DPX504U
DPX404U
DPX304
DUAL DIN SIZED CD RECEIVER
INSTRUCTION MANUAL
Before reading this manual, click the button below to check the latest edition and the
modified pages.
Check the latest edition
© 2010 Kenwood Corporation All Rights Reserved.
IM328_Ref_E_en_01
DSP Setup
54
Car Type Selection
Speaker Setting
Car Type Fine Adjustments
X’Over Setting
Audio Preset Memory
Audio Preset Recall
Log Function
Log Function recall
Log Function item lock
Deleting a Log Function item
Log Function category setting
Tuner Log Function time setting
58
62
Bluetooth Setup
Bluetooth Setting
Registering Bluetooth device
Registering PIN Code
Selecting the Bluetooth device You Wish to
Connect
Deleting a Registered Bluetooth device
Downloading the Phone Book
Adding a Voice Dialing Command
Setting a Voice Command for Category
SMS (Short Message Service)
70
Downloading the SMS
SMS (Short Message Service)
Appendix
72
74
78
Troubleshooting Guide
Specifications
English
|
3
Before use
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
Demonstration mode. Refer to <Demonstration mode
About discs used with this unit
• This unit can only play the CDs with
• The following discs cannot be used:
- Discs that are not round
- Discs with coloring on the recording surface or
discs that are dirty
- Recordable/Rewritable disc that has not been
finalized (For the finalization process, refer to
your disc writing software, and your disc recorder
instruction manual.)
- 8 cm (3 inch) disc (Attempt to insert using an
adapter can cause malfunction.)
.
2WARNING
To prevent injury or fire, take the following
precautions:
• Stop the car before operating the unit.
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Handling discs
¤
CAUTION
• Do not touch the recording surface of the disc.
• Adjust the volume so that you can hear sounds
outside the car. Driving with the volume too high
may cause an accident.
• Wipe off the dirt on the panel with a dry silicon or
soft cloth.
• Do not stick tape etc. on the disc, or use a disc with
tape stuck on it.
• Do not use any accessories for the disc.
• Do not use any solvents to clean discs. Use a dry
silicon or soft cloth.
• Clean from the center of the disc and move
outward.
Failure to observe this precaution may result in
damage to the monitor or unit.
• When removing discs from this unit, pull them out
horizontally.
• Remove the rims from the center hole and disc
edge before inserting a disc.
Condensation
When the car is air-conditioned, moisture may collect
on the laser lens. This may cause disc read errors. In
this case, remove the disc and wait for the moisture
to evaporate.
How to reset your unit
Notes
If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when the
Reset button is pressed.
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• Characters that conform to ISO 8859-1 can be
displayed.
• Characters that conform to ISO 8859-5 or ISO 8859-1
can be displayed. Refer to “Russian”/ “RUSSIAN SET”
• The Radio Data System feature won’t work where
the service is not supported by any broadcasting
station.
Reset button
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
|
4
DPX504U/ DPX404U/ DPX304
English
|
5
Component names and functions
2
1
3
t
r
e
4
5
q p
8
7 6
w
9
1 Disc slot
p
DPX504U DPX404U
When inserted a disc (label side up), the source is
switched automatically and a song starts playing.
2 [0] button
[iPod] button
Select the iPod source.
DPX304
To eject the disc.
[38] button
To start or interrupt playback for CD and Audio
file.
3 [1] – [6] button
To recall the memorized station.
Switches the play mode between music discs,
Audio files, and iPod.
Mute the volume. (During Tuner, AUX source)
q [
4] / [¢] button
4 [DISP] button
To select a station, song and setting items.
To change the display mode.
w [BAND] button
5 [ATT] button
Turning the volume down quickly.
6 [ ] button
To select the receiving band, and the folder for
Audio file.
e [SRC] button
To enter the music search mode.
To enter the PTY mode.
To turn on and off the Traffic information mode.
(press the button at least 1 second)
7 [ ] button
To turn on this unit and select the Source.
To turn off this unit (press the button at least 1
second).
r Auxiliary Input Terminal
Portable audio device can be connected with the
mini-plug (3.5 mm ø).
To return to previous item.
• Use the mini-plug cable which is stereo type and does
not have any resistance.
8 [VOL] knob
To adjust volume.
t
DPX504U DPX404U
Enters function setting mode and setting item
(turn and press the knob). Refer to <Function
setting Operation> (page 9) for details.
USB Terminal
When connecting, open up the USB terminal lid. A
USB device or an iPod can be connected.
9
DPX504U
[LOG] button
To display a Log Function list.
DPX404U DPX304
[B.BOOST] button
To boost the bass tone in two steps (LV1, LV2,
OFF).
|
6
DPX504U/ DPX404U/ DPX304
English
|
7
General operation
Common Operation
Power and source select
Turns the power ON by pressing the [SRC]
button.
SRC
When the power is ON, select a source.
Press the [SRC] button each time switches
between sources.
Tuner (“TUNER”) ➜ USB (“USB”) or iPod (“iPod”)
(DPX504U/ DPX404U only) ➜ CD (“CD”) ➜
Auxiliary input (“AUX”) ➜ Standby (“STDBY”/
“STANDBY”) ➜ Tuner...
DPX504U
VOL
iDPPoX4d04U
Before Using
Canceling the Demonstration Mode
Cancel the demonstration mode when you use it for
the first time after installation.
DPX504U DPX404U
Press the [iPod] button to switch the source to
iPod.
1
2
Press the [VOL] knob to cancel the demonstration
mode when the messages “To cancel DEMO
press the volume knob”/ “CANCEL DEMO PRESS
VOLUME KNOB” are displayed (approx. 15
seconds).
Press the [SRC] button for at least 1 second to
turns the power OFF.
⁄
Settings> (page 44). (DPX504U only)
• When an optional accessory is connected, the source name
for each device appears. (DPX504U only)
• When connection of the iPod is recognized, the source
display changes from “USB” to “iPod”.
• This unit automatically turns full power OFF after 20
minutes lapses in Standby mode in order to save the
vehicle’s battery. The time until full power OFF can be set in
Turn the [VOL] knob to select “YES” and press the
[VOL] knob.
⁄
• Demonstration mode can also be cancelled in “DEMO
Mode” of Function setting mode. Refer to <Demonstration
Volume
Turning the [VOL] knob adjusts the sound
volume.
|
8
DPX504U/ DPX404U/ DPX304
Function setting Operation
The basic operating procedure for using this
function is described below. The individual function
items are covered in the operating procedures.
1
Select the source
Press the [SRC] button.
Function items vary from source to source.
2
3
Enter Function setting mode
Press the [VOL] knob.
Select the setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
Repeat the operation until your desired setup item
is selected.
Operation example:
4
3
1[VOL]
3[
]
2
Settings
Exit
Seek Mode
1
1
[VOL]
[
]
2
4
Auto Memory
Audio Control
1 sec.
In this manual, the above selection is indicated as
Select “Settings”/ “SETTINGS” >“Seek Mode”/
“SEEK MODE”.
4
5
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
Exit Function setting mode
Press the [ ] button for at least 1 second.
English
|
9
Function of DPX504U/ DPX404U
iPod/iPhone Operation
Selecting a song by browsing iPod
Searching for the song you want to play.
1 – 6
1
2
3
Select iPod source
Press the [iPod] button.
SRC
Enter Music search mode
Press the [ ] button.
4 ¢
iPod
VOL
Select a song
Operation type
Move between items
Select an item
Skip Search
Return to previous item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [4] or [¢] button.
Press the [ ] button.
Basic Operation
Playing iPod
✍ For example: Searching by Artist name.
Turn the [VOL] knob and press it when the
desired item is displayed.
• Connect an iPod
When connected, the source is switched
automatically and a song starts playing.
Select “Artists”/ “ARTISTS” > Artist name > Album
name > Song title
• Select iPod source
Press the [iPod] button.
Cancelling Enter Music search mode
Press the [ ] button for at least 1 second.
⁄
• KCA-iP101/iP102 (optional accessory) is recommended to
connect an iPod.
⁄
• Characters which cannot be displayed are left blank. If non
of the characters can be displayed, the browse item name
and digits are displayed.
Song Select
Press the [4] or [¢] button.
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
Items
Playlists
Artists
Albums
Songs
Display
“PLIST***” Podcasts
“ART***”
“ALB***”
“PRGM***”
Items
Display
“PDCT***”
“GEN***”
“COM***”
Genres
Composers
Pause and Play
Press the [6] button to pause or resume
playback.
•
Remove iPod
1
Select a source other than the iPod
Press the [SRC] button.
2
Remove the iPod.
⁄
• Removing the iPod with it selected as a source can damage
the data stored in the iPod.
|
10 DPX504U/ DPX404U/ DPX304
Play function
iPod Control by Hand Mode
Allowing you to operate iPod with the control on
the iPod.
Press the [iPod] button for at least 1 second.
When the iPod control by hand mode is selected,
“iPod by Hand Mode”/”HANDS ON” is displayed.
Repeat play
Press the [4] button.
Switches between Repeat (“File Repeat ON”/ “FILE
REPEAT”) and off (“File Repeat OFF”/ “REPEAT OFF”)
when pressed.
⁄
Random play
• In the iPod Control by hand mode, iPod cannot be operated
using this unit.
• This mode is not compatible with music information
display. The display will show “iPod by Hand Mode”/ “iPod
MODE”.
Press the [3] button.
Randomly plays the music.
Pressing the button toggles the setting between
Random play on (“Folder Random ON”/ “FOLDER
RANDOM”) and off (“Folder Random OFF”/
“RANDOM OFF”).
• iPod can be operated when it conforms to the iPod control
function.
Press this button again cancels the Random play.
All Random play
Press the [3] button for at least 1 second.
All songs in iPod are played at random.
Pressing the button toggles the setting between All
random play on (“All Random ON”/ “ALL RANDOM”)
and off (“All Random OFF”/ “RANDOM OFF”).
Press this button again cancels the All Random
play.
⁄
• The time required to turn on the all random function may
become longer depending on the number of songs in iPod.
• Turning on the all random function changes the iPod
browse item to “Songs”. This browse item will not be
changed even if the all random function is turned off.
• If the browse item is changed to search for music while the
all random function is on, the all random function is turned
off and the songs in the browse item are played at random.
English
|
11
Function of DPX504U/ DPX404U
iPod/iPhone Operation
iPod Setting
Selecting the Search mode
You can select the following iPod Setting items.
You can select the most suited search method for
the desired song from 4 types of the Search mode.
1
Select iPod source
Press the [iPod] button.
Search mode Operation Overview
“Related Search”/ Press the [1] Searches for music of the same artist
2
3
Enter Function setting mode
Press the [VOL] knob.
“RELATED SRCH” button.
or genre as the one being played.
Refer to the <Related Search>
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”/ “SETTINGS”.
“Direct Search” Press the [2] You can quickly search the desired
button.
song by specifying its Search item
(artist, album, etc.) and initial.
Function of DPX504U.
4
Select the setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
“Alphabet
Search”/
“ALPHABET
SRCH”
Press the [3] You can select an alphabetic character
button.
from the list in the Search item (artist,
album, etc.) selected now.
Display
Overview
“Settings”/
“SETTINGS”
“Register My
Press the [5] Registers a song to My Playlist.
Playlist”/“Recall button.
My Playlist”/
“MY PLAYLIST”
“0.5%”/ “1%”/ “5%”/ “10%”
“Delete My
Deletes the registered My Playlist.
1
2
3
Select iPod source
Press the [iPod] button.
DELETE”
(page 14) for the operation.
(
: Factory setting)
Enter Music search mode
Press the [ ] button.
5
6
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
Select the Search mode
Press the [1]/ [2]/ [3]/ [5] button.
Exit Function setting mode
Press the [ ] button for at least 1 second.
Cancelling Music search mode
Press the [ ] button for at least 1 second.
⁄
Changing the setting of one reflects the other.
|
12 DPX504U/ DPX404U/ DPX304
Function of DPX504U
Related Search
Direct Search
Searches for music of the same artist or genre as the
one being played.
You can quickly search the desired song by
specifying its Search item (artist, album, etc.) and
initial.
1
2
3
4
Select iPod source
Press the [iPod] button.
1
2
3
4
Select iPod source
Press the [iPod] button.
Enter Music search mode
Press the [ ] button.
Enter Music search mode
Press the [ ] button.
Enter Related search mode
Press the [1] button.
Enter Direct Search mode
Press the [2] button.
Select the Search item
Turn the [VOL] knob and press it when the
desired Search item is selected.
Select the Search item
Turn the [VOL] knob and press it when the
Display
Searches music
desired Search item is selected.
“Search Artist”/
“SRCH ARTIST”
Displays the album of the same artist.
Display
“PLAY LIST”
“ARTIST”
“ALBUM”
“SONG”
Items
Playlists
Artists
Albums
Songs
Display
“PODCAST”
“GENRE”
Items
Podcasts
Genres
“Search Album”/ Displays music in the album in which the one
“SRCH ALBUM”
“Search Genre”/
“SRCH GENRE”
being played is included.
Displays the artist of the same genre.
“COMPOSER”
Composers
“Search Composer”/ Displays the album including music created by the
“SRCH COMPOSER” same Composer.
5
6
Select the character to be searched for
After this step, you need to browse. See step 3 of
select a song.
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [4] or [¢] button.
Move to the next column
Cancelling the Related search
Press the [ ] button for at least 1 second.
Up to 3 characters can be entered.
⁄
Determine the selected initial
Turn the [VOL] knob and press it when the
desired item is displayed.
• Related search cannot be performed while playing the
Podcast.
• When the music being played has no information on
browsing items or no music was found, “Not Found”/ “NOT
FOUND” is displayed.
