Angle Drill
13 mm (1/2”)
MODEL DA6300
003005
I N S T R U C T I O N M A N U A L
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
w w w. m a k i t a t o o l s . c o m
11. Avoid accidental starting. Be sure switch
is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools
that have the switch on invites accidents.
Electrical Safety
4. Grounded tools must be plugged into an
outlet properly installed and grounded in
accordance with all codes and ordi-
nances. Never remove the grounding
prong or modify the plug in any way. Do
not use any adaptor plugs. Check with a
qualified electrician if you are in doubt as
to whether the outlet is properly
grounded. If the tools should electrically mal-
function or break down, grounding provides a
low resistance path to carry electricity away
from the user.
12. Remove adjusting keys or wrenches
before turning the tool on. A wrench or a
key that is left attached to a rotating part of
the tool may result in personal injury.
13. Do not overreach. Keep proper footing
and balance at all times. Proper footing and
balance enables better control of the tool in
unexpected situations.
14. Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must
be used for appropriate conditions. Ordinary
eye or sun glasses are NOT eye protection.
5. Avoid body contact with grounded sur-
faces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Tool Use and Care
15. Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body is unstable and may lead
to loss of control.
7. Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil,
sharp edges or moving parts. Replace
damaged cords immediately. Damaged
cords increase the risk of electric shock.
16. Do not force tool. Use the correct tool for
your application. The correct tool will do the
job better and safer at the rate for which it is
designed.
8. When operating a power tool outside, use
an outdoor extension cord marked “W-A”
or “W”. These cords are rated for outdoor
use and reduce the risk of electric shock.
17. Do not use tool if switch does not turn it
on or off. Any tool that cannot be controlled
with the switch is dangerous and must be
repaired.
Personal Safety
9. Stay alert, watch what you are doing and
18. Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally.
use common sense when operating
a
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
19. Store idle tools out of reach of children
and other untrained persons. Tools are
dangerous in the hands of untrained users.
10. Dress properly. Do not wear loose cloth-
ing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
20. Maintain tools with care. Keep cutting
tools sharp and clean. Properly maintained
tools with sharp cutting edges are less likely
to bind and are easier to control.
3
21. Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tools
operation. If damaged, have the tool ser-
viced before using. Many accidents are
caused by poorly maintained tools.
SERVICE
23. Tool service must be performed only by
qualified repair personnel. Service or main-
tenance performed by unqualified personnel
could result in a risk of injury.
24. When servicing a tool, use only identical
replacement parts. Follow instructions in
the Maintenance section of this manual.
Use of unauthorized parts or failure to follow
Maintenance instructions may create a risk of
electric shock or injury.
22. Use only accessories that are recom-
mended by the manufacturer for your
model. Accessories that may be suitable for
one tool, may become hazardous when used
on another tool.
USE PROPER EXTENSION CORD: Use only three-wire extension cords that have three-
prong grounding-type plugs and three-pole receptacles that accept the tool's plug. Make
sure your extension cord is in good condition. Replace or repair damaged or worn cord
immediately. When using an extension cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. Table 1 shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the
gage number, the heavier the cord.
Table 1: Minimum gage for cord
Volts
120 V
Total length of cord in feet
Ampere Rating
25 ft.
50 ft.
100 ft.
150 ft.
More Than
Not More Than
AWG
0
6
10
12
6
18
18
16
14
16
16
16
12
16
14
14
14
12
12
10
12
16
Not Recommended
GROUNDING INSTRUCTIONS
This tool should be grounded while in use to protect the operator from electric shock. The
tool is equipped with a three-conductor cord and three-prong grounding type plug to fit the
proper grounding type receptacle. The green (or green and yellow) conductor in the cord is
the grounding wire. Never connect the green (or green and yellow) wire to a live terminal.
Your unit is for use on 120 volts and has a plug that looks like Fig. “A”.
4
An adapter Fig. “B” and “C” is available for connecting Fig. “A” type plugs to two-prong
receptacles. The green-colored rigid ear, lug, etc., extending from the adapter must be con-
nected to a permanent ground, such as a properly grounded outlet box.
