Maytag Dishwasher MDB4949SD User Manual

Undercounter Dishwasher  
PRODUCT MODEL NUMBERS  
PRODUCT DIMENSIONS  
MDB4949SD  
MDB5969SD  
MDB6949SD  
MDB7949SD  
MDB8969SD  
Electrical Requirements: 120-volt, 60 Hz, AC-only, 15- or  
20-amp, fused electrical supply. Copper wire only. A  
time-delay fuse or circuit breaker and separate circuit is  
recommended.  
If connecting dishwasher with direct wiring: Use flexible,  
armored or nonmetallic, sheathed  
copper wire with grounding wire  
that meets the wiring  
requirements for your home and local codes and  
ordinances.  
Use a UL Listed/CSA Approved strain relief.  
If connecting dishwasher with a power supply cord:  
Use UL Listed power supply cord  
kit (Part Number 4317824)  
marked for use with dishwashers.  
Power supply cord must plug into a grounded 3-  
prong outlet, located in the cabinet next to the  
dishwasher opening. Outlet must meet all local  
codes and ordinances.  
Water Supply Requirements: A hot water line with 20 to  
120 psi (138 to 862 kPa) water pressure. Water  
temperature must be 120°F (49°C) water at dishwasher.  
Use ³⁄₈" O.D. copper tubing with compression fitting or  
flexible braided water supply line (Part Number  
W10278635RP). Use a 90° elbow with ³⁄₄" hose connection  
with rubber washer (Part Number W10574777). Do not  
solder within 6" (15.2 cm) from water inlet valve. ¹⁄₂"  
minimum plastic tubing is not recommended.  
Drain Requirements: A new drain hose is supplied with  
your dishwasher. If this is not long enough, use a new drain  
hose with a maximum length of 12' (3.7 m) (Part No.  
3385556) that meets all current AHAM/IAPMO test  
standards, is resistant to heat and detergent, and fits the 1"  
(2.5 cm) drain connector of the dishwasher.  
Make sure to connect the drain hose to waste tee or  
disposer inlet above drain trap in house plumbing and 20"  
(50.8 cm) minimum above the floor. It is recommended  
that the drain hose either be  
air gap  
looped up and securely  
fastened to the underside of  
the counter, or be connected  
to an air gap.  
Make sure to use an air gap  
if the drain hose is  
connected to house  
plumbing lower than 20"  
(50.8 cm) above subfloor or  
floor.  
Use ¹⁄₂" (1.3 cm) minimum I.D. drain line fittings.  
If required, the air gap should be installed in accordance  
with the air gap installation instructions. When connecting  
the air gap, a rubber hose (not provided) will be needed to  
connect to the waste tee or disposer inlet.  
Page 1 of 2  
Because Whirlpool Corporation policy includes a continuous commitment to improve  
our products, we reserve the right to change materials and specifications without notice.  
Dimensions are for planning purposes only. For complete details, see Installation  
Instructions packed with product. Specifications subject to change without notice.  
W10649077-D-MT  
5/5/14  
 

Kyocera Telephone KPC680 User Manual
Lanzar Car Audio Stereo Equalizer XE3 User Manual
Lenoxx Electronics Clock Radio CR 501 User Manual
Lenoxx Electronics Thermostat Touchscreen Thermostat User Manual
Logitech Headphones 985 000381 User Manual
Marshall Amplification Stereo Amplifier MG250DFX User Manual
Meade Telescope ETX 80AT BB User Manual
Melissa Frozen Dessert Maker 746 080 User Manual
Midland Radio Weather Radio ER300 User Manual
M Systems Flash Disk Pioneers Flash Memory Flash Memory User Manual