Select “DONE”.
Start search. When search is completed, the music
search mode is selected again at the selected
character position.
After this step, you need to browse. See step 4 of
select a song.
Cancelling the Direct Search
Press the [ ] button for at least 1 second.
⁄
• Characters that can be entered are alphabetical characters
(A to Z), numerical characters(0 to 9), and “ * ”.
• “ * ” indicates characters other than alphabetical and
numerical characters. You cannot enter any more characters
when entering “ * ” in the first character position.
• If the first character string begins with an article “a”, “an”, or
“the” in the Direct Search mode, it is searched for in defiance
of the article.
English
|
13
Function of DPX504U/ DPX404U
iPod/iPhone Operation
Alphabet Search
My Playlist
You can select a song by alphabet. This function
searches songs whose name contain the specified
character(s) in the list of the selected Search item
(artist, album, etc).
Allows you to register your favorite songs in the
Playlist of this unit. You can register up to 10 songs
in the Playlist.
Registering Songs in the Playlist
1
2
3
Select iPod source
Press the [iPod] button.
1
2
Play the song you want to register
Register the song
Enter Music search mode
Press the [ ] button.
Press the [5] button for at least 2 second.
“## Stored”/ “## STORED” (Registration number) is
displayed.
Select search item
Turn the [VOL] knob and press it when the
desired item is displayed.
Select the item (artist, album, etc.) you want to
search.
⁄
• Make a Playlist from the songs stored in one iPod. If you
attempt to register a song stored in a different iPod, ”No
Information”/ “NO INFO” appears and then ”Delete My
Playlist All Delete?”/ “MPLIST DELETE” appears. Select “YES” to
delete the Playlist when you want to remake it.
• If you attempt to register the eleventh song, ”Memory
Full”/ ”MEMORY FULL” appears and you cannot register it
accordingly. To register the song, delete an unnecessary
song.
4
5
Enter Alphabet Search mode
Press the [3] button.
Search for song
DPX504U
Operation type
Select the character
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
• Do not register Podcasts. Songs you do not want to register
may be registered, or playback may not be carried out
correctly.
DPX404U
Playing the Song in the Playlist
Operation type
Select the character
Move the cursor to the
enter character position
Determine the selected
character
Operation
Turn the [VOL] knob.
Press the [4] or [¢] button.
1
Enter Playlist mode
Press the [5] button.
2
Play the song in the Playlist
Turn the [VOL] knob and press it when the
desired item is displayed.
Press the [VOL] knob.
Select the song you want to play.
Cancelling the Alphabet Search
Press the [ ] button for at least 1 second.
⁄
• Turning ACC OFF or the power OFF cancels the My Playlist
mode.
⁄
• The time of search by alphabet may become long
depending on the number of songs or items in iPod.
• If the first character string begins with an article “a”, “an”,
or “the” in the Alphabet Search mode, it is searched for in
defiance of the article.
• The ending of a song may be cut unless the song has a
silence of 1 second or longer at the end.
• Random play cannot be performed during playback of a
song in the Playlist.
Deleting a Song from the Playlist
1
2
3
Enter Playlist mode
Press the [5] button.
Enter Delete Playlist mode
Press the [VOL] knob for at least 1 second.
Select Delete Playlist mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select ”Delete One”/ “DELETE ONE” or ”Delete
All”/ “DELETE ALL”.
|
14 DPX504U/ DPX404U/ DPX304
4
Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
“Completed”/ “COMPLETED” is displayed.
Deleting the all song from the Playlist (In
Function setting mode)
1
Enter Function setting mode
Press the [VOL] knob.
2
Enter Delete Playlist mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”/ “SETTINGS” > “Delete My
Playlist”/ “MPLIST DELETE”.
3
Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
“Completed”/ “COMPLETED” is displayed.
⁄
• If you connect the different iPod from one registered to
My Playlist, “Delete One”/ “DELETE ONE” and “Delete All”/
“DELETE ALL” will not appear and all songs be deleted.
English
|
15
Function of DPX504U/ DPX404U
USB device Operation
File Search
Selecting the file you want to listen to from the
device being played now.
2 – 6
1
Select USB source
Press the [SRC] button.
SRC
Select the “USB” display.
2
3
Enter Music search mode
Press the [ ] button.
4 ¢
BAND
VOL
Select a file
Basic Operation
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Playing USB device
• Connect a USB device
When connected, the source is switched
Skip Search (Function of Music Press the [4] or [¢] button.
Editor media)
automatically and a song starts playing.
Return to previous item
Press the [ ] button.
✍ For example: Searching for ¡".
Turn the [VOL] knob and press it when the
desired item is displayed.
• Select USB source
Press the [SRC] button.
Select the “USB” display.
Select “Music” > 1 > 2 > ¡"
⁄
• CA-U1EX (optional accessory) is recommended to connect
1
2
a USB device.
¡"
¡!
¡#
Moving to the next folder
Press the [BAND] button.
Cancelling Music search mode
⁄
Press the [ ] button for at least 1 second.
• The Music Editor media does not allow you to select a
⁄
folder.
Song Select
Press the [4] or [¢] button.
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
⁄
• No sound is output while playing Audio file.
Pause and Play
Press the [6] button to pause or resume
playback.
Remove USB device
1
Select a source other than the USB
Press the [SRC] button.
2
Remove the USB device.
⁄
• Removing the USB device with it selected as a source can
damage the data stored in the USB device.
|
16 DPX504U/ DPX404U/ DPX304
Play function
USB Setting
You can select the following USB Setting items.
Scan play
Press the [2] button.
Successively plays the intro of the music in the
1
Select USB source
Press the [SRC] button.
folder.
Select the “USB” display.
When Scan Play is turned on, “File Scan ON”/ “FILE
SCAN” is displayed.
Pressing this button again plays songs in the
normal mode starting with the song being played
now.
2
3
Enter Function setting mode
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”/ “SETTINGS”.
Random play
Press the [3] button.
Randomly plays the music in the folder.
When Random Play is turned on, “Folder Random
ON”/ “FOLDER RANDOM” is displayed.
Press this button again cancels the Random play.
4
Select the setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
Display
Overview
“Settings”/
“SETTINGS”
Repeat play
Press the [4] button.
Switches between File Repeat (“File Repeat ON”/
“FILE REPEAT”), Folder Repeat (“Folder Repeat ON”/
“FOLDER REPEAT”), and OFF (“Folder Repeat OFF”/
“REPEAT OFF”) when pressed.
“0.5%”/ “1%”/ “5%”/ “10%”
(
: Factory setting)
5
6
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
⁄
• The Music Editor media does not allow you select folder
Exit Function setting mode
Press the [ ] button for at least 1 second.
repeat play.
⁄
Changing the setting of one reflects the other.
English
|
17
Music CD/ Audio file Operation
DPX304
38
Function of Internal CD source
0
Music Search
Selecting the music you want to listen to from the
disc being played now.
2 – 6
1
Select CD source
Press the [SRC] button.
Select the “CD” display.
SRC
2
3
Enter Music search mode
Press the [ ] button.
4 ¢
BAND
VOL
Search for music
Basic Operation
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [ ] button.
Disc play
• Insert a disc.
When inserted, the source is switched
Return to previous item
automatically and a song is starts playing.
When a CD is inserted, the “IN” indicator is ON.
Cancelling Function setting mode
Press the [ ] button for at least 1 second.
• Select CD source
Press the [SRC] button.
Select the “CD” display.
Disc ejection
Press the [0] button.
Moving to the next folder
Press the [BAND] button.
⁄
• This operation can be performed only for the Audio file.
Song Select
Press the [4] or [¢] button.
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
⁄
• No sound is output while playing Audio file.
Pause and Play
DPX504U DPX404U
Press the [6] button to pause or resume
playback.
DPX304
Press the [38] button to pause or resume
playback.
|
18 DPX504U/ DPX404U/ DPX304
Function of DPX504U
Play function
Basic Operation of Disc Changer
(Optional)
Scan play
Press the [2] button.
Successively plays the intro of the music in the disc
or folder.
Select CD changer source
Press the [SRC] button.
Select the “CD CH” display.
When Scan Play is turned on, “Track Scan ON”/
“TRACK SCAN”/ ”File Scan ON”/ ”FILE SCAN” is
displayed.
Pressing this button again plays songs in the
normal mode starting with the song being played
now.
Moving to the next disc
Press the [BAND] button.
Song Select
Press the [4] or [¢] button.
Random play
Fast Forwards or Fast Backwards
Press the [3] button.
Hold down the [4] or [¢] button.
Randomly plays the music in the disc or folder.
When Random Play is turned on, “Disc Random
ON”/ “DISC RANDOM”/ “Folder Random ON”/
“FOLDER RANDOM” is displayed.
Pause and Play
Press the [6] button to pause or resume
playback.
Playing the Current Song or Disc Repeatedly.
(Repeat play)
Press the [4] button.
Switches between Track Repeat play on (“Track
Repeat ON”), Disc Repeat play on (“Disc Repeat
ON”), and Repeat play off (“Repeat OFF”) when
pressed.
Press this button again cancels the Random play.
Repeat play
Press the [4] button.
Switches between Track Repeat (“Track Repeat ON”/
“TRACK REPEAT”) and OFF (“Track Repeat OFF”/
“REPEAT OFF”) when pressed while playing a CD.
Switches between File Repeat (“File Repeat ON”/
“FILE REPEAT”), Folder Repeat (“Folder Repeat ON”/
“FOLDER REPEAT”), and OFF (“Folder Repeat OFF”/
“REPEAT OFF”) when pressed while playing an
Audio file.
Randomly plays the music in the disc changer.
(Magazine random play)
Press the [5] button.
When Magazine random play is turned on,
“Magazine Random ON” is displayed.
Press this button again cancels the Magazine
random play.
English
|
19
Tuner Operation
Tuner Setting
You can select the following Tuner Setting items.
1 – 6
1
Select Tuner source
Press the [SRC] button.
Select the “TUNER” display.
SRC
2
3
Enter Function setting mode
Press the [VOL] knob.
4 ¢
BAND
VOL
Turn the [VOL] knob and press it when the desired
item is displayed.
Select “Settings”/ “SETTINGS”.
Basic Operation
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the desired
item is displayed.
Selecting Tuner source
Press the [SRC] button.
Select the “TUNER” display.
Display
Overview
“Settings”/
“SETTINGS”
“Local Seek”/
“LOCAL SEEK” searched in auto seek tuning.
“ON”/ “OFF”
Selecting the Receiving Band
Press the [BAND] button.
Pressing the button switches the receiving band
(FM1, FM2, FM3, AM).
Only stations whose reception is good are
“Seek Mode”/ Selects the tuning mode of the radio.
Selecting the Receiving station
Press the [4] or [¢] button.
✍ Details of the station selecting in operation are
“SEEK MODE”
“Auto1”/ “AUTO1”: Automatic search for a
station.
“Auto2”/ “AUTO2”: Search in order of the
stations in the Preset memory.
“Manual”/ “MANUAL”: Normal manual
tuning control.
Traffic information
“Auto Memory”/ Memorizes 6 stations with good reception
“AUTO MEMORY” automatically.
“Forced MONO”/ Reduces the noise when stereo broadcasts are
“FORCED MONO” received as monaural.
“ON”/ “OFF”
“News”/“NEWS” Turns ON/OFF the News Bulletin Automatic
Reception function and sets the news bulletin
interrupt disabled time.
Press the [ ] button for at least 1 second.
Turns ON or OFF the Traffic Information function.
When the function is set to ON, “TI” indicator is ON.
If traffic bulletin starts when the function is ON,
“Traffic INFO”/ “TRAFFIC INFO” is displayed and
traffic information is received.
✍ If the volume is adjusted during reception
of traffic information, the adjusted volume
is memorized automatically. The memorized
volume will be applied next time the Traffic
Information function is turned ON.
“OFF”/ “00MIN”/ “00M” – “90MIN”/ “90M”
“AF”
When station reception is poor, automatically
switches to the station that is broadcasting
the same program over the same Radio Data
System network. (AF: Alternative Frequency)
“ON”/ “OFF”
“Regional”/
“REGIONAL”
Sets whether to switch to the station only in
the specific region using the“AF”control.
“ON”/ “OFF”
“Auto TP Seek”/ When traffic information station reception is
“AUTO TP SEEK” poor, automatically searches for a station that
can be received better.
“ON”/ “OFF”
(
: Factory setting)
5
Make a setting
Turn the [VOL] knob.
|
20 DPX504U/ DPX404U/ DPX304
6
Exit Function setting mode
Press the [ ] button for at least 1 second.
Station Preset Memory
Putting a station in the memory.
Remarks
•
1
2
Select the frequency to put in the memory
Press the [4] or [¢] button.
News (News Bulletin with Timeout Setting)
Automatically receives news bulletin when it starts. Set the
time during which interrupt is to be disabled after start of
another news bulletin. Changing “News 00MIN”/ “NEWS
00M” to “News 90MIN”/ “NEWS 90M” turns this function ON.
If news bulletin starts when this function is ON, “News”/
“NEWS” is displayed and news is received. If “20MIN”/ “20M”
is has been set, reception of another news bulletin will not
start for 20 minutes. The news bulletin volume is the same
level that was set for Traffic Information.
Select the number to put in the memory
Press the [1] – [6] button for at least 2 seconds.
⁄
• Up to 6 stations with a different band (FM/AM) can be
memorized to the [1] – [6] button according to the setting
• Forced MONO
Strong electrical fields (such as from power lines) may
cause unstable sound quality when it is set to ON. In such
a situation, turn it OFF.
English
|
21
Tuner Operation
Auto Memory Entry
Preset Tuning
Putting stations with good reception in the memory
automatically.
