console/radio sub-bracket to the back of the console panel, and  
loosen (2) screws on top of the panel. Remove the console/radio sub-bracket from the  
bezel. (see Fig. A)  
1. Disconnect the negative battery terminal to prevent an accidental short circuit. Remove  
(2) screws from the console box and (1) screw under the ashtray. Remove (1) screw  
exposed at the base of the radio trim panel. Pop out the a/c vents and remove (2)  
screws inside. Remove the trim panel. (see Fig. A)  
2. Cut and remove all mounting tabs on Bracket Set #1 except tabs "B". (see Fig. B)  
2. Cut and remove all mounting tabs on Bracket Set #2 except tabs "C" & "E". (see Fig.  
B)  
3. Cut and remove the mounting tabs on the Radio Housing and mount each converted  
Bracket to the converted Housing with (3) #6 Flat-head screws. (see Fig. C)  
3. Cut and remove the mounting tabs on the Radio Housing and mount each converted  
Bracket to the converted Housing with (3) #6 Flat-head screws. (see Fig. C)  
4. IF AN EQUALIZER WILL BE INCLUDED: Attach the Equalizer Faceplate to the  
Radio Housing and mount the equalizer with the necessary hardware. (see Fig. D-1)  
IF AN EQUALIZER WILL NOT BE INCLUDED: Snap the supplied Pocket and ½"  
Spacer into the Radio Housing. (see Fig. D-2)  
4. IF AN EQUALIZER WILL BE INCLUDED: Attach the Equalizer Faceplate to the  
Radio Housing and mount the equalizer with the necessary hardware. (see Fig. D-1)  
IF AN EQUALIZER WILL NOT BE INCLUDED: Snap the supplied Pocket and ½"  
Spacer into the Radio Housing. (see Fig. D-2)  
5. SHAFT HEAD UNITS: Slide the unit into the kit and secure with shaft nuts.  
DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing, slide  
the DIN cage into the kit and secure.  
5. SHAFT HEAD UNITS: Slide the unit into the kit and secure with shaft nuts.  
DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing, slide  
the DIN cage into the kit and secure.  
ISO-DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing  
and snap the ISO-DIN Trimring into the radio opening. Slide the ISO-DIN Spacers into  
the rear slots of the Radio Housing and insert the unit into the kit. Mount through the  
aligned holes with (4) 3/8" Machine-thread screws.  
ISO-DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing  
and snap the ISO-DIN Trimring into the radio opening. Slide the ISO-DIN Spacers into  
the rear slots of the Radio Housing and insert the unit into the kit. Mount through the  
aligned holes with (4) 3/8" Machine-thread screws.  
6. Locate the factory wiring harness in the dash. Metra recommends using the proper  
mating adaptor and making connections as follows: Strip wire ends back ½", Twist  
together, Solder and Tape. Isolate and individually tape off the ends of any unused  
wires to prevent electrical short circuit.  
6. Locate the factory wiring harness in the dash. Metra recommends using the proper  
mating adaptor and making connections as follows: Strip wire ends back ½", Twist  
together, Solder and Tape. Isolate and individually tape off the ends of any unused  
wires to prevent electrical short circuit.  
7. Mount the radio/kit assembly to the sub-dash with (4) screws previously removed. (see  
Fig. E)  
7. Mount the radio/kit assembly to the sub-dash with (4) screws previously removed.  
(see Fig. E)  
6
7
 
