High Performance
K56Plus/V.34+/V.42bis
56K BPS
Plug & Play Internal
FAX/Data Modem
User's Manual
Contents
Section One - Introduction .......................... 1
Section Two - Installation............................ 1
Section Three - AT Command Set .............. 7
Section Four - S Registers........................ 12
Section Five - Result Codes ..................... 14
Section Six - Troubleshooting ................... 15
Section Seven - Support and Service ....... 16
Appendix A - Specifications ..................... 17
Appendix C - Notices ................................ 17
Part #MAN117 Rev. 1.0
K56Plus/HIS-FM
Section One - Introduction
This 56 Kbps* Plug and Play FAX/Data Modem
connects your computer to all popular high speed
modems available today. The modem incorporates
“K56Plus” (56Kbps) technology to provide increased
download speeds using regular telephone lines. The
modem incorporates Plug and Play for ease of instal-
lation.
This manual describes the hardware installation
procedures for your new modem. Additional informa-
tion on AT commands and S-registers is provided so
that your system can be customized for a particular
operating environment.
*Note: K56Plus is capable of downloading at 56Kbps.
However, current FCC regulations limit its speeds to
53Kbps.
Section Two - Installation
This section will provide step by step instructions
on how to install your new 56 Kbps FAX/Data modem.
Installation of this modem product is a three-step
process consists of 1) actual hardware installation, 2)
plug and play configuration, and 3) communication
software installation and configuration.
2.1 Unpacking Your Modem
Be certain that you have all the items listed
below. This package contains:
• A modem
• A telephone cable
• User's manual
•Softwareforthemodem
• Software user's manual
2.2 What You Need
You will need:
1. A phillips-head screw driver
2. A) A Plug and Play enabled Operating System
(e.g., Windows 95),
or
B) APlugandPlayRevision1.0acompliantPC.
1
Proceed to Section 2.3 now if you have every-
thing required.
If you have neither 2A or 2B above, you have two
options to provide Plug and Play functionality to your
PC.
1. Install Windows 95
or,
2. If running DOS or Windows 3.x, configure the
modem using the included modem driver. Instructions
for installing this driver are included in the text file
called README.1ST on the Windows 95 driver disk.
The README.1ST file can be viewed by loading
it into any wordprocessor or any text editor (i.e. DOS
EDIT, NOTEPAD). It may also be viewed by using the
DOS TYPE command. Refer to your word processor
manual or DOS/Windows references for information
on loading text files.
2.3 Hardware Installation
Installation of this modem requires opening and
manipulating your PC. Exercise caution at all times
when working with AC powered and static-sensitive
equipment. Turn off and unplug your PC before instal-
lation. Discharge any static electricity from your body
by touching any bare metal surface of the PC system,
such as its power supply cover.
1. Turn off and unplug your computer from the AC
outlet.
2. Remove your computer's cover (refer to your
computer's owner's manual).
3. Select any available half-card slot, and then re-
move the slot cover (refer to Figure 2-1).
Figure 2-1 Expansion Slots
2
4. Carefully slide the internal modem into the slot
you have chosen, applying even pressure until
the modem is completely seated in the slot.
5. Fasten the retaining bracket with the screw from
the slot cover. Make sure the modem is properly
aligned. Store the slot cover for future use.
6. Replace the computer cover and plug in your
computer.
7. Connect the telephone cable from the modem's
LINE connector to the telephone wall jack.
8. Optionally,connectyourtelephonetothemodem's
PHONE connector.
9. Turn your computer on. Your modem is now
installed.
2.4 Hardware Configuration (Plug and Play)
Your modem is configured using the Plug and
Play (PnP) capabilities of your computer. Plug and
Play is a set of specifications that define the ability for
the computer hardware and operating system to auto-
matically configure all compliant devices that are in-
stalled, relieving the user of the need to determine
whichaddressesandinterruptstouseforeachdevice.
Consult your PC's owner's manual to determine if it is
PnP Revision 1.0a compliant. You most likely have a
Plug and Play Revision 1.0a compliant system if it was
purchased after June 1994 or if the BIOS is dated after
June 1994.
Proceed to one of the following sections, de-
pending on your system's configuration:
• Section 2.4.1 if you are running Windows
95 (with or without a Plug and Play PC)
• Section 2.4.2 if you are running Windows
3.1x or DOS on a PnP-compliant PC.
