Life Fitness Bicycle C7 User Manual

Life c yc le Exe rc is e Bik e  
A S S E M B L Y I N S T R U C T I O N S  
TM  
 
IMPORTANT SAFETY INSTRUCTIONS !  
Þ DO NOT locate the Lifecycle exercise bike outdoors, near swimming pools, or in areas of  
high humidity.  
Þ DO NOT operate your Lifecycle exercise bike if it has been dropped, damaged, or even  
partially immersed in water. Contact Life Fitness Customer Support Services at the number  
on the back page of this Installation Instruction Guide.  
Þ DO NOT locate the Lifecycle exercise bike any closer than 30 inches ( 76 cm ) to a  
television set.  
Þ DO NOT locate additional Lifecycle exercise bikes any closer than a minimum of 42 inches  
( 107 cm ) from center to center to avoid interference (cross talk) between Heart Rate  
monitors.  
Þ DO keep the area around your Lifecycle exercise bike clear of any obstructions, including  
walls and furniture.  
Þ DO verify the contents of the delivery carton against the accompanying Parts Listing prior to  
setting the cartons and shipping material aside. If any parts are missing, contact Life Fitness  
Customer Support Services at the number listed on the back page of this Installation  
Instruction Guide. Save the shipping cartons in case of return.  
Þ DO read the entire Operation Manual prior to attempting to operate this machine as this is  
essential for proper use.  
 
TOOLS REQUIRED FOR ASSEMBLY... Phillips screwdriver, 1/2” wrench  
PARTS DESCRIPTION  
STABILIZER/HANDLEBAR BOLT  
Qty:5  
Qty: 1  
Qty: 1  
Qty: 1  
2
4
6
8
CONSOLE SCREW  
Qty: 4  
Qty: 1  
Qty: 1  
Qty: 1  
1
3
5
7
0017-00101-0933  
SEAT WITH SEATPOST ASSEMBLY  
0017-00101-1253  
COLLAR  
AK17-00120-0003  
0K18-01156-0001  
DISPLAY CONSOLE ASSEMBLY  
HANDLEBAR ASSEMBLY  
AK18-00215-0000 (Model C7i)  
AK52-00004-0000 (Model C9i)  
STABILIZER BAR  
9V ALKALINE BATTERY  
0017-00003-0757  
AK18-00070-0000  
1
2
1”  
2”  
3”  
4”  
5”  
 
6
8
CAUTION: Improper insertion of the seat  
pin may result in serious injury. Always  
make sure the pin is properly engaged in  
the seat post hole prior to using the  
Lifecycle exercise bike  
5
2
1
4
3
1
7
 
C
1. Before proceeding, familiarize yourself with the parts of the  
Lifecycle exercise bike and make sure that you have received  
all the items described in the Parts List.  
2. Remove the STABILIZER BAR (#7) from the carton base. Use  
the empty CONSOLE CARTON to raise the rear of the  
LIFECYCLE exercise bike as shown.  
Remove the two BOLTS (#1) from the bottom of the SHIPPING  
STABILIZER, save the BOLTS and store the SHIPPING  
STABILIZER with the other shipping containers.  
3. Use the same two BOLTS that held the SHIPPING  
STABILIZER in place to attach the STABILIZER BAR as shown.  
Make certain that the BOLTS are tight and the STABILIZER  
BAR is flush against the frame. Remove the shipping carton.  
A
B
4. Unfold the CONSOLE WIRE HARNESS from the POST  
extending from the FRAME.  
1
7
NOTE: THE COLLAR (#4) SHOULD ALREADY BE IN PLACE  
INSTALLED ON THE HANDLEBAR ASSEMBLY (#5). IF NOT,  
INSTALL BEFORE PROCEEDING.  
8P  
5. Place the HANDLEBAR ASSEMBLY (#5) on the floor in front of  
the FRAME with the two CONNECTORS next to each other.  
Align the two CONNECTORS and push them together until they  
firmly snap into place.  
6. Position the HANDLEBAR ASSEMBLY (#5), with the COLLAR  
(#4) in place, so that the HANDLEBAR is facing away from the  
user. Slide the HANDLEBAR ASSEMBLY into the HANDLEBAR  
POST. Be careful not to pinch the wires.  
Align the three holes in the HANDLEBAR ASSEMBLY (#5), with  
those in the HANDLEBAR POST and install the three  
HANDLEBAR BOLTS (#1).  
NOTE: BE CAREFUL NOT TO DAMAGE THE WIRES WHEN  
PASSING THE BOLTS THROUGH THE HOLES. TIGHTEN THE  
BOLTS SECURELY.  
7. Slide the COLLAR (#4) down until it completely covers the  
HANDLEBAR ASSEMBLY HARDWARE and the HANDLEBAR  
POST. Secure the COLLAR by squeezing the sides and  
pushing downward firmly.  
5
1
5
4
 
