Memorex Universal Remote URC 4880 User Manual

URC 4880 VIDEO EXPERT PLUS  
WITH LEARNING  
Universal Remote Control  
4-DEVICE  
Users Guide  
 
Key Charts  
FEATURES AND FUNCTIONS  
Use SET for all programming  
sequences.  
Use the illustration below to locate One ForAll 4-DeviceVideo  
Expert Plus With Learning remote control features and then  
study the Key Charts (on the next two pages) to learn how they  
function.  
The LED (red light) blinks to show that  
the remote control is working and is  
sending signals.  
Use M.POWER to set up and turn on (or  
off) all TV,VCR,and DVD components  
with a single key.Also see page 25.  
Press POWER once to turn on (or off)  
a selected home entertainment  
component.  
Press TV,DVD,VCR,or CBL/SAT once  
to select a home entertainment video  
component to control.  
Use the learning keys,L1, L2, L3, or L4,  
to store and recall additional remote  
control functions.Also see page 30.  
Use EXIT to exit out of your cable  
converters menu and guide.  
Press MENU once to display the selected  
components screen menu. Use the VOL  
+/- and CH +/- keys to navigate menus  
and press the MUTE key to select items.  
Press TV/VID to switch viewing between  
TV and video sources.  
Use VOL + (or VOL -) to raise (or lower)  
the sound volume.  
Use CH + (or CH -) to select the next  
higher (or lower) channel.  
Press MUTE/SELECT once to turn sound  
off or on.Also,use MUTE/SELECT to  
select items from the selected  
components screen menu after  
pressing MENU once.  
After pressing MENU,use the Cursor  
Keys to move the cursor in the program  
guide and menu screens.  
continued on next page...  
4
5
 
FEATURES AND FUNCTIONS  
INSTALLING BATTERIES  
Key Charts (Continued)  
Press PIP once to view or turn off the  
picture-in-picture feature.  
Press SWAP once to exchange the PIP  
with the main TV picture.  
Use MOVE to the picture-in-picture  
position on the TV screen.  
Press SLEEP once to enable (or disable)  
a selected components sleep timer  
(if available).  
Use DISPLAY to view a selected  
components information on the TV.  
Use the keypad (0 ~ 9) to directly select  
channels (e.g.,09 or 31).  
Press ENTER once after entering  
channel numbers on some TV  
models.  
Press PREV.CH once to recall the  
last-viewed channel.  
Use V.CONFIG to custom program and  
recall video configuration modes for  
home theater use.Also see page 32.  
1.  
2.  
On the back of the remote control, press the  
recess and slide the battery cover off (see above).  
In the TV,DVD,or VCR mode,use the  
FWD SCAN,REW SCAN,PLAY,STOP,and  
PAUSE keys to control your VCR or DVD  
(or LD) player.To record a program on,  
theVCR,press REC twice.  
Obtain two (2) fully-charged AA alkaline  
batteries.Match the + and – marks on the  
batteries to the + and – marks in the battery  
case,then insert the new batteries.  
3.  
4.  
Align the cover keys with the case openings  
and slide the cover on until it locks.  
Test the unit by pressing POWER and any mode  
key (e.g.TV,DVD,VCR,or CBL/SAT).If batteries  
are inserted correctly,the LED will blink once.  
NOTE:When batteries need replacement, the One For All  
4-Device Video Expert Plus remote control will cease to operate.  
Simply replace the batteries and the unit will be restored to its full  
functionality, complete with your favorite settings.  
6
7
 
PROGRAMMING TV CONTROL  
Ampro  
0751  
Anam  
0180  
NOTE: If you own a TV/VCR combination, skip this section and  
performProgramming TV/VCR Combo Control”on page 16.  
Audiovox  
Baysonic  
Belcor  
Bell & Howell  
Bradford  
Brockwood  
Broksonic  
CXC  
Candle  
Carnivale  
Carver  
Celebrity  
Cineral  
Citizen  
0451,0180,0092,0623  
0180  
0019  
0154  
0180  
0019  
0236,0463  
0180  
0030,0056  
0030  
0054  
0000  
0451,0092  
0060,0030,0056,0039,0092  
Locate the brand name of your TV in the Setup Codes For  
TVs section below, and write it in the following space.  
TV Brand: __________________________________  
The brands are listed in alphabetical order with the most  
popular codes listed first.To program TV control:  
1.  
2.  
Turn on the TV.  
On the remote control,press TV once. Press and  
hold SET until the LED blinks twice,then  
release SET.  
Concerto  
Contec  
Craig  
0056  
0180  
0180  
NOTE: The remote control will exit programming if  
more than 10 seconds elapse between key presses.  
3.  
Enter the first four-digit code for your TV. If  
you perform this procedure correctly,the LED  
will blink twice.  
Crosley  
Crown  
Curtis Mathes  
0054  
0180,0039  
0047,0054,0154,0051,0451,0093,0060,0030,0145,0056,  
0039,0166,0466,1147,1347  
NOTE: If the LED emits a long blink, the code is  
invalid. Repeat steps 2 through 3 and try entering the  
same code again.  
Daewoo  
Daytron  
Denon  
0451,0019,0039,0092,0623,0624  
0019  
0145  
Dumont  
Dwin  
Electroband  
Emerson  
0017,0019  
0720,0774  
0000  
4.  
5.  
Aim the remote control at your TV and press  
POWER once.The TV should turn off.If it does  
not respond,repeat steps 2-3,trying each code  
for your brand until you find one that works.If  
it still does not work,try searching for the code  
(see Searching For Your Code on page 23).  
0154,0236,0463,0180,0178,0019,0179,0039,0177,0623,  
0624  
0030  
0154  
0179,0683  
0180,0179,0171  
0180  
0047,0051,0451,0093,0178,0135,1147,1347  
Envision  
Fisher  
Fujitsu  
Funai  
Futuretech  
GE  
Write your TV code in the boxes below for  
future reference.  
Gibralter  
GoldStar  
Gradiente  
Grunpy  
Hallmark  
Harley Davidson  
Harman/Kardon  
Harvard  
Hitachi  
Infinity  
Inteq  
0017,0030,0019  
0030,0178,0019,0056  
0053,0056  
0180,0179  
0178  
0179  
0054  
0180  
0145,0056,0151  
0054  
0017  
0054  
0000  
0053  
NOTE: Remember, to use the One For All 4-Device Video Expert  
Plus With Learning remote control to operate your TV, press TV  
first.  
Setup Codes for TVs:  
AOC  
Admiral  
Aiko  
0030,0019,0052  
0093,0463  
0092  
Akai  
0030  
JBL  
JCB  
JVC  
Alaron  
0179  
Ambassador  
America Action  
0177  
0180  
continued on next page...  
8
9
 