• Section 2.4.3 if you are running DOS or
Windows 3.1x on a non-PnP PC.
2.4.1 Configuring in Windows 95
The version of Windows 95 you have will deter-
mine which set of dialog boxes is presented to you
when installing the modem in Windows 95. Proceed to
one of the following sections, depending on your
Windows 95's diaglog box:
3
• Section 2.4.1.1 when Windows 95 starts for
the first time after card installation, it
detects the modem and it displays the New
Hardware Found dialog box
• Section 2.4.1.2 when Windows 95 starts for
the first time after card installation, it
detects the modem and it displays the
Update Device Driver Wizard.
2.4.1.1 Windows 95 Release 4.00.950
When Windows 95 starts for the first time after
cardinstallation,itdetectsthemodemanddisplaysthe
New Hardware Found dialog box.
Under New Hardware Found, when asked to
“Select which driver you want to install for your new
hardware,” click on “Driver from disk provided by
hardware manufacturer.” Click “OK.”
The Install From Disk dialog box now instructs
you to “Insert the manufacturer's installation disk into
the drive selected, and then click OK.” Insert the
modem'sdriverdisketteintothediskdriveandtypeA:\
(orB:\ifinsertedindriveB)inthe“Copymanufacturer's
files from:” box. Click “OK.”
Windows 95 may request its own installation
disks or CD-ROM for some files. Insert the Windows
95 disks or CD-ROM as required. When all necessary
filesarecopied, themodemisconfigured. Windows95
will assign the modem a COM port and IRQ line.
Proceed to Section 2.5.
2.4.1.2 Windows 95 Release 4.00.950 B
When Windows 95 starts for the first time after
cardinstallation,itdetectsthemodemanddisplaysthe
Update Device Driver Wizard.
Insert the driver disk into the disk drive and click
“Next.” Windows will find the driver on the driver disk.
Click “Finish. Windows 95 may request its own instal-
lationdisksorCDforsomefiles. InserttheWindows95
disks or CD as required. When all necessary files are
copied, the modem is configured. Windows 95 will
assign the modem a COM port and IRQ line. Proceed
to Section 2.5.
4
2.4.2 Configuring in a Plug and Play System with-
out Windows 95
When this modem is installed in a Plug and Play
system without Windows 95, the computer's BIOS will
assign a COM port and IRQ line to the modem.
Proceed to Section 2.5, Software Installation/
Configuration.
2.4.3 Configuring in a Non-Plug and Play System
ComputerswithoutnativePlugandPlaycapabili-
ties require the use of the included modem driver. If
you have not already installed this driver, refer to the
file README.1ST on the Windows 95 driver disk for
installation and configuration instructions. Once the
driver is installed the modem is enabled and config-
ured during system boot-up. The COM port and IRQ
settings that are assigned to the modem will be dis-
played on the screen as the driver is loaded.
If the PC is running Windows 3.1x, configure
Windows to properly recognize these modem settings
byopeningPROGRAMMANAGER|MAIN|CONTROL
PANEL, click on PORTS and follow Windows 3.1x
user's manual instructions on configuring the installed
modem COM port.
Proceed to Section 2.5, Software Installation/
Configuration.
2.5 Software Installation and Configuration
You are now ready to install and configure the
communicationsoftware.Refertoyoursoftwaremanual
for installation procedures.
Wesuggestthefollowingcommunicationparam-
eters when you first use your data communication
software. Consult the software manual for information
on using these and other parameters/features.
57,600 bps; 8 data bits; no parity; 1 stop bit;
RTS/CTSflowcontrolsetto“on;”initialization
string: AT&F
We suggest that a “Generic Class 1” modem
type should be selected in your fax software.
5
Note that your software must be configured to
communicate with the modem on the same COM port
and IRQ line used by the modem.
2.6 Testing Your Modem After Installation
In order to test your modem you should be
familiar with your communication software. Load and
set up your communication software and enter into
“terminal mode.” Make sure that the COM Port and
IRQ settings of the modem match the software. Type
AT on your terminal screen and press ENTER. You
may see “AT”, “AATT” or nothing on the screen. In any
case, the modem should respond with an OK or 0. If it
does not, either the modem may not have been in-
stalled properly or the software has not been properly
configured. Review Sections 2.2-2.5 and be certain
that the modem and the software have been properly
installed. If required, refer to Section 6 for additional
troubleshooting information.
