Kenyon Ventilation Hood B81200 Series User Manual

SIROCCO VENTILATION HOOD  
OWNER’S GUIDE  
READ AND SAVE THESE INSTRUCTIONS  
Models: B81200 Series  
 
FORRESIDENTIALUSEONLY  
NOT TO BE INSTALLED OVER GAS GRILLS  
Installation  
PLEASEREADENTIREINSTRUCTIONSBEFOREPROCEEDING.  
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.  
IMPORTANT: Save these Instructions for the Local Electrical Inspectors use.  
INSTALLER: Please leave these Instructions with this unit for the owner.  
OWNER:Pleaseretaintheseinstructionsforfuturereference.  
SAFETY WARNING: Turn off power circuit at the service entrance and lock out panel, before wiring this appliance.  
REQUIREMENT: 120 V AC, 60 Hz. 15 or 20 Amp  
Before Installing Hood  
Dimensions  
1. This hood is designed to be mounted flush to the rear wall (to  
Cabinet Front View  
avoid clearance from wall to hood) and to the internal sides of  
cabinet (where hood must be fixed); for this reason we  
suggest installing this hood only inside a cabinet having an  
internalwidthof221/16forthe24Model,287/16forthe30Model,347/16forthe  
9
15  
/
"
16  
36Modelandwithaninternaldepthofminimum71/2.Seefigure1.  
The external depth of the cabinet must be minimum 10 13/16and  
maximum 13 3/16. See figure 1.  
Fixing  
Point 1  
Fixing  
Point 1  
Fixing  
Point 2  
Fixing  
Point 2  
Attention! Do not consider the door of the cabinet when  
measuring.  
The appliance is also supplied with 4 spacers that can be  
snapped at fixing point 1 and 2 , cabinets /4wider can be  
24- 30- 36”  
1
used, see figure 2.  
2. For the most efficient air flow exhaust, use a straight run or as few  
elbows as possible.  
Cabinet Top View  
Internal Width  
1
22  
28  
34  
/
/
/
" (24" Model)**  
16  
" (30" Model)**  
16  
" (36" Model)**  
16  
7
7
CAUTION: Vent unit to outside of building ONLY.  
3
1
/
"
4
3. Ifallowedinyourarea,usemetallicflexductingonlytoconnectrigid  
duct directly to transitions.  
Rearside of the Cabinet/Hood  
13  
2
/ "  
16  
3
4. COLDWEATHERinstallationsshouldhaveanadditionalbackdraft  
damperinstalledtominimizebackwardcoldairflowandanonmetallic  
thermal break to minimize conduction of outside temperatures as  
part of the ductwork. The damper should be on the cold air side of  
the thermal break. The break should be as close as possible to  
where the ducting enters the heated portion of the house.  
Anon-returnsmokedamperissuppliedmountedonthetransition.  
5. Hood installation height above cooktop is at the users preference.  
The lower the hood above the cooktop, the more efficient the  
capturingofcookingodors,greaseandsmoke.Werecommendthat  
the hood be installed 18to 36over an electric cooktop and 25to  
36over a gas cooktop . Be sure that your hood model fits your  
installation.  
max 13  
min 10  
/
" *  
16  
/
13  
" *  
16  
Cut-Out for  
5" Duct  
C
Cabinet  
Door  
7
L
3
/ "  
16  
Cut-Out for  
1/2" Conduit  
* Do not consider the door of the cabinet  
** Use spacers for 1/4" wider cabinet  
Cabinet Right/Left Side View  
min Depth of  
Recessed  
1
Area =  
7
/
"
2
Cabinet  
Door  
min Height  
of Recessed  
3
Fixing  
Basic Installation Steps  
Foreasiestinstallation,thehoodshouldbeinstalledinthecabinet  
beforemountingthecabinettothewall.Inanycasetheinstallation  
stepsdonotchange.  
Point 1  
Area = 15  
/
"
16  
6"  
Fixing  
Point 2  
3
1
3
/
"
8
5
/
16  
"
1
4
/ "  
16  
11  
/
16  
"
Tools required for installation  
Screw driver (philips # 1 )  
Electric drill  
13  
13  
/
"
10  
/ "  
16  
16  
11  
17  
/
"
16  
Figure 1  
5
7
with twist bit /64and /32or 15/64”  
Tape  
Pin Housing  
This Hood can easily be installed following these basic steps:  
Prepare the cabinet (cut out bottom and top of the cabinet as  
required and mark fixing points)  
Run conduit and duct sections to the hood and make connections  
Fix the hood to the cabinet  
Motor Housing  
Fixing Points 1-2  
Spacer Pin  
Spacer  
for 1/4”  
wider  
Snap Spacer  
Pins Into Their  
Housings  
cabinet  
Mount the cabinet on the wall  
Connectducttotheoutsideandconduit section totheservicepanel  
Figure 2  
3
 