Sansei  
Sansui  
0451  
0463  
PROGRAMMING TV CONTROL  
Sanyo  
Scimitsu  
Scotch  
0154  
0019  
0178  
Setup Codes for TVs (Continued):  
KEC  
0180  
KTV  
0180,0030,0039  
0052  
0030,0019  
Scott  
Sears  
Semivox  
Semp  
0236,0180,0178,0019,0179  
0047,0054,0154,0156,0178,0179,0056,0171  
0180  
0156  
Kaypani  
Kenwood  
LG  
0056  
LXI  
Luxman  
MGA  
0047,0054,0154,0156,0178  
0056  
0150,0030,0178,0019  
0060,0030,0019,0056  
0054,0030,0179,1254  
0054,0030  
0250  
0178,0145  
0154,0250,0463,0150,0178,0056  
0047,0017,0051,0039,0135  
0093,0150,0178,0019  
0093  
Sharp  
Shogun  
Sony  
Soundesign  
Squareview  
Starlite  
Supreme  
Sylvania  
Symphonic  
TMK  
0093,0165,0039  
0019  
0000  
0180,0178,0179  
0171  
0180  
0000  
0054,0030  
0171  
0178,0056,0177  
0093  
0051,0250  
0179  
0051,0056  
0054,0180,0150,0060,0019,0179,0056,0039,0092  
0056  
0031  
0154,0156,0060,1256  
0039  
0030  
0053  
0054  
0178,0019  
0054,0165,0030,0178,0019,0179,0056  
MTC  
Magnavox  
Marantz  
Matsushita  
Megatron  
Memorex  
Midland  
Mitsubishi  
Motorola  
Multitech  
NAD  
NEC  
NTC  
Nikko  
Onwa  
Optimus  
Optonica  
Orion  
Panasonic  
Penney  
Tandy  
Technics  
Technol Ace  
Techwood  
Teknika  
Telefunken  
Tera  
Toshiba  
Totevision  
Vector Research  
Victor  
0180  
0156,0178,0166  
0030,0019,0056  
0092  
0030,0178,0092  
0180  
0154,0250,0166  
0093,0165  
0236,0463,0179  
0051,0250  
0047,0156,0051,0060,0030,0178,0019,0056,0039,0135,  
1347  
0054,0463,0030,0145,0019  
0054  
0030,0019,0039  
0166  
0019,0039,0092  
0051  
Vidikron  
Vidtech  
Wards  
Philco  
Philips  
Pilot  
White Westinghouse 0463,0623,0624  
Yamaha  
Zenith  
0030,0019  
0017,0463,0092,0624  
Pioneer  
Portland  
Prism  
Proscan  
Proton  
Pulsar  
Quasar  
RCA  
0047  
0178,0031,0052,0466  
0017,0019  
0051,0250,0165  
0047,0051,0093,0019,0090,0135,1047,1147,1247,1347,  
1447  
Radio Shack  
Realistic  
Runco  
0047,0154,0165,0180,0030,0178,0019,0056,0039  
0154,0165,0180,0030,0178,0019,0056,0039  
0017,0030  
SSS  
0180,0019  
Sampo  
Samsung  
Samsux  
0030,0039,0052  
0060,0030,0178,0019,0056  
0039  
10  
11  
 
PROGRAMMING VCR CONTROL  
NOTE: If you own a TV/VCR combination, skip this section and  
performProgramming TV/VCR Combo Control”on page 16.  
America Action  
American High  
Asha  
0278  
0035  
0240  
Audiovox  
Beaumark  
Bell & Howell  
Broksonic  
CCE  
0037  
0240  
0104  
Locate the brand name of yourVCR in the Setup Codes For  
VCRs section below,and write it in the following space.  
0184,0121,0209,0002,0479  
0072,0278  
VCR Brand: __________________________________  
The brands are listed in alphabetical order with the most  
popular codes listed first.You will use one of these codes  
to program the One For All 4-DeviceVideo Expert Plus  
With Learning remote control to operate yourVCR:  
Calix  
Canon  
Carver  
Cineral  
0037  
0035  
0081  
0278  
Citizen  
0037,0278  
1.  
2.  
Turn on yourVCR and insert a video cassette.  
Colt  
Craig  
0072  
0037,0047,0240,0072,0271  
0060,0035,0041,0162  
0240  
0045,0278  
0042  
0000  
0037  
0037  
On the remote control,press VCR once. Press  
and hold SET until the LED blinks twice,then  
release SET.  
Curtis Mathes  
Cybernex  
Daewoo  
Denon  
Dynatech  
Electrohome  
Electrophonic  
Emerex  
Emerson  
Fisher  
3.  
Enter the first four-digit code for yourVCR.If  
you perform this procedure correctly,the LED  
will blink twice.  
0032  
NOTE: If the LED did not blink twice after entering  
the codes last digit, then repeat steps 2 through 3 and  
try entering the same code again.  
0037,0184,0000,0121,0043,0209,0002,0278,0479  
0047,0104  
0035,0033  
0000  
0060,0035,0048,0202,0240  
0000  
0526  
0037,0038  
0000  
0047  
0000  
0081,0038  
0072  
0000,0042,0041  
0042  
Fuji  
Funai  
GE  
4.  
Aim the remote control at yourVCR and press  
POWER once.TheVCR should turn off.If your  
VCR remote control does not have a POWER  
key, press PLAY. If theVCR does not respond,  
repeat steps 2-3,trying each code listed for your  
brand until you find one that works.If theVCR  
still does not work ,try searching for the code  
(see Searching For Your Code on page 23).  
Garrard  
GoVideo  
GoldStar  
Gradiente  
HI-Q  
Harley Davidson  
Harman/Kardon  
Harwood  
Hitachi  
5.  
Write yourVCR code in the boxes below for  
future reference.  
Hughes Network  
JVC  
Jensen  
0067,0041  
0041  
KEC  
KLH  
Kenwood  
Kodak  
LXI  
0037,0278  
0072  
0067,0041,0038  
0035,0037  
0037  
NOTE: Remember, to use the One For All 4-Device Video Expert  
Plus With Learning remote control to operate your VCR, press VCR  
first.  
Setup Codes for VCRs:  
Lloyd's  
0000  
Admiral  
Adventura  
Aiko  
0048,0209  
0000  
0278  
Logik  
MEI  
MGA  
0072  
0035  
0240,0043  
Aiwa  
Akai  
0037,0000  
0041  
MGN Technology 0240  
MTC 0240,0000  
12  
13  
 