2.7 Using Your Modem
The communication software included with your
modem product provides a user friendly interface to
accessthefaxanddatafunctionsofyourmodem.This
software should be sufficient for all of your com-
munication needs. There may be times when you
need to access the modem manually via modem
commands. ReadSection3forasummarydescription
of the modem command set before manually access-
ing the modem. You may want to read the software
manual first, however, as the software may already
provide a user friendly method of accessing the func-
tions you need (i.e. dialing or answering calls).
2.8 Where To Go From Here
Youshouldfamiliarizeyourselfwiththefunctions
available from the included software by reading its
manual. You will be accessing most, if not all, of the
modem's functions from this software. You may also
use any other commercially available communication
software with the modem. Read Section 3 only if you
are interested in accessing the modem manually, and
not through the included software. Section 4 and 5
6
contain reference material, and can be skipped. If you
have difficulties getting your modem to work, read
Section 6 - Troubleshooting to find answers to com-
monly asked questions and problems.
Section Three - AT Command Set
3.1 Executing Commands
Commands are accepted by the modem while it
is in Command Mode. Your modem is automatically in
Command Mode until you dial a number and establish
a connection. Commands may be sent to your modem
from a PC running communication software or any
other terminal devices.
Your modem is capable of data communication
at rates of: 300, 1200, 2400, 4800, 9600, 14400,
19200, 28800, 38400, 57600, and 115200 bps. Make
sure your COM port baud rate settings in your commu-
nications software is set to one of the above speeds.
3.2 Command Structure
All commands sent to the modem must begin
with AT and end with ENTER. All commands may be
typed in either upper or lower case, but not mixed. To
make the command line more readable, spaces may
be inserted between commands. If you omit a param-
eter from a command that requires one, it is just like
specifying a parameter of 0. Example:
ATH [ENTER]
This command causes your modem to hang up.
3.3 Basic AT Commands
In the following listings, all default settings are
printed in bold text.
Command
Function
A
Manually answer incoming call.
A/
Repeat last command executed. Do not
precedeA/withATorfollowwithENTER.
B_
B0
CCITT mode
B1
Bell mode
7
D_
0 - 9, A-D, # and *
last number redial
pulse dialing
touch-tone dialing
wait for second dial tone
pause
L
P
T
W
,
@
!
wait for five seconds of silence
flash
;
return to Command Mode after dialing
DS=n
Dial one of the four telephone numbers
(n=0-3) stored in the modem’s non-
volatile memory.
E_
+++
H_
I_
E0
E1
Commands are not echoed
Commands are echoed
Escape Characters - Switch from Data
Mode to Command Mode
H0
H1
Force modem on-hook (hang up)
Force modem off-hook (make busy)
I0
I1
I2
I3
I4
Display product-identification code
Factory ROM checksum test
Internal memory test
Firmware ID
Reserved ID
L_
L0
L1
L2
L3
Low speaker volume
Low speaker volume
Medium speaker volume
High speaker volume
M_
M0
Internal speaker off
M1
Internal speaker on until carrier
detected
M2
M3
Internal speaker always on
Internal speaker on until carrier detected
and off while dialing
N_
N0
Disable Autoscan mode
N1
Enable Autoscan mode
O_
O0
O1
Return to Data Mode
Return to Data Mode and initiate an
equalizer retrain
P
Set Pulse dial as default
Q_
Q0
Modem sends responses
Q1
Modem does not send responses
Sr?
Read and display value in register r.
8
Sr=n
T
Set register r to value n (n = 0-255).
Set Tone Dial as default
V_
V0
Numeric responses
V1
Word responses
W_
W0
Report DTE speed only
W1
Report line speed, error correction
protocol, and DTE speed.
W2
X0
Report DCE speed only
X_
Hayes Smartmodem 300 compatible
responses/blind dialing.
