Operating instructions
Read the operating instructions before switching on for the first time
Page 6
GB
Commercial refrigerator
7081 203-00
WK/GWK 211
GB
Climate rating
Operating and control elements
Theapplianceissettooperatewithinspecificambienttemperature
limitsaccordingtoitsclimaterating.Thesetemperaturelimitsshould
not be exceeded. The correct climate rating for your appliance is
indicated on the type plate.
Climate rating
Ambient temperature
SN
+10°C to +32°C
+16°C to +32°C
+16°C to +38°C
+16°C to +43°C
N
ST
T
1
2
Temperature display
Temperature setting buttons
The appliance complies with the relevant safety regulations and
EC directives 2004/108/EC and 2006/95/EC.
3
4
Audible warning on/off button
Fan on/off button
5
6
Child-proof lock
On/off button
Setting up
• Avoid positioning the appliance in direct sunlight or near cookers,
radiators and similar sources of heat.
Switching the appliance on and off
• The floor on which the appliance stands should be horizontal and
level.Compensate for uneven floors with the adjustable feet.
• Always ensure that there is good ventilation and that the outward
flowing air is able to escape.
You are recommended to clean the appliance before switching it
on for the first time (see Cleaning). Connect the appliance to the
mains - the appliance is switched on.
• Standard EN 378 specifies that the room in which you install your
appliance must have a volume of 1 m3 per 8 g of R 600a refrigerant
used in the appliance, so as to avoid the formation of inflammable
gas/air mixtures in the room where the appliance is located in the
event of a leak in the refrigerant circuit.The quantity of refrigerant
used in your appliance is indicated on the type plate on the inside
of the appliance.
• To switch the appliance on: Press the ON / OFF button until
the Display lights up.
•To switch the appliance off:Keep the ON / OFF button pressed
for 3 sec. so that the temperature display goes out.
• Do not connect the appliance to the supply with other equipment
using an extension cable - risk of overheating.
Setting the temperature
• Always install the appliance directly against the wall.
To reduce the temperature: Press the DOWN button;
To increase the temperature: Press the UP button.
Dimensions
- While you are entering the temperature, the set temperature will
flash on the display.
- You can change the settings in increments of 1°C briefly pressing
the button again.
- The electronic controls will switch over automatically about 5
seconds after the last time you pressed the button, and the actual
temperature will be displayed.
If F 1appears in the display, the appliance has a fault. Consult your
nearest customer service point.
Fan switch
Thereby a climate which corresponds to that of a wine cellar is
achieved inside the wine cooler. Corks are prevented from drying
out due to an increased level of humidity.
To switch on: Press the Ventilation button.The indicator
lamp in the switch will light up.
To switch off: Press the Ventilation button.The indicator
lamp in the switch goes dark.
Connecting to the mains
Storing wine
Powersupply(a.c.)andvoltageattheoperatingpointmustcomply
with the details on the type plate. The socket must be fused with a
10 A fuse or higher, it must be away from the rear of the appliance
and must be easily accessible.
If you are storing wine for long periods of time, it should be stored
at a temperature of between 10°C and 14°C.
This is the temperature wine cellars are kept at, and it is just right
to allow wine to mature properly.
Connect the appliance with a properly earthed fused plug
The following drinking temperatures are recommended for the
various types of wine.
and socket only.
Red wines: +14°C to +18°C
Rosé wines: +10°C to +12°C
White wines: +8°C to +12°C
Sparkling wines, Prosecco +7°C to +9°C
Champagne +5°C to +7°C
Caution!
The maximum load capacity of the wood racks is 80 kg.
7
Audible warning signal
Air exchange with activated charcoal filter
The audible warning signal helps to protect your wines against
The way in which wines con-
tinuetomaturedependsonthe
ambientconditions.Thequality
of the air is therefore decisive
for preserving the wine.
excessive temperature fluctuations.
- It sounds when the door has been left open for longer than
about60seconds.Theaudiblewarningdeviceisswitched
off by pressing the "Alarm" button.
- It sounds when the interior gets too warm or too cold.The tempera-
ture display will also flash.The audible warning device is switched
off by pressing the "Alarm" button. The temperature display will
continue to flash until the cause of the alarm has been rectified.
We recommend that you re-
place the filter once a year.
Filters can be obtained from
your dealer.
Changing the filter:
Take the filter by the handle.