continued on next page...  
Singer  
Sony  
0072  
PROGRAMMING VCR CONTROL  
0035,0032,0000,0033  
Sylvania  
Symphonic  
TMK  
Tatung  
Teac  
0035,0081,0000,0043  
0000  
0240  
0041  
Setup Codes for VCRs (Continued):  
Magnasonic  
Magnavox  
Magnin  
0278  
0035,0039,0081,0000,0149  
0240  
0000,0041  
Marantz  
Marta  
Matsushita  
Memorex  
0035,0081  
0037  
0035,0162,0454  
0035,0037,0048,0039,0047,0240,0000,0104,0209,0454,  
1037,1162,1262  
0042  
0048,0067,0043  
0035,0048  
0000,0072  
0104,0067,0041,0038  
Technics  
Teknika  
Thomas  
Tivo  
Toshiba  
Totevision  
Unitech  
Vector  
Vector Research  
Video Concepts  
Videosonic  
Wards  
0035,0162,0202  
0035,0037,0000  
0000  
0618  
0045,0043  
0037,0240  
0240  
0045  
Minolta  
Mitsubishi  
Motorola  
Multitech  
NEC  
0038  
0045  
0240  
Nikko  
0037  
0240  
0035  
Noblex  
Olympus  
Optimus  
Orion  
Panasonic  
Penney  
Pentax  
Philco  
0060,0035,0048,0047,0081,0240,0000,0042,0072,0149  
White Westinghouse 0209,0278  
0037,0048,0104,0162,0454,1048,1062,1162,1262  
0184,0209,0002,0479  
0035,0162,0225,0454,0616,1062,1162,1262  
0035,0037,0240,0042,0038  
0042  
0035,0209,0479  
XR-1000  
Yamaha  
Zenith  
0035,0000,0072  
0038  
0039,0000,0209,0033,0479  
Philips  
Pilot  
0035,0081,0618  
0037  
Pioneer  
Profitronic  
Proscan  
Protec  
0067  
0240  
0060,0202  
0072  
Pulsar  
0039  
Quasar  
RCA  
0035,0162,0454,1162  
0060,0035,0048,0240,0042,0149,0202  
Radio Shack  
Radix  
0000,1037  
0037  
Randex  
Realistic  
ReplayTV  
Runco  
0037  
0035,0037,0048,0047,0000,0104  
0614,0616  
0039  
STS  
0042  
Samsung  
Sanky  
0240,0045  
0048,0039  
Sansui  
0000,0067,0209,0041,0271,0479  
Sanyo  
0047,0240,0104  
Scott  
0184,0045,0121,0043  
Sears  
0035,0037,0047,0000,0042,0104  
Semp  
Sharp  
Shintom  
Shogun  
0045  
0048  
0072  
0240  
14  
15  
 