Installation  
Prepare the cabinet for installation  
1
7
7
22  
28  
34  
/
16  
/
16  
/
16  
" (24" Model)**  
" (30" Model)**  
" (36" Model)**  
Mark and cut-out the cabinet bottom as shown in figure 3.  
Fit the template, which comes with the hood, on the inner  
right side of the cabinet making sure the side with arrows  
matcheswiththeloweredgeofthecabinetandtherearedge  
of the cabinet or cut-out.  
Rearside of the Cabinet***  
3
max 13  
min 10  
/
" *  
1
16  
/
7
/ "  
2
CUT-OUT  
13  
" *  
16  
Cabinet  
Door  
C
L
* Do not consider the Door of the Cabinet  
4
** Add  
/
"
16  
when using Spacers  
*** Rearside of the Cut-Out for cabinet deeper  
3
than 13  
/
" (without considering the door)  
16  
Figure 3  
Drill 2holes5/64(seefigure4-fixingpoint1and2)and1blind  
Cabinet  
Door  
13  
hole 15/64in diameter, /64in depth.  
Move template to the other side and repeat.  
Make cut-out for duct and conduit, see figure 1.  
Fixing  
point 1-2  
Fixing  
point 1-2  
Template  
Template  
cutout for  
1/2" Conduit  
and 5" Duct  
Bottom of  
the cabinet  
Backside  
border  
Backside of  
the cabinet  
Blind hole  
(Side Springs  
Housing)  
Figure 4  
Prepare the hood for installation  
Remove the hood from packaging, check its condition and  
make sure the following pieces are included:  
1 hood,  
1 registration card  
1 instruction manual  
1 template  
1 transition with damper  
1 plastic bag with 4 hood fixing screws + 1 transition fixing  
screw and 4 spacers.  
Remove the light shield, unscrew and remove lamps to  
prevent damage when installing (see paragraph on Light  
replacementfordetails).  
Figure 5  
Pulloutthesliderandremovethegreasefilters(seeparagraph  
Toremovethegreasefiltersfordetails).  
Fit the transition on the outlet hole of the hood:  
This has a bayonet lock and must be fixed to the hood with  
one screw (Figure 5), check the opening and closing of the  
dampermountedinside.  
4
 
Installation  
Install the Hood  
Set the motor housing into the opening.  
Pushthespringinsidethemotorhousingusingascrewdriver  
as a lever from the inside of the motor housing.  
Insertitcompletelyinplacetakingcaretosnapsidessprings  
intotheblindholesmadefortemporaryfixingandthatconduit  
and duct section, if already fitted, run freely across the cut-  
outs on top of the cabinet, see figure 6.  
Cabinet  
Fixthehoodpermanentlywithtwoscrews(4.5x16)perside  
tobeinsertedfrometheinsideofthehoodtothecorresponding  
sidefixingpoints1and2drilledonthecabinet, seefigure7.  
Connect a 5duct to the transition and seal with tape.  
Connect to power supply  
Side Spring  
Attention! While mounting the hood on the wall cabinet be  
sure once the hood has been fastened, that the wiring  
compartment is easily and safely accessible, in order to  
make safety inspections and/or maintenance operations.  
WARNING!  
ELECTRICALGROUNDINGINSTRUCTIONS  
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL  
JUNCTION BOX WITH 3 WIRES, ONE OF WHICH  
(GREEN/YELLOW) SERVES TO GROUND THE  
APPLIANCE. TOPROTECTYOUAGAINSTELECTRIC  
SHOCK, THE GREEN/YELLOW WIRE MUST BE  
CONNECTED TO THE GROUNDING WIRE IN YOUR  
HOME ELECTRICAL SYSTEM, AND IT MUST UNDER  
NOCIRCUMSTANCESBECUTORREMOVED.  
ing  
Side Spr  
Figure 6  
Warning:Turnoffpowercircuitattheservicepanelbeforewiring  
this unit.  
Cabinet  
Door  
120 VAC, 15 or 20 Amp circuit required.  
a. Remove j-box cover as shown in Figure 8.  
Fixing  
point 1-2  
b. Removetheknockoutandinstallthestrainrelief(conduit)  
Fixing  
point 1-2  
connector (1/2") in junction box.  
Template  
Template  
cutout for  
1/2" Conduit  
and 5" Duct  
c. Run 3 wires; black, white and green (#16 AWG) in 1/2"  
conduit from service panel to junction box.  
Bottom of  
the cabinet  
Backside  
border  
d. Connect black wire from service panel to black or red in  
junctionbox,whitetowhiteandgreentogreen-yellow.See  
Figure8.  
Backside of  
the cabinet  
Blind hole  
(Side Springs  
Housing)  
Figure 7  
e. Close junction box cover.  
Conduit  
Figure 8  
5
 
