ꢀ Bread Baking Machine
KH 1170
Operating instructions
STRASSE 21 · D-44867 BOCHUM
pernass.com
170-08/06-V3
Bread Baking Machine KH1170
Page
Important information for your safety
Device Overview
4
5
Items supplied
6
Correct usage
6
Characteristics
6
Before the First Usage
Before baking
6
7
Control panel
7
Functions of the Bread Baking Machine
Baking bread
9
10
Inserting the ingredients
Inserting the baking mould
Switching on
Programme selection
Timerfunction
Mixing and kneading dough
Allowing the dough to rise
Baking
10
10
10
10
10
11
11
11
12
12
Keeping warm
End of the programme
Cleaning and Care
Technical data
13
13
14
14
14
15
16
Warranty & Service
Disposal
Importer
Temporal progress of the programme
Troubleshooting
Read the operating instructions carefully before using the appliance for the first time
and preserve this booklet for later reference. Hand over the manual to whomsoever
you might pass the appliance on to.
- 3 -
ꢀ
Bread Baking Machine
KH 1170
•
To prevent accidents caused by trip-
ping, the appliance is equipped with
a short power cable.
Only use the appliance inside buil-
dings.
Never place the appliance on or close
to a gas or electric cooker or a hot
oven.
Never cover the appliance with a
tea-towel or any other materials.
Heat and steam must be able to escape.
A fire could occur if the appliance is
covered with an inflammable material
or comes into contact with inflammable
materials, e.g. curtains.
If you use an extension cable, ensure
that the maximum permissible
power rating of the cable corresponds
at least with that of the bread maker.
Place the extension cable in such a
way as to prevent anyone from trip-
ping over it or inadvertently pulling
on it.
Always check the power cable and
the plug before use. Should the
power cable of the appliance become
damaged, for the sake of safety it
must be replaced by the manufacturer,
the manufacturer's customer service
or a similarly qualified person.
The use of ancillaries not recommen-
ded by the manufacturer could cause
damage. Use the appliance only for
its intended purposes. Non-compliance
invalidates all warranty claims.
Start a baking programme only
when a baking mould is fitted in.
•
If children are in the vicinity, supervise
the appliance particularly well!
If the appliance is not in use, and
also before cleaning, remove the
plug from the power socket. Allow
the appliance to cool down before
removing individual parts.
Children should only be permitted
to use electrical appliances or stand
close to them when they are under
the supervision of an adult.
This appliance complies with the
requirements of all relevant safety
regulations. Inspection, repair and
technical maintenance may only be
performed by qualified specialists.
The warranty will become void in
cases of non-compliance.
Do not place any objects on the
appliance and do not cover it during
operation. Risk of Fire!
Caution: The bread maker becomes
very hot during operation. Do not
touch the appliance until it has cooled
down, or use oven gloves.
Before inserting or removing ancilla-
ries, allow the appliance to cool
down and unplug the power cable.
Do not transport the Bread Baking
Machine if the baking mould con-
tains fluid or hot contents, e.g. jams.
Risk of Burns!
Avoid coming into contact with the
rotating kneading paddles during
use. Risk of injury!
Do not pull on the cable, rather,
remove the plug from the socket.
When not in use, and before cleaning
the appliance, remove the power
cable from the plug.
•
•
Never place the bread machine in
water or other liquids. Risk of fatal
electrical shocks!
Do not clean the appliance with
abrasive sponge cleaning pads.
Should particles break away from
the sponge and come into contact
with electrical components, you
could receive an electric shock.
ƽ Important information for your
•
•
safety
•
•
Please read the operating instruc-
tions through completely before
using the appliance for the first
time!
Danger of suffocation! Children can
suffocate through the improper use
of packaging materials. Dispose of
these immediately after unpacking
or store them in a place that is out
of reach of children.
•
•
•
Device Overview
ᕡ
ᕢ
»
¿
ᕥ
²
¶
º
¾
Handle
Appliance lid
Viewing window
Baking mould
Kneading paddles
Control panel
Display
•
•
•
•
After unpacking, check the bread
maker for signs of transport damage.