6.  
Write your TV/VCR Combo code in the boxes  
below for future reference.  
PROGRAMMING TV/VCR COMBO CONTROL  
Locate the brand name of your TV/VCR Combo in the  
Setup Codes For TV/VCR Combos section on the next page,  
and write it in the following space.  
NOTE: Remember, to use the One For All 4-Device Video Expert  
Plus With Learning to operate your TV/VCR Combo, press VCR  
first.  
TV/VCR Combo Brand: ________________________  
The brands are listed in alphabetical order with popular  
codes listed first.You will use one of these codes to pro-  
gram the One For All 4-DeviceVideo Expert Plus With  
Learning remote control to operate your TV/VCR Combo:  
Setup Codes for TV/VCR Combos:  
Brocksonic  
Citizen  
Colt  
0002,0479 (TV:0463)  
0278  
0072  
1.  
Turn on your TV/VCR Combo and insert a  
video cassette.  
2.  
On the remote control,press VCR once. Press  
and hold SET until the LED blinks twice,then  
release SET.  
Curtis Mathes  
Daewoo  
Emerson  
Funai  
0035 (TV:0051)  
0278 (TV:0624)  
0002,0479 (TV:0463),0278 (TV:0624)  
0000  
GE  
0060 (TV:0047),0048 (TV:0093),0035 (TV:0051),0240  
0037 (TV:0056)  
0000  
0000  
0000  
0278  
0000,0081 (TV:0054)  
0240  
1162,1262,0162 (TV:0250),0037 (TV:0056),1037  
0240  
0048 (TV:0093)  
1162,1262,0162 (TV:0250)  
0002,0479 (TV:0463)  
1162,1262,0162 (TV:0250),0035 (TV:0051)  
3.  
4.  
Enter the first four-digit code for your TV/VCR  
Combo.If you perform this procedure correctly,  
the LED will blink twice.  
GoldStar  
Harley Davidson  
Hitachi  
NOTE: If the LED did not blink twice after entering  
the codes last digit, then repeat steps 2 through 3 and  
try entering the same code again.  
Lloyd's  
Magnasonic  
Magnavox  
Magnin  
Memorex  
MGA  
Mitsubishi  
Optimus  
Orion  
Aim the remote control at your TV/VCR Combo  
and press POWER once.The unit should turn  
off.If it does not respond,repeat steps 2-3,try-  
ing each code listed for your brand until you  
find one that works.If it still does not work,try  
searching for the code (see Searching For Your  
Code on page 23).  
Panasonic  
Penney  
0037 (TV:0056),0035 (TV:0051),0240  
Quasar  
Radio Shack  
RCA  
Sansui  
Sanyo  
Sears  
Sharp  
Sony  
Sylvania  
Symphonic  
Thomas  
White Westinghouse 0278 (TV:0624)  
Zenith 0000,0479 (TV:0463)  
0162 (TV:0250) ,0035 (TV:0051)  
1037  
0060 (TV:0047),0048 (TV:0093),0035 (TV:0051),0240  
0000,0479 (TV:0463)  
0240  
0000,0037 (TV:0056)  
0048 (TV:0093)  
0032 (TV:0000)  
0081 (TV:0054)  
0000  
5.  
If you’ve located a TV/VCR setup code that  
works your TV/VCR Combo and a separate TV  
code is also listed,you’ll need to program this  
code into the remote control to access volume  
control (see Programming TV Control on page 8).  
If there is no separate TV code listed,you will  
need to perform the following steps to access  
volume control:  
0000  
a. Press and hold SET until the LED blinks  
twice, then release SET.  
b. Enter 9 - 9 - 3.The LED will blink twice.  
c. Press VCR once.The LED will blink twice.  
16  
17  
 
PROGRAMMING CABLE CONVERTER OR  
SATELLITE RECEIVER CONTROL  
Locate the brand name of your Cable Converter or Satellite  
Receiver in the Setup Codes For Cable Converters or Setup  
Codes For Satellite Receivers section starting below,and  
write it in the appropriate space.  
Archer  
Belcor  
0153,0022,0797  
0056  
0014  
0899  
0056  
0022  
0022  
0153  
0153,0315  
0025  
0040  
0019  
0637  
0002  
0797  
0015,0040  
Bell & Howell  
Bell South  
Cable Star  
Cabletenna  
Cableview  
Century  
Citizen  
ColourVoice  
Comtronics  
Contec  
Digi  
Eastern  
Emerson  
Everquest  
Focus  
Cable Converter Brand: ________________________  
or  
Satellite Receiver Brand:________________________  
The brands are listed in alphabetical order with the most popu-  
lar codes listed first.You will use one of these codes to program  
the One ForAll 4-DeviceVideo Expert Plus With Learning  
remote control to operate your Cable Converter or Satellite  
Receiver.  
0400  
GC Electronics  
Garrard  
Gemini  
General Instrument  
GoldStar  
Goodmind  
Hamlin  
0056  
0153  
1.  
2.  
Turn on the Cable Converter or Satellite Receiver.  
On the remote control,press CBL/SAT once.  
Press and hold SET until the LED blinks twice,  
then release SET.  
0015,0797  
0476,0276,0011,0810  
0144,0040  
0797  
0020,0259,0009,0034  
0011  
0007  
3.  
Enter the first four-digit code for your Cable  
Converter or Satellite Receiver.If performed  
correctly,the LED will blink twice.  
Hitachi  
Hytex  
Jasco  
Jerrold  
Linsay  
0015,0153,0315  
0003,0012,0476,0276,0014,0015,0011,0810  
0440  
0000  
0063  
0063  
0618  
0019,0007  
0021  
NOTE: If the LED did not blink twice after entering  
the codes last digit, then repeat steps 2 through 3 and  
try entering the same code again.  
Memorex  
Movie Time  
NSC  
Novaplex  
Oak  
Optimus  
Panasonic  
Panther  
4.  
5.  
Aim the remote control at your Cable Converter or  
Satellite Receiver and press POWER once.The unit  
should turn off.If it does not respond,repeat steps  
2-3,trying each code listed for your brand until  
you find one that works.If it still does not work ,  
try searching for the code (see page 23).  
0000,0107,0021  
0637  
Write your Cable Converter or Satellite Receiver  
code in the boxes below for future reference.  
Paragon  
Philips  
Pioneer  
0000  
0153,0025  
0144,0533,0877  
Popular Mechanics 0400  
Pulsar  
0000  
Quasar  
RCA  
0000  
0021  
NOTE: Remember, to use the One For All 4-Device Video Expert  
Plus With Learning remote control to operate your Cable  
Converter or Satellite Receiver, press CBL/SAT first.  
Radio Shack  
Recoton  
Regal  
Regency  
Rembrandt  
Runco  
0015,0315,0797,0883  
0400  
0020,0259  
0002  
0011  
Setup Codes for Cable Converters:  
ABC  
0003,0008,0014,0017,0007,0011,0013  
Allegro  
Americast  
Antronix  
0153,0315  
0899  
0022  
0000  
0040  
SL Marx  
18  
19  
 
