Lennox Hearth Indoor Fireplace TM 4500 User Manual

HOMEOWNER'S CARE AND  
OPERATION INSTRUCTIONS  
ELITE® SERIES  
45" Wood Burning Fireplaces  
P/N 875,038M REV. N/C 01/2007  
MODEL  
TM-4500  
The information contained in this manual applies to all model fireplaces  
identified on this page. This information will help you obtain safe and  
dependable service from your Lennox fireplace system. Keep this docu-  
ment in a safe place for future reference.  
Before you start your first fire, read this Care and Operations Manual  
carefully to be sure you understand your fireplace system completely.  
Failure to follow these suggestions could result in hazardous operation or  
fireplace malfunction, creating a serious potential for personal injury and/  
or property damage.  
If you have any questions regarding the safe use or operation of your  
fireplace, contact your local Lennox Dealer or your contractor/builder.  
WH Report No. J20054576-231  
RETAIN THESE INSTRUCTIONS  
FOR FUTURE REFERENCE  
 
1. The type of wood used.  
2. How dry it is.  
3. How many logs you put in.  
4. The size of the logs.  
6. Most wood needs to be seasoned 9 to 12  
months to reduce the moisture content and  
produce good steady fires. When moisture  
content is reduced from 60 to 20%, the gain in  
heat potential is nearly 7%.  
Gas Logs  
Ifyourfireplacesystemwasinstalledwithagas  
line, you may wish to install one of two types of  
gas log sets.  
The last statement means that one big log  
weighing 10 pounds has as much heating po-  
tential as 10 pounds of twigs. However, air  
cannot get at the solid log to feed the fire so the  
solid log will burn slowly. While you would get  
the same amount of heat out of either fire, the  
smaller the pieces of wood and the more air  
space around them, the faster the fire will burn.  
7. Proper storage of wood, especially during  
seasoning, is essential. We recommend that  
you:  
This fireplace has been tested and approved for  
usewithadecorativegasapplianceincorporat-  
inganautomaticshut-offdeviceandcomplying  
with the Standard for Decorative Gas Appli-  
ances for installation in vented fireplaces, ANSI  
Z21.60(1991). Decorativegasappliancesmay  
be installed in these fireplaces. Installation  
must be in accordance with the national Fuel  
GasCode,ANSIZ223.1forcompliancewiththe  
revised U.L. 127 Standard.  
a. Never store wood on the ground. This will  
causerottingandinsectinfiltration.Raisewood  
on flat rock or scrap wood.  
b. Stack wood loosely to allow air circulation.  
DISPOSAL OF ASHES  
c. Store wood where it will not be excessively  
exposed to weather, such as under a tarp or  
under a roof.  
Ashes should be placed in a metal container  
with a tight fitting lid. The closed container of  
ashes should be placed on a noncombustible  
floor or on the ground, well away from all  
combustible materials, pending final disposal.  
Iftheashesaretobedisposedofbyburialinsoil  
or other wise locally dispersed, they should be  
retained in the closed container until all cinders  
have thoroughly cooled.  
CAUTION: WHEN USING A DECORATIVE  
GAS APPLIANCE, THE FIREPLACE  
DAMPER MUST BE SET TO THE FULLY  
OPEN POSITION.  
d. Do not stack wood directly against the walls  
of your home.  
These fireplaces have been tested and ap-  
provedtoANSI/IAS/AGAZ21.11.2forusewith  
an unvented gas appliance having a maximum  
rating of 40,000 BTU and complies with the  
StandardforFactory-BuiltFireplaces,U.L.127,  
when installed with unvented gas log sets.  
8. Be a knowledgeable wood buyer. There is a  
difference in cord sizes. A standard cord stack  
of logs is 4 ft. high by 8 ft. long by 4 ft. deep or  
the equivalent of this cubic footage, (Figure 1 ).  
SOFTWOOD VS HARDWOOD  
Standard  
Cord of  
Softwoods contain about 15 percent highly  
flammableresinwhichgeneratescreosotesoot  
in the chimney flue. Burning softwood exclu-  
sively may not be as desirable nor as safe as  
burning denser hardwoods. Many experienced  
fire-builders use small amounts of softwood  
kindling and newspaper in conjunction with  
startingafirewithsplithardwoodlogs.Hereare  
some guidelines to remember:  
Wood  
8'  
Prior to installing any gas log set, (Vented or  
Unvented) refer to the fireplace installation  
instructions for verification of mantle heights  
andplacementofcombustiblematerialsaround  
the firebox opening. NEVER INSTALL AN  
UNVENTED GAS LOG SET WITH A BTU RAT-  
ING GREATER THAN 40,000 BTU. Vented gas  
log sets do not have restrictions placed upon  
their BTU rating.  