Box adjustment  
M
Thehoodcanbeinstalledincabinetswithdifferentdepths(see  
alsofigure1fordetails);howeverthefrontofthesliderboxmust  
always be flush with the front of the cabinet.  
For alignment, adjust the back stops of the box.  
For box adjustment, loosen screws M, slide the square plates  
P as necessary, and tighten screws M (Figure 8).  
Ensure that the drawer, when fully retracted, turns OFF all  
P
power by acting positively on the rear microswitch.  
Figure 8  
Final installation steps  
Insert lamps in place.  
Fit the Lamp Shield.  
Fit the Grease Filters.  
Check all light bulbs to make sure they are secure in their  
sockets,thenturnpoweroninservicepanelandchecklights  
andbloweroperationperUse&Caresectionofthismanual  
and install filters.  
Make sure to leave this manual for the home owner.  
6
 
READTHEINSTRUCTIONSCAREFULLYBEFOREUSINGTHERANGEHOOD.  
For satisfactory use of your hood, become familiar with the various functions  
of the hood as described below  
Use and Care  
Control Pad Functions  
Air outlet  
Motor  
Housing  
Light OFF  
Light ON  
0
1
2
3
4
0
1
Slider  
Box  
Very High Speed  
Right Grease  
Filter  
Handles  
High Speed  
Medium Speed  
Low Speed  
Blower OFF  
Left Grease Filter  
Handles  
Grease  
Filters  
Lamp Shield  
Figure 7  
Operating Instructions  
The blower should be turned on for about 5 minutes before cooking in order to establish air currents upward through  
the hood.  
Use the low speeds for normal use and the higher speeds for strong odors or fumes.  
Minimize cross drafts which will reduce the effectiveness of the hood.  
7
 
HoodCleaning  
Be sure lights are cool before cleaning the hood.  
To Clean Filters  
The metal grease filters will last forever.  
They are made of anodized aluminum  
It is recommended that the filters be washed at least once a month; they  
can be washed by hand or in the dishwasher.  
Drain water through edge holes and let each filter dry thoroughly before  
replacing it.  
To Remove The Metal Grease Filters  
Turn blower and lights off.  
Pushsimultaneouslythetwogreasefilterhandlesfirstupwards,then pulltowards  
the center and extract the filters Figure 8.  
Figure 8  
Toreinstall,reverseprocedure.  
To Clean Hood Surface  
For general care, wipe the outside of the white or black hood with sudsy water  
orgeneralkitchenhouseholdcleaners, rinsewellanddrywithcleansoftclothto  
avoidwatermarks.  
Do not use abrasive products.  
Lights replacement  
R
Q
NOTE: Turn blower and lights off. Make sure the lights are cool. If new lights  
G
do not operate be sure lights are inserted correctly before calling service.  
Remove the light shield Q by pushing simultaneously the two unlocking buttons  
R (Figure 9); for safety reasons make sure to remove the light shield from its  
suspension slides G.  
Attention: When removing, handle the light shield by the glass.  
Pull out fluorescent tube and replace with Philips Type PL-S 9 Watt maximum.  
Refit the light shield.  
Figure 9  
8
 
9
 
10  
 
11  
 
LI1QVB Ed. 05/02  
 

Insignia MP3 Player NS DA2G User Manual
IOGear Switch GCS932U User Manual
Jackson Dishwasher 300X User Manual
Jensen Marine Radio MSR170 User Manual
JVC Car Stereo System GET0564 001A User Manual
JVC VCR SR 9090U User Manual
Jwin CD Player JX CD483 User Manual
Kenmore Gas Grill 41516218 User Manual
KitchenAid Freezer 4KSRF36DT User Manual
KitchenAid Speaker 8301169 User Manual