Turn it 90° to the left or right
and remove.
Additional functions
In set-up mode you can set the child-proof lock and adjust the
brightnessofthedisplay.Thechild-prooflockisdesignedtoprotect
the appliance from being switched off accidentally.
Inserting the filter:
Insertwiththehandleinaverti-
calposition.Turnit90°totheleft
or right until it clicks into place.
Activating set-up mode:
• Press Ventilation button for approx. 5 secs.
- The display shows c for child-proof lock.
Note: The value to be altered flashes.
• Select the required function by pressing the
button:
Up/Down
c = child-proof lock, h = brightness of the display
• Nowselect/acknowledgethefunctionbypressingtheVentilation
button briefly:
> For c = child-proof lock, press the
button to select
Up/Down
Safety lock
Locking the appliance:
• Insert the key as shown by
arrow 1.
c1 = child-proof lock on or
c0 = child-proof lock off and acknowledge with
the Ventilation button.
• Turn the key 90°.
When the symbol is lit, the child-proof lock is
activated.
To unlock the appliance, the
same procedure must be re-
peated in the same order.
> For h = brightness, press the
to select
button
Up/Down
h1 = minimum to
h5=maximumbrightnessandacknowledgewith
the Ventilation button.
Defrosting
Exiting set-up mode:
The appliance defrosts automatically.
Exit the set-up mode by pressing the On/Off button; after 2 min.
the electronic system switches over automatically. The normal
operating mode is activated again.
Cleaning
Before cleaning always switch off the appliance. Pull out the
mains plug or remove/unscrew the fuse.
• Clean the inside, equipment and outer walls with lukewarm water
and a little detergent. Do not use abrasive or acid cleaners or
chemical solvents.
Interior light
Bulbdata: 15 W (neveruse a bulb
ratedatmorethan15W). Thevolt-
age should agree with the details
on the type plate.
Do not use steam cleaners because of the
risk of injury and damage.
Socket: E 14.
• Ensure that no cleaning water penetrates into the electrical com-
ponents or ventilation grille.
Replacing the bulb:
• The dust should be removed from the refrigeration unit and heat
exchanger - metal grid at the back of the appliance - once a year.
• Do not damage or remove the type plate on the inside of the ap-
pliance. It is very important for servicing purposes.
Pull out the mains plug or re-
move/unscrew the fuse.
Change the bulb behind the oper-
ating panel.
8
GB
Malfunctions
You may be able to rectify the following faults by checking
the possible causes yourself:
• Appliance does not function:
– Is the appliance switched on?
– Is the plug correctly fitted in the mains socket?
– Is the socket fuse intact?
3.
Transfer handle to the opposite
side.
• Loud running noise:
– Is the appliance set up firmly on the floor?
– Does the appliance cause nearby items of furniture or objects to
vibrate? Ensure that the appliance is stable and that all parts at
the back can vibrate freely.Please note that noises caused by the
refrigerant circuit cannot be avoided.
• The temperature is not low enough:
– Isthetemperaturesettingcorrect(see„Settingthetemperature“)?
– Doestheseparatelyinstalledthermometershowthecorrectread-
ing?
– Is the ventilation system working properly?
– Is the appliance set up too close to a heat source?
If none of the above causes apply
andyoucannotrectifythefaultyour-
self, contact the nearest customer
servicedepartmentstatingthetype
1
4.
Transfer pin to the opposite side of the
door.
of appliance
, service number
2
3
and appliance number as in-
dicated on the type plate. The type
plate is located in the refrigerator
compartmentontheleft-handside.
5.
Transfer upper hinge components to
the opposite side.
Shutting your appliance down
If your appliance is to be shut down for any length of time, switch it
offanddisconnecttheplugorremovethefuse.Cleantheappliance
and leave the door open in order to prevent unpleasant smells.
The appliance complies with the relevant safety regulations and
EC directives 2004/108/EC and 2006/95/EC.
All types and models are subject to continuous improvement and
the manufacturer therefore reserves the right to make modifica-
tions to the shape, equipment and technology.
6.
Transfer lower hinge bracket to the
opposite side.
Changing over door hinges
1.
7.
Remove screw from lower hinge
bracket.
Locate door on upper pin.
8.
Tilt door inwards from the left 1. Se-
cure hinge pin with screw 2.
2.
Lift door 1, tilt to the right 2 and
remove 3.
9
|