®
PROGRAMMABLE
COMPACT DISC PLAYER
MODEL CD-52
OPERATING INSTRUCTIONS
PLAYS ALL MUSIC COMPACT DISCS
BASS BOOST SYSTEM
6 DIGIT LCD VISUAL DISPLAY
TRACK REPEAT & DISC REPEAT
AC ADAPTOR INCLUDED
DELUXE STEREO HEADPHONES INCLUDED
USES 2 SIZE “AA” BATTERIES (NOT INCLUDED)
AUX OUT JACK - CONNECTS TO YOUR STEREO SYSTEM
(PATCH CORD NOT INCLUDED)
•
•
•
•
•
•
•
•
PLEASE READ CAREFULLY BEFORE USE
CD52(22C-0E7)022100 NL v.1
E
2
LOCATION OF CONTROLS
6
5
4
7
8
3
9
2
10
11
12
1
13
14
1. CD DOOR OPEN BUTTON
2. CD DOOR
15
3. BACKWARD SKIP / SEARCH BUTTON (
4. FORWARD SKIP / SEARCH BUTTON (
5. STOP AND POWER OFF BUTTON
6. REPEAT/RANDOM BUTTON
7. LCD VISUAL DISPLAY
)
)
8. PROGRAM BUTTON
9. PLAY/PAUSE AND POWER ON BUTTON
10. AC ADAPTOR JACK
11. AUX OUT JACK (for home stereo connection)
12. VOLUME CONTROL
13. PHONES JACK (headphone jack)
14. BATTERY DOOR
15. BASS BOOST SWITCH
3
POWER SOURCES
1.Using with Batteries
Insert two size AA alkaline batteries
according to the + and - markings in
the battery compartment.
TIPS ON BATTERY USE
Reversing polarities will damage the batteries and possibly your set. Be sure to
•
•
•
follow polarity ( + and - ) as indicated.
Do not mix different types together (Alkaline, Carbon-Zinc, Nickel-Cadmium etc.),
or old batteries with new ones.
When not in use for an extended period of time, or while internal batteries will not
be used, remove them to prevent possible acid leakage or corrosion resulting in
damage to your player.
When the batteries have become discharged, they must be disposed of in a safe
manner that complies with all applicable laws.
•
•
Installation of batteries should only be done by an adult (for safety).
ALKALINE BATTERY LIFE
Bear in mind that battery life expectancy is based upon volume and bass listening
levels. Maximum battery power consumption happens at maximum settings. Typical
life for 2 size “AA” alkaline batteries is above 8 hours of continuous use.
WHEN THIS SYMBOL
FLASHES IN THE DISPLAY
If the alkaline batteries are weak and discharged, this symbol “
” flashes in the
display, then the power automatically turns off. If this occurs, replace the alkaline
batteries (also if display does not show anything, the batteries are dead).
NOTE: You may use rechargeable batteries on this set. However, because
rechargeable batteries generally have lower voltage (1.2 volts instead of
1.5 volts). Your playing time will be much less than normal fresh alkaline
batteries.
4
2.Using AC Power
Your player may be powered from any household 120V AC outlet, using the AC
adaptor included. Insert the adaptor’s small connector plug into the DC 4.5V Jack
marked
on player (on the right side of the set), and plug the adaptor into
an AC outlet.
NOTE: If the AC Adaptor is connected, and regular batteries are installed, the
player automatically switches to the AC Adaptor power and the batteries
are not used.
CAUTION:
To prevent electric shock, do not use this AC Adaptor with an extension cord or
outlet, unless it can be fully inserted without exposing any part of the blades. Do
not use any other AC adaptor to power this set or you may damage your set.
CONNECTING TO HOME STEREO SYSTEMS
The AUX OUT jack is made to accept a stereo mini plug (3.5mm). Simply connect the
cable’s mini plug to the AUX OUT jack on your player, and the other appropriate end
usually RCA JACKS to the CD/AUX INPUTS of your home stereo.