If necessary, contact your supplier.
Place the appliance on a dry, flat
and heat-resistant surface.
Do not place the appliance close
to gas burners, electrical cookers
or other sources of heat.
•
•
•
•
Ventilation slots
Baking space
CAUTION! Hot surfaces!
This symbol on the lid of your bread
maker warns you about the risk of
burns.
•
Do not place the appliance close
to inflammable materials or explosive
and/or ignitable gases. A minimum
distance of 10 cm must be maintained
to all other materials.
•
•
Overview - Control panel
•
•
Ensure that the ventilation slots of
the appliance are not covered.
Before plugging the appliance in,
check that the electricity type and
mains voltage matches the informa-
tion given on the type plate.
Ạ
ạ
Ả
Button - Start/Stop
Button - Level of browning
Button - Dough Volume
Level I: 700 - 950 gr.
Level II: 950 - 1250 gr.
Button - Select
•
•
•
ả
Ấ
•
Do not lay the power cable over
sharp edges or close to hot surfaces
or objects. They could damage the
insulation of the power cord.
•
•
Button - Time
Accessories
Measuring beaker
Kneading paddles
•
Do not use the Bread Baking Machine
for the storage of foods or utensils.
Measuring spoon
Kneading paddle remover
- 4 -
- 5 -
ꢀ
ꢀ
Items supplied
Before the First Usage
ƽ Danger of fire! DO NOT allow the
Bread Baking Machine to heat up
for longer than 5 minutes with an
empty baking mould ᕤ. There exists
a real danger of overheating.
Control panel
Bread Baking Machine KH 1170
2 Kneading paddles
Baking mould
Measuring beaker
Measuring spoon
Kneading paddle remover
Operating instructions
Concise instruction sheet
Order card
Disposal of the packaging material
Unpack your appliance, remove all trans-
portation restrainers and dispose of the
packaging material as per the current
regulations for your locality.
ᕧ Display
Basic adjustments
The basic adjustments are shown as soon
as the appliance is connected to a power
source. This display signalises operational
readiness. It corresponds to the pro-
gramme NORMAL:
Before baking
Initial cleaning
Wipe the baking mould ᕤ, kneading
paddles ᕥ and upper surfaces of the
Bread Baking Machine with a clean
moist cloth before taking it into use for
the first time. Do not use any abrasive
materials or cleaning powders. Remove
the protective foil from the display ᕧ.
For a successful baking process, please
consider the following factors:
•
Appearing in the display is „1 3:30“.
The „1“ shows which programme is
currently valid, „3:30“ is the pro-
gramme period in hours and minutes.
The positions of two arrows on the
upper edge of the display give infor-
mation about the selected level of
browning (left arrow) and the volume
(right arrow). The basic adjustments
when switching on are: „Level II“
(Bread weight 950-1250 gr) and
„Medium Browning“.
Recipe book
•
Remove the baking mould ᕤ from
the housing before filling it with
ingredients. Should ingredients drop
into the baking area, a fire may be
caused by them burning on the
heating elements.
Correct usage
•
Use the Bread Baking Machine only for
baking bread and only in domestic areas.
Do not use the appliance for drying
foodstuffs or other objects.
Do not use the Bread Baking Machine
outdoors.
Use only the ancillaries recommended
by the manufacturer.
Non-recommended ancillaries may cause
damage to the appliance.
Preheating
ꢀ Please take note of the following
notice regarding the first usage:
•
•
Place ingredients into the baking
mould ᕤ in the sequence specified.
All ingredients should have room
temperature, to ensure an optimal
rising result from the yeast.
For the first heating up ONLY, place the
empty baking mould ᕤ into the applian-
ce. Close the appliance lid ᕢ. Select the
programme BAKE, as described in the
chapter „Baking bread“, and press the
button Start/Stop Ạ to warm up the
appliance for 5 minutes. Afterwards, to
stop the process press the button
Start/Stop Ạ until a signal tone is heard.