Recalling the stations in the memory.
1
2
Select the radio band
1
2
3
Select the radio band you wish to store in the
preset memory
Recalls the memorized station
Press the [1] – [6] button.
Enter Function setting mode
Press the [VOL] knob.
Enter Auto Memory Entry mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”/ “SETTINGS” > “Auto
Memory”/ “AUTO MEMORY”.
4
Open Auto Memory Entry
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
When 6 stations that can be received are put in the
memory, auto memory entry closes.
|
22 DPX504U/ DPX404U/ DPX304
4
Exit PTY mode
Press the [ ] button.
PTY (Program Type)
Selecting the Program Type below and searching
for a station.
⁄
• When the selected Program Type is not found, “No PTY”/
“NO PTY” is displayed. Select another Program Type.
• The operation ends automatically if you do not operate
within 30 seconds.
DPX504U
Program Type Display
Speech
Music
News
Current Affairs
Information
Sport
Education
Drama
Culture
Science
Varied
Pop Music
Rock Music
Easy Listening
Music
Program Type Display
Serious Classical “Classics”
“Speech”
“Music”
“News”
“Affairs”
“Info”
Other Music
Weather
Finance
“Other M”
“Weather”
“Finance”
Children’s programs “Children”
“Sport”
Social Affairs
Religion
Phone In
“Social”
“Educate”
“Drama”
“Culture”
“Science”
“Varied”
“Pop M”
“Rock M”
“Easy M”
“Religion”
“Phone In”
“Travel”
Travel
Leisure
“Leisure”
“Jazz”
“Country”
“Nation M”
“Oldies”
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
“Folk M”
“Document”
Light Classical
“Light M”
DPX404U DPX304
Program Type Display
Program Type Display
Speech
Music
News
Current Affairs
Information
Sport
Education
Drama
Culture
Science
Varied
Pop Music
Rock Music
Easy Listening
Music
“SPEECH”
“MUSIC”
“NEWS”
“AFFAIRS”
“INFO”
Serious Classical “CLASSICS”
Other Music
Weather
Finance
“OTHER M”
“WEATHER”
“FINANCE”
Children’s programs “CHILDREN”
“SPORT”
Social Affairs
Religion
Phone In
“SOCIAL”
“EDUCATE”
“DRAMA”
“CULTURE”
“SCIENCE”
“VARIED”
“POP M”
“ROCK M”
“EASY M”
“RELIGION”
“PHONE IN”
“TRAVEL”
Travel
Leisure
“LEISURE”
“JAZZ”
“COUNTRY”
“NATION M”
“OLDIES”
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
“FOLK M”
“DOCUMENT”
Light Classical
“LIGHT M”
• Speech and Music include the Program type shown below.
Speech: Items in the white letters.
Music: Items in the black letters.
1
2
3
Enter PTY mode
Press the [ ] button.
Select the Program Type
Turn the [VOL] knob.
Search for the selected Program Type station
Press the [4] or [¢] button.
English
|
23
Tuner Operation
Program Type Preset
Changing Language for PTY Function
Putting the Program Type in the Preset button
memory and quick recall.
Selecting the Program Type display language as
follows.
DPX504U
Presetting the Program Type
Language
English
Spanish
French
Display
“English”
“Spanish”
“French”
“Dutch”
Language
Norwegian
Portuguese
Swedish
Display
1
Select the Program Type to preset
“Norwegian”
“Portuguese”
“Swedish”
“German”
2
Preset the Program Type
Press the desired [1] — [6] button for at least 2
seconds.
Dutch
German
DPX404U DPX304
Recalling the preset Program Type
Language
English
French
Display
“ENGLISH”
“FRENCH”
“GERMAN”
1
Enter PTY mode
Press the [ ] button.
German
2
Recall the Program Type
Press the desired [1] — [6] button.
1
2
3
Enter PTY mode
Press the [ ] button.
Enter Changing Language mode
Press the [ ] button.
Select the language
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a language.
|
24 DPX504U/ DPX404U/ DPX304
English
|
25
Function of DPX504U with KCA-BT200/BT300 (Optional Accessory)
Bluetooth Audio Operation
Basic Operation
Selecting Bluetooth Audio source
Press the [SRC] button.
Select the “BT Audio” display.
6
SRC
Pause and play
Press the [6] button.
4 ¢
Music Search
Press the [4] or [¢] button.
⁄
Connecting a Bluetooth Device
• All or some of the operations above cannot be performed if
the Bluetooth audio player is not ready for remote control.
• Switching between Bluetooth audio sources does not start
or stop playback automatically. Perform the operation for
starting or stopping playback.
• Some audio players cannot be controlled remotely or
reconnected after Bluetooth disconnection. Operate the
main unit of the audio player to connect Bluetooth.
Before use the Bluetooth device, you need to
connect Bluetooth device to this unit.
Pairing (Registering from Bluetooth devices)
To make your Bluetooth Audio player usable with
this unit, you need to register it (pairing).
1
Turn on this unit
Press the [SRC] button.
2
Start registering this unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
audio player (pairing). Select “KCA-BT200”/ “KCA-
BT300” from the list of connected units.
3
4
Enter a PIN code
Input the PIN code (“0000”) in the Bluetooth
device.
Check that registration is complete on the
Bluetooth device.
✍ PIN code is set to “0000” as the default. You can
change this code. Refer to <Registering PIN
By operating the Bluetooth device, start
Bluetooth connection.
⁄
• If pairing does not succeed, try followings.
– Turn off the power of this unit and turn it back on. And
then try the pairing operation again.
– If other audio players have been registered, delete them.
|
26 DPX504U/ DPX404U/ DPX304
English
|
27
Function of DPX504U with KCA-BT200/BT300 (Optional Accessory)
Operation of hands-free phoning
⁄
1 – 6
DISP
ATT
SRC
4 ¢
LOG VOL
Connecting a Bluetooth Device
Before use the Bluetooth device, you need to
connect Bluetooth device to this unit. The following
3 steps procedure is necessary.
Step 1. Pairing (Registering from Bluetooth
devices)
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing).
1
2
Turn on this unit
Press the [SRC] button.
Start registering a this unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
hands-free unit (pairing). Select “KCA-BT200”/ “KCA-
BT300” from the list of connected units.
3
Enter a PIN code
Input the PIN code (“0000”) in the Bluetooth
device.
Check that registration is complete on the
Bluetooth device.
✍ PIN code is set to “0000” as the default. You can
change this code. Refer to <Registering PIN
4
By operating the Bluetooth device, start hands-
free connection.
Step 2. Connection
If you have registered 2 or more cell-phones, you
need to select one of them. For more details,
When a cell-phone is connected, the “BT” indicator
is light up.
Step 3. Hands-free phoning
You can do hand-free phoning when the
connection is made.
|
28 DPX504U/ DPX404U/ DPX304
Receiving a Call
During a Call
Answering a Phone Call
Disconnecting a Call
Press the [VOL] knob.
Press the [SRC] button.
⁄
Switching to the Private Mode
Press the [6] button.
Switches between Private talk (“PRIVATE”) and
• The following operations disconnect the line:
- Insert a CD.
- Connect a USB device.
• The name of the calling party is displayed if it has already
been registered in the Phone Book.
Hands-free talk each time this button is pressed.
⁄
• Depending on the type of your cell-phone, switching
to the private talk mode may select the source that was
used before commencing the hands-free connection. If
this happens, the source cannot be switched back to the
hands-free talk mode by operating this unit. Operate your
cell-phone to return to the hands-free talk mode.
Rejecting an Incoming Call
Press the [SRC] button.
Adjusting the Voice Volume during a Call
Turn the [VOL] knob.
English
|
29
Function of DPX504U with KCA-BT200/BT300 (Optional Accessory)
Operation of hands-free phoning
Call Waiting
Other Functions
Answering Another Incoming Call with the
Current Call Suspended
Clearing the Disconnection Message
Press the [LOG] buttons for at least 1 second.
“HF Disconnect”/ “HF D-CON” disappears.
1
2
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “ANSWER”.
Answering another Incoming Call after
Terminating the Current Call
Press the [SRC] button.
Continuing the Current Call
1
2
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “REJECT”.
Answering the Waiting Call after Terminating
the Current Call
Press the [SRC] button.
Switching between the Current Call and Waiting
Call
Press the [VOL] knob.
Each pressing of this knob switches the calling
party.
|
30 DPX504U/ DPX404U/ DPX304
Making a Call
Speed Dialing (Preset Dial)
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
2
Select a dialing method
Turn the [VOL] knob and press it when the
2
Select the number you want to recall from the
memory
desired item is displayed.
Press the [1] – [6] button.
Display
Overview
3
Make a call
Press the [VOL] knob.
“Phonebook” Selecting the initial to be searched for the phone
book.
“Incoming Calls” Calling a number in the incoming call list.
“Outgoing Calls” Calling a number in the outgoing call list.
“Missed Calls” Calling a number in the missed calls list.
“Number Dial” Making a call by entering phone number.
⁄
• You need to register the preset dial number. Refer to
Operation method of each mode is described
below.
3
Exit the dialing method mode
Press the [LOG] button for at least 1 second.
English
|
31
Function of DPX504U with KCA-BT200/BT300 (Optional Accessory)
Operation of hands-free phoning
Calling a Number in the Phone Book
Calling a Number in the Call log
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
2
Select the Phone Book mode
Turn the [VOL] knob and press it when the
desired item is displayed.
2
Select the call log mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Phonebook”.
Select “Outgoing Calls” (outgoing call),
“Incoming Calls” (incoming call), or “Missed
Calls” (missed call).
3
4
Select the initial to be searched for
Operation type
Move to the next character. Turn the [VOL] knob.
Determine the selected initial. Press the [VOL] knob.
Operation
3
4
Select a name or phone number
Turn the [VOL] knob.
✍ Switching between Display Modes
Press the [DISP] button.
Select the name
Operation type
Select the Phone number.
Select the name.
Operation
Turn the [VOL] knob.
Make a call
Press the [VOL] knob.
Press the [
4] or [¢] button.
⁄
✍ Switching between Display Modes
Press the [DISP] button.
• The outgoing call list and the incoming call list, and the
missed call list are the lists of calls originated from and
received at this unit. They are not the ones stored in the
cell-phone memory.
5
Make a call
Press the [VOL] knob.
⁄
• During search, a non-accent character such as “u” is
searched for instead of an accent character such as “ü”.
|
32 DPX504U/ DPX404U/ DPX304
Dial a Number
Make a Voice Dialing Call
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
1
Enter voice recognition mode
Press the [ATT] button for at least 1 second.
2
Select the number dial mode
Turn the [VOL] knob and press it when the
desired item is displayed.
2
“PB Name?” is displayed.
When a beep is heard, say the name within 2
seconds.
Select “Number Dial”.
3
4
“PN Type?” is displayed.
When a beep is heard, say the category name
within 2 seconds.
3
Enter a phone number
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Press the [
Press the [
Make a call
Press the [VOL] knob.
✍ This step is the same as step 4 of the procedure
32). You can make a call or select a category.
¢
] button.
] button.
4
• Press the number ([1] – [0]), #([FM]), *([AM]), or
+([¢]) button on the remote controller.
✍ To erase the entered phone number digit
by digit:
⁄
• If your voice cannot be recognized, a message is displayed.
Pressing the [VOL] knob allows you to retry voice input.
• Both the name and category require registration of a voice
tag. Refer to <Setting a Voice Command for Category>
Press the [4] button on the remote
controller.
4
Make a call
• Press the [VOL] knob.
• Press the [DIRECT] button on the remote
controller.
• Audio sound is not output during voice recognition.
⁄
• You can input max 32 digits.
English
|
33
Function of DPX504U with KCA-BT200/BT300 (Optional Accessory)
Operation of hands-free phoning
Registering to the Preset Dial Number Display of Phone Number type
List
(category)
The category items in the Phone Book are displayed
as follows:
1
Select the phone number you wish to register
Select the phone number with reference to the
following:
Display
Information
“General”/“
”
General
“Home”/“
“Office”/“
“Mobile”/“
“Other”/“
”
Home
Office
Mobile
Other
”
2
Select the number to put in the memory
Press the [1] – [6] button for at least 2 seconds.
”
”
|
34 DPX504U/ DPX404U/ DPX304
English
|
35
Display Settings
Display Setting
You can select following Display Setting items.
1
2
3
Select the source
Press the [SRC] button.
DISP
SRC
Enter Function setting mode
Press the [VOL] knob.
4 ¢
VOL
Enter Display Setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”/ “SETTINGS” > “Display &
Illumination”/ “DISP & ILLUMI”.
Function of DPX504U
Display type select
Press the [DISP] button.
4
Select the Function item
Turn the [VOL] knob and press it when the
desired item is displayed.
DPX504U
Mode
Display Type
4-line display mode Displays 3 to 4 lines of text.
3-line display mode Displays 2 to 3 lines of text.
Clock display mode Displays the clock.
Spectrum analyzer Displays a line of text and the spectrum analyzer.
display mode
Display off mode Turns off the display. Turns on temporarily when
you perform an operation.
Display
“Settings”
“Display &
Illumination”
Overview
Making Display and Illumination settings.
⁄
“Display Select” Selecting and customizing the Display type.
“Color Select” Selecting the Illumination Color of the panel.
Refer to <Illumination Color Selection>
• When the 4-line/3-line display mode is selected, the status
(ON/OFF indicator of each function) can be displayed on
the first line, and the icon of the currently selected source
and the text information title can be displayed on the left
side by the following <Information display setting> (page
39) operation.
OFF”
type select> (page 36), sets whether to turn off
display only or display and key illumination.
