Lincoln Electric Welder US F146 User Manual

US-F146  
11/1/2007  
Date:  
MSDS No.:  
Lincolnweld 880M  
---  
Trade Name:  
Sizes:  
11/1/2004  
Supersedes:  
M A T E R I A L S A F E T Y D A T A S H E E T  
For Welding Consumables and Related Products  
Conforms to Hazard Communication Standard 29CFR 1910.1200 Rev. October 1988  
SECTION I - IDENTIFICATION  
Manufacturer/  
Supplier:  
Product Type: Submerged Arc Flux  
The Lincoln Electric Company  
22801 St. Clair Avenue  
Cleveland, OH 44117-1199  
(216) 481-8100  
Classification:  
AWS F7A8-EM13K-H8 F8P2-ECB2-B2-H8  
F7A8-ENi1K-Ni1-H8 (with LAC-B2)  
F9A6-EA3K-A3-H8 F11A6-ECM2-M2-H8  
F8P8-EA3K-A3-H8  
(with LAC-M2)  
F9A6-EM2-M2-H8 F7A10-ECNi2-Ni2-H8  
F7A6-EH12K-H8  
F7P10-ECNi2-Ni2-H8  
(with LAC-Ni2)  
(with LAC-Ni2)  
SECTION II - HAZARDOUS MATERIAL (1)  
I M P O R T A N T !  
This section covers the materials from which this product is manufactured. The fumes and gases produced during welding with the normal  
use of this product are covered by Section V; see it for industrial hygiene information.  
CAS Number shown is representative for the ingredients listed.  
(1) The term “hazardous” in “Hazardous Materials” should be interpreted as a term required and defined in the Hazards Communication  
Standard and does not necessarily imply the existence of any hazard. All materials are listed on the TSCA inventory.  
TLV  
PEL  
Ingredients:  
CAS No.  
1309-48-4  
1344-28-1  
7789-75-5  
1332-58-7  
1344-09-8  
1317-65-3  
7439-96-5  
7440-21-3  
7439-89-6  
Wt.%  
30  
15  
15  
10  
5
< 5  
1
< 0.5  
< 0.5  
mg/m3  
10  
mg/m3  
15  
Magnesite  
Aluminum oxide and/or Bauxite  
Fluorides (as F)  
Mineral silicates  
10  
15  
2.5  
2.5  
5**  
10*  
10  
5**  
10*  
15  
Silicates and other binders  
Limestone and/or calcium carbonate  
Manganese and/or manganese alloys and compounds (as Mn)*****  
Silicon and/or silicon alloys and compounds (as Si)  
Iron  
0.2  
10*  
10*  
5 (c)  
10*  
10*  
Supplemental Information: (*) Not listed. Nuisance value maximum (*****) Subject to the reporting requirements of Sections  
is 10 milligrams per cubic meter. PEL value for iron oxide is 10 milligrams per  
cubic meter. TLV value for iron oxide is 5 milligrams per cubic meter.  
311, 312, and 313 of the Emergency Planning and  
Community Right-to-Know Act of 1986 and of  
40CFR 370 and 372.  
(**)  
As respirable dust. Value for respirable quartz is 0.05 milligrams per  
cubic meter.  
(c)  
Value is for manganese fume. Present PEL is 5  
milligrams per cubic meter (ceiling value). Values  
proposed by OSHA in 1989 were 1.0 milligrams per  
cubic meter TWA and 3.0 milligrams per cubic meter  
STEL (Short Term Exposure Limit).  
SECTION III - HAZARD DATA  
Non Flammable; Welding arc and sparks can ignite combustibles and flammable products. See Z49.1 referenced in Section VI.  
Product is inert, no special handling or spill procedures required. Not regulated by DOT.  
Rev 4/07  
(CONTINUED ON SIDE TWO)  
 
 

KTM Motorcycle 250 XC F User Manual
LG Electronics Cell Phone B016222 User Manual
LifeSource Blood Pressure Monitor UA 789 User Manual
Lincoln Electric Welder 305D User Manual
Lochinvar Boiler KB 80 thru 285 User Manual
Luxeon Projector D315M User Manual
Magnadyne Car Speaker BT HFKP5 User Manual
Mamp;S Systems Radio Antenna D 360 User Manual
Mattel Doll BLL48 0520G1 User Manual
Melissa Styling Iron 635 087 User Manual