As the heating elements are lightly greased,
a slight smell may occur when first put-
ting it into operation. This is harmless
and stops after a short time. Provide for
sufficient ventilation, for example, open
a window. Allow the appliance to cool
down completely and once again wipe
the baking mould ᕤ, kneading paddles
ᕥ and the outer surfaces of the Bread
Baking Machine with a clean moist
cloth.
•
Measure the ingredients precisely.
For this, use for example the supplied
measuring implements . With
three different scales on the measu-
ring beaker , Milliliter (ml), Oun-
ces (oz) and cups (CUP), you can mea-
sure out the ingredients in three
measurement systems. Even negligi-
ble deviations from the quantities
specified in the recipe may affect
the baking results.
During operation, the programme
progress can be read off from the back-
wards running time countdown in the
display.
Characteristics
With the Bread Baking Machine you
have the possibility to bake bread accor-
ding to your taste.
•
•
•
You can choose from 10 different
baking programmes.
You can employ ready-to-use baking
mixtures.
You can knead dough for bread rolls
and make jams.
ƽ Note
Never use quantities larger than those
specified. Too much dough can overflow
from the baking mould ᕤ and, with direct
contact to the hot heating elements, cause
a fire.
- 6 -
- 7 -
ꢀ
ꢀ
Ạ Button - Start/Stop
Ả Button - Dough Volume
5.Programme WHOLEWHEAT
For wholewheat breads.
•
During the keep-warm phase at the
end of the baking process the signal
tone sounds several times in succes-
sion.
•
To start and stop the programme,
press the button Start/Stop Ạ.
With the programmes 1. NORMAL,
5. FULL-CORN and 10. LOOSE the bread
weight can be varied with the button
Dough Volume Ả :
•
As soon as the button Start/Stop Ạ
is pressed, the double-point between
the time display starts to flash.
6. Programme CAKE
For pastries that will be baked with
baking powder.
Repeat function
•
With the button Start/Stop Ạ you
can break off the programme in any
position: Hold the button Start/Stop
Ạ pressed until a signal tone can be
heard. In the display ᕧ the begin
position of the above-named start
programme appears. Should you
wish to use a different programme,
select it with the button Select ả.
LEVEL I = for a smaller bread weight
700-950 grammes
LEVEL II = for a larger bread weight
950-1250 grammes
Should there be an electricity power
cut of more than 10 minutes the Bread
Baking Machine must be started anew.
This is only practicable if the dough, at
the time of interruption in the programme
process, had not passed beyond the
kneading process.
In all other cases, one must start again
from the beginning! With electricity
power cuts of less than 10 minutes dura-
tion the programme continues itself
automatically from the appropriate posi-
tion (see chapter „Memory function“).
7. Programme DOUGH
For the production of dough. This pro-
gramme kneads the ingredients and
allows the dough to rise. It is not baked.
The programme DOUGH is suitable for
the production of pastry for pizza, for
example.
ả Button - Select
Press the button ả, to switch through
the various programmes described in
detail in the table „ Delayed Start of
Programmes“. Use the programmes for
the following preparations:
8. Programme BAKING
Ấ Button - Time
ꢀ Notice:
For the after-baking of bread and cake.
The steps „dough kneading“ and
„dough rising“ fall away in this pro-
gramme.
• The programmes that can be started
with a time delay are listed in the
table „Temporal progress of the
program“.
1. Programme NORMAL
For white and mixed-flour bread. This
programme is the most frequently used.
Memory function
9. Programme MARMALADE
For making jams and preserves.
The programme is, with the switch-on
after electricity power cuts of less than
ca. 10 minutes duration, automatically
continued from the same position. This
memory function is intended for cases
of electricity power cuts.
2. Programme FAST
For the fast preparation of white and
mixed-flour bread.
• The programmes FAST, CAKE, EX-
PRESS, and MARMALADE cannot
be started with a time delay.
10. Programme LOOSE
For the preparation of light and airy bread.
3. Programme WHITE BREAD
For fast preparation of an especially loose
white bread.
For more information see chapter
„Timerfunction“.