X1
Same as X0 plus all CONNECT
responses/blind dialing
X2
X3
Same as X1 plus dial tone detection
Same as X1 plus busy detection/blind
dialing
X4
All responses and dial tone and busy
signal detection
Y_
Z_
Y0
Modem does not send or respond to
break signals
Modem sends break signal for four
seconds before disconnecting
Y1
Z0
Z1
Reset and retrieve active profile 0
Reset and retrieve active profile 1
3.4 Extended AT Commands
&C_
&C0 Force Carrier Detect Signal High (ON)
&C1 Turn on CD when remote carrier is
present
&D_
&D0 Modem ignores the DTR signal
&D1 Modem returns to Command Mode after
DTR toggle
&D2 Modem hangs up, returns to the
Command Mode after DTR toggle
&D3 Resets modem after DTR toggle
&F_
&G_
&F
Recall factory default configuration
&G0 Guard tone disabled
&G1 Guard tone disabled
&G2 1800 Hz guard tone
&K_
&K0 Disable flow control
&K3 Enable RTS/CTS hardware flow
control
&K4 Enable XON/XOFF software flow control
9
&K5 Enable transparent XON/XOFF flow
control
&K6 Enable both RTS/CTS and XON/XOFF
flow control
&L_
&M_
&P_
&L0 Modem is set up for dial-up operation
&M0 Asynchronous operation
&P0 US setting for off-hook-to-on-hook
ratio
&P1 UK and Hong Kong off-hook-to-on-hook
ratio
&P2 Same as &P0 setting but at 20 pulses
per minute
&P3 Same as &P1 setting but at 20 pulses
per minute
&R_
&S_
&T_
&R0 Reserved
&R1 CTS operates per flow control
requirements
&S0 Force DSR Signal High (ON)
&S1 DSR off in command mode, on in on-line
mode
&T0 Ends test in progress
&T1 Perform Local Analog Loopback Test
&T3 Perform Local Digital Loopback Test
&T4 Grant Remote Digital Loopback Test
request by remote modem
&T5 Deny Remote Digital Loopback Test
request
&T6 PerformaRemoteDigitalLoopbackTest
&T7 PerformaRemoteDigitalLoopbackTest
and Self-Test
&T8 Perform Local Analog Loopback Test
and Self-Test
&V
&V0 Displays Active and Stored Profiles
&V1
Display Last Connection Statistics
&W_
&Y_
&W0 Stores the active profile as Profile 0
&W1 Stores the active profile as Profile 1
&Y0 Configuration Profile 0 active upon
Power on or reset
&Y1 ConfigurationProfile1activeuponPower
on or reset
&Zn=x n=0-3 Store phone number x into non-volatile
RAM
10
%E_
%E0 Disable auto-retrain
%E1 Enable auto-retrain
+MS?
+MS=?
Displays the current Select Modulation
settings
Displays a list of supported Select
Modulation options
+MS=a,b,c,d.e,fSelect modulation where: a=0, 1, 2, 3,
9, 10, 11, 56, 64, 69; b=0-1; c=300-
56000; d=300-56000; e=0-1; and f=0-
1. A, b, c, d, e, f default=56, 1, 300,
56000, 0, 0. Parameter “a” specifies the
modulation protocol desired where:
0=V.21, 1=V.22, 2=V.22bis, 3=V.23,
9=V.32, 10=V.32bis, 11=V.34,
56=K56FLEX, 64=Bell103, and69=Bell
212. Parameter “b” specifies automode
operations where: 0=automode
disabled, 1= automode enabled with
V.8/V.32 Annex A. Parameter “c”
specifies the minimum connection data
rate (300-56000). Parameter “d”
specifies the maximum connection rate
(300-56000); Parameter “e” specifies
the codec type (0=µ-Law, and 1=A-
Law). Parameter “f” specifies “robbed
bit” signaling detection (0=detection
disabled 1=detection enabled)
#CID=n n=0 Disable Caller ID
n=1 Enables Caller ID with formatting (date,
time, number, name)
n=2 Enables Caller ID without formatting
#CID?
Displays current Caller ID mode
#CID=?
Returns Caller ID capabilities of modem.
3.5 MNP/V.42/V.42bis Commands
%C_
%C0 Disable MNP Class 5 and V.42bis data
compression
%C1 Enable MNP Class 5 data compression
only
%C2 Enable V.42bis data compression only
%C3 Enable MNP Class 5 and V.42bis data
compression
11
&Q_
\A_
&Q0 Direct data link only (same as \N1)
&Q5 V.42 data link with fallback options
&Q6 Normal data link only (same as \N0)
\A0
64-character maximum MNP block size
128-character maximum MNP block
size
\A1
\A2
\A3
192-charactermaximumMNPblocksize
256-charactermaximumMNPblocksize
\Bn
\Kn
\N_
Send a 1/10 second line break to the modem,
where n = 1 to 9. At normal connect, the default
is 3
Set break control, where n= 0 to 2. The effect of
this command depends on the modem’s
operating condition. Default is 1.
