Mellerware Iron 2200W User Manual

GLOW  
steam  
iron  
_IM.indd  
1
2013/08/13 11:51:13 AM  
 
6. Throw out any excess water after use, once the  
iron has been unplugged.  
3. Fill up the deposit to the top.  
4. Stand the iron upright and plug it in.  
5. Turn the temperature gauge to the *** position.  
6. Let the iron heat up until the pilot light turns off and  
back on again.  
7. Unplug the iron and place it over the sink.  
8. Press the self-cleaning button.  
Steam Ironing  
1. Fill up the iron as described in the section “How to  
fill the water deposit”.  
2. Plug in the iron.  
3. Steam ironing is only possible if you select the  
highest temperature***. Otherwise water may  
seep through the base of the iron.  
4. Wait for the pilot light to go off.  
5. Turn the steam regulator to the desired position  
9. Let the water flow out through the steam vents in  
the base whilst lightly shaking the iron.  
10.Release the self-cleaning button after a moment  
or when the deposit has been emptied  
and place the iron in an upright position.  
6. During pauses and when the ironing is complete, 11.Let the iron cool and then clean it.  
leave the iron standing upright.  
7. Unplug the iron by pulling the plug out of the  
socket. Pour out any leftover water and let the iron  
cool down.  
Maintenance  
Any stains that may form on the base of the iron can  
be cleaned off using a cloth dampened with water  
and white vinegar.  
Spray  
1. The spray can be used when dry ironing or when  
steam ironing.  
2. To do so, press the spray button. The spray button  
has to be pressed repeatedly to release the first  
spray.  
Problems and Solutions  
Should the mains connection fail, do not try to  
replace it since this is potentially dangerous. Take the  
appliance to an authorized Technical Support Service.  
The same applies to any other type of problem. This  
appliance complies with Low Voltage Directive 73/23/  
EC and with Electromagnetic Compatibility Directive  
Steam blast  
The steam blast gives an extra steam jet to help 89/336 EC.  
remove tough creases.  
1. Select the maximum temperature*** on the  
temperature gauge. Wait for the pilot light to go off.  
2. Press the steam blast button. Wait a few seconds  
for the steam to penetrate into the fabric before  
pressing again. For optimum steam quality, do  
not apply more than three successive blasts. The  
SAVE THESE INTRUCTIONS  
THIS PRODUCT IS FOR HOUSEHOLD USE  
ONLY!  
SERVICE  
spray button has to be pressed repeatedly to Before returning your product for service or repair –  
release the first spray.  
check the following:  
Your household mains supply socket is working  
properly.  
Cleaning and Maintenance  
Cleaning  
The mains supply circuit is not overloaded.  
The instructions for use have been followed  
carefully.  
1. Unplug the appliance before proceeding to clean.  
2. Do not use solvents or abrasive products for  
cleaning. A damp cloth with a few drops of  
washing up liquid is enough.  
If service becomes necessary within the guarantee  
period the appliance should be returned to the retail  
outlet where purchased or carefully packed and  
marked “fragile-handle with care“ and sent carriage  
paid to the address below. (Postage is not refundable)  
Service outside the guarantee period is still available  
but this will be chargeable.  
Self-cleaning”  
1. It is important to self-clean the appliance at least  
once a month to remove calcium and any other  
built-up minerals inside the iron.  
2. Place the steam regulator control in the No  
steam position.  
_IM.indd  
3
2013/08/13 11:51:13 AM  
 
TROUBLE SHOOTING  
Problem  
Reason  
Action  
Pre-caution  
Iron is leaking water.  
Temperature is too low  
Set the temperature to steam setting (cotton)  
Check fabric type is suitable for high steam  
temperature  
Steam switch is on self clean  
function  
Turn steam switch setting to steam or 0  
position  
Switch steam setting to 0 (off) after use or  
when filling tank.  
Tank is overfilled  
Empty water tank  
Fill to MAX mark only.  
Iron is in the horizontal position  
too long.  
When adjusting item place iron down in the  
vertical position  
If iron is left on the item in the horizontal  
position for too long it may burn the fabric.  
Check temperature setting is suitable for  
fabric type.  
Iron is not heating up  
Temperature control dial is in  
the off position  
Turn the temperature control dial to the  
desired temperature setting.  
Switch on household socket  
Check the socket with another appliance  
Household socket is off.  
Household socket is not  
working  
Ensure iron is in the upright position.  
Appliance must be of similar wattage to  
prevent overloading.  
Iron is tripping mains  
Overloaded circuit.  
Unplug all appliances attached to the same  
circuit and check iron.  
Note that there can be up to 5 household  
plug sockets on 1 circuit.  
Iron sticking to clothing  
Temperature is too hot  
Turn down temparature on control dial.  
Clean and rinse item.  
Check temperature setting is suitable for  
fabric type.  
Clothing is dirty or not rinsed  
thoroughly.  
Use spray function to dampen item and  
check temperture is correct.  
Use a old linen cloth to remove any trace  
of dirt on the soleplate. Use iron soleplate  
cleaner for bad marks.  
Creases not coming out  
Not Enough Steam  
Item is too dry or temperature  
too low.  
Use steam function.  
Check temperature setting is suitable for  
fabric type.  
The steam control is off or set  
too low.  
Set the steam button/switch to on or full.  
Ensure temperature control dial is set to the  
3 dot position for steaming.  
Check temperature setting is suitable for  
fabric type.  
The iron temperature is  
too low.  
Set temperature control dial to MAX or 3 dot  
position for steaming.  
The steam valve is blocked  
due to water scale.  
If your iron is fitted with a self clean function  
carry out cleaning as per instructions.  
Use distilled or demineralised water in your  
iron to prevent blocking.  
_IM.indd  
4
2013/08/13 11:51:14 AM  
 
_IM.indd  
5
2013/08/13 11:51:14 AM  
 

Lancom Systems Server LCOS 350 User Manual
Lenmar Enterprises Battery Charger R2G02 User Manual
Lincoln Electric Welder 250FG User Manual
Lindy Plumbing Product 32596 User Manual
Mark Levinson Stereo Amplifier N 320S User Manual
Melissa Toaster 243 056 User Manual
Mellerware Fryer 2 7 5 5 01500W User Manual
Metra Electronics Automobile 99 7579 User Manual
Metrologic Instruments Scanner MS7620 User Manual
Midland Radio Two Way Radio GXT800 Series User Manual