“DISP&ILLUMI” / “DISP”
Status display: Select “Settings” > “Display & Illumination >
“Display Select” > “Status”
Side display: Select “Settings” > “Display & Illumination” >
“Display
Dimmer”
Reduces the display Illumination brightness.
“Auto”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“Manual1”: Dims the illumination constantly.
“Manual2”: Dims the illumination darker than
Manual1.
“Display Select” > “Side Select”
“OFF”: Does not dim the illumination.
“Contrast”
“DISP N/P”
Adjusting the display contrast.
“1” - “5” - “12”
Switches the panel display between positive
or negative.
“POSI1”/ “POSI2”/ “NEGA1”/ “NEGA2”
Sets the method of scroll to view hidden text.
“Auto” : Scrolls.
“Text Scroll”
“Once” : Scrolls once.
“OFF” : Does not scroll.
“BT DVC
STATUS”
You can display the connection status, signal
strength, and battery level.
: Battery level of cell-phone.
: Signal strength of cell-phone.
|
36 DPX504U/ DPX404U/ DPX304
“ILLUMI
Dimmer”
Reduces the key Illumination brightness.
“Auto”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“Manual1”: Dims the illumination constantly.
“Manual2”: Dims the illumination darker than
Manual1.
Text scroll
Press the [DISP] button for at least 1 second.
The displayed text scrolls.
“OFF”: Does not dim the illumination.
“ILLUMI Effect” Sets whether the key illumination brightness is
changed in conjunction with the key operation.
“ON”/ “OFF”
“ILLUMI MSC Sets whether the key illumination color is
SYNC”
changed in conjunction with the sound volume.
“ON”/ “OFF”
(
: Factory setting)
DPX404U DPX304
Display
“SETTINGS”
“DISP & ILLUMI”
Overview
Making Display and Illumination settings.
“COLOR SELECT” Selecting the Illumination Color of the panel.
Refer to <Illumination Color Selection>
“TEXT SCROLL” Sets the method of scroll to view hidden text.
“AUTO” : Scrolls.
“ONCE” : Scrolls once.
“OFF” : Does not scroll.
“DISP OFF
MODE”
Sets the clock and button illumination when
“DISP OFF MODE”is selected as described in
“CLOCK”
“ON” : Displays the clock.
“OFF” : Dims the clock.
“KEY ILLUMI” “ON” : Turns on the button illumination.
“OFF” : Dims the button illumination.
“DISP DIMMER” Reduces the display Illumination brightness.
“AUTO”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“MANUAL1”: Dims the illumination constantly.
“MANUAL2”: Dims the illumination darker
than Manual1.
“OFF”: Does not dim the illumination.
“ILLUMI
DIMMER”
Reduces the key Illumination brightness.
“AUTO”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“MANUAL1”: Dims the illumination constantly.
“MANUAL2”: Dims the illumination darker
than Manual1.
“OFF”: Does not dim the illumination.
(
: Factory setting)
5
6
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
Exit Function setting mode
Press the [ ] button for at least 1 second.
English
|
37
Display Settings
Function of DPX504U
In USB/ iPod/ Audio file source
Selecting text display
4-line display mode
Song title (“Song Title”)
Play time (“P-Time”)
Changes displayed information on each of the
following sources:
Album name (“Album Name”)
Artist name (“Artist Name”)
Folder name (“Folder Name”)
File name (“File Name”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
1
2
3
Select the source
Press the [SRC] button.
Blank (“Blank”)
Enter Function setting mode
Press the [VOL] knob.
3-line display mode
Title & Artist (“Title/Artist”)
Album & Artist (“Album/Artist”)
Folder name (“Folder Name”)
File name (“File Name”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Select Text display selection mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Blank (“Blank”)
Select “Settings” > “Display & Illumination” >
“Display Select” > “Text Select”.
Play time (“P-Time”)
In Music CD source
4 Select the text display part
Turn the [VOL] knob.
The selected text display part blinks.
Disc title (“Disc Title”)
Track title (“Track Title”)
Play time (“P-Time”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
5 Select the text
Blank (“Blank”)
Press the [4] or [¢] button
In Auxiliary input source
6
Exit Function setting mode
Press the [ ] button for at least 1 second.
Source name (“Source Name”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
In FM Tuner source
4-line display mode
In Standby
Frequency & Program Service
name (“Frequency/PS”)
Song title* (“Song Title”)
Artist name* (“Artist Name”)
Station name* (“Station Name”)
Radio text plus* (“Radio Text
Plus”)
Radio text (“Radio Text”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Source name (“Source Name”)
Clock (“Clock”)
Date (“Date”)
Blank (“Blank”)
In Bluetooth audio source
4-line display mode
Bluetooth audio (“Source Name”) Spectrum analyzer & Clock
Song title* (“Song Title”)
Artist name* (“Artist Name”)
Album name* (“Album Name”)
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
* Information of Radio text plus is displayed.
3-line display mode
Frequency & Program Service
name (“Frequency/PS”)
Song title & Artist name*
(“Title/Artist”)
Station name* (“Station Name”)
Radio text plus* (“Radio Text
Plus”)
Radio text (“Radio Text”)
3-line display mode
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Bluetooth audio (“Source Name”) Spectrum analyzer & Clock
Title & Artist* (“Title/Artist”)
Album & Artist* (“Album/Artist”)
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Blank (“Blank”)
* Function of KCA-BT300
* Information of Radio text plus is displayed.
In AM Tuner source
Frequency (“Frequency”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
|
38 DPX504U/ DPX404U/ DPX304
In Disc changer source (Optional)
Function of DPX504U
Disc title (“Disc Title”)
Track title (“Track Title”)
Play time (“P-Time”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Information display setting
You can customize the display of the Spectrum
analyzer display mode.
Blank (“Blank”)
1
2
3
Select the source
Press the [SRC] button.
⁄
• Setting is available when the 4-line display mode, 3-line
display mode, Clock display mode, or Spectrum analyzer
display (Spectrum analyzer&Text type) mode which allows
• If the selected display item does not have any information,
alternative information is displayed.
Enter Function setting mode
Press the [VOL] knob.
Enter the Display Setting mode and select the
Spectrum analyzer display mode
Turn the [VOL] knob and press it when the
desired item is displayed.
• Some items cannot be selected depending on the display
type and row.
• When selecting “Folder Name” while playing with iPod,
names will be displayed depending on currently selected
browsing items.
• If the iPod Control by Hand Mode is set to on while playing
the iPod, “iPod by Hand Mode” is displayed.
Select “Settings” > “Display & Illumination” >
“Display Select”.
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
• If all characters cannot be displayed while playing with iPod,
the file number in the list is displayed.
Display
Setting
Information
Music title
Folder name
File name
Display
“Display Select”
“TITLE***”
“FLD***”
“FILE***”
“Side Select” Sets the side part display for 4-line display mode
and 3-line display mode.
Text/ Icon/ Disappear
“Graphic
Select”
Sets the spectrum analyzer display for Spectrum
analyzer display mode.
Spectrum analyzer A/ Spectrum analyzer B /
Spectrum analyzer&Text
“Clock Select” Sets the Clock display for Clock display mode.
Home/ Home&Sub
“Status”
Sets the status display (ON/OFF indicator for each
function) for 4-line display mode and 3-line display
mode.
Appear/ Disappear
5
6
Make a setting
Turn the [VOL] knob.
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• To adjust the “Sub time” with “Home & Sub” selected for
city setting> (page 43) function.
English
|
39
Display Settings
• If all characters cannot be displayed while playing with iPod,
the file number in the list is displayed.
Function of DPX404U/ DPX304
Text Display Selection
Information
Music title
Folder name
File name
Display
Changing displayed information on each source
following;
Press the [DISP] button.
“TITLE***”
“FOLDER***”
“FILE***”
In Tuner source
Information
Display
Program Service name (FM)
Song title (FM)*
“FREQUENCY/PS”
“SONG TITLE”
Artist name (FM)*
Station name (FM)*
Radio text + (FM)*
Radio text (FM)
Frequency (MW, LW)
Display off
“ARTIST NAME”
“STATION NAME”
“RADIO TEXT +”
“RADIO TEXT”
“FREQUENCY”
“DISP OFF MODE”
*Information of Radio text plus is displayed.
In CD source
Information
Disc title
Track title
Play time & Track number
Display off
Display
“DISC TITLE”
“TRACK TITLE”
“P-TIME”
“DISP OFF MODE”
In Audio file/ iPod source
Information
Display
Music title & Artist name
Album name & Artist name
Folder name
File name
Play time & Music number
Display off
“TITLE/ARTIST”
“ALBUM/ARTIST”
“FOLDER NAME”
“FILE NAME”
“P-TIME”
“DISP OFF MODE”
In Standby/ Auxiliary input source
Information
Source name
Display off
Display
“SOURCE NAME”
“DISP OFF MODE”
⁄
• When you select the Display off mode, the display setting of
each source will be changed to the Display off.
• If the selected display item does not have any information,
alternative information is displayed.
• When selecting “FOLDER NAME” while playing with iPod,
names will be displayed depending on currently selected
browsing items.
|
40 DPX504U/ DPX404U/ DPX304
Illumination Color Selection
Auxiliary Input Display Setting
Selecting the Illumination Color of the panel.
Selecting the display when changing to Auxiliary
input source.
1
Enter Function setting mode
Press the [VOL] knob.
1
Select the AUX source
Press the [SRC] button.
Select the “AUX” display.
2
Enter Illumination color selection mode
Turn the [VOL] knob and press it when the
desired item is displayed.
2
3
Enter Function setting mode
Press the [VOL] knob.
Select “Settings”/ “SETTINGS” > “Display &
Illumination”/ “DISP & ILLUMI” > “Color Select”/
“COLOR SELECT”.
Enter Auxiliary input display setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
3
4
Select the place where you want to set the
Illumination Color
Turn the [VOL] knob and press it when the
Select “Settings”/ “SETTINGS” > “AUX Name
Set”/ “AUX NAME SET”.
desired item is displayed.
4
5
Select the Auxiliary input display
Turn the [VOL] knob.
Select “AUX”, “DVD”, “PORTABLE”, “GAME”, “VIDEO”, or
Place
Display
Display and key
“All”/“ALL”
Display
Key
“Display”/“DISPLAY”
“Key”/“KEY”
“Knob”
“TV”
Exit Function setting mode
Press the [ ] button for at least 1 second.
Volume knob (DPX504U only)
Select the Illumination Color
Turn the [VOL] knob and press it when the
⁄
• The Auxiliary input display can be set only when the built-in
auxiliary input or the auxiliary input of optional KCA-S220A
is used. On the KCA-S220A, “AUX EXT” is displayed by
default.
desired item is displayed.
Select the color from “Variable Scan”/ “VARIABLE
SCAN”, “Color1”/ ”COLOR1” — “Color24”/ ”COLOR24”,
or “User”/ “USER”.
Creating “User”/”USER” color
You can create your original color during the
selection from “Color1”/ ”COLOR1” — “Color24”/
”COLOR24”.
The color you created can be called when you
select “User”/ “USER”.
1. Press the [VOL] knob for at least 1 second.
Enter the detail color adjustment mode.
2. Set the color.
Operation type
Operation
To select the color to adjust. Press the [4] or [¢] button.
(red, green, or blue)
To adjust color.
(Range: 0 – 9)
Turn the [VOL] knob.
3. Press the [VOL] knob.
Exit the detail color adjustment mode.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
English
|
41
Clock and Other Functions
desired item is displayed.
Select “Date Adjust”.
5
Adjusting Date
1. Turn the [VOL] knob to adjust the year.
2. Press the [VOL] knob.
3. Turn the [VOL] knob to adjust the month.
4. Press the [VOL] knob.
SRC
5. Turn the [VOL] knob to adjust the day.
6. Press the [VOL] knob.
DPX404U
DPX304
B.BOOST
4 ¢
VOL
6
7
8
Enter Date format mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Date Mode”.
Function of DPX504U
Clock and Date Adjustment
You can adjust the clock and date.
Select Date format
Turn the [VOL] knob and press it when the
desired item is displayed.
Select from 7 types.
Display
Overview
“Settings”
“Clock & Date”
“Clock Adjust”
“City Select”
Sets the clock.
Exit Function setting mode
Press the [ ] button for at least 1 second.
Sets the two cities to be displayed when
“Home&Sub type”is selected for“Clock
⁄
• When Radio Data System station time data is received with
“ON” selected for “Time Synchronized”, the clock is adjusted
automatically.
“Time Synchronized” Synchronizing the Radio Data System
station time data and this unit’s clock.
“ON” / “OFF”
“Sub Clock Adjust” Adjusts the time difference caused by
summer time.
“-1h” / “0h” / “+1h”
“Summer Time”
Advances the clock one hour when set
to ON.
“ON” / “OFF”
Sets the date.
Sets the date display mode.
“Date Adjust”
“Date Mode”
(
: Factory setting)
1
2
Enter Function setting mode
Press the [VOL] knob.
Enter Clock adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Clock & Date” > “Clock
Adjust”.
3
4
Adjusting Clock
1. Turn the [VOL] knob to set the hours.
2. Press the [¢] button.
3. Turn the [VOL] knob to set the minutes.
4. Press the [VOL] knob.
Enter Date adjustment mode
Turn the [VOL] knob and press it when the
|
42 DPX504U/ DPX404U/ DPX304
Function of DPX504U
Function of DPX404U/ DPX304
Dual clock city setting
Clock Adjustment
You can select cities for two clocks.
You can adjust the clock and date.
1
2
Enter Function setting mode
Press the [VOL] knob.
1
2
3
Enter Clock adjustment mode
Press the [B.BOOST] button for at least 1
second.