continued on next page...  
PROGRAMMING CABLE CONVERTER OR  
SATELLITE RECEIVER CONTROL  
PROGRAMMING DVD PLAYER CONTROL  
Locate the brand name of your DVD (or LD) player in the  
Setup Codes For DVDs (or LDs) section on the next page,  
and write it in the following space.  
Setup Codes for Cable Converters (Continued):  
DVD (or LD) Brand: __________________________  
Samsung  
Scientific Atlanta  
Signal  
Signature  
Sprucer  
Starcom  
Stargate  
Starquest  
TV86  
0144,0040  
0008,0477,0017,0877  
0015,0040  
0011  
The brands are listed in alphabetical order with the most  
popular codes listed first.You will use one of these codes to  
program the One ForAll 4-DeviceVideo Expert Plus With  
Learning remote control to operate your DVD (or LD) player:  
0021  
0003,0015  
0015,0040,0797  
0015  
1.  
2.  
Turn on your DVD (or LD) player.  
On the remote control,press DVD once.  
Press and hold SET until the LED blinks twice,  
then release SET.  
0063  
Tandy  
0258  
Teleview  
Timeless  
Tocom  
Toshiba  
Tusa  
0040  
0418  
0012,0013  
0000  
0015  
3.  
4.  
Enter the first four-digit code for your DVD (or  
LD) player.If you perform this procedure cor-  
rectly,the LED will blink twice.  
Unika  
0153,0022  
0007  
0153,0022,0056,0191  
0063,0258  
0000,0525,0899  
0400  
NOTE: If the LED did not blink twice after entering  
the codes last digit, then repeat steps 2 through 3 and  
try entering the same code again.  
United Artists  
Universal  
Viewstar  
Zenith  
Aim the remote control at your DVD (or LD)  
player and press POWER once.The unit should  
turn off.If your DVD (or LD) player remote  
control does not have a POWER key,press  
PLAY.If the DVD (or LD) player does not  
respond,repeat steps 2-3,trying each code list-  
ed for your brand until you find one that works.  
If the DVD (or LD) player still does not work ,  
try searching for the code (see Searching For  
Your Code on page 23).  
Zentek  
Setup Codes for Satellite Receivers:  
AlphaStar  
Echostar  
Expressvu  
0772  
0775,1005  
0775  
General Instrument 0627,0361,0869  
HTS  
0775  
Hitachi  
0819  
5.  
Write your DVD (or LD) player code in the  
boxes below for future reference.  
Hughes Network  
JVC  
0749  
0775  
Jerrold  
0627,0361  
0724,0722  
0724  
0869  
0701  
0724,0722  
0627,0361  
0566,0143,0392,0855  
0869  
Magnavox  
Memorex  
Next Level  
Panasonic  
Philips  
Primestar  
RCA  
Radio Shack  
Sony  
NOTE: Remember,to use the One For All 4-DeviceVideo Expert Plus  
With Learning remote control to operate your DVD (or LD) player,  
press DVD first.  
0639  
Star Choice  
Toshiba  
Uniden  
0869  
0790  
0724,0722  
0856  
Zenith  
20  
21  
 
PROGRAMMING DVD PLAYER CONTROL  
(Continued)  
SEARCHING FOR YOUR CODE  
If your video component does not respond to the One For  
All 4-DeviceVideo Expert Plus With Learning remote  
control after trying all of the codes listed for your brand,  
or if your brand is not listed at all,try searching for your  
code.  
Setup Codes for DVD Players:  
Denon  
GE  
0490,0634  
0522  
Harman/Kardon  
JVC  
0582  
0558,0623  
0534  
0503  
0539  
0521  
0503,0627  
0571  
0490,0632  
0503,0539  
0525,0571,0632  
0522  
For example,to search for a code for your TV:  
Kenwood  
Magnavox  
Marantz  
Mitsubishi  
Onkyo  
Optimus  
Panasonic  
Philips  
1.  
2.  
Turn on your TV.Set it to the TV mode.  
On the remote control,press and hold SET until  
the LED blinks twice,then release SET.  
3.  
4.  
Enter 9 - 9 - 1.The LED will blink twice.  
Aim the remote control at the the TV and slow-  
ly alternate between pressing POWER and TV.  
Stop when the TV turns off.  
Pioneer  
Proscan  
RCA  
0522  
NOTE: In the search mode, the One For All 4-Device  
Video Expert Plus With Learning remote control will  
send IR codes from its library to the selected compo-  
nent, starting with the most popular code first.  
Samsung  
Sharp  
0573  
0630  
Sherwood  
Sony  
0633  
0533  
Technics  
Theta Digital  
Toshiba  
Yamaha  
Zenith  
0490  
0571  
0503  
0490,0545  
0503,0591  
5.  
6.  
Press SET once to lock in the code.  
To search for the codes of your other compo-  
nents,repeat steps 1 through 5,but substitute  
the appropriate key (i.e.,DVD,VCR,or CBL/SAT)  
for the (DVD/LD,VCR,or Cable/Satellite) com-  
ponent you are searching for.  
Setup Codes for LD Players:  
Aiwa  
0203  
Denon  
Funai  
0059,0172  
0203  
Mitsubishi  
NAD  
0059  
0059  
Optimus  
Panasonic  
Pioneer  
Quasar  
Realistic  
Sony  
0059  
0204  
0059  
0204  
0203  
0193,0201  
0204  
Technics  
22  
23  
 