Functions of the Bread Baking
Machine
ꢀ Notice: Pressing Button Start/Stop Ạ
ends the programme definitively.
After this button has been pressed,
the programme is discontinued.
ạ Button - Browning
4. Programme EXPRESS
With the button Browning ạ you can
adjust the desired level of browning:
LIGHT-MEDIUM-DARK.
This function cannot be activated with
the programmes 7. DOUGH, 9. JAM and
10. LOOSE.
For all recipes of Level 1 which are to
be baked in the programmes NORMAL,
WHITE BREAD, FAST or LOOSE. Dough
in the programme Express rises appreciably
less and the breads are therefore com-
pacter and less loose. A time preselect is
not possible. With this programme please
always use lukewarm fluids.
Signal tone function
The signal tone sounds
•
•
on pressing all programme buttons,
during the second kneading process
in the programmes NORMAL, WHOLE-
WHEAT, FAST, CAKE, WHITE BREAD
and LOOSE, to give notice that cere-
als, fruit, nuts or other ingredients
can now be added to the mixture,
on reaching the end of the programme
•
- 8 -
- 9 -
ꢀ
ꢀ
Safety Functions
Programme selection
Example
•
•
Place the dough back into the
baking mould ᕤ, replace the baking
mould in the appliance and close the
lid ᕢ.
Reinsert the plug into the wall socket.
The baking programme will be auto-
matically continued.
If the temperature in the appliance is
too high for a newly selected program-
me, after it has been used directly pre-
viously for another programme, on the
new start there appears in the display
ᕧ „H:HH“. The signal tone sounds. Should
such a case occur, press the button
Stop/Start Ạ until the detail „H:HH“ is
erased and the basic adjustments
appear in the display ᕧ. Wait for ca. 20
minutes, with the lid ᕢ open, until the
appliance has cooled down.
•
•
•
Choose the desired programme with
the button Selection ả.
Choose the desired browning with
the button Browning ạ.
To start the programme, press the
button Start/Stop Ạ.
A standard mixed-flour bread with
medium browning and a larger bread
weight is to be baked during a later period
of time. First of all select programme 1 ả,
medium browning ạ and the dough
volume Level II Ả (larger bread weight).
Let us assume it is 08:00 and the bread
should be ready in the evening at
around 18:30, i.e. in ten hours and 30
minutes time. Press the button Time Ấ
until 10:30 appears, as the time period
to be considered is one of ten hours and
30 minutes, between „now“ (8:00 Uhr)
and the desired time of completion.
With time delayed baking please do not
use perishable ingredients such as milk,
eggs, fruit, yoghurt, onions etc.!
Timerfunction
ꢀ Note: The interruption may not last
longer than 10 minutes! If it does,
the baking programme will not be
continued.
•
•
•
•
Choose the desired programme with
the button Selection ả.
Choose the desired browning with
the button Browning ạ.
With the button Time Ấ you can
delay the start of the programme.
Add to the time details already
given automatically in the respective
programme the period of time, in
hours and minutes, after which the
programme is to commence. If
necessary, take into consideration the
keep-warm time of one hour (on
completion of the baking process)!
Allowing the dough to rise
After the last kneading the Bread Baking
Machine creates the optimal temperature
for the dough to rise. Absolutely leave
the appliance lid ᕢ closed during this
period.
Baking bread
Inserting the ingredients
•
Place both of the kneading hooks
ᕥ onto the drive shaft.
•
To start the programme, press the
•
Place the ingredients into the baking
mould ᕤ. The ingredients must be
placed into the baking mould ᕤ in
the placement sequence specified in
the recipe. Ensure that no contami-
nation from outside can adhere to
the baking mould.
button Start/Stop Ạ.
Baking
ƽ Danger of Burns! Never open the
appliance lid ᕢ during the baking
process.
Mixing and kneading dough
The Bread Baking Machine mixes and
kneads the dough for as long as is sche-
duled in the baking programme (see Table).
The maximum time delay amounts to
13 hours.