Select City Select mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Clock & Date” > City Select”
The hour display blinks.
Adjust the hour
Turn the [VOL] knob to adjust the hour, and
then press the [VOL] knob.
The minute display blinks.
3 Select the city display part
Turn the [VOL] knob.
The selected city display part blinks.
Adjust the minute
Turn the [VOL] knob to adjust the minute, and
then press the [VOL] knob.
Finish the Clock Adjustment.
4 Set cities for Home/ Sub
Press the [4] or [¢] button
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• To display the clocks of two cities, select “Home&Sub” type
for “Clock Select” described in <Information display setting>
• Time of Sub City is automatically derived from Home time.
When summer time systems are different between Home
and Sub cities, adjustment can be done by referring to “Sub
English
|
43
Clock and Other Functions
“Power OFF Wait”/ Setting the timer to turn this unit’s power OFF
Initial Settings
“P-OFF WAIT”
automatically when Standby mode continues.
Using this setting can save the vehicle’s battery
power.
You can select the following Initial Setting items.
1
Select the Standby
Press the [SRC] button.
“OFF”: Power OFF Timer function is OFF.
“20MIN/M”/ “40MIN/M”/ “60MIN/M”: Turns
the power OFF after minutes.
Select the “STDBY”/ “STANDBY” display.
“Built in AUX”/ When this is set to ON, AUX source can be
“BUILT-IN AUX” selected.
2
3
Enter Function setting mode
Press the [VOL] knob.
“ON”: Allows AUX source to be selected. Use
this setting when the built-in AUX terminal
is connected to the external equipment all
the time.
“OFF”: Disable AUX source selection. Use this
setting when the built-in AUX terminal is
not used.
Enter Initial Setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Initial Settings”/ “INITIAL SET”.
4
Select the setting item to adjust
Turn the [VOL] knob.
“Forced CD-DA”/ Sets the CD read mode.
“CD READ”
“Settings 1”/”1”: Automatically distinguishes
between Audio file disc and music CD when
playing disc.
Display
Overview
“Initial Settings”/
“INITIAL SET”
“Settings 2”/”2”: Forces playing as music CD.
“Built in AMP”* Selecting“OFF”turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
“Security Set”/ When Security Code is set, possibility of theft
“SECURITY SET” is reduced because input of Security Code is
prompted to turn on the unit once it is turned
off. Refer to <Activating Security Code>
“Source Select”* Sets the source selection method.
Select“2”to change the source selection
method. Press the [SRC] button, turn the [VOL]
knob to select the source, and then press the
[VOL] knob to determine it.
“ON”/ “OFF”
“Switchable
Preout”/“SWITCH subwoofer output.
PREOUT” “Rear”/ “REAR”: Rear output
“SubWoofer”/ “SUB-W”: Subwoofer output
Switches the preout between rear output and
“SP SELECT”** Fine-tuning so that the System Q value is
optimal when setting the speaker type as
follows;
“Settings 1”/ “2”
“SP OFF”: Off
“Tuner Preset
Sets the Tuner preset type.
“SP 5/4”: For 5 & 4 in. speaker
“SP 6*9/6”: For 6 & 6x9 in. speaker
“SP OEM”: For the OEM speaker
Type”/“PRESET “Type Normal”/ “TYPE NORMAL”: 1 station
TYPE”
can be assigned to 1 preset button in each
of 4 bands (FM1, FM2, FM3, and AM), i.e.,
a total of 24 stations (6 stations x 4 bands)
can be preset.
“System F/W
Upgrades the firmware.
Update”/“F/W Selecting“YES”and then pressing [VOL] knob
“Type Mixed”/ “TYPE MIXED”: A total of 6
stations can be assigned to a total of 6 preset
buttons regardless of band (FM1, FM2, FM3,
and AM). You can recall a preset station
without switching between bands.
UP”
starts upgrading the firmware.
For how to update the firmware, access our web
(
: Factory setting)
* Function of DPX504U
“Beep”/“KEY
BEEP”
Setting the operation check sound (beep sound)
ON/OFF.
“ON”/ “OFF”
** Function of DPX404U/DPX304
5
6
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
“Russian”/
When this is set to ON, the following character
“RUSSIAN SET” strings are displayed in Russian:
Folder name/ File name/ Song title/ Artist
name/ Album name/ KCA-BT200 (optional
accessory)
Exit Function setting mode
Press the [ ] button for at least 1 second.
“ON”/ “OFF”
“Menu
Language”*
You can select the display language for the
Function setting item.
“English”/ “Français”/ ”Español”/ “Deutsch”/
“Italiano”/ “Pyccкий”
|
44 DPX504U/ DPX404U/ DPX304
Demonstration mode Setting
Muting volume upon reception of
Phone call
Turning the demonstration mode ON/OFF.
The audio system automatically mutes upon
reception of an incoming call.
1
Enter Function setting mode
Press the [VOL] knob.
2
Enter Demonstration mode setting
Turn the [VOL] knob and press it when the
desired item is displayed.
When a call comes in
“CALL” is displayed.
The audio system pauses.
Select “DEMO Mode”/ “DEMO MODE”.
Listening to the audio during a call
Press the [SRC] button.
The “CALL” display disappears and the audio system
3
4
Set the Demonstration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
comes back ON.
Select “ON” or “OFF”.
When the call ends
Hang up the phone.
The “CALL” display disappears and the audio system
Exit Function setting mode
Press the [ ] button for at least 1 second.
comes back ON.
⁄
• To use the TEL Mute feature, you need to hook up the MUTE
wire to your telephone using a commercial telephone
accessory. Refer to <Connecting Wires to Terminals> (page
10) of Quick start guide.
English
|
45
Clock and Other Functions
Resetting the Security Code function when the
audio unit is first used after removed from the
battery power source or the Reset button is
pressed.
Activating Security Code
When Security Code is set, possibility of theft
is reduced because input of Security Code is
prompted to turn on the unit once it is turned off.
1
Turn the power ON.
⁄
2 Do the step 5 through 8 operation, and enter
• You can set the Security Code with a 4 digit number of your
choice.
the Security Code.
“Approved”/ “APPROVED” is displayed.
Now, you can use the unit.
• The Security Code cannot be displayed or referenced. Make
a note of the Security Code and treasure it up.
⁄
1
Select the Standby
Press the [SRC] button.
Select the “STDBY”/ “STANDBY” display.
• To deactivate the Security Code function, see the next
2
3
Enter Function setting mode
Press the [VOL] knob.
Select Security Code mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Initial Settings”/ “INITIAL SET” >
“Security Set”/ “SECURITY SET”
4
Enter Security Code mode
Press the [VOL] knob for at least 1 second.
When “Enter”/ “ENTER” is displayed, “[–][–][–][–]”/
“CODE” is also displayed.
5
6
Select the digits to enter
Press the [4] or [¢] button.
Select the Security Code numbers
Turn the [VOL] knob.
7 Repeat steps 5 and 6, and complete the
Security Code.
8
Confirm the Security Code
Press the [VOL] knob for at least 3 seconds.
When “Re-Enter”/ “RE-ENTER” is displayed, “[–][–][–]
[–]”/ “CODE” is also displayed.
9 Do the step 5 through 8 operation, and reenter
the Security Code.
“Approved”/ “APPROVED” is displayed.
The Security Code function activates.
⁄
• If you enter the wrong Code in steps 5 through 7, repeat
from step 4.
10Exit Function setting mode
Press the [ ] button for at least 1 second.
|
46 DPX504U/ DPX404U/ DPX304
Deactivating Security Code
To deactivate the Security Code function.
1
Select the Standby
Press the [SRC] button.
Select the “STDBY”/ “STANDBY” display.
2
3
Enter Function setting mode
Press the [VOL] knob.
Select Security Code mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Initial Settings”/ “INITIAL SET” >
“Security Clear”/ “SECURITY CLR”
4
Enter Security Code mode
Press the [VOL] knob for at least 1 second.
When “Enter”/ “ENTER” is displayed, “[–][–][–][–]”/
“CODE” is also displayed.
5
6
Select the digits to enter
Press the [4] or [¢] button.
Select the Security Code numbers
Turn the [VOL] knob.
7 Repeat steps 5 and 6, and complete the
Security Code.
8
Confirm the Security Code
Press the [VOL] knob for at least 3 seconds.
“Clear”/ “CLEAR” is displayed.
The Security Code function deactivates.
9
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• If a wrong security code is entered, “Error”/ “ERROR” is
displayed. Enter a correct security code.
English
|
47
Function of DPX504U
Audio Adjustments – DPX504U –
“Volume offset” Sets each source’s volume as a difference from
the basic volume.
“–8” — “ 0” (AUX: “-8”— “+8”)
“2Zone”
“2Zone Select”
“Preset”
Sets the Dual Zone System.
Sets the audio preset.
SRC
(
: Factory setting)
4 ¢
VOL
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
Audio Control
2
3
Enter Function setting mode
Press the [VOL] knob.
You can adjust the following Audio Setting items.
Display
“Audio Control”
“SubWoofer Level” You can set subwoofer level.
Overview
Enter Audio Control mode
Turn the [VOL] knob and press it when the
desired item is displayed.
“–15” — “0” — “+15”
Select “Audio Control”.
“DSP Set”
“Bypass”: Disables the DSP function.
“Through”: Enables the DSP function.
Sets the sound quality.
Sets the Bass Boost level in two steps.
“OFF”/ “Step1” – “2”
4
5
6
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
“Equalizer”
“Bass Boost”
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
“HIGHWAY-SOUND” Compensates the low volume or bass sound
being lost by road noises to make vocal sound
clearer.
Exit Function setting mode
Press the [ ] button for at least 1 second.
Unavailable when the tuner source is selected.
“OFF”/ “Step1”/ “2”/ “3”
Turns ON/OFF the Supreme plus function.
Can be set while Music CD source, Audio file
source of USB and iPod source.
Remarks
• DSP Set
“Supreme+”
“Position”
When “DSP Set” is set to “Bypass”, the DSP function is
disabled , and the colored items can not be set.
“ON”/ “OFF”
Compensates the sound environment in
accordance with the listening position.
• HIGHWAY-SOUND
Increases the volume of faintest sound being lost by road
noises to make the sound more audible. Additionally, it
accentuates bass sound being lost by road noises to make
the bass sound more dynamic.
“Balance”
“Fader”
Adjusts left/right speaker balance.
(Left) “L15” — “0” — “R15” (Right)
Adjusts front/rear speaker balance.
(Rear) “R1”5 — “0” — “F15” (Front)
• Supreme+ (Supreme Plus)
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range that is cut
off when encoding. The bass and vocal sound that are cut
off by encoding are supplemented for the reproduction
of natural sound quality. Supplementing is optimized by
compression format (AAC, MP3 or WMA) and processed
according to bit rate. The effect is negligible with music
that is encoded at high bit rate, variable bit rate or has
minimal high frequency range.
“SubWoofer”
Turns on/off the subwoofer output.
“ON”/ “OFF”
“Detailed Setup”
“Car Type”
“Speaker Setting”
“Car Type Adjust”
“X'Over”
To get clear sound, set the sound environment
according to the location and size of physically
installed speakers with reference to the
followings:
The bass and vocal sound of Music CD/ iPod is also
supplemented.
• Dual Zone System
Main source and sub source (Auxiliary input) output Front
channel and Rear channel separately.
|
48 DPX504U/ DPX404U/ DPX304
Preset Equalizer curve Select
Manual Equalizer Control
You can select the following Equalizer curve.
You can adjust the following Equalizer Control
items.
Display
“Natural”
“User”
Equalizer curve
Natural
User*
Band
Item
Range
“BAND1”(62.5 Hz) “GAIN”Band level
“EFCT”Bass Effect
“BAND2”(250 Hz) “GAIN”Band level
-9 –+9 dB
“ON”/“OFF”
-9 –+9 dB
-9 –+9 dB
-9 –+9 dB
-9 –+9 dB
: Factory setting)
“Rock”
“Pops”
“Easy”
Rock
Pops
Easy
“BAND3”(1 kHz)
“BAND4”(4 kHz)
“GAIN”Band level
“GAIN”Band level
“Top 40”
“Jazz”
Top 40
Jazz
“BAND5”(16 kHz) “GAIN”Band level
“Game”
“iPod”
Game
(
iPod (During iPod source only)
1
Select the source
Press the [SRC] button.
* The Equalizer curve set in the section <Manual Equalizer
Control> is recalled.
Select a source other than “STDBY”.
(
: Factory setting)
2
3
Enter Function setting mode
Press the [VOL] knob.
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
Enter Manual Equalizer Control mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Equalizer” > “Manual
Equalizer”.
2
3
Enter Function setting mode
Press the [VOL] knob.
Enter Preset Equalizer mode
Turn the [VOL] knob and press it when the
desired item is displayed.
4
Select the item you want to set
Select “Audio Control” > “Equalizer” >
“Preset Equalizer”.
Operation type
Selects the item.
Adjust each item.
Set the value.
Operation
Turn the [VOL] knob.
Press the [
Press the [VOL] knob.
4] or [¢] button.
4
Select the Equalizer curve
Turn the [VOL] knob.
✍ Select the iPod Equalizer curve
You can select from 22 Equalizer curve types for
iPod when “iPod” is selected.
1. Enter iPod Equalizer mode
Press the [VOL] knob.
2. Select the iPod Equalizer curve
Turn the [VOL] knob and press it when the
desired item is displayed.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
curve Select> (page 49), Manual Equalizer Control is disabled.
• You can select for each source.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• You can select for each source.
English
|
49
Function of DPX504U
Audio Adjustments – DPX504U –
Listening Position Selection
Listening Position Fine Adjustments
The sound environment can be compensated in
accordance with the selected position. According to
the listening position, select the position from the
following settings.