CHECKING THE CODES  
PROGRAMMING THE MASTER POWER KEY  
FOR ALL ON/OFF  
With the One For All 4-DeviceVideo Expert Plus With  
Learning,you can program the M. POWER key to turn  
your TV,VCR,DVD (or LD),and Cable (or Satellite)  
components on and off with the press of one button.  
If you have set up the One For All 4-DeviceVideo Expert  
Plus With Learning remote control using the Searching  
For Your Code procedure,you may need to find out which  
four-digit code is operating your equipment.For example,  
to find out which code is operating your TV:  
1.  
2.  
Turn on your TV.Set it to the TV mode.  
1.  
On the remote control,press and hold SET  
until the LED blinks twice,then release SET.  
On the remote control,press and hold SET until  
the LED blinks twice,then release SET.  
2.  
3.  
4.  
Enter 9 - 9 - 5.The LED will blink twice.  
Press M.POWER once.  
3.  
4.  
Enter 9 - 9 - 0.The LED will blink twice.  
To view the code for the first digit,press 1 once.  
Count the number of LED blinks (e.g.,3 blinks  
= 3) and write down the number in the left-  
most TV Code box below.  
Enter the following sequence*:  
a. Press TV once.  
b. Press VCR once.  
NOTE: If a code digit is0”, the LED will not blink.  
c. Press DVD once.  
5.  
6.  
Repeat step 4 three more times for remaining  
digits.Use 2 for the second digit,3 for the third  
digit,and 4 for the fourth digit.Finish writing  
down the code in the TV Code boxes below.  
d. Press CBL/SAT once.  
5.  
6.  
Press and hold SET until the LED blinks twice,  
then release SET.  
To check for the codes of your other compo-  
nents,repeat steps 1 through 5,but substitute  
the appropriate key (i.e.,DVD,VCR,or CBL/SAT)  
for the (DVD/LD,VCR,or Cable/Satellite) com-  
ponent you are checking.Write down the codes  
in the appropriate boxes below.  
Now,when you press M.POWER once, the  
remote control will direct power to your TV,  
VCR,DVD (or LD) player,and Cable/Satellite  
component and leave the remote control in the  
TV mode.  
TV Code  
* NOTE: If you do not want all of your equipment to power up  
all of the time, you can shorten step 4 to include only those  
devices you want to turn on or off. For example, to just power  
up your TV and DVD (or LD) player, enter the following  
sequence for step 4:  
DVD (or LD) Code  
a. Press TV once.  
b. Press DVD once.  
Now when you press M.POWER once, the One For All 4-Device  
Video Expert Plus remote control will only direct power to  
your DVD (or LD) player and TV, and still leave the remote  
control in the TV mode.  
VCR Code  
Cable/Satellite Code  
24  
25  
 
RE-ASSIGNING DEVICE KEYS  
CHANGING VOLUME LOCK  
The One For All 4-Device Video Expert Plus With  
Learning remote control can be set up to control a second  
TV or VCR, or any combination of four video compo-  
nents. For example, to have the unit control a TV, a Cable  
Converter, and two VCRs, you will need to re-assign the  
unused DVD key to operate the second VCR as follows:  
The One For All 4-DeviceVideo Expert Plus With  
Learning remote control is preset to control the volume  
of a component through your TV.  
If your TV is not remote controllable,or if you would like  
the volume to be controlled by a different component,you  
can change theVolume Lock setting to control a volume  
through a non-associated mode (e.g.,through the cable in  
the TV mode).  
1.  
On the remote control,press and hold SET until  
the LED blinks twice,then release SET.  
2.  
3.  
Enter 9 - 9 - 2.The LED will blink twice.  
To change Volume Lock to the CBL/SAT mode:  
Press VCR once,then press DVD once.The LED  
will blink twice.  
1.  
2.  
3.  
On the remote control,press and hold SET until  
the LED blinks twice,then release SET.  
4.  
Program the DVD key as a secondVCR.See  
Programming VCR Control on page 12.  
Enter 9 - 9 - 3 and then press CBL/SAT once.  
The LED will blink twice.  
To re-assign other device keys,repeat steps 1 through 4 by  
substituting the key sequence from the following chart for  
a desired component:  
Now,whenever you press VOL +,VOL ,or  
MUTE on the remote control, the volume will be  
controlled by your Cable Converter or Satellite  
Receiver.  
To Re-Assign  
Perform Key Sequence  
SET - 9 - 9 - 2 - TV - VCR  
SET - 9 - 9 - 2 - DVD - VCR  
To change Volume Lock to the VCR mode:  
VCR as 2nd TV key:  
VCR as 2nd DVD key:  
1.  
2.  
3.  
On the remote control,press and hold SET until  
the LED blinks twice,then release SET.  
VCR as 2nd Cbl/Sat key: SET - 9 - 9 - 2 - CBL/SAT - VCR  
Enter 9 - 9 - 3 and then press VCR once.  
The LED will blink twice.  
VCR back to VCR:  
SET - 9 - 9 - 2 - VCR - VCR  
SET - 9 - 9 - 2 - TV - DVD  
SET - 9 - 9 - 2 - VCR - DVD  
DVD as 2nd TV key:  
DVD as 2ndVCR key:  
Now,whenever you press VOL +,VOL ,or  
MUTE on the remote control, volume will be  
controlled by yourVCR.  
DVD as 2nd Cbl/Sat key: SET - 9 - 9 - 2 - CBL/SAT - DVD  
DVD back to DVD SET - 9 - 9 - 2 - DVD - DVD  
To change Volume Lock to the DVD mode:  
:
1.  
2.  
3.  
On the remote control,press and hold SET until  
the LED blinks twice,then release SET.  
CBL/SAT as 2nd TV key: SET - 9 - 9 - 2 - TV - CBL/SAT  
CBL/SAT as 2nd DVD key: SET - 9 - 9 - 2 - DVD - CBL/SAT  
CBL/SAT as 2ndVCR key: SET - 9 - 9 - 2 - VCR - CBL/SAT  
CBL/SAT back to CBL/SAT: SET- 9 - 9 - 2- CBL/SAT- CBL/SAT  
Enter 9 - 9 - 3 and then press DVD once.  
The LED will blink twice.  
Now,whenever you press VOL +,VOL ,or  
MUTE on the remote control, volume will be  
controlled by your DVD (or LD) player.  
Upon completion of a re-assignment,the LED will blink  
twice to confirm your selection.At that time,you will also  
need to program the remote control to control the new com-  
ponent (see previous sections on ProgrammingVCR Control,  
Programming Cable Converter or Satellite Receiver Control,or  
Programming DVD Player Control).  
26  
27  
 