4'  
4'  
1.Softwoodsproducefastwarmingandshorter  
fires. Hardwoods burn less vigorously, have  
shorter flames and produce steady, glowing  
coals.  
Wood Fuel Pointers  
Figure 1  
Wood is a wonderful renewable fuel source.  
Normally it burns clean, leaving only a mini-  
mum of waste ash, provides comforting heat  
and can provide a variety of aromas and visual  
images.  
A face cord is the same height and length as a  
standard cord but the depth is only the length  
of the logs (12, 18 or 24 inches). A face cord  
can contain as little as 25% of the wood found  
in a standard cord.  
2. As a general rule, denser woods contain  
morepotentialheatperpound.Mostsoftwoods  
offer moderate heat value per pound.  
3.Differentwoodsvarywidelyinflameheights,  
flame intensities, smoke characteristics and in  
sparking. Most hardwoods do not spark.  
Youwillwanttoknowwhichwoodsarebestfor  
use. Sometimes you may want a quick, short  
fire to offset a morning chill. Soft woods are  
preferable in this case. Other times you would  
want more slow burning and a uniform heat  
output. Hardwoods are preferable for this use.  
If you buy by the ton, remember that wood  
becomes lighter as it dries. When buying green  
or wet wood, ask for some extra poundage to  
allow for the extra water you will be getting.  
4. Most freshly cut “green” wood will not burn  
well and will smoke. Green wood can be from  
10 to 40 percent less efficient than air-dried  
seasoned wood.  
9. When comparing woods of the same mois-  
ture content and same species, we find most  
woods have approximately the same heating  
potential per pound.  
The amount of heat available from the logs will  
be about equal on a weight basis. However,  
logs are generally not weighed so the amount  
of heat will depend on:  
5. Moisture and resin found inside unseasoned  
wood cells will build up pressure under heat  
and explode as sparks.  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.  
3
 
However, most wood is sold by volume, not by  
weight. To determine the best heating source,  
look at the density of various wood types.  
(Density is the weight for a given size.) The  
higher the density, the more potential heat  
output. A standard cord has a volume of 128  
cubic feet. This figure also includes the air  
space between and around the wood. The ac-  
tual volume in a standard cord is between 60  
and 100 cubic feet; depending on how tightly  
the wood is packed.  
4. Build a pyramid of three split logs (split will  
start much faster). Arrange the uneven wood to  
provide plenty of air space between.  
STARTING A FIRE  
1. To start a fire in a the fireplace properly, first  
check the operation of the flue damper.  
5. Now, light the paper at both sides of the  
firebox.  
2. To prevent smoking at start-up, close any  
window located near the fireplace when first  
lighting a fire. The closed windows may be  
reopened once a chimney draft is drawn in the  
fireplace.  
6. Close the screens to prevent the escape of  
sparks and embers.  
7. Close the damper only when your fire is  
completely out and ashes are cold. Keep closed  
whenfireplaceisnotinusetopreventunneces-  
sary loss of heated or cooled air.  
DAMPER CONTROL  
Assumingthatyouarecomparingtwostandard  
cords of different species but the same volume  
and moisture content, the denser species will  
providemoreBTU’s.Thetableofwoodspecies/  
densities reveals more helpful guidelines.  
This fireplace is fitted with a manually con-  
trolledchimneydamper. Thechimneydamper  
should be closed when the fireplace is not in  
use to prevent cold air from entering the home  
through the chimney system.  
GLASS DOOR OPERATING SAFETY  
PRECAUTIONS AND INSTRUCTIONS  
These fireplaces may be equipped with glass  
doors. Refer to the end of this document for a  
listing of the glass doors approved for use with  
these fireplaces.  
HARDWOODS  
DENSITY  
The damper is controlled through the use of a  
control lever located within the firebox open-  
ing at the top center just behind the firebox  
lintel (Figure 2 ).  
Alser, Red  
Ash  
Aspen  
Basswood, American  
Beech, American  
Birch  
.41  
.49-.60  
.38-.39  
.37  
.64  
.55-.65  
.38  
.50  
.43  
.34-.40  
.60.63  
.53  
.60.66  
.69-.75  
.66 (est.)  