6
8. There is a large hole in the rear of the display console (#6)  
through which you can see a 10-pin connector and a 4-pin  
connector. These correspond to the matching connectors on  
the wire harness protruding from the top of the handlebar.  
Model C7i Only: Properly align the locking tabs of the 16-PIN  
CONNECTOR (16P) on the WIRE HARNESS with the 16-PIN  
CONNECTOR on the back of the DISPLAY CONSOLE, then  
snap them together. Next, align the locking tabs of the 3-PIN  
CONNECTOR (3P) on the WIRE HARNESS with the 3-PIN on  
the back of the DISPLAY CONSOLE and plug them together  
until they SNAP into place.  
10P  
16P  
Model C9i Only: Properly align the locking tabs of the 10-PIN  
CONNECTOR (10P) on the WIRE HARNESS with the 10-PIN  
CONNECTOR on the back of the DISPLAY CONSOLE, then  
snap them together. Next, align the locking tabs of the 4-PIN  
CONNECTOR (4P) on the WIRE HARNESS with the 4-PIN on  
the back of the DISPLAY CONSOLE and plug them together  
until they SNAP into place.  
4P  
3P  
8
9. Feed the WIRE HARNESS back into the HANDLEBAR TUBE.  
Attach the DISPLAY CONSOLE (#6) to the HANDLEBAR  
ASSEMBLY using the four CONSOLE SCREWS (#2) and a  
Phillips screwdriver. Tighten the four SCREWS in a crisscross  
pattern.  
CAUTION!: BE CAREFUL NOT TO OVERTIGHTEN  
THE SCREWS.  
D
10. To install the 9-VOLT ALKALINE BATTERY (#8) found in the  
parts bag use a Phillips screwdriver to remove the screw from  
the back door. Gently pull the BATTERY WIRES from the back  
of the DISPLAY CONSOLE and connect them to the 9-VOLT  
ALKALINE BATTERY. Carefully, tuck the BATTERY WIRES  
back into the DISPLAY CONSOLE and set the BATTERY in  
place.  
E
Re-install the BATTERY DOOR by inserting the bottom tab of  
the BATTERY DOOR into the corresponding slot in the  
DISPLAY CONSOLE. Push the DOOR into place and tighten  
the screw with a Phillips screwdriver.  
CAUTION!: BE CAREFUL NOT TO OVER TIGHTEN THE SCREW  
11. After placing the Lifecycle exercise bike in the intended location  
for use, check the stability of the bike.  
If the bike is not level, rotate the FOOT in the STABILIZER BAR  
that appears to be higher until the Lifecycle is level.  
Secure the position of the FOOT by tightening the LOCKNUT  
with the enclosed wrench.  
FOOT  
 
PRE-OPERATION CHECKLIST  
4 Insure that the STABILIZER BAR and HANDLEBAR BOLTS are tight.  
4 Make sure the exercise bike is properly leveled and stable.  
4 Confirm the display console is set to English or metric units.  
(See Optional Settings ENG/MET in Operation Manual.)  
4 Read the entire Operation Manual before using the exercise bike.  
Before attempting to operate your Lifecycle recumbent exercise bike, it is imperative that you familiarize yourself with  
the contents of the Operation Manual. If your recumbent exercise bike does not respond as described in the  
OPERATION MANUAL contact:  
Life Fitness Consumer Division  
14150 Sunfish Lake Blvd.  
Ramsey Minnesota, 55303  
U.S.A  
612.323.4500• FAX: 612.323.4794  
800.328.9714 (Toll-free within the U.S. and Canada)  
Prior to your call, please be sure you have located and noted the  
MODEL NUMBER & SERIAL NUMBER.  
The Model & Serial number information of your Life Fitness recumbent exercise bike is contained in a label located  
under the center of the front stabilizer bar (See previous page).  
Copyright 2000 Brunswick Corporation. All rights reserved. Life Fitness, Lifecycle and Lifepulse are registered trademarks of Brunswick  
Corporation. Any use of these trademarks, without the express written consent of Brunswick Corporation is forbidden.  
M051-00K20-A209  
03/00  
 

Kyocera Cell Phone VMS130 User Manual
Leadstar Group Cordless Sander 5000XB User Manual
Lennox Hearth Stove 506033 19 User Manual
Lightolier Indoor Furnishings 1013CFL User Manual
Logitech Headphones UE 6000 User Manual
Lowrance electronic GPS Receiver AirMap 1000 User Manual
Makita Power Hammer HR2611F User Manual
Marantz Stereo System 541110307024M User Manual
Maytag Washer MFR80PD User Manual
Mellerware Hot Beverage Maker 30J User Manual