CHANGING VOLUME LOCK (Continued)  
USING KEYMOVER  
The One For All 4-DeviceVideo Expert Plus With  
Learning remote control includes a Keymover feature that  
allows you to map (or copy) keys from one mode (i.e.,  
source mode)to another (i,e,destination mode).  
To change Volume Lock back to the TV mode:  
1.  
2.  
3.  
On the remote control,press and hold SET until  
the LED blinks twice,then release SET.  
Enter 9 - 9 - 3 and then press TV once.  
The LED will blink twice.  
NOTE: The following keys cannot be mapped: TV, DVD, VCR,  
CBL/SAT, SET, M.POWER, V.CONFIG, and learning keys L1~ L4.  
For example,if yourVCR does not have volume control,  
you can map the volume and mute keys from the TV  
mode to the VCR mode as follows:  
Now,whenever you press VOL +,VOL ,or  
MUTE on the remote control, volume will be  
again controlled by your TV.  
1.  
On the remote control,press and hold SET until  
the LED blinks twice,then release SET.  
USING THE MENU KEY  
2.  
3.  
Enter 9 - 9 - 4.  
On your One For All 4-DeviceVideo Expert Plus With  
Learning remote control, the MENU key works just like the  
MENU key of your original remote control and allows you  
to access the on-screen menu of the component you have  
selected (e.g.,TV, VCR, DVD,or CBL/SAT).  
For the source mode,press TV once.  
4.  
5.  
6.  
7.  
8.  
For the source key,press VOL + once.  
For the destination mode,press VCR once.  
For the destination key,press VOL + once.  
When you press MENU,theVOL+,VOL,CH+,and CH –  
keys will allow you to navigate and adjust the on screen  
menu settings just like you would with your original  
remote control.Also, the MUTE key becomes the Menu  
Select key.  
To exit out of the Menu mode, press or EXIT to return to  
normal operation.  
The LED will blink twice indicating the key-  
moved sequence is correct.  
Repeat steps 1 through 7 twice more,substitut-  
ing VOL – and MUTE as source and destination  
keys in steps 4 and 6.  
Upon completion of the above procedure,you can now  
use your One For All 4-DeviceVideo Expert Plus With  
Learning remote control to control the TVs volume and  
mute in theVCR mode,as well as in the TV mode.  
28  
29  
 
USING LEARNING KEYS  
Use the learning keys (L1,L2,L3,L4) to add functions that  
are unique to your home entertainment components  
(e.g.,Tracking Up or Down for aVCR).  
9.  
To test a new feature, press the component  
key (e.g., TV) that was learned once.  
Then press the L key (e.g.,L1) where the com-  
ponents feature was learned.  
NOTE: Please have your original remote controls handy before  
programming learning. Be sure to press each key within 10 sec-  
onds of the previous entry. If not, the remote control will exit the  
programming mode.  
Deleting Functions From The L Keys:  
1.  
On the remote control,press and hold SET until  
the LED blinks twice,then release SET.  
Programming The L Keys  
2.  
3.  
Enter 9 - 7 - 6.The LED will blink twice.  
1.  
On the remote control,press and hold SET until  
the LED blinks twice,then release SET.  
Press the component key once where the  
learned feature to be deleted is stored (e.g.,TV).  
2.  
3.  
Enter 9 - 7 - 5.The LED will blink twice.  
4.  
5.  
Press the L key (e.g.,L1) to be deleted twice.The  
LED will blink twice after the second press.  
Press the component key once in which you  
want to learn a feature (e.g.,TV).  
To clear additional functions stored on other  
L keys,repeat steps 1 through 4.  
4.  
5.  
Press the L key once (e.g.,L1) in which the  
new feature is to be learned.The LED will  
blink rapidly.  
Place your original remote control head to head  
(about 2" apart) from the One ForAll 4-Device  
Video Expert Plus With Learning remote con-  
2"  
trol.  
6.  
On your original remote control,press and  
hold the key (i.e.,feature) to be learned until  
the LED on the One ForAll 4-DeviceVideo  
Expert Plus With Learning remote control  
blinks twice.If the LED does not blink twice,  
stop and repeat steps 1 through 5.  
7.  
8.  
To learn functions on the other L keys, repeat  
steps 3 through 6.  
To lock in new feature(s) on the One For All  
4-DeviceVideo Expert Plus With Learning  
remote control, press and hold SET until the  
LED blinks twice,then release SET.  
30  
31  
 