GROUNDING METHODS
ADAPTER
GROUNDED
OUTLET
METAL
SCREW
GROUNDED
OUTLET BOX
TAB FOR
GROUNDING SCREW
GROUNDING
PIN
Fig. A
Fig. B
Fig. C
5
SPECIFIC SAFETY RULES
USB001-2
DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to drill safety rules. If
you use this tool unsafely or incorrectly, you can suffer serious
personal injury.
1. Hold tool by insulated gripping surfaces
when performing an operation where the
cutting tools may contact hidden wiring or
its own cord. Contact with a “live” wire
will make exposed metal parts of the tool
“live” and shock the operator.
4. Keep hands away from rotating parts.
5. Do not leave the tool running. Operate the
tool only when hand-held.
6. Do not touch the drill bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
2. Always be sure you have a firm footing.
Be sure no one is below when using the
tool in high locations.
7. Some material contains chemicals which
may be toxic. Take caution to prevent dust
inhalation and skin contact. Follow mate-
rial supplier safety data.
3. Hold the tool firmly.
SAVE THESE INSTRUCTIONS
WARNING:
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
6
FUNCTIONAL
DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
003019
Switch action
CAUTION:
•
Before plugging in the tool, always check to see that the
1
switch trigger actuates properly and returns to the “OFF”
position when released.
2
3
•
Change the direction of rotation only when the tool
comes to a complete stop. Changing it before the tool
stops may damage the tool.
1. Counterclockwise
2. Switch trigger
3. Clockwise
The switch is reversible, providing either clockwise or coun-
terclockwise rotation. To start the tool, simply pull the lower
part of the switch trigger for clockwise or the upper part for
counterclockwise. Release the switch trigger to stop.
003030
Speed change
To change the speed, pull the pin and slide the button to the
“L” position for low speed or the “H” position for high speed. If
the button does not slide easily, turn the chuck slightly in
either direction while sliding the button.
1
2
1. Pin
2. Slide button
7
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
003038
Spade grip
The spade grip can be installed in either of the positions as
shown in the figure. To change the location of the spade grip
from one position to the other, loosen the hex bolts with a
wrench and turn the spade grip to another position. Then
tighten the hex bolts securely.
1
2
1. Spade grip
2. Hex. bolt
003039
003051
Installing or removing drill bit
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each of
the three holes and tighten clockwise. Be sure to tighten all
three chuck holes evenly.
To remove the bit, turn the chuck key counterclockwise in just
one hole, then loosen the chuck by hand.
1
1. Chuck key
8
OPERATION
003074
Holding tool
CAUTION:
1
•
This is a powerful tool. High torque is developed and it is
important that the tool should be securely held and
properly braced.
2
Grasp the switch handle with one hand and the spade grip
with the other hand. When drilling a large hole with a hole
saw, etc., the side grip (auxiliary handle) should be used as a
brace to maintain safe control of the tool.
1. Reaction
2. Forward
003075
When drilling action is forward (clockwise), the tool should be
braced to prevent a counterclockwise reaction if the bit
should bind. When reversing, brace the tool to prevent a
clockwise reaction. If the bit must be removed from a partially
drilled hole, be sure the tool is properly braced before revers-
ing.
1
2
1. Reaction
2. Reverse
Drilling operation
Drilling in wood
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide screw
makes drilling easier by pulling the bit into the workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole, make
an indentation with a center-punch and hammer at the point
to be drilled. Place the point of the bit in the indentation and
start drilling.
Use a cutting lubricant when drilling metals. The exceptions
are iron and brass which should be drilled dry.
CAUTION:
•
•
Pressing excessively on the tool will not speed up the
drilling. In fact, this excessive pressure will only serve to
damage the tip of your bit, decrease the tool
performance and shorten the service life of the tool.
There is a tremendous twisting force exerted on the tool/
bit at the time of hole breakthrough. Hold the tool firmly
9
and exert care when the bit begins to break through the
workpiece.
•
A stuck bit can be removed simply by setting the
reversing switch to reverse rotation in order to back out.
However, the tool may back out abruptly if you do not
hold it firmly.
•
•
Always secure small workpieces in a vise or similar hold-
down device.
Avoid drilling in material that you suspect contains
hidden nails or other things that may cause the bit to
bind or break.