Making fine adjustment of the value specified at
Preset position selection per speaker.
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
Compensation seat
Not compensating.
Front-Left seat
Front-Right seat
Front seat
Display
“All”
“Front-Left”
“Front-Right”
“Front”
2
3
Enter Function setting mode
Press the [VOL] knob.
Enter Manual position setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
(
: Factory setting)
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
Select “Audio Control” > “Position” > “DTA”.
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired value is displayed.
2
3
Enter Function setting mode
Press the [VOL] knob.
Item
“Front”
“L”
“R”
“Rear”
“L”
“R”
“Subwoofer”
“L”
“R”
“Initialize”
Setting overview
Enter Preset position setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Position” > “Preset
Position”.
Front Left speaker
Front Right speaker
Rear Left speaker
Rear Right speaker
4
5
Select the seat you want to compensate
Turn the [VOL] knob.
Subwoofer Left
Subwoofer Right
Initialize the setting values.
Exit Function setting mode
Press the [ ] button for at least 1 second.
5
6
Set the value
Press the [4] or [¢] button
Adjust between 0 and 170 cm.
Exit Function setting mode
Press the [ ] button for at least 1 second.
|
50 DPX504U/ DPX404U/ DPX304
Dual Zone System
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
Display
Overview
“2Zone Rear Volume”* Adjust the volume of Rear channel.
“0” — “35”
“Detailed Setup”
“2Zone”
Sets the Dual Zone System.
“ON”/ “OFF”
“2Zone Select”*
Specifies the destination of sub source sound
when the Dual Zone function is turned on.
“Rear”/ “Front”
* The Dual Zone System is set to “ON”.
(
: Factory setting)
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
2
3
Enter Function setting mode
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup”.
4
5
Select the item you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• Select Main source by [SRC] button.
• Adjust the volume of Front channel by [VOL] knob.
• The Audio Control has no effect on sub source.
• There are following limitations when Dual Zone System is
enabled.
- There is no output from the subwoofer.
DSP function are not available.
• The Bluetooth audio source can be set exclusively to the
front speaker. Set “2Zone Select” to “Rear”.
English
|
51
Function of DPX404U/ DPX304
Audio Adjustments – DPX404U/ DPX304 –
“DETAILED SET”
“LPF
SUBWOOFER”
Selects cut off frequency of subwoofer output.
“85”/ “120”/ “160”/ “THROUGH” (OFF) Hz
“SUB-W PHASE” Selects the phase of subwoofer output.
“REVERSE” (180°)/ “NORMAL” (0°)
“SUPREME SET” Turns on/off the supreme function.
Can be set while Audio file source of CD/ USB
(excluding iPod).
SRC
“ON”/ “OFF”
Sets each source’s volume as a difference from
the basic volume.
VOL
“VOLUME
OFFSET”
“–8” — “0” (AUX: “–8” — “0” — “+8”)
Audio Control
(
: Factory setting)
You can adjust the following Audio Setting items.
1
Select the source
Press the [SRC] button.
Display
Overview
Select a source other than “STANDBY”.
“AUDIO CONTROL”
“SUBWOOFER SET” Turns on/off the subwoofer output.
2
3
Enter Function setting mode
Press the [VOL] knob.
“OFF”/ ”ON”
“SYSTEM Q”
Switches between the following preset
equalizer curves.
Enter Audio Control mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “AUDIO CONTROL”.
“NATURAL”/ “USER”/ “ROCK”/ “POPS”/
“EASY”/ “TOP40”/ “JAZZ”/ “GAME”
For USER: This appears when Bass level,
Middle level, and Treble level are
adjusted.
4
5
6
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
“BASS ADJUST”
“BASS FREQ”
You can set bass for each source.
Bass Center Frequency
40/50/60/70/80/100/120/150 (Hz)
Bass level
“–8” — “0” — “+8”
Bass Q Factor
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
“BASS LEVEL”
“BASS Q”
1.00/1.25/1.50/2.00
Bass Extend
Exit Function setting mode
Press the [ ] button for at least 1 second.
“BASS EXT”
”ON”/ “OFF”
“MID ADJUST”
“MID FREQ”
You can set middle for each source.
⁄
Middle Center Frequency
0.50/1.00/1.50/2.00 (kHz)
Middle level
“–8” — “0” — “+8”
Middle Q Factor
1.00/2.00
You can set treble for each source.
Treble Center Frequency
10.0/12.5/15.0/17.5 (kHz)
Treble level
• The “SUB-W PHASE” item can be made when a setting other
than “THROUGH” is selected for the “LPF SUBWOOFER” item.
“MID LEVEL”
“MID Q”
Remarks
• Supreme
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range that is
cut off when encoding at low bit rate (less than 128Kbps,
Sampling frequency is 44.1kHz).
Supplementing is optimized by compression format (MP3,
WMA and AAC) and processed according to bit rate. The
effect is negligible with music that is encoded at high bit
rate, variable bit rate or has minimal high frequency range.
“TRE ADJUST”
“TRE FREQ”
“TRE LEVEL”
“BALANCE”
“–8” — “0” — “+8”
Adjusts left/right speaker balance.
(Left)“L15” — “0” — “R15” (Right)
Adjusts front/rear speaker balance.
(Rear)“R15” — “0” — “F15” (Front)
You can set subwoofer level.
“–15” — “0” — “+15”
“FADER”
“SUB-W LEVEL”
|
52 DPX504U/ DPX404U/ DPX304
English
|
53
Function of DPX504U
DSP Setup
Speaker Setting
The speaker X’Over is automatically set when the
position and size of each speaker are selected from
the following items.
Speaker
“Front”
Item
“SIZE”
Range
Speaker Size Front
SRC
“O.E.M.”, “10cm”, “13cm”, “16cm”,
“17cm”, “18cm”, “4x6”, “5x7”, “6x8”,
“6x9”, “7x10”
4 ¢
VOL
“LOCATION” Speaker Location Front
“Door”, “On Dash”, “Under Dash”
“TWEETER” Speaker Size Tweeter
Car Type Selection
“None”, “Use”
Speaker Size Rear
“None”, “O.E.M.”, “10cm”, “13cm”,
“16cm”, “17cm”, “18cm”, “4x6”, “5x7”,
“6x8”, “6x9”, “7x10”
You can compensate the delay of the sound arrival
time by selecting your environment from the
following car types.
“Rear”
“SIZE”
Display
Overview
“LOCATION” Speaker Location Rear
“OFF”
“Compact”
“Sedan”
Not compensating.
Compact car
Sedan
• “Door”, “Rear Deck”
• “2nd Row”, “3rd Row” (Car Type:
“Minivan”, “Passenger Van”)
“Wagon”
“Minivan”
“SUV”
Station wagon
Minivan
Sport-utility vehicle
Passenger van
“SubWoofer” “SIZE”
Speaker Size Subwoofer
“None”, “16cm”, “20cm”, “25cm”,
“30cm”, “38cm Over”
“Passenger Van”
(
: Factory setting)
(
: Factory setting)
1
Select the source
Press the [SRC] button.
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
Select a source other than “STDBY”.
2
3
Enter Function setting mode
Press the [VOL] knob.
2
3
Enter Function setting mode
Press the [VOL] knob.
Enter Speaker setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“Speaker Setting”.
Enter Cabin select mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“Car Type”.
4
5
Select the item you want to set
4
5
Select the car type
Turn the [VOL] knob to select the car type, and
then press the [VOL] knob.
Operation type
Selects the item.
Adjust each item.
Set the value
Operation
Turn the [VOL] knob.
Press the [
Press the [VOL] knob.
4] or [¢] button.
Exit Function setting mode
Press the [ ] button for at least 1 second.
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• You can compensate the distances in more details by using
<Car Type Fine Adjustments> (page 55) function.
|
54 DPX504U/ DPX404U/ DPX304
Reference point
Car Type Fine Adjustments
Adjusting fine tuning of the speaker position
compensation value specified at <Car Type
+100cm
FRONT
FRONT
REAR
Display
“FRONT”
“REAR”
“SW”
Item
Range
50cm
Front speaker
Rear speaker
Subwoofer
0 – 440 cm
0 – 440 cm
0 – 440 cm
80cm
REAR
+70cm
(
: Factory setting)
150cm
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
+0cm
SUB-W
2
3
Enter Function setting mode
Press the [VOL] knob.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
Enter Car Type Adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“Car Type Adjust”.
4
Select the item you want to set
Operation type
Selects the item.
Adjust each item.
Set the value
Operation
Turn the [VOL] knob.
Press the [
Press the [VOL] knob.
4] or [¢] button.
The settings of the delay time are automatically
identified and compensated by specifying the
distances of each speaker from the center of the
vehicle interior.
1 Set the front and rear positions and the height
of the reference point to the position of the ears
of the person sitting in the front seat, and set
the right and left positions to the center of the
vehicle interior.
2 Measure the distances from the reference point
to the speakers.
3 Calculate the distance difference in accordance
with the farthest speaker.
English
|
55
Function of DPX504U
DSP Setup
X’Over Setting
Audio Preset Memory
Fine adjusting the following setting values
corresponding to the X’Over values set in the
Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
Sound Control.
Display
Item
Range
“X’Over”
“Front”
“FC”
Front High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE” Front High Pass Slope
-6, -12, -18, -24 dB/Oct
Rear High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“Rear”
“FC”
2
Enter Audio preset memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“Preset” > “Preset Memory”.
“SLOPE” Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
Subwoofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through (Hz)
“SubWoofer” “FC”
“SLOPE” Subwoofer Slope
-6, -12, -18, -24 dB/Oct
“PHASE” Subwoofer Phase
Reverse (180°)/ Normal (0°)
3
4
Select the number to put in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a preset number.
(
: Factory setting)
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
“Memory Completed” is displayed.
2
3
Enter Function setting mode
Press the [VOL] knob.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
Enter X’Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“X’Over”.
⁄
• Register 6 patterns of Audio Preset Memory.
• Preset number “1”:
When you press the Reset, all the sources will be the setting
value which is registered.
• Preset number “1” and “2”:
4
5
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
The memory cannot be erased by the Reset button.
• This function cannot be registered when the iPod Equalizer
Select “Front”, “Rear”, or “SubWoofer”.
Select the item you want to set
Operation type
Selects the item.
Adjust each item.
Set the value
Operation
Turn the [VOL] knob.
Press the [
Press the [VOL] knob.
4] or [¢] button.
6
7
Repeat steps 4 to 5 to complete the X’Over
settings.
Exit Function setting mode
Press the [ ] button for at least 1 second.
|
56 DPX504U/ DPX404U/ DPX304
Audio Preset Recall
Recalling the sound setup registered by <Audio
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
2
3
Enter Function setting mode
Press the [VOL] knob.
Enter Audio preset recall mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control” > “Detailed Setup” >
“Preset” > “Preset Recall”.
4
5
Select the number to recall in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select preset number.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
“Recall Completed” is displayed.
6
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
changed to the value which was recalled.
• The Equalizer curve is changed to the value which was
recalled by the selected source.
English
|
57
Function of DPX504U
Log Function
Log Function item lock
Locks the Log Function items to prevent them from
being deleted automatically.
1 Display the Log Function list
Press the [LOG] button.
2 Lock the Log Function item
Turn the [VOL] knob to select item, and then
press the [VOL] knob for at least 1 second.
Locked items are indicated with “ ”.
Performing this step again will unlock the locked
item.
VOL
LOG
Log Function recall
This unit automatically memorizes the previously
used functions and Function setting items, which
can easily be recalled.
3 Exit Log Function
Press the [
] button.
1 Display the Log Function list
Press the [LOG] button.
2 Recall the desired function
Turn the [VOL] knob to select Log Function
item, and then press the [VOL] knob.
Category display
“FM”
Function category
FM broadcast
“MW/LW”
“iPod”
AM broadcast
iPod music
“USB”
USB music
“CD”
CD music
“INIT”
“SET”
Initial setting item
Setting item
“DISP”
“AUD”
“BT”
Display setting item
Audio control setting
Calling number
Cancelling the Log Function recall
Press the [ ] button.
⁄
•
•
•
•
•
Maximum of 15 recently used functions are logged. When this
limit is reached, they are deleted from the oldest.
Logged functions can be deleted. Refer to <Deleting a Log
Functions to be logged can be set by categories. Refer to
Logged functions can be locked to avoid them being deleted.
Stations are logged after 1 minutes of reception.
This timing can be changed. Refer to <Tuner Log Function
|
58 DPX504U/ DPX404U/ DPX304
Deleting a Log Function item
Log Function category setting
Deletes Log Function items.
Sets the function category to be logged.
1
Enter Function setting mode
Press the [VOL] knob.
1
Enter Function setting mode
Press the [VOL] knob.
2 Select the Log delete mode
2 Select the Log Function setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Log” > “Log Delete”
Select “Settings” >“Log” >“Log settings”
3 Select the Log Function item to delete
Turn the [VOL] knob to select Log Function
item, and then press the [VOL] knob.
Selecting “All” deletes all Log Function. (exclude a
locked items.)
3 Set the category to be logged
Category display
“Tuner Log”
Setting category
Radio-related
“Data CD Log”
“iPod Log”
CD-related
iPod-related
“USB Log”
“Phone Log”
“Function Log”
USB-related
Call-related (KCA-BT200/BT300 only)
Function setting-related
4 Turn the [VOL] to select “YES”, and then press
the [VOL] knob.
“Completed” is displayed.
Turn the [VOL] knob to select category, and
then press the [VOL] knob.
Check-mark (“✔”) the category you want to register.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
4
Exit Function setting mode
Press the [ ] button for at least 1 second.