MAZDA RX-7 1984-85  
MAZDA MPV 1989-95  
"D"  
"D"  
Fig. B  
Fig. C  
F
Fig. C  
"B"  
F
Fig. F  
Fig. D  
Fig. D-2  
Fig. E  
Fig. D-1  
1. Disconnect the negative battery terminal to prevent an accidental short circuit. Remove  
the ashtray and (2) screws within the ashtray cavity. Carefully pull the trim panel away  
from the dash and disconnect any wiring. Remove (4) screws securing the factory radio  
to the sub-dash and disconnect the wiring. (see Fig. A)  
1. Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap  
the gear shifter plate and remove (2) screws exposed at the base of the radio trim  
panel. Remove the a/c knobs and nuts. Gently pull out on the top edge of the radio trim  
panel and remove the panel. (see Fig. A)  
2. Convert the Radio Housing to SINGLE DIN by cutting along the lower scored lines and  
removing the bottom portion of the Housing. (see Fig. B)  
2. Cut and remove all mounting tabs on Bracket Set #2 except tabs "D". (see Fig. B)  
3. Cut and remove all mounting tabs on the Radio Housing except tabs "D" and mount  
each converted Bracket to the converted Housing with (3) #6 Flat-head screws. (see  
Fig. C)  
3. Attach the 1" Spacer under the radio opening. (see Fig. C)  
4. Cut and remove all mounting tabs on the Radio Housing except tabs "B". (see Fig. D)  
4. IF AN EQUALIZER WILL BE INCLUDED: Attach the Equalizer Faceplate to the  
Radio Housing and mount the equalizer with the necessary hardware. (see Fig. D-1)  
IF AN EQUALIZER WILL NOT BE INCLUDED: Snap the supplied Pocket and ½"  
Spacer into the Radio Housing. (see Fig. D-2)  
5. SHAFT HEAD UNITS: Slide the unit into the kit and secure with shaft nuts.  
DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing, slide  
the DIN cage into the kit and secure.  
ISO-DIN HEAD UNITS: Cut and remove the tabs from Bracket Set #1 OR Bracket Set  
#2 and mount to the Radio Housing with (4) #6 Flat-head screws. Cut and remove  
the shaft supports from the Radio Housing and snap the ISO-DIN Trimring into the  
radio opening. Slide the ISO-DIN Spacers into the rear slots of the Radio Housing and  
insert the unit into the kit. Mount through the aligned holes with (4) 3/8" Machine-  
thread screws.  
5. 2-SHAFT HEAD UNITS: Slide the unit into the kit and secure with shaft nuts.  
DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing, slide  
the DIN cage into the kit and secure.  
ISO-DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing  
and snap the ISO-DIN Trimring into the radio opening. Slide the ISO-DIN Spacers into  
the rear slots of the Radio Housing and insert the unit into the kit. Mount through the  
aligned holes with (4) 3/8" Machine-thread screws.  
6. Locate the factory wiring harness in the dash. Metra recommends using the proper  
mating adaptor and making connections as follows: Strip wire ends back ½", Twist  
together, Solder and Tape. Isolate and individually tape off the ends of any unused  
wires to prevent electrical short circuit.  
6. Locate the factory wiring harness in the dash. Metra recommends using the proper  
mating adaptor and making connections as follows: Strip wire ends back ½", Twist  
together, Solder and Tape. Isolate and individually tape off the ends of any unused  
wires to prevent electrical short circuit.  
7. Secure the Rear Support Bracket to the rear of the unit and insert the bottom flap into  
the dash provisiosn. (see Fig. E)  
7. Mount the radio/kit assembly to the sub-dash with (4) screws previously removed. (see  
Fig. E)  
8. Mount the radio/kit assembly to the sub-dash with (2) screws previously removed. (see  
Fig. F)  
8
9
 
MAZDA RX-7 1986-91  
"A"  
"A"  
"C"  
"C"  
Fig. A  
Fig. B  
Fig. C  
Fig. D-2  
Fig. E  
Fig. D-1  
1. Disconnect the negative battery terminal to prevent an accidental short circuit. Remove  
the ashtray and (2) screws within the ashtray cavity. Unsnap the shifter boot molding  
and remove the (2) screws exposed. Unsnap the a/c control bezel and remove the (2)  
screws exposed. Pull the bezel away from the dash and disconnect any wiring.  
Remove (4) screws from the factory radio and disconnect the wiring. (see Fig. A)  
2. Mount Spacer Set #2 to the back of the radio trim panel with (4) #8 Phillips screws.  
(see Fig. B)  
3. Cut and remove all mounting tabs on the Radio Housing except tabs "A" & "C". (see  
Fig. C)  
4. IF AN EQUALIZER WILL BE INCLUDED: Attach the Equalizer Faceplate to the  
Radio Housing and mount the equalizer with the necessary hardware. (see Fig. D-1)  
IF AN EQUALIZER WILL NOT BE INCLUDED: snap the supplied Pocket and ½"  
Spacer into the Radio Housing. (see Fig. D-2)  
5. 2-SHAFT HEAD UNITS: Slide the unit into the kit and secure with shaft nuts.  
DIN HEAD UNITS: Cut and remove the shaft supports from the Radio Housing, slide  
the DIN cage into the kit and secure.  
ISO-DIN HEAD UNITS: Cut and remove the mounting tabs from Bracket Set #1 OR  
Bracket Set #2 and mount to the Radio Housing with (6) #6 Flat-head screws. Cut  
and remove the shaft supports from the Radio Housing and snap the ISO-DIN Trimring  
into the radio opening. Slide the ISO-DIN Spacers into the rear slots of the Radio  
Housing and insert the unit into the kit. Mount through the aligned holes with (4) 3/8"  
Machine-thread screws.  
6. Locate the factory wiring harness in the dash. Metra recommends using the proper  
mating adaptor and making connections as follows: Strip wire ends back ½", Twist  
together, Solder and Tape. Isolate and individually tape off the ends of any unused  
wires to prevent electrical short circuit.  
7. Mount the assembly to the sub-dash with (4) screws previously removed. (see Fig. E)  
10  
 

Lennox Hearth Indoor Fireplace SOLANA BK User Manual
Lennox International Inc Furnace G24M SERIES User Manual
LifeCore Fitness Home Gym LC 990 User Manual
Lincoln Electric Welder SVM135 B User Manual
Macsense Connectivity Switch XRouter Pro User Manual
Makita Grinder 9556PB User Manual
Maytag Washer MGWE550WJ User Manual
Maytag Water Heater HN41240X User Manual
Meade Telescope 10 125 Starfinder User Manual
Metra Electronics Automobile Accessories 99 7506 User Manual