\N0
\N1
\N2
\N3
\N4
\N5
Normal data-link only
Direct data-link only
V.42 or MNP data link only
V.42/MNP/Normal data link
V.42 data link only
MNP data link only
3.6 Fax Class 1 Commands
+FAE=n
+FCLASS=n
+FRH=n
+FRM=n
+FRS=n
+FTH=n
+FTM=n
+FTS=n
Data/Fax Auto Answer
Service Class
Receive data with HDLC framing
Receive data
Receive silence
Transmit data with HDLC framing
Transmit data
Stop transmission and wait
Section Four - S Registers
Your modem has 41 registers, designated S0
through S95. Table 4-1 shows the registers, their
functions, andtheirdefaultvalues. Someregisterscan
have their values changed by commands. If you use a
command to change a register value, the command
remainsineffectuntilyouturnofforresetyourmodem.
Your modem then reverts to the operating character-
istics specified in its non-volatile memory. Refer to
Section 3 for information on how to use the AT com-
mands to manipulate the S registers.
12
Table 4-1 S - Registers
Function Range/units Default
Register
S0
S1
Auto-answer Ring
Ring counter
0-255 /rings
0-255 /rings
0
0
S2
S3
S4
S5
S6
S7
S8
Escape code character
Carriage return character
Line feed character
Backspace character
Dial tone wait time
0-127 /ASCII
0-127 /ASCII
0-127 /ASCII
0-32, 127 /ASCII
2-255 /seconds
1-255 /seconds
0-255 /seconds
43
13
10
8
2
50
2
Remote carrier wait time
Comma pause time
S9
Carrier detect response time 1-255 /0.1 second
6
S10
S11
S12
S13
S14
Carrier loss time
Touch-tone dialing speed
1-255 /0.1 second
50-255 /milliseconds 95
14
Escape character guard time 0-255 /0.02 second
Reserved
Echo, response, dialing,
originate/answer
Reserved
Modem tests
Reserved
Length of modem tests
50
Bit-mapped register
S15
S16
S17
S18
Bit-mapped register
0-255 /seconds
0
0
S19-20 Reserved
S21
CTS, DTR, DCD, DSR and Bit-mapped register
long space disconnect
S22
S23
Speaker and response
Remote digital loopback
request, data rate, parity
Sleep mode timer
Bit-mapped register
Bit-mapped register
S24
S25
S26
S27
0-255 seconds
0-255 /0.01 second
0
5
1
Data terminal ready delay
RTS to CTS delay interval 0-255 /0.01 second
Asynchronous/Bell/CCITT Bit-mapped register
modes
S28
S29
S30
S31
S32
S33
Pulse dial, make/break ratio Bit-mapped register
Flash time
0-255 /0.01second
0-255 /10 seconds
Bit-mapped register
0-255 /ASCII
0
0
Disconnect timer
Autoscan, EC result code
XON character
17
19
XOFF character
0-255 /ASCII
S34-35 Reserved
S36
S37
S38
S39
S40
LAPM failure options
Reserved
Hang-up delay
Flow control options
MNP options, break types
block modes
Bit-mapped register
7
0-255 /seconds
Bit-mapped register
Bit-mapped register 104
20
3
S41
Compression, retrain
Bit-mapped register 134
S42-45 Reserved
S46
S47
S48
Data compression control
Reserved
V.42 negotiation options
136 or 138
0, 7, or 128
138
7
13
S49-81 Reserved
S82
Break options
3, 7, or 128
128
S83-85 Reserved
S86
Connection failure code
0, 4, 5, 9, 12, 13, 14
S87-S90 Reserved
S91
S92
S95
Transmitattenuation
Fax attenuation
Extended result code optionsBit-mapped register
0-15/dBm
0-15/dBm
10
10
0
Section Five - Result Codes
OK
0
2
4
6
8
CONNECT
1
3
5
7
9
RING
ERROR
NO DIALTONE
NO ANSWER
NO CARRIER
CONNECT 1200
BUSY
CONNECT 600
CONNECT 2400
CONNECT 9600
CONNECT 12000
CONNECT 19200
CONNECT 34000
CONNECT 38000
CONNECT 40000
CONNECT 44000
CONNECT 48000
CONNECT 52000
CONNECT 56000
CONNECT 58000
CONNECT 115200
10 CONNECT 4800
12 CONNECT 7200
14 CONNECT 14400
16 CONNECT 32000
166 CONNECT 36000
168 CONNECT 38400
169 CONNECT 42000