The Bread Baking Machine automatically
regulates the baking temperature and
time. Should the bread still be too light
on completion of the baking programme,
it can be after-baked using the programme
BAKING:
ƽ Warning! Before you bake a particu-
lar type of bread with time delay
first try out the recipe under obser-
vation, to ensure that the rela-
tionships of the ingredients to each
other is correct, the dough is not too
firm or too thin, or the amounts are
not too large and could then possi-
bly overflow. Danger of Fire!
Tip: If you remove the kneading hooks
ᕥ from the dough after the last
kneading process, the bread will
not be torn when removing it from
the baking mould ᕤ. For this, you
must interrupt the baking program-
me.
Inserting the baking mould
•
Hold the non-stick coated baking
mould ᕤ firmly on the edges with
both hands and insert it exactly into
the middle of the baking space ᕩ
on the drive shaft.
•
Press the button Start/Stop Ạ until
the signal tone sounds and then
allow the appliance to cool down
for ca. 20 minutes, with the lid ᕢ
open.
Press the button Select ả several
times, to choose the programme
BAKING.
•
•
Carefully press the baking mould ᕤ
downwards until it engages.
Close the appliance lid ᕢ.
•
•
To interrupt the baking programme
remove the plug from the wall socket.
Do not press the button Start/Stop Ạ.
Open the appliance lid ᕢ and remove
the baking mould ᕤ.
•
•
Switching on
Insert the power plug into a correctly
•
To start the after-baking, press the
button Start/Stop Ạ.
installed power socket with a rating
of 230 V, ~50 Hz.
With floured hands, you can remove
the dough and then dismantle the
kneading hooks ᕥ.
- 10 -
- 11 -
ꢀ
ꢀ
•
When the desired browning has
been obtained, press the button
Start/Stop Ạ until a signal tone is
heard, the baking stops.
ƽ Warning
ƽ Attention
Due to moisture and vapours the surfaces
of various parts may undergo changes in
their appearance over a period of time.
This has no influence on the function
nor does it reduce the quality of the
baking results.
Always use oven cloths to remove the
baking mould ᕤ from the Bread Baking
Machine.
Before cutting the bread always check
to ensure that the kneading hooks ᕥ
have been removed from it.
ƽ Note
•
Place the baking mould ᕤ upside
down and, insofar as the bread does
not immediately fall onto the grill,
shift the knead drive back and forth
a few times from below until the
bread falls out.
Do not open the appliance lid ᕢ during
the baking process. The bread could
collapse.
Cleaning and Care
Before cleaning, remove the baking
mould ᕤ and the kneading hooks ᕥ
from the baking area. Wipe the exterior
surfaces of the baking mould ᕤ with a
moist cloth.
ƽ Warning
Before cleaning it, always remove the
power plug from the wall socket and
allow the appliance to cool down com-
pletely.
Tip: Check the consistency of the dough
after a kneading phase of 5 minutes.
It should have the consistency of a
soft, sticky mass. If it is too dry, add
some liquid to it. if it is too moist,
add some flour (1/2 to 1 teaspoon
one or more times, as needed).
Should one of the kneading hooks remain
stuck in the bread, use the supplied knead-
ing hook remover
Protect the appliance against splashing
water and moisture, these could cause
you to receive an electric shock.
ƽ Important
to dislodge it:
Never submerse the baking mould ᕤ
in water or other liquids.
•
•
•
Insert it into the round opening of
Clean the interior areas of the baking
mould ᕤ with warm soapy water.
Should the kneading hooks ᕥ be encrusted
and it is difficult to dissolve, fill the
baking mould ᕤ with hot water for
around 30 minutes.
Should the mountings in the kneading
hooks ᕥ be blocked, these can be care-
fully cleaned with a wooden toothpick
or similar.
the kneading hook ᕥ on the under-
side of the still warm bread and jam
the kneading hook remover
against the lower edge of the kne-
ading hook ᕥ.
Then carefully draw the kneading
hook ᕥ with the kneading hook
remover
this one can see at which position in
the bread the wing of the kneading
hook ᕥ is located.