.69  
.48-.50  
.48-.63  
.59-.67  
.64-.88  
.42  
WARNING: IF YOUR FIREPLACE IS  
EQUIPPED WITH GLASS DOORS, IT  
SHOULDBEOPERATEDWITHTHEDOORS  
FULLY OPEN OR FULLY CLOSED. IF THE  
DOORSARELEFTPARTIALLYOPEN,GAS  
AND FLAMES MAY BE DRAWN OUT OF  
THEOPENING,CREATINGRISKSOFBOTH  
FIRE AND SMOKE. REFER TO FIGURE 3  
FOR PROPER OPERATING CONDITIONS.  
Push back and up (away from the front of the  
fireplace) to lock the damper blade in the  
OPEN position. To lock the damper in the  
CLOSED position, the damper handle needs  
to be pulled down and forward (towards the  
front of the fireplace).  
Butternut  
Cherry, Black  
Chestnut, American  
Cottonwood  
Elm  
Hackberry  
Hickory, Pecan  
Hickory, True  
Honey locust  
Locust, Black  
Magnolia  
Maple  
Oak, Red  
Oak, White  
Poplar  
Sassafras  
Damper  
Open  
Damper  
Closed  
Lintel  
Combustion  
Air Actuator  
.42  
Sweet gum  
Sycamore, American  
Tanoak  
.52  
.49  
.64 (est.)  
.50  
Tupelo  
Figure 2  
Fully Open or  
Fully Closed  
Walnut, Black  
Willow, Black  
.55  
.39  
The appliance flue damper must always re-  
main open when operating.  
(Bi-Fold Doors)  
SOFTWOODS  
DENSITY  
Figure 3  
3. The grate in the firebox should be centered  
on or over the bottom hearth so your fire can  
breath properly. Crumble and twist plenty of  
newspapers UNDER the grate and criss-cross  
some small dry kindling sticks on top of the  
paper or on the bottom of the grate.  
Bald cypress  
Cedar  
Douglas Fir  
Fir  
Hemlock  
Larch, Western  
Pine  
Redwood  
Spruce  
Tamarack  
.46  
.31-.47  
.46-.50  
.32-.43  
.40-.45  
.52  
.39-.59  
.35-.40  
.35-.41  
.53  
CAUTION: IF A SMOKING CONDITION EX-  
ISTS, GLASSDOORSSHOULDBECLOSED  
DURING FIREPLACE OPERATION.  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.  
4
 
IMPORTANT: Plated polished brass glass  
doors may have a plastic covering over all  
brass pieces for protection during shipping  
and handling. The plastic covering should be  
removedbeforeinstallationoftheglassdoors.  
Under the plastic covering is a protective  
lacquercoatingwhichshouldnotberemoved.  
In some instances, if it is removed, irrevers-  
ible damage to the brass finish could occur.  
Refer to the following for specific information  
on plated polished brass.  
Care and Cleaning of Your Glass Doors  
Combustion Air Control  
Never clean the glass when the doors are hot.  
Do not use ammonia or ammonia based glass  
or household cleaner to clean the glass or the  
door frame. An ammonia based cleaner will  
damage the finish of the glass door.  
The actuator for combustion air system is  
standard on all fireplaces but must not be  
operated if the complete system is not in-  
stalled. See Figure 4 and refer to Figure 2.  
On this Lennox Elite Series fireplace, the con-  
trol lever has been pre-installed. A cover plate  
has been mounted over this control lever only  
if the outside air kit has not been attached. The  
control lever is located on the left hand or  
closed side of the fireplace behind the screen.  
To open the air damper, pull the lever all the  
way out. To close, push the lever all the way in.  
Clean the glass doors by wiping with a damp  
towel followed by a clean dry towel to remove  
streaks.  
Remove stubborn stains from the glass with a  
mild soap solution and a towel dampened with  
clean water. Dry with a clean dry towel.  
IMPORTANT: The lacquer coating on the pol-  
ished brass glass doors and trim pieces can  
be damaged or removed causing corrosion  
and/or tarnish. Do not remove the protective  
lacquer coating from plated polished doors  
and trim. To help protect the finish; use a  
non-acidic wax and avoid the over-spray of  
acidic/alkali based glass cleaners on the  
brass pieces. Please understand that the  
heat of the fire will cause the protective lac-  
querfinishtoslightlychangetoalightcaramel  
color. Do not be alarmed as this is a normal  
occurrence.  
• The fire must always be confined within the  
boundaries of the fuel grate.  