171 CONNECT 46000
173 CONNECT 50000
175 CONNECT 54000
177 CONNECT 57600
178 CONNECT 60000
11
13
15
165
167
17
170
172
174
176
18
179
19 CONNECT 1200TX/75RX 22
CONNECT 75TX/1200RX 23 FAX
33
40
DATA
35 CARRIER 300
CARRIER 1200/75
CARRIER 1200
CARRIER 4800
CARRIER 9600
CARRIER 14400
CARRIER 24000
CARRIER 28800
CARRIER 34000
CARRIER 38000
CARRIER 42000
CARRIER 46000
CARRIER 50000
CARRIER 54000
CARRIER 58000
44 CARRIER 75/1200
46 CARRIER 2400
48 CARRIER 7200
50 CARRIER 12000
52 CARRIER 21600
56 CARRIER 26400
64 CARRIER 32000
151 CARRIER 36000
153 CARRIER 40000
155 CARRIER 44000
157 CARRIER 48000
159 CARRIER 52000
161 CARRIER 56000
163 CARRIER 60000
45
47
49
51
55
57
150
152
154
156
158
160
162
164
COMPRESSION: CLASS 5 66 COMPRESSION: V.42BIS 67
COMPRESSION: NONE 69 PROTOCOL: NONE
70
80
PROTOCOL: LAPM
77 PROTOCOL: ALT
+FCERROR
+F4
14
Section Six - Troubleshooting
This section describes some of the common
problemsyoumayencounterwhileusingyourmodem.
If you can not resolve your difficulty after reading this
chapter, contact your dealer or vendor for assistance.
Modem does not respond to commands.
1. Make sure the communication software is configured
to “talk” to the modem on the correct COM port and
IRQ setting (same COM port and IRQ setting as the
modem). Your communication software must know
which address your modem is using in the system in
order to pass data to it. Similarly, IRQ settings must
be set correctly to receive data from the modem.
2. Make sure that your modem is initialized correctly.
Your modem may have been initialized to not display
responses. You may factory-reset the modem by
issuing AT&F and press ENTER. The factory default
allows the modem to display responses after a com-
mand has been executed.
Modem does not dial.
1. Make sure the modem is connected to a working
phone line. Replace the modem with a working phone
to ensure that the phone line is working.
2. Make sure the phone line is connected to the jack
marked “LINE.” Incorrect connection prevents the
modem from operating properly. Refer to Section 2.3
for modem connection instructions.
Modem dials but does not connect.
1. Make sure the IRQ setting is identical on both the
modem and the software. Modem and software must
be configured identically.
2. Make sure the phone line is working properly. Re-
place the modem with a regular phone and dial the
number. If the line sounds noisy, you may have
difficulty connecting to the remote device.
Modem makes a connection but no data
appears on your screen.
1. Make sure the correct data format (data bits, stop bits,
and parity bits) and flow control (RTS/CTS) are being
15
used.
2. Make sure the correct terminal emulation mode is
being used (see communication software manual).
High pitch tone is heard whenever you
answer the phone.
1. Make sure Auto-Answer is turned off. Your modem is
factory configured to NOT auto-answer. Issue AT&F
to factory reset your modem.
Modem experiences errors while
communicating with a remote modem.
1. Make sure the DTE speed is the same as the modem
connection speed when in Direct Mode.
2. Make sure the remote system and your modem use
the same communication parameters (speed, parity,
etc.).
3. Make sure RTS/CTS hardware flow control is enabled
and XON/XOFF software flow control is disabled in
the communication software.
4. Make sure the data speed is not faster than your
computer's capability. Most IBM compatibles are
capable of 19,200 bps under DOS and Windows 3.X.