Lightly cut the bread at this position
and then pull the kneading hook ᕥ
out.
Please observe the safety instructions
also.
Keeping warm
When the baking process is complete a
signal tone sounds several times to signify
that the bread or other food item can be
removed.In the display appears ᕧ „0:00“.
At the same time there begins a keep
warm period of one hour. Excluded are
the programmes EXPRESS, CAKE, DOUGH
and JAM.
ƽ Important
The appliance and its ancillaries are not
suitable for being cleaned in a dish
washing machine.
upwards. Whilst doing
Housing, lid, baking space
•
Remove all residual matter in the
baking space with a moist cloth or
a lightly moistened soft sponge.
Wipe also the housing and the lid,
again only with a moist cloth or
sponge. Ensure that the interior is
completely dry.
Do not use chemical cleaning agents or
solvents for cleaning the Bread Baking
Machine.
End of the programme
•
ƽ Warning
Before you open the appliance lid ᕢ,
remove the plug from the wall socket.
When not in use, always separate the
appliance from the power source!
Technical data
ƽ Note
Do not use any metal objects which may
cause scratches on the non-stick coating.
Rinse the baking mould ᕤ with warm
water directly after removing the bread.
This will help prevent the kneading
hooks ᕥ becoming stuck to the drive
shaft.
Model:
Bread Maker
KH 1170
Baking mould and kneading hooks
The surfaces of the baking mould ᕤ and
kneading hooks ᕥ have been given an
anti-stick coating. When cleaning them,
do not use corrosive detergents, abrasive
powders or objects that may cause scrat-
ches on the surface.
Power supply:
230V~50Hz
•
On completion of the programme
remove the baking mould ᕤ with
the help of an oven cloth.
Power consumption: 800 Watt
Allow the bread to cool for 15-30 minutes
before eating it.
- 12 -
- 13 -
ꢀ
ꢀ
Warranty & Service
Temporal progress of the programme
The warranty conditions and the
service address are contained in the
guarantee booklet.
Programm Nr.
1
2
3
4
5
6
7
8
9
10
Disposal
Under no circumstances should
you dispose of this appliance with
your domestic waste.
I
II
-
-
-
-
-
I
II
-
-
-
-
-
-
-
-
I
II
Bread size*
13 13
Std. Std.
13
Std.
13 13
Std. Std.
13 13
Std. Std.
13 13
Std. Std.
Clock timer (max.)
Degree of browning
Dispose of the appliance through an
approved disposal centre or at your
community waste facility.
Observe the currently applicable regula-
tions. In case of doubt, please contact
your waste disposal centre.
-
-
-
ꢁ ꢁ ꢁ ꢁ ꢁ ꢁ ꢁ ꢁ
ꢁ
Signal tone insert
ingredients
-
-
-
ꢁ ꢁ ꢁ ꢁ
ꢁ ꢁ ꢁ
ꢁ ꢁ
Total time hours. 3:20 3:30 1:58 3:50 1:52 3:30 3:40 2:00 1:50 1:00 1:20 3:09 3:20
All of the following time details in minutes
-
Pre-heating
Knead 1
17 20
12
5
22
3
37 40
22
11 22
12
Importer
-
-
15
19 15 10 12 12 10 15
KOMPERNASS GMBH
BURGSTRASSE 21
D-44867 BOCHUM
Signal tone (Inser-
tion of ingredients)
-
-
-
ꢁ ꢁ ꢁ ꢁ
ꢁ ꢁ ꢁ
ꢁ ꢁ
ca. ca.
2:46 2:46
Time details in the ca. ca. ca. ca. ca. ca. ca. ca. ca.
display
2:51 2:58 1:34 3:13 1:39 2:41 2:48 1:50 1:13
-
Knead 2
6
6
6
6
14
46
-
6
6
46
-
-
-
-
45
Allow dough to rise 1
Allow dough to rise 2
Allow dough to rise 3
Baking
46
19
45
46
26
46
19
35
8
7
19
45
22
-
25 50 27
39
-
55 62 55 65 65 55 62 96
60 20
56
Time details in the
display
0:00 0:00 0:00 0:00 0:00 0:00 0:00 0:00 0:00 0:00 0:00
0:00
60
-
-
-
-
Keeping warm
60
60 60
60
60
* Level I = 700 - 950 g
Level II = 950 -1250 g
- 14 -
- 15 -
ꢀ
ꢀ
• Remove the power plug immediately! Allow the appliance
to cool down, then remove the baking mould ᕤ.