English
|
59
Function of DPX504U
Log Function
Tuner Log Function time setting
You can set the timing to log the station by the
reception time.
1
Enter Function setting mode
Press the [VOL] knob.
2 Select the Tuner Log time set mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” >“Log” >“Tuner Log Time Set”
3 Set the reception time for the timing to start
logging the station
Turn the [VOL] knob to select time (“10SEC”,
“30SEC”, “1MIN”, “2MIN”, or “5MIN”), and then
press the [VOL] knob.
4
Exit Function setting mode
Press the [ ] button for at least 1 second.
|
60 DPX504U/ DPX404U/ DPX304
English
|
61
Function of DPX504U with KCA-BT200/BT300 (Optional Accessory)
Bluetooth Setup
“Bluetooth HF/ You can specify output speakers for hands-free
Audio”
voice communication and Bluetooth audio
sound.
“Front”: Outputs voice from the front speakers.
“All”: Outputs voice from the front and rear
speakers.
“Call Beep”
You can output a beep from the speaker when
a call comes in.
“ON”: Beep is heard.
“OFF”: Beep is canceled.
4 ¢
LOG VOL
“BT F/W Update” Display the version of the firmware of this unit.
“Mic Gain”*
Adjust the sensitivity of the microphone for a
telephone call. Adjust the voice of caller. Setting
to“+”increases the voice volume.
“–3” – “0” – “+3”
Bluetooth Setting
You can select the following Bluetooth Setting
items.
“NR Level”*
Reduce the noises generated by surrounding
environment without changing the microphone
volume. Adjust the voice of caller when it is
not clear. Setting to“+”increases the noise
reduction.
1 Press the [LOG] button for at least 1 second.
2
Turn the [VOL] knob and press it when the
desired item is displayed.
“–3” – “0” – “+3”
Select “Settings”.
“Echo Cancel
Level“*
Adjust the level of echo cancellation. Setting to
“+”increases the echo cancel reduction.
“–2” – “0” – “+2”
3
Select the Setting item
Turn the [VOL] knob and press it when the
(
: Factory setting)
desired item is displayed.
* Function of KCA-BT300
Display
“Settings”
“PAIRING”
“Device
Overview
4
5
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
Register a Bluetooth device (pairing).
Refer to <Registering Bluetooth device>
Select a cell-phone or Bluetooth audio player
connection.
Registration”
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
“Phone
Selection”
Remarks
• “Auto Answer” (Setting the Time Interval for Automatic
Answer)
Refer to <Selecting the Bluetooth device You
“Audio Selection”
This function automatically answers (responds to) a call
after lapse of the preset time interval for automatic answer.
“OFF” : Does not answer the phone call automatically.
“0” : Automatically answers the phone call at once.
“1s” – “99s” : Automatically answers the phone call after
lapse of 1 – 99 seconds.
“Special Device Register a Bluetooth device (pairing).
Select”
Refer to <Registering Bluetooth device>
“Device Delete” Cancel registration of the Bluetooth device.
Refer to <Deleting a Registered Bluetooth
“SMS Download” Download a short message.
“Voice Tag”
Registers voice for voice recognition and voice
to select the Phone number category in Phone
book.
“Detailed Setup” Move to detailed item.
“PIN Code Edit” Specify the PIN code required when registering
this unit using the Bluetooth device.
“Auto Answer” Answer a call automatically after lapse of the
preset time interval for automatic answer.
“OFF”/ “0SEC” – “8SEC” – “99SEC”
|
62 DPX504U/ DPX404U/ DPX304
⁄
• If the time set in the cell-phone is shorter than that set in
the unit, the former will be used.
• This function does not work for call waiting.
• “Bluetooth HF/Audio” (Setting up the Voice Output
Speakers)
Select the speaker which is further from the microphone in
order to prevent howling or echoes.
• “BT F/W Update” (Displaying the Firmware Version)
Display the version of the firmware of this unit.
For how to update the firmware, access our web site.
English
|
63
Function of DPX504U with KCA-BT200/BT300 (Optional Accessory)
Bluetooth Setup
Select”.
Registering Bluetooth device
2. Enter Special device registration mode
Press the [VOL] knob.
A list is displayed.
3. Select a device name
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing). You
can register up to 5 Bluetooth devices to this unit.
Turn the [VOL] knob and push the center when
the desired device name is displayed.
If “Completed” is displayed, registration is
completed.
4. Go through the procedure step 3 of
complete the registration (pairing).
Cancelling Special device registration mode
Press the [ ] button for at least 1 second.
Registering from this unit
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
2
Enter Bluetooth device registration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “PAIRING” > “Device
Registration”.
Search for the Bluetooth device.
When search is completed, “Finished” is displayed.
⁄
• If the device name is not in the list, select “Other Phones”.
3
4
Select a Bluetooth device
Turn the [VOL] knob and press it when the
desired item is displayed.
Input the PIN code
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Press the [
Press the [
¢
] button.
] button.
4
5
Transmit the PIN code
Press the [VOL] knob.
If “Pairing Success” is displayed, registration is
completed.
✍ If the error message appears even though the
PIN code is correct, try <Registering Special
6
7
Return to the device list
Press the [ ] button.
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
• This unit allows up to eight digits to be input for a PIN code.
If a PIN code cannot be input from this unit, it can be input
from the Bluetooth device.
• If there are 5 or more Bluetooth devices registered, you
cannot register a new Bluetooth device.
Registering Special Bluetooth device
Allow registration of a special device that cannot be
registered normally (pairing).
1. Select Special device registration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “PAIRING” > “Special Device
|
64 DPX504U/ DPX404U/ DPX304
Registering PIN Code
Selecting the Bluetooth device You
Wish to Connect
By operating the Bluetooth device, specify the PIN
code necessary for registering this unit.
When two or more Bluetooth devices have already
been registered, you need to select the Bluetooth
device you wish to use.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
2
Enter PIN code edit mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Detailed Setup” > “PIN
Code Edit”.
2
Select Bluetooth device selection mode
Turn the [VOL] knob and press it when the
desired item is displayed.
The current setting of PIN code is displayed.
Cell-phone
3
Input the PIN code
Select “Settings” > “PAIRING” > “Phone
Selection”.
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Audio player
Select “Settings” > “PAIRING” > “Audio
Selection”.
Press the [
Press the [
¢
] button.
] button.
4
3
Enter Bluetooth device selection mode
Press the [VOL] knob.
“(name)” is displayed.
4
5
Register a PIN code
Press the [VOL] knob.
If “Completed” is displayed, registration is
completed.
4
5
Select the Bluetooth device
Turn the [VOL] knob.
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
Set up the Bluetooth device
Press the [VOL] knob.
“✱(name)” or “-(name)” is displayed.
“✱”: The selected Bluetooth device is busy.
“-”: The selected Bluetooth device is on standby.
“ “ (blank): The Bluetooth device is deselected.
⁄
• By default, “0000” is specified.
• A PIN code can be specified with up to eight digits.
6
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
• If a Bluetooth device is already selected, deselect it, and
then select a different one.
• If you cannot select a device using the audio player,
connect the device with the audio player.
English
|
65
Function of DPX504U with KCA-BT200/BT300 (Optional Accessory)
Bluetooth Setup
Deleting a Registered Bluetooth
device
Downloading the Phone Book
Download the phone book data from the cell-
phone to this unit so that you can use the Phone
Book of this unit.
You can delete a registered Bluetooth device.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
To download automatically
If the cell-phone supports a phone book
synchronization function, the phone book is
downloaded automatically after Bluetooth
connection.
2
Enter Bluetooth device deletion mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “PAIRING” > “Device Delete”.
“(name)” is displayed.
⁄
• Setting on the cell-phone may be required.
• If no phone book data is found in the unit even after
the compete display, your cell-phone may not support
automatic download of phone book data. In this case, try
downloading manually.
3
Select the Bluetooth device
Turn the [VOL] knob.
4
5
Delete the selected Bluetooth device
Press the [VOL] knob.
To download from the cell-phone manually
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
1
By operating the cell-phone, end the hands-free
connection.
“Completed” is displayed.
2
By operating the cell-phone, send the phone
book data to this unit
6
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
By operating the cell-phone, download the phone
book data to this unit.
• During downloading:
⁄
• When a registered cell-phone is deleted, its Phone Book,
“Downloading”/ “Download..” is displayed.
• After completion of downloading:
“Completed” is displayed.
log, SMS, and voice tag are also deleted.
3
By operating the cell-phone, start the hands-
free connection.
To clear the downloading completion message
Press any button.
⁄
• Up to 1000 phone numbers can be registered for each
registered cell-phone.
• Up to 32 digits can be registered for each phone number
along with up to 50* characters representing a name.
(* 50: Number of alphabetic alphabetical characters.
Fewer characters can be input depending on the type of
characters.)
• To cancel downloading of the phone book data, operate
the cell-phone.
|
66 DPX504U/ DPX404U/ DPX304
Select“PB Name Check” (Play)
Press the [VOL] knob.
Select“PB Name Delete” (Delete)
Adding a Voice Dialing Command
5
Add a voice tag to the phone book for voice dialing.
You can register up to 35 voice tags.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
5
6
Delete a voice tag
Press the [VOL] knob.
2
Enter Phone book name edit mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Voice Tag” > “PB Name
Edit”.
Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
3
4
Search for the name to register
• Audio sound is not output during voice tag registration.
Select the name to register with reference to 4 in
If a voice tag has already been registered for a
name, “*” is displayed before the name.
Select a mode
Turn the [VOL] knob.
Display
Operation
“PB Name Regist.”
“PB Name Check”*
“PB Name Delete”*
Register a voice tag.
Play a voice tag.
Delete a voice tag.
* Displayed only when a name for which a voice tag has
been registered is selected.
Select“PB Name Regist.” (Regist)
5
Register a voice tag (first)
“Enter Voice 1” is displayed.
When a beep is heard, say a voice tag within 2
seconds.
6
Confirm the voice tag (second)
“Enter Voice 2” is displayed.
When a beep is heard, say the same voice tag as
that you said in step 6 within 2 seconds.
“Completed” is displayed.
7
End registration
Press the [VOL] knob.
Return to step 2. You can register another voice tag
continuously.
⁄
• If your voice cannot be recognized, a message is displayed.
Pressing the [VOL] knob allows you to retry voice input.
English
|
67
Function of DPX504U with KCA-BT200/BT300 (Optional Accessory)
Bluetooth Setup
Setting a Voice Command for
Category
Add a voice tag to the phone number category
(type) for voice calling.
1
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
2
Enter Phone Number type edit mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Voice Tag” > “PN Type Edit”.
3
4
Select the category (type) you wish to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “General”, “Home”, “Office”, “Mobile”, or
“Other”
Select a mode
Turn the [VOL] knob.
Display
Operation
“PN Type Regist.”
“PN Type Check”*
“PN Type Delete”*
Register a voice tag.
Play a voice tag.
Delete a voice tag.
* Displayed only when a name for which a voice tag has
been registered is selected.
5
6
Register the category (type) by performing
steps 5 to 7 in <Adding a Voice Dialing
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
• Set the voice tag for all the 5 categories. If the voice tag is
not registered for all the categories, the Phone book may
not be recalled by voice command.
|
68 DPX504U/ DPX404U/ DPX304
English
|
69
Function of DPX504U with KCA-BT200/BT300 (Optional Accessory)
SMS (Short Message Service)
SMS (Short Message Service)
The SMS arrived at the cell-phone is displayed on
the receiver.
A newly arrived message is displayed.
¤
• To prevent car accidents, the driver should not read the
SMS while driving.
VOL
LOG
When a new message arrives
“SMS Received” is displayed.
The display disappears with any operations.
Downloading the SMS
Displaying the SMS
Download the short message (SMS) arrived at the
cell-phone so that it can be read on this unit.
1
2
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
✍ You can also select from “Settings” in Function
setting mode.
1
2
3
Enter Bluetooth mode
Press the [LOG] button for at least 1 second.
✍ You can also select from “Settings” in Function
setting mode.
Enter SMS Inbox mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “SMS Inbox”.
Enter SMS download mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “SMS Download”.
A message list appears.
3
4
Select a message
Turn the [VOL] knob.
Each pressing of the [DISP] button switches
between telephone number or name and message
reception date.
Start downloading
Press the [VOL] knob.
“Downloading” is displayed.
When the downloading finishes, “Completed” is
displayed.
Display the text
Press the [VOL] knob.
Turning the [VOL] knob scrolls the message.
Pressing the [VOL] knob again returns to the
message list screen.
4
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
• The cell-phone must be able to transmit the SMS using
Bluetooth. Setting on the cell-phone may be required. If
the cell-phone does not support SMS function, the SMS
download item in Function Control mode is not displayed.
• When the SMS is downloaded from the cell-phone, the
unopened messages in the cell-phone are opened.
• The already-read and unread short messages can be
respectively downloaded up to 75.
5
6
Exit SMS Inbox mode
Press the [ ] button.
Exit BT Settings mode
Press the [LOG] button for at least 1 second.
⁄
• The unopened message is displayed at the beginning of the
list. Other messages are displayed in the order of reception.
• The SMS that has arrived when the cell-phone is not linked
with Bluetooth cannot be displayed. Download the SMS.
• The short message cannot be displayed during
downloading the SMS.
|
70 DPX504U/ DPX404U/ DPX304
English
|
71
Appendix
About Audio file
About USB device
•
Playable Audio file
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
•
Playable disc media
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Save backups of the Audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
• When connecting the USB device, usage of the
CA-U1EX (option) is recommended.
• Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 4 m can result in abnormal playback.