• The fireplace screens must always be closed  
whenever the fireplace is being used.  
Closed  
• Never slam the glass door since it could cause  
the glass to break.  
• Do not build excessively large or hot fires —  
scorching or discoloring of the plated brass  
trim may occur.  
COMBUSTION AIR  
Aproperamountofcombustionairisimportant  
for your fireplace. Fireplaces consume large  
amounts of oxygen.  
Extremetemperaturechangescancauseglass  
breakagedonotbuildahotfireandclosethe  
glass doors if the doors are cold.  
Open  
Figure 4  
It is important to allow an adequate supply of  
air. If the fireplace is not equipped with an  
outside air kit, it may not obtain sufficient  
amounts of combustion air from inside the  
house or structure in which it is installed.  
Therefore, thefiremaydrawfromanoutsideair  
sourceandpullairinthroughthechimney. This  
may cause smoke spillage into the room.  
Ifthetemperedglasspanebecomesscratched  
or chipped, it creates a weakness in the glass  
whichcancausetheglasstobreakwhenheated.  
Replace the pane of glass by contacting your  
nearest dealer.  
WARNING: DO NOT OPERATE THE COM-  
BUSTION AIR ACTUATOR UNLESS A  
COMPLETE OUTSIDE COMBUSTION AIR  
VENT SYSTEM HAS BEEN INSTALLED  
WITH YOUR FIREPLACE.  
CAUTION: GLASS AND METAL FRAMES  
GET HOT — ALWAYS USE HANDLES TO  
OPEN AND CLOSE THE DOORS.  
REFRACTORIES  
Smoke spillage often occurs when a fire is first  
started, until the fireplace and the chimney has  
had the opportunity to “come up to tempera-  
ture” and to begin to function normally. If  
smoke spillage problems persist, a window  
may be opened just a crack to allow the proper  
flow of combustion air to the fireplace.  
All fireboxes contain a furnace refractory floor,  
sides and back. These refractories are rein-  
forcedwithsteel,butcanbebrokenbyimproper  
use. Dropping logs on the bottom refractory  
and building fires directly against the refracto-  
ries can cause premature burnout of these  
components. It may easily be repaired or re-  
placedatcostsfarbelowrepairandmaintenance  
for masonry fireplaces.  
WARNING: BE AWARE THAT SAFETY  
GLASS IS UNPREDICTABLE WHEN HOT  
ANDMAYBREAK,EXPELLINGHOTGLASS  
INTO THE ROOM. ADVISE ALL FAMILY  
MEMBERS TO REMAIN WELL AWAY  
FROM THE FIREPLACE WHEN OPERAT-  
ING WITH DOORS CLOSED TO AVOID  
ANY POSSIBLE PERSONAL INJURY.  
If your fireplace is equipped with an outside  
combustion air kit, keep it open at all times  
when fire is burning and close when fire is out  
to prevent cold air intrusion.  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.  
5
 
Proper care and “burn-in” of the firebox will  
prolong the period of enjoyment without exten-  
sive maintenance. For the first few uses, build  
small fires – not roaring infernos. The materials  
usedintherefractoriescontainandabsorbmois-  
ture. It is important to “cure” the refractories by  
buildingonlymodestfires. Undernormalusage,  
it is expected that hairline cracks will appear in  
the refractory surface. These hairline cracks do  
not affect the safe operation of the fireplace.  
TWICE A YEAR CHECK-UP  
CREOSOTE FORMATION AND REMOVAL  
Normally, twiceayear, youshouldinspectyour  
fireplace following this list:  
When wood is burned slowly, it produces tar  
and other organic vapors, which combine with  
expelled moisture to form creosote. The creo-  
sote vapors condense in the relatively cool  
chimney flue of a slow-burning fire. As a  
result, creosote residue accumulates on the  
flue lining. When ignited, this creosote makes  
an extremely hot fire.  
1. Inspect the opening in your chimney top and  
remove any debris that could clog it. The cap is  
usually held in place by four (4) screws, which  
remove easily for checking or cleaning the full  
length of the flue from above. Remove the  
chimney top while wearing gloves to guard  
against any sharp metal edges.  
The chimney should be inspected at least  
twice yearly during the heating season to de-  
termine if a creosote build-up has occurred.  
MAINTENANCE GUIDELINES  
2. Inspect the entire flue from the top down for  
obstructions such as birds nests, leaves, etc.  