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
001145
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only iden-
tical carbon brushes.
1
1. Limit mark
003085
Use a screwdriver to remove the brush holder caps. Take out
the worn carbon brushes, insert the new ones and secure
the brush holder caps.
1
2
To maintain product SAFETY and RELIABILITY, repairs, any
other maintenance or adjustment should be performed by
Makita Authorized or Factory Service Centers, always using
Makita replacement parts.
1. Screwdriver
2. Brush holder cap
10
ACCESSORIES
CAUTION:
•
These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The
use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding these
accessories, ask your local Makita service center.
•
•
•
Drill bits
Hole saws
Chuck key
11
Memo
12
First-Class
Postage
Required
Post Office will
not deliver
without proper
postage.
Makita U.S.A., Inc.
14930 Northam Street
La Mirada, CA 90638-5753
Fold
MAIL THIS PORTION
Your answers to the following questions are appreciated.
1. This product was purchased from:
3. How did you learn about this product:
Home Center
Other (
)
Magazine
Radio
Hardware/Lumber Store
Tool Distributor
From Dealer
Newspaper
Store Display
Catalog
Exhibition
From Friend
Previous Usage
Other (
Industrial Supply
Construction Supply
)
2. Use of the product is intended for:
4. Most favored points are:
Construction Trade
Industrial Maintenance
Home Maintenance
Hobby
Design
Repair Service
Durability
Power
Features
Size
Price
Other (
)
Other (
)
Makita Brand
5. Any comments:
DATE PURCHASED
MONTH
MODEL NO.
DAY
YEAR
SERIAL NO.
STATUS
SEX
Married Single
M
F
INTL.
LAST NAME / COMPANY NAME
STREET ADRESS
CITY
AREA
CODE
STATE
ZIP CODE
PHONE
40-49
Under 19
20-29
30-39
50-60
Over 60
AGE:
BE SURE TO COMPLETE THE CUSTOMER’S PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.
Please return this portion by facsimile or mail.
Facsimile No: (714) 522-8133
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste
FACTORY SERVICE CENTERS
1-800-4-MAKITA
RETAIN THIS PORTION FOR YOUR RECORDS
ALABAMA
COLORADO
KENTUCKY
NEW MEXICO
PUERTO RICO
2365 Pelham Parkway
Pelham, AL 35124
(205) 620-1791
11839 E. 51st Ave.
Denver, CO 80239-2709
(303) 371-2850
1215 S. Hurstbourne Parkway
Louisville, KY 40222
(502) 326-3740
5805 Menaul Blvd. NE
Albuquerque, NM 87110
(505) 881-4619
200 Guayama St.
Hato Rey, PR 00917
(787) 250-8776
ARIZONA
CONNECTICUT
508 Spring St.
Windsor Locks, CT 06096
(860) 292-6405
LOUSIANA
NEW YORK
TENNESSEE
3707 E. Broadway Rd., Ste. 6
Phoenix, AZ 85040
(602) 437-2850
5626 Jefferson Hwy.
Harahan, LA 70123
(504) 733-4138
4917 Genessee Street
Cheektowaga, NY 14225
(716) 685-9503
4655 Nolensville Rd.
Nashville, TN 37211
(615) 331-9922
131-35 31st Ave.
Flushing, NY 11354
(718) 886-0971
ARKANSAS
FLORIDA
MARYLAND
TEXAS
Shackleford Shopping Center
240 South Shackleford Rd.,
Ste. C
620 Douglas Ave. Suite 1302
Altamonte Springs, FL 32714
(407) 774-6000
7541 - 45 Ritchie Highway
Glen Burnie, MD 21061
(410) 590-0160
12801 Stemmons Fwy Ste. 809
Farmers Branch, TX 75234
(972) 243-1150
Little Rock, AR 72211
(501) 224-5733
NORTH CAROLINA
3501-G S. Tryon St.