step 9.  
4.  
USING THE VIDEO CONFIGURATION MODE  
Select a key from Component Group 1 (i.e.,VCR  
or DVD) and press it once.Press PLAY to assign  
Function Group 1 (i.e.,the transport keys).The  
LED will blink twice.  
The One For All 4-DeviceVideo Expert Plus With  
Learning remote control includes a powerful Video  
Configuration feature that allows you to combine the most  
used functions of your Audio/Video equipment into one  
V.CONFIG mode.The features you can combine are orga-  
nized into five groups and can be defined by specific  
modes as follows:  
5.  
6.  
7.  
8.  
9.  
Select a key from Component Group 2 (i.e.,TV,  
VCR,or CBL/SAT) and press it once.Press VOL+  
to assign Function Group 2 (i.e.,the volume  
keys).The LED will blink twice.  
Function Groups  
Function Group 1 Transport Keys (Play, Stop, Fast  
Forward, Rewind, Pause, Record, Forward Scan, and  
Rewind Scan)  
Select a key from Component Group 3 (i.e.,TV,  
VCR,or CBL/SAT) and press it once.Press CH+  
to assign Function Group 3 (i.e.,the channel  
keys).The LED will blink twice.  
Function Group 2 Volume Keys (Volume Up,Volume  
Down,and Mute)  
Select a key from Component Group 4 (i.e.,TV,  
DVD,VCR,or CBL/SAT) and press it once.Press  
MENU to assign Function Group 4 (i.e.,the  
menu keys).The LED will blink twice.  
Function Group 3 Channel Keys (Channel Up,  
Channel Down,Digits 0-9,Enter,Previous Channel,  
Sleep, and Display)  
Function Group 4 Menu Keys (Menu,Up,Down,Left,  
Right, Select, and Exit)  
Select a key from Component Mode Group 5  
(i.e.,TV,VCR,or CBL/SAT) and press it once.  
Press PIP to assign Function Group 5 (i.e.,the  
PIP keys).The LED will blink twice.  
Function Group 5 – PIP Keys (Picture-In-Picture,Swap,  
and Move)  
Component (Mode) Groups  
To lock in the Video Configuration,pressSET  
until the LED blinks twice,then release SET.  
Component Group 1 VCR and DVD  
An Example Video Configuration  
Component Group 2 TV,VCR,and Cable/Sat  
Component Group 3 TV,VCR,and Cable/Sat  
Component Group 4 TV,VCR,Cable/Sat,and DVD  
Component Group 5 TV,VCR,and Cable/Sat  
From one mode,you would like to play your DVD,use the  
Volume control on the TV, change channels on your Cable  
Box,control the Menu on the Cable Box,and use the PIP  
feature of your TV. To program this Video Configuration  
you would perform the following steps:  
To enable the Video Configuration feature,you’ll need to  
perform the following programming sequence:  
1.  
On the remote control,press V.CONFIG once.  
1.  
2.  
On the remote control,press V.CONFIG once.  
2.  
Press and hold SET until the LED blinks twice,  
then release SET.  
Press and hold SET until the LED blinks twice,  
then release SET.  
3.  
4.  
Enter 9 - 7 - 9.The LED will blink twice.  
3.  
Enter 9 - 7 - 9.The LED will blink twice.  
Press DVD once and then press PLAY.The LED  
At this point, you’ll assign Component Groups to Function  
Groups up to five times,depending on how many combi-  
nations you need.You can perform any of the following  
steps in any order,as long as you finish the sequence with  
will blink twice.  
...continued on next page  
32  
33  
 
TROUBLESHOOTING  
PROBLEM: LED does not blink when you press a key.  
USING THE VIDEO CONFIGURATION MODE  
SOLUTION: Replace the batteries with two (2) new AA  
alkaline batteries (see page 7).  
An Example Video Configuration (Continued)  
5.  
Press TV once and then press VOL+.The LED  
will blink twice.  
PROBLEM: LED blinks when you press a key,but home  
entertainment component does not respond.  
SOLUTION: Make sure you are aiming the remote control at  
your home entertainment component and that  
you are within 15 feet of the component you are  
trying to control.  
6.  
Press CBL/SAT once and then press CH+.The  
LED will blink twice.  
PROBLEM: The remote control does not control home enter-  
tainment components or commands are not per-  
forming properly.  
7.  
8.  
9.  
Press CBL/SAT once and then press MENU.The  
LED will blink twice.  
SOLUTION: Try all listed codes for the component brand  
being set up. Make sure all components can be  
operated with an infrared remote control.  
PROBLEM: TV/VCR combo does not respond properly.  
Press TV once and then press PIP.The LED will  
blink twice.  
SOLUTION: Use theVCR codes for your brand. Some combo  
units may require both a TV code and aVCR  
code for full operation (see page 16).  
PROBLEM: No volume on a second TV.  
To lock in the Video Configuration,pressSET  
until the LED blinks twice,then release SET.  
SOLUTION: Follow instructions in Changing Volume Lock  
(see page 27).  
PROBLEM: CH+ , CH, andPREV.CH do not work for your  
RCA TV.  
SOLUTION: Due to RCA design (1983-1987), only the original  
remote control will operate these functions.  
PROBLEM: Changing channels does not work properly.  
SOLUTION: If original remote control required pressing  
ENTER to change channels,press ENTER on the  
remote control after entering a channel number.  
PROBLEM: TriedSearch Methodand still could not find a  
working code.  
SOLUTION: For help,call our technical support group at  
1-330-405-8608 on any business day,between  
9 A.M. and 5P.M.,EST.  
PROBLEM: Remote control does not turn on Sony or Sharp  
TV/VCR Combo.  
SOLUTION: For power on,these products require program-  
ming TV codes on the remote control. For Sony,  
use TV code 0000 andVCR code 0032.For Sharp,  
use TV code 0093 andVCR code 0048.  
34  
35  
 
ADDITIONAL INFORMATION  
The One For All 4-DeviceVideo Expert Plus With  
Learning remote control does not have any user-service-  
able parts.Opening the case, except for the battery cover,  
may cause permanent damage to your remote control.  
©2000 by Universal Electronics Inc.No part of this publi-  
cation may be reproduced,transmitted,transcribed,  
stored in any retrieval system,or translated to any lan-  
guage,in any form or by any means,electronic,mechani-  
cal,magnetic,optical,manual,or otherwise,without the  
prior written permission of Universal Electronics Inc.  
®
One For All is a registered trademark of Universal  
Electronics Inc.  
Part No.URC4880  
8/00  
 

Land Pride Lawn Mower ZXT PRo User Manual
Land Pride Spreader PS15 Series User Manual
Lenovo Computer Monitor LT2223ZWC User Manual
LG Electronics Kitchen Entertainment Center L1717S User Manual
Linear Saw PD300Z 2 User Manual
Magnavox CRT Television 27MS4504 User Manual
Marmitek Home Security System DOORGUARD300TM User Manual
Memorex CD Player MD6810PLL User Manual
Memorex MP3 Player MMP3682 User Manual
Metra Electronics Automobile Accessories 99 5716 User Manual