TO AUX OUT JACK
TO AUX IN JACKS
YOUR
CD PLAYER
OPTIONAL CABLE
3.5mm TO RCA JACKS
YOUR STEREO
SYSTEM
CD PLAYING
5
1 Load the Disc.
Push
here
Disc
Label side up
Slide right to open
2 Connect the Headphones.
Stereo headphones
To PHONES jack
3 Press the PLAY/PAUSE button.
TOTALTRACKS TOTAL PLAYING
TIME ON THE CD
PLAY/PAUSE
button
TRACK NUMBER ELAPSED PLAYING
CURRENTLY TIME OF THE
PLAYING CURRENT TRACK
4 Adjust the Volume.
MAXIMUM
MINIMUM
VOLUME CONTROL
6
Other Operations
Operation
Display window shows
Press
PLAY/PAUSE
button
To pause play
TRACK NUMBER
CURRENTLY PLAYING
PLAYING TIME
FLASHES
To release pause
and resume play
PLAY/PAUSE
button
TRACK NUMBER
CURRENTLY PLAYING
PLAYING TIME
ADVANCES
To stop
STOP button
TOTAL TRACKS
TOTAL PLAYING TIME
STOP button once and wait 30 seconds, or press
STOP button twice
To turn off the power
To skip to the next track(s)
once (or repeatedly)
once (or repeatedly)
To skip to the previous track(s)
To go ahead at high speed
(search)
Keep
depressed and release when the
desired music section of the disc is found.
To go back at high speed
(search)
Keep
depressed and release when the
desired music section of the disc is found.
BASS BOOST switch
This switch enhances the low frequency (bass)
sounds at low listening levels. Switch this ON or
OFF to suit your taste.
BASS BOOST switch
7
REPEAT, INTRO AND RANDOM PLAY
You may have repeat, intro or random play using the REPEAT/RANDOM button.
Press the REPEAT/RANDOM button several times, and the display will show the
followings in turn:
REPEAT
1
--> REPEAT ALL --> INTRO --> SHUFF (RANDOM) --> NORMAL PLAY
Single Track Repeat
Plays one song over and over till you press STOP.
During play, select the song you want to repeat with
X 1
either of the SEARCH buttons (
the REPEAT/RANDOM button once, the symbol REPEAT
appears in the display.
or
), then press
1
REPEAT 1
The song currently playing will repeat over and over,
until you press STOP.
All Tracks Repeat
Repeats all songs in order over and over, till you press
STOP.
X 2
During play, press the REPEAT/RANDOM button twice,
the symbol REPEAT ALL will show in the display.
REPEAT ALL
All songs will keep playing in sequence 1, 2, 3, etc. and
when finished, will start all over again until you press the
STOP button.
Intro Play
This plays the first 10 seconds of every song in
sequential order.
1. During play, press the REPEAT/RANDOM button
three times, the word INTRO will flash in the display.
2. Press the PLAY button, the word INTRO will stop
flashing and the first 10 seconds of each song on the
CD will play in sequential order.
X 3
3. When you find a song you like, press the PLAY button,
normal play will be resumed, that song (and the
following songs) will play NORMALLY.
INTRO
Random Play
This plays the songs on the disc in a random order.
1. During play, press REPEAT/RANDOM button four
times, the word SHUFF will flash.
X 4
2. Press the PLAY button, this will play all of the songs
in random order selected by the CD player. The word
SHUFF will be steady on.
SHUFF
3. Press the SEARCH button
random song.
to skip to the next
8
PROGRAM PLAY
The tracks (songs) on the disc can be programmed (arranged in advance) to play in
any order you prefer (up to 20 tracks can be programmed).
Programming Example:
Program Number
etc.
etc.
1
3
2
5
3
8
4
1
5
2
6
4
7
1
8
1
Track Number (song number)
During programming, the word PROG flashes in the display. To program songs to play
in your preferred order, follow steps below:
1.During play, press the PROGRAM 3.Press the PROGRAM button. Track 3 is
button.
now programmed.
Program #2 will now show in the
display, ready for your next selection of
track.
PROG
The word PROG will flash in the display.
4.Repeat steps 2 and 3 to program other
tracks till you finish (up to 20 selections).
PROG
5.After programming is finished, press
PLAY to begin programmed play.
PROG changes to be steady on in
the display, and music begins to play in
the order you programmed.
Program number
2.Press the SEARCH button (
or
)
to select track number 3 (example). PROG
and track number “03” will flash in the
display.
NOTE:
- The player will stop automatically after
all programmed tracks have been
played.
- To quit programmed play, press STOP
button once. Then you may press PLAY
button to re-start normal play.
PROG
Your programming will be lost:
When the alkaline batteries are
exhausted or removed, or the AC
ADAPTOR is disconnected.
•
Track number
When the power is shut off or the CD
DOOR is opened.
•
9
MAINTENANCE
Handling Compact Discs
Cleaning the lens
Dirty, scratched or warped discs may
cause skipping or noise.
Handle the disc only by the edges. To
keep clean, do not touch its surface.