Clean the exterior of the baking mould ᕤ as well as
the baking space ᕩ, as the smoke was probably caused
by food residues. Should there be no food residues in
the baking space ᕩ or on the exterior surfaces of the
baking mould ᕤ, do not switch the appliance back
on. Make contact with the customer service department.
What do I do if smoke comes from the baking space ᕩ
or the ventilation slots ᕨ?
Troubleshooting
What do I do if the kneading hooks ᕥ are stuck in the
baking mould ᕤ after baking?
• Fill the baking form ᕤ with hot water and twist the
kneading hooks ᕥ to loosen the encrustation under-
neath.
What happens if the finished bread is left inside the
bread maker?
• Through the „Keep-warm function“ it is ensured that
the bread is kept warm for ca. 1 hour and is also protected
against moisture. If the bread remains in the baking
machine for longer than 1 hour, it may become moist.
What has happened if the ingredients are not correctly
mixed or the bread is not correctly baked through?
• A false programme has been selected.
• The button Stop/Start Ạ has been pressed during
operation.
Is the baking mould ᕤ suitable for a dish washing
machine?
• No. Please rinse the baking mould ᕤand the kneading
hooks ᕥ by hand.
• During the baking process there was an extend power
failure.
• The appliance lid ᕢ was opened several times during
the baking process.
Why doesn't the dough get stirred, even if the motor is
running?
• Check to see if the kneading hooks ᕥ and the baking
mould ᕤ have correctly engaged.
• The kneading hooks ᕥ are blocked.
Remove the ingredients and do not re-use them. Remove
the baking mould ᕤ and check to see if the drive shaft
turns the kneading hooks. Should this not be so, make
contact with our customer service department.
What do I do if a kneading hook ᕥ is stuck in the
bread?
• Remove the kneading hook ᕥ with the kneading
hook remover
.
• The dough is too firm, that is why the kneading hooks
ᕥ block and the baking mould ᕤ is pressed
upwards. Put some fluids into the dough. Immediately
reclose the appliance lid ᕢ.
What happens if there is a power failure when a
Programme is running?
• With power failures of up to 10 minutes the Bread
Baking Machine carries through to the end the last
programme given to it .
What has happened if the baking mould ᕤ springs up
during the kneading process?
How long does it take to bake bread?
What size breads can I bake?
• Please take note of the exact times given in the table
„ Temporal progress of the programme“ (see page
15).
• The lateral springs on the base in the housing interior
have lost some of their tension. Remove the power
plug from the socket. Remove the baking mould ᕤ.
Press the springs outwards. Replace the baking mould
ᕤ and close the lid ᕢ. Re-insert the plug into the
power socket within 10 minutes. The programme will
be continued.
• You can bake the following bread sizes with the baking
mould ᕤ: - Level I Bread with a weight between
700-950 gr
- Level II Bread wih a weight between
950-1250 gr
Why can fresh milk not be used with time-delayed
baking?
• Fresh products such as milk or eggs spoil if they
remain in the appliance for too long.
The appliance crushes the added raisins.
• To avoid the breaking up of ingredients such as fruit
or nuts, add them to the dough after the signal has
sounded.
• The appliance is still too hot from the previous baking
process. Press the button Stop/Start Ạ until the basic
adjustments appear in the display ᕧ. Allow the appli-
ance to cool down for ca. 20 minutes, with the lid ᕢ
open. Afterwards, the appliance can be employed as
usual.
Why does the display ᕧ show „H:HH“ and the
appliance doesn't allow itself to be started?
- 16 -
- 17 -
ꢀ
ꢀ
- 18 -
ꢀ
|