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
•
•
Playable USB device
USB mass storage class
Playable USB device file system
FAT16, FAT32
Even if the Audio files comply with the standards
listed above, the play may be impossible depending
on the types or conditions of media or device.
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
•
^
¡
:
Folder
CD
(1)
:
A
udiofile
¡!
2
3
¡"
¡#
4
¡$
5
¡%
¡P
An online manual about Audio files is put on the site,
www.kenwood.com/cs/ce/audiofile/. On this online
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
⁄
• In this manual, the word “USB device” is used for flash
memories and digital audio players which have USB
terminals.
|
72 DPX504U/ DPX404U/ DPX304
iPod/iPhone that can be connected to this
About “KENWOOD Music Editor”
• This unit supports the PC application “KENWOOD
Music Editor Light ver1.1” or later.
unit
Made for
• When you use the Audio file with database
information added by the “KENWOOD Music Editor
Light ver1.1”, you can search a file by title, album or
• iPod nano (6th generation) • iPod nano (5th generation)
• iPod nano (4th generation) • iPod nano (3rd generation)
• iPod nano (2nd generation) • iPod nano (1st generation)
• iPod with video
• iPod classic
• iPod touch (4th generation) • iPod touch (3rd generation)
• iPod touch (2nd generation) • iPod touch (1st generation)
• In the Instruction manual, the term “Music Editor
media” is used to mean the device that contains
Audio files with database information added with
KENWOOD Music Editor.
• iPhone 4
• iPhone 3GS
• iPhone
• iPhone 3G
• “KENWOOD Music Editor Light ver1.1” is available
from the following web site:
• For further information on “KENWOOD Music
Editor Light ver1.1”, refer to the site above or the
application help.
• For information on the compatibility of iPod/iPhone
• Type of control available varies depending
on the type of connected iPod. See
www.kenwood.com/cs/ce/ipod/ for further details.
• The word “iPod” appearing in this manual indicates
the iPod or the iPhone connected with the iPod
connection cable* (optional accessory).
* Not supported model KCA-iP500.
• Refer to the web site for connectable iPod and iPod
connection cable.
⁄
• If you start playback after connecting the iPod, the music
that has been played by the iPod is played first.
In this case, “RESUMING” is displayed without displaying a
folder name, etc. Changing the browse item will display a
correct title, etc.
• You cannot operate iPod if “KENWOOD” or “✓” displayed on
iPod.
English
|
73
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
!
• Cannot set up the subwoofer.
• No output from the subwoofer.
• Cannot set up the subwoofer position of Manual
position setting.
General
? The operation check sound (beep sound) does not
not set to ON.
sound.
✔
The preout jack is being used.
The Touch Sensor Tone cannot be output from
the preout jack.
? The illumination flashes when the knob or button
is operated.
set to “Through”/ “THROUGH”.
• In the speaker select option, None is selected for
✔
This is the key illumination effect.
You set this effect in “ILLUMI Effect” of <Display
? The key illumination effect brought about in
conjunction with the sound volume is small.
!
!
• Cannot set up the equalizer.
• Cannot set up the Bass Boost.
• Cannot set up the Highway sound.
• Cannot set up the Supreme.
• Cannot set up the Position control.
• In the speaker select option, None is selected for
✔
The key illumination effect may be insufficient
depending on the sound volume and sound quality.
Tuner source
? Radio reception is poor.
✔
The car antenna is not extended.
Connect the Antenna control wire to the power
terminal for the booster amplifier of the film-type
or short pole type antenna
Pull the antenna out all the way.
• Cannot select the output destination of the
subsource in the Dual zone.
Disc source
• Cannot adjust the volume of the rear speakers.
? The specified disc does not play, but another one
plays instead.
✔
✔
The specified CD is quite dirty.
Clean the CD, referring to the CD cleaning of the
!
!
!
Cannot set up Display.
turned off.
The disc is loaded in a different slot from that
specified.
Eject the disc magazine and check the number
for the specified disc.
Cannot switch to USB/iPod source.
✔
The disc is severely scratched.
Try another disc instead.
Audio file source
The number of songs contained in “SONGS”
category of this unit is different from that
contained in “SONGS” category of iPod.
Podcast files are not counted in this unit as this unit
does not support the playback of podcast files.
? The sound skips when an Audio file is being
played.
✔
✔
The media is scratched or dirty.
Clean the media, referring to the CD cleaning of
The recording condition is bad.
Record the media again or use another media.
|
74 DPX504U/ DPX404U/ DPX304
Hands-free
? The hands-free talk volume is low.
✔
The hands-free talk volume is set at a low level.
The hands-free talk volume can be adjusted
independently. Adjust it during hands-free talk.
“Mic Gain” and “NR Level” <Bluetooth Setting>
? No sound is heard from the rear speakers.
You are talking in the hand-free talk mode.
✔
No sound is heard from the rear speakers in the
hands-free talk mode.
? No beep is heard at reception of an incoming call.
✔
No beep is heard depending on the type of your
cell-phone.
set ON.
? Voice is not recognized.
✔
✔
✔
The vehicle window is open.
If the surrounding noise is large, voice cannot be
recognized properly. Close the vehicle windows
to reduce noise.
Small voice.
If voice is too small, it cannot be recognized
properly. Speak into the microphone a little more
loudly and naturally.
The person uttering the voice tag is not the one who
registered the it.
Only the voice of the person who registered the
voice tag can be recognized.
Bluetooth audio source
? The Bluetooth audio player cannot be registered
(pairing).
✔
The PIN code is fixed.
When a PIN code is specified in the Instruction
Manual for Bluetooth Audio Player, register it
with reference to <Registering PIN Code> (page
65) to register the Bluetooth audio player. If no PIN
code is specified in the Instruction Manual, try
“0000”.
? The sound from the Bluetooth audio player is
discontinuous.
✔
The distance between this unit and audio player is
too far.
Move the audio player nearer to this unit.
✔
Another Bluetooth device is affecting the Bluetooth
communication.
Turn off another Bluetooth device.
Move another Bluetooth device away from this
unit.
✔
Another Bluetooth device or profile is used for
communication.
The downloading of the Phone book or the SMS
disconnects the sound.
English
|
75
Troubleshooting Guide
N/A Device/NA DEVICE:
• An unsupported USB device is connected.
The messages shown below display your
systems condition.
• Connection to the iPod has failed.
Remove the USB device and then
reconnect it.
Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 72) for information on supported
iPods.
TOC Error/TOC ERROR:
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
Error 05/ERROR 05:
Reset iPod/ iPhone.
The disc is unreadable.
No Music Data/Error 15/No Music/NO MUSIC/EROOR 15:
• The connected USB device contains no
playable Audio file.
Mecha Error/Mecha ERR/Error 77/ERROR 99/ERROR 77:
The unit is malfunctioning for some reason.
Press the reset button on the unit. If the
“Mecha Error”/ “Mecha ERR”/ “Error 77”/
“ERROR 99”/ “ERROR 77” code does not
disappear, consult your nearest service
center.
• Media was played that does not have data
recorded that the unit can play.
USB Error/USB ERROR:
Some trouble may have occurred to the
connected USB device.
Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
IN (Blink):
The CD player section is not operating
properly.
Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
iPod Error/iPod ERROR:
Connection to the iPod has failed.
Remove the USB device and then
reconnect it.
Protect/PROTECT (Blink):
The speaker wire has a short-circuit or
Reset iPod/ iPhone.
No Number:
No Data:
• The calling party does not notify a caller ID.
• There is no phone number data.
touches the chassis of the vehicle, and then
the protection function is activated.
Wire or insulate the speaker cable properly
and press the reset button. If the “Protect”
code does not disappear, consult your
nearest service center.
• There is no outgoing call list.
• There is no incoming call list.
• There is no missed call list.
• There is no phone book list.
Unsupported File/NA FILE:
No Entry:
The cell-phone has not been registered
(pairing).
An Audio file is played with a format that this
unit can’t support.
HF Disconnect/HF D-CON:
The unit cannot communicate with the cell-
Copy Protection/COPY PRO:
A copy-protected file is played.
phone.
Read Error/READ ERROR:
HF Error 07:
The memory cannot be accessed.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
The file system of the connected USB device
is broken.
Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
HF Error 68:
The unit cannot communicate with the cell-
phone.
Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
No Device/NO DEVICE:
The USB device is selected as a source
although no USB device is connected.
Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
Unknown:
The Bluetooth device cannot be detected.
Device Full:
5 Bluetooth device have already been
registered. No more Bluetooth device cannot
be registered.
PIN Code NG: The PIN code is wrong.
Connect NG: The unit cannot be connected to the device.
Pairing Failed: Pairing error.
|
76 DPX504U/ DPX404U/ DPX304
Err No Matching:
The voice tag is wrong. Voice cannot be
recognized because of an unregistered voice
tag, etc.
Too Soft:
Too Loud:
Too Long:
Voice is too small and cannot be recognized.
Voice is too large to be recognized.
The word or utterance is too long to be
recognized.
No Phonebook: Data is not contained in the phone book.
No Message: No short message in In Box.
No Record:
The voice tag is not registered in the phone
book.
Memory Full: The number of voice tags reaches the
maximum number to be registered in the
phone book.
No Voice:
No call.
English
|
77
Specifications
FM tuner section
USB Interface (DPX504U/ DPX404U)
Frequency range (50 kHz space)
: 87.5 MHz – 108.0 MHz
USB Standard
: USB1.1/ 2.0 (Full speed)
Usable sensitivity (S/N = 26dB)
DPX504U: 0.7 μV/75 Ω
Maximum Supply current
: 500 mA
DPX404U/ DPX304: 1 μV/75 Ω
Quieting Sensitivity (S/N = 46dB)
DPX504U: 1.6 μV/75 Ω
File System
: FAT16/ 32
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC ”.m4a” files
DPX404U/ DPX304: 2.5 μV/75 Ω
Frequency response ( 3.0 dB)
: 30 Hz – 15 kHz
Signal to Noise ratio (MONO)
DPX504U: 65 dB
DPX404U/ DPX304: 63 dB
Stereo separation (1 kHz)
: 40 dB
Audio section
Maximum output power
: 50 W x 4
Output power (DIN 45324, +B=14.4V)
: 30 W x 4
Speaker Impedance
: 4 – 8 Ω
MW tuner section
Frequency range (9 kHz space)
: 531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB)
DPX504U: 25 µV
DPX404U/ DPX304: 36 µV
Tone action
DPX504U
BAND1 (60 Hz): 9 dB
BAND2 (250 Hz): 9 dB
BAND3 (1 kHz): 9 dB
BAND4 (4 kHz): 9 dB
BAND5 (16 kHz): 9 dB
DPX404U/ DPX304
LW tuner section
Frequency range
: 153 kHz – 279 kHz
Usable sensitivity (S/N = 20dB)
DPX504U: 45 µV
DPX404U/ DPX304: 57 µV
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 12.5 kHz 8 dB
CD player section
Laser diode
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 24 Bit
Spindle speed
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Total harmonic distortion (1 kHz)
: 0.008 %
Preout level / Load (CD)
DPX504U: 2500 mV/10 kΩ
DPX404U/ DPX304: 2000 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
Auxiliary input
Frequency response ( 1 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 10 kΩ
Signal to Noise ratio (1 kHz)
General
: 110 dB
Operating voltage (11 – 16V allowable)
: 14.4 V
Maximum Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 111 x 158 mm
Weight
: 1.5 kg
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC “.m4a” files
Specifications subject to change without notice.
|
78 DPX504U/ DPX404U/ DPX304
This Product is not installed by the manufacturer of a vehicle on the
production line, nor by the professional importer of a vehicle into an EU
Member State.
Declaration of Conformity with regard to
the EMC Directive 2004/108/EC
Information on Disposal of Old Electrical and Electronic
Equipment and Batteries (applicable for EU countries
that have adopted separate waste collection systems)
Manufacturer:
Products and batteries with the symbol (crossed-out
wheeled bin) cannot be disposed as household waste.
Old electrical and electronic equipment and batteries
should be recycled at a facility capable of handling these
items and their waste byproducts.
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
EU Representative’s:
Kenwood Electronics Europe BV
Contact your local authority for details in locating a recycle
facility nearest to you.
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
Proper recycling and waste disposal will help conserve
resources whilst preventing detrimental effects on our
health and the environment.
Notice: The sign “Pb” below the symbol for batteries
indicates that this battery contains lead.
The marking of products using lasers
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and says that the component
uses laser beams that have been classified as Class 1. It means that the
unit is utilizing laser beams that are of a weaker class. There is no danger
of hazardous radiation outside the unit.
This symbol mark indicates that Kenwood
manufactured this product so as to
decrease harmful influence on the
environment.
• The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Kenwood Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
• The “AAC” logo is a trademark of Dolby Laboratories.
• iTunes is a trademark of Apple Inc.
• “Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod or iPhone, respectively, and has
been certified by the developer to meet Apple
performance standards. Apple is not responsible for
the operation of this device or its compliance with
safety and regulatory standards. Please note that the
use of this accessory with iPod or iPhone may affect
wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch
are trademarks of Apple Inc., registered in the U.S. and
other countries.
• “Adobe Reader” is a trademark of Adobe Systems
Incorporated.
For Turkey
Bu ürün 26891sayılı Resmi Gazete’de yayımlanan Elektrikli
ve Elektronik Eşyalarda Bazı Zararlı Maddelerin Kullanımının
Sınırlandırılmasına Dair Yönetmeliğe uygun olarak üretilmiştir.
This product complies with Directive, Number 26891
regarding “REGULATION ON THE RESTRICTION OF THE USE
OF CERTAIN HAZARDOUS SUBSTANCES IN LECTRICAL AND
ELECTRONIC EQUIPMENT”.
English
|
79
|