•
A dirty lens will cause sound skipping. If
the lens is very dirty, the player may not
work. We suggest using a special
cleaning disk (not included) available in
most music and Hi-Fi stores. However, if
you do not have one, you may use a cotton
swab very slightly dampened with alcohol
to clean the lens.
•
Discs should be stored in their cases
after use to avoid scratches.
•
•
Do not expose discs to direct sunlight,
high humidity, high temperatures, or
dust, etc. Prolonged exposure to
extreme temperatures can warp the disc
(such as leaving the discs in your car
during summertime).
Cleaning the cabinet
Wipe with a soft cloth. If the cabinet is
very dirty, dampen (not dripping wet) the
cloth with a weak solution of soapy water,
and then wipe clean.
Do not stick or write anything on either
side of disc. Sharp writing instruments,
or the inks used in some felt-tip pens, may
damage its surface.
•
Cleaning the Discs
To remove the Disc
Fingerprints should be carefully wiped
•
Open the CD DOOR by sliding the DOOR
OPEN button, hold the disc by the edge
while slightly pressing on the center
spindle as illustrated, then lift it from the
edge to release and remove.
from the surface of disc with a soft cloth.
Unlike conventional records, compact
discs have no grooves to collect dust
and microscopic dirt, so gently wiping
them with a soft cloth should remove
most particles. Wipe in a straight
motion from the center to the edge.
NOTE
Always press the STOP button and wait
for the disc to stop rotating before sliding
the DOOR OPEN button to remove the
disc.
Never use thinner, benzine, record
•
cleaner or antistatic spray on a compact
disc. Such chemicals can damage its
plastic surface.
10
SAFETY PRECAUTIONS
Do not take the set apart. The laser beam used in the set may harm your eyes. Refer
servicing to qualified service personnel only.
Do not insert pins or coins, clips, or any objects inside the set.
This set is equipped with a safety device which automatically turns the laser beam off
when the CD DOOR is opened.
Do not drop the set or subject it to strong shocks. Doing so could result in damage.
Do not place the set in locations where the temperature is high, or in humid or dusty
locations, or locations with long heavy vibrations, or tilted surfaces.
The set’s cabinet may warp or the set may be damaged if it is placed in direct sunlight,
near heaters (where the temperature is 1400F/600C or higher) or in cars with the
windows closed. In the summer, the temperature may get as high as 2120F/1000C or
more.
Use the set within a temperature range of 410F/50C to 950F/350C.
Use ONLY the AC Adaptor provided, others may damage your set. Disconnect the
Adaptor from the wall outlet when the set is not to be used for an extended period of
time (3 days or more).
When cleaning your set, use a soft dry cloth. Do not use solvents or commercially
available cleaners, as they may damage or discolor the finish.
Do not wear headphones while operating a motor vehicle. This could create a traffic
hazard and is illegal in many areas. Do not use this set when bicycling or running.
The headphones supplied with your set provide superb stereo listening while allowing
you to hear some outside sounds when listening at normally low volume levels. Listening
at extremely high volume levels minimizes the intrusion of outside noise/sounds. In the
interest of safety, it is strongly advised against the use while engaging in activities
where the exclusion of external sounds (whistles, horns, sirens, traffic, etc.) could be
hazardous. Also loud volume can hurt your ears. If you notice that the sound has
become weak or distorted or if tracks do not change, this is an indication that your
batteries are weak. Replace both batteries at the same time (see Using with Batteries).
Your CD-52 is identified by a serial number located in the Battery Compartment. Record
this number in the space provided below.
Model CD-52 Serial No.
Date Purchased:
This manual contains detailed information on its safety and use. Please read it carefully
so that you may take full advantage of its many features, and ensure a safe reliable
operation. Keep this manual for future reference.
CONDENSATION
If cold water is poured into a glass, water droplets form on the outside of the glass.
This is called condensation. Condensation may occur on internal operating parts of the
lens.
Condensation occurs:
When the set is brought from the cold outdoors into a warm room, or if it is from a cold
room to a room which is heated, or in the summer, if the set is moved from an air-
conditioned room or car to a hot or humid location.
Should condensation occur, the set may not operate properly. Open the CD DOOR
and wait for about 20 minutes (to allow the internal parts to adjust to the surrounding
temperature) before using the set.