This may be done by using a flexible handled  
chimney cleaning brush. If the chimney con-  
tainsoffset/returnelbows;asoftbrushcleaning  
from the top down to any elbow and then from  
the firebox up to the offset/return section is the  
proper method. The beam from a powerful  
flashlight will help in this inspection.  
Your fireplace is designed to operate trouble-  
freewithminimummaintenance. However, like  
any fine appliance, it deserves and requires  
some housekeeping attention.  
If creosote has accumulated, it should be  
removed to reduce the risk of a chimney fire.  
Ifcreosotebuild-upisfound,donotusechemi-  
cal chimney cleaners that are poured on a hot  
fire. The chemical cleaners can be dangerous  
and generally only work on the flue section  
nearest the fire, leaving the rest of the flue  
unaffected. It is best to take the time to clean  
the flue as previously described or have the  
chimney professionally cleaned by a qualified  
chimney sweep.  
Your fireplace will perform better – and cer-  
tainly look more attractive to family and friends  
– if it is cleaned before each use. Before the first  
seasonal use in Autumn and after the last fire in  
Spring, it is important to inspect the fireplace  
system carefully. We recommend at least two  
complete fireplace inspections a year.  
3. Look up from inside the fireplace (damper  
open) to see any obstructions in the lower flue  
area. If present, shut the damper and glass  
doors (if installed) to seal the firebox and con-  
tain any soot that might fall.  
Before Each Use  
TROUBLESHOOTING  
No Smoking Allowed  
1. Clean the firebox of excessive ashes. Some  
owners prefer to leave a small layer to insulate  
the cold refractory below the grate which helps  
fire starting.  
If your do not have glass doors installed, a  
damp sheet covering the fireplace opening and  
sealedwithmaskingtapewilldo.Thencleanthe  
flue from the top down (if an offset system,  
clean per Step 2) using a proper size chimney  
brush with flexible pole sections. Don’t open  
the doors or remove the sheet until all soot has  
settled. Vacuum, don’t sweep.  
Your new fireplace is designed not to smoke if  
properly installed and operated per our in-  
structions. If you do experience a problem,  
here are several things to check:  
This fireplace has a factory supplied grate at-  
tached, it is permissible to remove the grate for  
cleaning; however, the grate must be re-at-  
tached to the fireplace before the next burn.  
1. Remember – always check to ensure your  
flue damper is in the open position before  
lighting a fire!  
4. Check the metal flashing and seals around  
your chimney. Seal any cracks or loose nail-  
head openings to prevent roof leaks.  
2. Keep the fireplace screens clean so combus-  
tion air flows freely.  
2. When lighting your fire, a little smoke may  
escape into the room – more likely if the  
chimney is cold. To correct this, hold a lighted  
newspaper up inside the firebox near the open  
flue damper. This will turn around any down-  
draft and clear the flue of cold air. As your log  
fire burns below, the updraft will improve as  
the chimney heats up.  
3. Spot check the brick-like refractory for small  
cracks. Heat from the fire expands it slightly.  
When it cools, it contracts.  
5. Clean the firebox thoroughly by using a soft  
brush or equivalent.  
Refractories should be replaced when:  
WARNING: CONTINUED OVER FIRING  
CAN PERMANENTLY DAMAGE YOUR  
FIREPLACE SYSTEM. SOME EXAMPLES  
OF OVERFIRING ARE:  
1. The crack opens more than ¹⁄₄" (19 mm).  
3. Is your fire too far forward? Move it toward  
the back with your poker. Keep the fire well  
within the confines of your fuel grate.  
2. Pitting in the surface is extensive and pits  
become deeper than ³⁄₁₆" (4.76 mm).  
• BURNING QUANTITIES OF SCRAP  
LUMBER, PINEBRANCHES, PAPEROR  
CARDBOARD BOXES WHICH EXCEED  
THE VOLUME OF THE NORMAL LOG  
FIRE.  
3. Any piece of refractory larger than 2" (51  
mm) in radius and ³⁄₁₆" deep becomes dis-  
lodged.  
4. Keep your fire up on the grate and the  
refractory below free of excessive ashes. The  
fire needs plenty of air movement around the  
logs.  
If conditions 1, 2 or 3 occur, the refractory  
should be replaced.  
• BURNING TRASH, CHEMICALS OR  
CHEMICALLY TREATED COMBUS-  
TIBLES.  
6
 
5. If smoking occurs an hour or two after  
lighting the fire, perhaps your well-insulated  
house is too airtight and there is scarcely any  
way for replacement air to enter and feed the  
fire. Check to see if your outside combustion  
air kit (if installed) is open. Check outside to  
ensure no obstructions are in front of exterior  
air entry. Open a window slightly, open doors  
to one or two rooms and see if this stops the  
smoking.  
