Kodak Printer 1C9753 User Manual

Kodak 10/100 NIC Faceplate  
Kodak 10/100 NIC Quick ConÞguration  
Reference Guide  
Kodak  
10/100 NIC  
D1 D2  
NET  
LNK  
Applicable printers: Kodak XLS 8400PS, Kodak XLS 8600/8600PS, Kodak  
Professional 8657, Kodak Digital ScienceTM 8650/8650 PS color printers,  
Kodak Digital ScienceTM desktop color proofer 9000, and Kodak Digital  
ScienceTM DCP 9300 proofer  
Normal  
Mode Switches: D1 and D2 are operation mode switches; they are shown in  
Normal Operation Mode for printing (D1 & D2 Up).  
LEDs: The GREEN LNK connectivity LED should come ON  
when connected. The YELLOW NET Traffic LED should blink  
intermittently as it detects traffic on the network. Both LEDs  
should remain OFF if disconnected from the network.  
Ethernet Address: A unique NIC Ethernet address is assigned to each NIC  
(i.e. 0040C8 1234AB). The first six digits are always 00:40:C8. The last six  
digits are unique to each NIC.  
Network Broadcasts: The NIC uses its Ethernet address to advertise itself  
on Macintosh via Appletalk and on Windows via NetBeui as “KDxxxxxx”  
where “xxxxxx” are the last six digits of the address.  
Kodak 10/100 User Guide References:  
Ch1: Introduction/Config Overview Ch7: Windows NT 3.51  
NIC Operating Mode Switches  
Ch2: NIC Hardware Installation  
Ch3: Windows - FastManage  
Ch4: Novell Netware  
Ch8: Windows NT 4.0  
Ch9: Apple/Macintosh  
Ch10: Unix  
D1  
Up  
D2  
Up  
Mode  
Description  
Normal  
Default. Does not allow a telnet connection.  
Users can print to the unit.  
Ch5: Windows for Workgroups  
Ch6: Windows 95  
Ch11: Printing  
Up  
Down Telnet  
Allows a telnet connection to change its  
Ch12: Troubleshooting  
Diagnostic parameters. Users can also print.  
Down Down Reset to  
Defaults  
This setting is used to reset the NIC to use  
factory default configuration parameters.  
Refer to Appendix C in the User Guide for  
details.  
Appendices:  
A: Telnet Configuration Utilities  
B: 3rd Party Network Applications and Utilities  
C: Upgrading NIC Flash Firmware  
D: 10/100 NIC Specifications  
Down Up  
Test Page A parameter test page is generated when  
you power cycle the printer. Print jobs are  
not accepted. NOTE:The printer must be in  
PostScript mode. For raster-only printers,  
obtain the parameters via a Telnet session.  
E: Technical Assistance  
Kodak p rinter and NIC documentation and software are available on the  
Kodak Web site (www.kodak.com).  
Power cycle the printer whenever you change switch settings. When finished  
with configuration, return the switches to Normal mode, then power cycle the  
printer again for normal printing operation.  
Important: This 10/100 NIC is configured using remote, platform specific,  
configuration utilities ONLY. Configuration parameters entered via the printer  
front control panel and the corresponding printer front panel test print are not  
applicable to this 10/100 NIC.  
-4-  
Part Number 1C9753  
 

Indesit Washer PWE 91672 W User Manual
Intel Switch SIU520 SS7 User Manual
JL Audio Car Speaker 94460 User Manual
John Deere Ultrasonic Jewelry Cleaner T550 User Manual
JVC DVR HM DH40000U User Manual
Karcher Pressure Washer K 1800 IB User Manual
Kenwood Car Speaker KFC HQW308 User Manual
Kenwood Marine Radio TS 570DG User Manual
Keys Fitness Elliptical Trainer ST 45 User Manual
Korg Musical Instrument BX 3 User Manual