11
IMPORTANT REQUIREMENT BY THE FCC
Since the CD circuitry may cause interference to other radios nearby, switch this
set off when not in use or move it away from the affected radios.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesirable operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
•
•
•
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
SAFETY CERTIFICATION
This Compact Disc Player is made and tested to meet safety standards of the FCC
requirements and comply with safety performance of the U.S. Department of Health
and Human Services, and also with FDA Radiation Performance Standards 21 CFR
Subchapter J.
WARNING
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
LASER SAFETY
THIS SET EMPLOYS AN OPTICAL LASER BEAM SYSTEM IN THE CD MECHANISM,
DESIGNED WITH BUILT-IN SAFEGUARDS. DO NOT ATTEMPT TO DISASSEMBLE.
EXPOSURE TO THIS INVISIBLE LASER LIGHT BEAM MAY BE HARMFUL TO HUMAN
EYES. THIS IS A CLASS-1 LASER PRODUCT. USE OF ADJUSTMENTS OTHER THAN
THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS LASER LIGHT BEAM
EXPOSURE. THIS COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR
REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL. THE LASER
MECHANISM IN THE SET CORRESPONDS TO THE STYLUS (NEEDLE) OF A RECORD
PLAYER. ALTHOUGH THIS PRODUCT USES A LASER PICK-UP LENS, IT IS
COMPLETELY SAFE WHEN OPERATED ACCORDING TO DIRECTIONS.
TROUBLE SHOOTING GUIDE
12
Symptoms
Causes
Solutions
Replace both batteries with fresh
alkaline batteries. Battery life with
fresh batteries is above 8 hours of
playing time (rechargeable batteries
have 1/2 of that life).
Batteries are weak (they
may test OK on tester but
they are weak for CD
operation).
Tracks do not
change or set
does not play
normally.
Replace both batteries with fresh
ones.
Dead or weak batteries.
CD Player will not
turn on.
Check AC Adaptor connection at AC
outlet and the right side of set.
AC Adaptor not connected
properly.
Re-insert disc with label side facing
up.
Disc inserted incorrectly.
Try another compact disc.
Close the door securely.
Defective compact disc.
CD DOOR not closed.
Disc will not play.
Take out the CD and leave the CD
DOOR open for about 20 minutes
to dry the moisture condensation.
Moisture has formed inside
the CD deck.
Headphone plug not Re-insert headphone plug into
PHONES jack (not AUX OUT).
inserted properly.
No sound from
headphones.
VOLUME control set to
minimum.
Increase the volume.
Replace with fresh batteries or use
AC Adaptor.
Weak batteries.
Defective compact disc.
Try another compact disc.
Plug headphones into PHONES
jack. (NOT THE AUX OUT JACK)
Headphones plugged into
AUX OUT jack.
VOLUME control
has no function.
Clean or replace the compact disc
or clean the lens.
The compact disc or lens
is dirty or CD is scratched.
Sound is skipping
or sound stops.
Place the CD player on a level
surface that is stable.
Strong vibrations.
Music is too loud.
Lower the VOLUME control.
Sound is distorted. BASS BOOST switch is ON. Slide BASS BOOST switch to OFF.
Replace both batteries or use AC
Adaptor.
Weak batteries.
Remove batteries and Adaptor.
Wait 15 seconds and re-insert.
Make sure batteries are fresh or
Adaptor has power.
Electronic or static error
caused circuitry to lock.
Buttons do not
work.
13
TECHNICAL SPECIFICATIONS
CD Player Section
Frequency response .............................. 20Hz-20KHz
Wow and flutter ...................................... Below measurable limits
Sampling frequency ................................ 44.1KHz
D/A converter ......................................... 1-bit
Error correction method .......................... CIRC
Pickup ................................................... Optical 3-beam semiconductor laser
(780 nm wavelength)
Laser diode material GaAIAs
Laser output less than 44.6mw
General
Maximum output (stereo headphones) .....
Power Supply
20mW + 20mW
AC adaptor ...........................................
DC .......................................................
120V/60Hz
3V: Using 2 size “AA” batteries
Set Dimensions (approximate)
Width ...............................................
Depth ..............................................
Height ..............................................
Weight (approximate) ...........................
5 1/4"
6"
1 1/8"
9.5oz. (270g) (set only)
Because the products are subject to continuous improvement, Lenoxx reserves the
right to modify product designs and specifications without notice and without incurring any
obligation.
For customer service
Dial 1-800-315-5885(MONDAY - THURSDAY 09:00 AM - 5:00 PM, FRIDAY09:00 AM - 1:00 PM EST)
or Visit Our Website: http://www.lenoxx.com
© 2000 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
CD52(22C-0E7)022100 NL v.1
E
|