Operating at higher speeds under Windows requires
a 486 or faster CPU or Windows 95.
Modem experiences bursts of errors or
suddenly disconnects while communicating
with a remote modem.
1. Make sure Call Waiting is turned off.
2. Make sure the phone line does not exhibit excess
noise.
Section Seven - Support and Service
In the unlikely event you experience difficulty in
the use of this product, we suggest you: (1) consult the
Troubleshooting section of this guide and (2) consult
with your dealer. To obtain service for this product,
follow the Return Merchandise Authorization Proce-
dure as outlined in the Warranty card.
16
Appendix A - Specifications
Communication Std. K56FLEX (56Kbps), V.34,
V.32bis, V.32, V.29, V.27ter,
V.22bis, V.23, V.22, V.21, V.17,
Bell212/103
Data Compression:
Error Correction:
Host Interface:
COM ports:
V.42bis/MNP5
V.42/MNP2-4
16 bit PC bus
1, 2, 3, 4
IRQ lines:
FAX Group:
3, 4, 5, 7, 9, 10, 11, 12, 15
Group III Send/Receive
Standard
FAX Command set: EIA/TIA-578 Service Class 1
Transmit level: -11 dBm +/- 1 dB
Receiver Sensitivity: -39 dBm (V.34); -43 dBm (all
other protocols)
UART:
Data format:
Power:
16550 compatible
300-115200 bps
0.75 W
Temperature:
Caller ID:
PnP:
0 to 55 degrees C (Operating)
Yes
Revision 1.0a
Appendix C - Notices
FCC Compliance
This equipment complies with Part 68 of the FCC Rules. On
this equipment is a label that contains, among other informa-
tion, the FCC registration number and Ringer Equivalence
Number (REN) for this equipment. You must, upon request,
provide this information to your telephone company.
If your telephone equipment causes harm to the telephone
network, the Telephone Company may discontinue your
service temporarily. If possible, they will notify in advance.
But, if advance notice is not practical, you will be notified as
soon as possible. You will be informed of your right to file a
complaint with the FCC.
Your telephone company may make changes in its facilities,
equipment, operations, or procedures that could affect proper
operation of your equipment. If they do, you will be notified in
advance to give you an opportunity to maintain uninterrupted
telephone service.
17
The FCC prohibits this equipment to be connected to party
lines or coin-telephone service.
In the event that this equipment should fail to operate
properly, disconnect the equipment from the phone line to
determine if it is causing the problem. If the problem is with the
equipment, discontinue use and contact your dealer or ven-
dor.
The FCC also requires the transmitter of a FAX transmission
be properly identified (per FCC Rules Part 68, Sec. 68.381 (c)
(3)).
FCC Class B Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the
receiver
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
• Consult the dealer or an experienced radio / TV technician
for help
Notice: 1) Shielded cables, if any, must be used in order to
comply with the emission limits. 2) Any change or modifica-
tion not expressly approved by the Grantee of the equipment
authorization could void the user’s authority to operate the
equipment.
DOC Compliance Information
NOTICE: The Canadian Department of Communications
label identifies certified equipment. This certification means
that the equipment meets certain telecommunications net-
work protective, operational and safety requirements. The
Department does not guarantee the equipment will operate to
the user’s satisfaction.
Before installing this equipment, users ensure that it is
18
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be
installed using an acceptable method of connection. The
customer should be aware that compliance with the above
conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be made by an autho-
rized Canadian maintenance facility designated by the sup-
plier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the tele-
communications company cause to request the user to
disconnect the equipment.
Users should ensure for their own protection that the electri-
cal ground connections of the power utility, telephone lines
and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly
important in rural areas.
Caution: Users should not attempt to make such connec-
tions themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate.
NOTICE: The Load Number (LN) assigned to each terminal
device denotes the percentage of the total load to be con-
nected to a telephone loop which is used by the device, to
prevent overloading. The termination on a loop may consist
of any combination of devices subject only to the requirement
that the sum of the Load Numbers of all the devices does not
exceed 100.
UL Notice
Caution: This internal modem adapter is to be installed in UL
Listedcomputersonly,Alwaysdisconnectthemodemadapter
from the telephone system during installation or when the
cover is removed from the computer.
First Edition
GZ/DR - Version 1.0
19
|