7. Is your wood fuel too wet or unseasoned?  
Ordoesitcontainsomechemicalsubstancethat  
causes sputtering, smoking and toxic fumes?  
REPLACEMENT PARTS  
A complete parts list is found at the end of this  
manual. Use only parts supplied from the  
manufacturer.  
8. Figure 5 illustrates the correct height of  
yourchimneytop. Itisunlikelythatyourinstal-  
lation does not adhere to the installation  
instructions. However, if not correct, you  
could experience an unusual downdraft. Usu-  
ally,thebestsolutionistoincreasethechimney  
height. This may also be necessary if nearby  
trees, adjoining roof lines or a hill is causing a  
downdraft condition.  
Normally, all parts should be ordered through  
your Lennox dealer. Parts will be shipped at  
prevailing prices at time of order.  
When ordering repair parts, always give the  
following information:  
6. Is a vent fan, exhaust hood or central  
heating/cooling system stealing combustion  
air from your fireplace? If their volume is high  
enough, this can cause negative pressure and  
an unwanted downdraft – and smoking.  
1. The model number of the appliance.  
2. The serial number of the appliance.  
3. The part number.  
4. The description of the part.  
5. The quantity required.  
9. Remember, your fireplace has been de-  
signed as a supplemental heating device only,  
it is not intended to heat your entire home.  
6. The installation date of the appliance.  
Less Than 10' (3m)  
ACCESSORY COMPONENTS  
2' Min. (610mm) 2' Min. (610mm)  
2' Min.  
(610mm)  
3' Min.  
(916mm)  
86L66  
86L67  
86L68  
45ABF  
45ABF-BB  
45ABF-BS  
Figure 5  
Bi-Fold Glass Doors  
WARRANTY  
Bi-Fold Doors  
This fireplace is covered by a limited warranty detailed separately from this document.  
Retain this manual. File it with your other documents for future reference.  
Your fireplace can be fitted with beautiful bi-  
fold doors. Model ABF doors are available for  
use with this fireplace. Doors are easily fitted  
to the fireplace opening. Model ABF doors  
come with standard black finish. Model ABF-  
BB doors have a beautiful bright brass finish.  
Model ABF-BS are made of stainless steel.  
PRODUCT REFERENCE INFORMATION  
We recommend that you record the following important information about your fireplace. Please  
contact your Lennox dealer for any questions or concerns. For the number of your nearest Lennox  
dealer, please call 1-800-9-LENNOX.  
To ensure warranty and to prevent a potential  
fire hazard, do not use any other doors on  
these appliances.  
Your Fireplace's Model Number _______________________________________  
Your Fireplace's Serial Number ________________________________________  
The Date On Which Your Fireplace Was Installed __________________________  
Your Dealer's Name_________________________________________________  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.  
7
 
REPLACEMENT PARTS  
TM-4500  
DESCRIPTION  
Part No.  
Fireplace Assembly  
Firescreen  
16M01  
19M29  
H4539  
H4540  
H4541  
H4013  
H0634  
19M27  
H4006  
H4530  
90L73  
Rod, Screen  
Refractory Clip/Retainer, Rear  
Refractory Clip, Right  
Refractory Clip, Left  
Refractory Spacer, Rear  
Refractory Kit  
Grate  
Grate Bracket Holder  
Door Track  
Touch Up Paint  
The manufacturer reserves the right to make changes at any time, without notice, in design,  
materials, specifications, prices and also to discontinue colors, styles and products.  
Consult your local distributor for fireplace code information.  
Printed in U.S.A. © 2007 by Lennox Hearth Products  
1110 West Taft Avenue  
Orange, CA 92865  
P/N 875,038M REV. N/C 01/2007  
 

Krell Industries Stereo Amplifier KRC HR User Manual
Lenovo Network Hardware 70A69000NA User Manual
LevelOne Network Router WBR 5400 User Manual
Linear Fan 2171 4 User Manual
Lochinvar Swimming Pool Heater CP 992 2072 User Manual
Lochinvar Water Heater CW 0495 User Manual
Lowrance electronic GPS Receiver MapCreate 6 User Manual
Magic Chef Coffeemaker MCECM1NB User Manual
McCulloch Brush Cutter 246 25 cc User Manual
Meridian Audio TV Video Accessories G98 User Manual