Charlotte, NC 28217
(704) 527-0611
750 East Sample Road
Pompano Beach, FL 33064
(954) 781-6333
12701 Directors Dr.
Stafford, TX 77477-3701
(281) 565-8665
MASSACHUSETTS
232 Providence Hwy.
Westwood, MA 02090
(617) 461-9754
CALIFORNIA
41850 Christy St.
Fremont, CA 94538-5107
(510) 657-9881
Thompson Center Waters
5501 W. Waters Ave., Ste. 406
Tampa, FL 33634
3453 IH-35 North, Ste. 101
San Antonio, TX 78219
(210) 228-0676
OHIO
6253 E. Main St.
Columbus, OH 43213
(614) 860-0222
(813) 886-8292
MICHIGAN
1421 N. Clovis Ave., Ste. 112
Fresno, CA 93727
(559) 252-5166
37454 Ann Arbor Trail
Livonia, MI 48150
(313) 432-1012
UTAH
GEORGIA
6379 Pearl Road
Parma Heights, OH 44130
(440) 843-7555
145 E. 1300 S., Ste. 101
Salt Lake City, UT 84115
(801) 359-3410
4680 River Green Parkway
Duluth, GA 30096-2566
(770) 476-8911
14930 Northam St.
La Mirada, CA 90638-5753
(714) 522-8088
MINNESOTA
6427 Penn Ave. South
Richfield, MN 55423
(612) 869-5199
1617 E. Kemper Rd.
Sharonville, OH 45246
(513) 771-0788
VIRGINIA
5760 Northampton Blvd,. Ste.
102
Virginia Beach, VA 23455
(757) 460-0280
1970 Fulton Avenue
Sacramento, CA 95825
(916) 482-5197
HAWAII
4510 Salt Lake Blvd., Suite A7
Honolulu, HI 96818
(808) 847-0038
MISSOURI
OKLAHOMA
1440 South “E” Street
San Bernardino, CA 92408
(909) 885-1289
9876 Watson Road
St. Louis, MO 63126-2221
(314) 909-9889
552 E. Memorial Road
Oklahoma City, OK 73114
(405) 752-2655
ILLINOIS
WASHINGTON
1450 Feehanville Dr.
Mt. Prospect, IL 60056-6011
(847) 297-3100
22220 84th Ave. So., Bldg. A
Kent, WA 98032
(253) 395-8055
7674 Clairemont Mesa Blvd.
San Diego, CA 92111
(858) 278-4471
NEBRASKA
OREGON
4129 S. 84th St.
Omaha, NE 68127
(402) 597-2925
828 19th Avenue., N.W.
Portland, OR 97209
(503) 222-1823
1714 E.McFadden Ave., Unit M
Santa Ana, CA 92705
(714) 667-5066
INDIANA
WISCONSIN
8403 Michigan Road, Unit 1
Indianapolis, IN 46268
(317) 334-9980
Lincoln Plaza Shopping Ctr.
2245 S. 108th St. West Allis, WI
53227
NEVADA
3375 S. Decatur Blvd.
Suites. 22 - 24
Las Vegas, NV 89102
(702) 368-4277
PENNSYLVANIA
Springwater Plaza
364 Wilmington W. Chester
Pike
Glen Mills, PA 19342
(610) 459-4122
1565 Winchester B.
Campbell, CA 95008-0501
(408) 379-0377
(414) 541-4776
KANSAS
8819 W. 95th St.
Overland Park, KS 66212
(913) 642-1111
16735 Saticoy St., Ste. 105
Van Nuys, CA 91406
(818) 782-2440
NEW JERSEY
6200 Babcock Blvd
Pittsburgh, PA 15237
(412) 366-6363
251 Herrod Blvd.
Dayton, NJ 08810-1539
(609) 655-1212
CUSTOMER’S RECORD
Date Purchased
When you need service: Send
complete tool (prepaid) to one
of the Makita Factory Service
Centers listed, or to an Authorized
Makita Service Center. Be sure
to attach a letter to the outside of
the carton detailing the problem
with your tool.
Dealer’s Name & Address
Model No.
Serial No.
15
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of
Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective
workmanship or material, Makita will repair (or at our option, replace) without charge.
This Warranty does not apply where:
• repairs have been made or attempted by others:
• repairs are required because of normal wear and tear:
• the tool has been abused, misused or improperly maintained:
• alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING
AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF
"MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE-YEAR TERM OF
THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary form state to state.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you.
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
883743B069
|