Kambrook Hot Beverage Maker KQK600 User Manual

Hot Cup  
Rapid Boil  
2400W Rapid Boil  
Suits all KQK600 models  
 
KQK600_HOTCUP_IB_FA.indd  
1
19/6/09 4:00:16 PM  
Do not move the Hot Cup while it is switched on.  
Do not open the lid during operation.  
Keep the Hot Cup clean. Follow the cleaning  
instructions provided in this book.  
IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES  
Fully unwind the power cord before use.  
Any maintenance other than cleaning should be  
performed at an authorised Kambrook Service  
Centre.  
Do not let the power cord hang over the edge of  
a bench or table, touch hot surfaces or become  
knotted.  
This appliance is for household use only. Do not  
use this appliance for anything other than its  
intended use. Do not use in moving vehicles or  
boats. Do not use outdoors. Misuse may cause  
injury.  
To protect against electric shock do not immerse  
the power cord, power plug or appliance in water  
or any other liquid.  
This appliance is not intended for use by persons  
(including children) with reduced physical, sensory  
or mental capabilities, or lack of experience  
and knowledge, unless they have been given  
supervision or instruction concerning use of  
the appliance by a person responsible for their  
safety.  
The installation of a residual current device (safety  
switch is recommended to provide additional  
safetyprotectionwhenusingelectricalappliances.  
It is advisable that a safety switch with a rated  
residual operating current not exceeding 30mA  
be installed in the electrical circuit supplying the  
appliance. See your electrician for professional  
advice.  
Children should be supervised to ensure that they  
do not play with the appliance.  
It is recommended to regularly inspect the  
appliance. To avoid a hazard do not use the  
appliance if power cord, power plug or appliance  
becomes damaged in any way. Return the entire  
appliance to the nearest authorised Kambrook  
Service Centre for examination and/or repair.  
DO NOT OPERATE THE HOT CuP ON AN INCLINED SuRFACE. DO NOT MOVE THE KETTLE WHILE IT IS SWITCHED ON.  
 
KQK600_HOTCUP_IB_FA.indd  
3
19/6/09 4:00:16 PM  
KNOW YOUR KAMBROOK RAPID BOIL  
1
2
3
7
4
5
6
8
1
6
Illuminated power ON/OFF switch  
Lid release button  
Removable drip tray and cover  
Dispensing spout  
2
7
3
8
Water chamber  
Power base  
4
1.5L capacity  
5
2400 Watt concealed element boils 250ml of  
water in under 60 seconds.  
 
KQK600_HOTCUP_IB_FA.indd  
4
19/6/09 4:00:17 PM  
6. Repeat steps 3, 4 and 5 until the water has  
been emptied from the Hot Cup.  
OPERATING INSTRUCTIONS  
OPERATING YOUR KAMBROOK  
HOT CUP  
Your kettle will only operate when positioned on  
the power base with the ON/OFF switch in the ON  
position. The kettle will automatically switch off  
once the water has boiled.  
BEFORE FIRST USE  
Remove any packaging material and promotional  
labels before using your kettle for the first time.  
Note: The maximum capacity of the Kettle is 1.5L.  
OPERATION OF YOUR KETTLE  
IT IS RECOMMENDED WITH DuE CARE AND ATTENTION PLACED  
ON THE FOLLOWINg PRECAuTIONS bEFORE OPERATINg THE HOT  
CuP.  
1. To fill the kettle with water, remove it from the  
power base and open the lid by pressing the lid  
release button. The lid will automatically open.  
WARNINg: THIS KETTLE DISPENSES 250ML OF HOT WATER  
2. Fill with the desired amount of water. Do not  
operate the kettle without water. Always fill the  
kettle between the minimum and the maximum  
marks on the water window. Too little water will  
result in the kettle switching off.  
CONTINuOuSLy PER OPERATION.  
IT IS NOT POSSIbLE TO INTERRuPT AND STOP THE HOT WATER  
FLOWINg OuT FROM THE DISPENSINg SPOuT ONCE ONE CuP OF  
WATER (250ML) HAS bOILED. THEREFORE, yOu MuST ENSuRE  
THAT A VESSEL/CuP IS CAPAbLE OF HOLDINg A MINIMuM  
OF 280ML CAPACITy AND IS PLACED uNDER THE DISPENSINg  
SPOuT OF THE KETTLE ON THE DRIP TRAy. DO NOT OVERFILL THE  
CuP AS THE WATER IS VERy HOT.  
3. Ensure that the lid is closed and locked firmly into  
place before placing the kettle on the power base.  
Place the kettle firmly onto the power base. Plug  
the power cord into 230/240V power outlet and  
switch ‘ON’.  
THE APPLIANCE SHOuLD ALWAyS bE PLACED ON A FIRM LEVEL  
SuRFACE WHERE NORMAL ACCESS FROM PERSONS (INCLuDINg  
CHILDREN) WITH REDuCED PHySICAL, SENSORy OR MENTAL  
CAPAbILITIES IS RESTRICTED.  
4. Press the ON/OFF switch to the ‘ON’ position.  
The power ‘ON’ light will illuminate.  
Note: In choosing the size of vessel/cup, it is  
recommend the capacity is not less than 280ml,  
make sure the vessel/cup is positioned in place  
before using. Do not overfill the cup.  
IT IS RECOMMENDED THAT A VESSEL/CuP CAPAbLE OF  
ACCOMMODATINg A MINIMuM OF 280ML OF VERy HOT WATER  
IS PLACED uNDER THE DISPENSINg SPOuT AT ALL TIMES  
TO CAPTuRE THE DISPENSED WATER SHOuLD THE uNIT bE  
INADVERTENTLy TuRNED ON.  
5. The kettle will switch off automatically once  
one cup of water (250ml) has boiled.  
6. The hot water will flow out from the spout  
under 60 seconds. Before removing cup, make  
sure the water flow has ceased.  
It is recommended that before the first use to fill  
the kettle to the maximum level with cold tap  
water, carry out several boil cycles discarding the  
water each time from a vessel/cup capable of  
holding a minimum of 280ml capacity. Then, discard  
the water inside the water chamber as following.  
Note: The water flowing out from spout is hot and  
contact with the hot water may result in scalding.  
Therefore, this appliance should not be used  
by children.  
If you want to boil water again, simply press the  
power ON/OFF switch to ‘ON’ position again.  
EMPTYING YOUR RAPID BOIL  
1. After the Hot Cup has completely cooled down,  
unplug it from the mains supply socket.  
If further heating of the kettle is not required,  
switch off at the power outlet, unplug the power  
cord and empty the water from the kettle. Replace  
the kettle onto the power base and close the lid.  
2. Press the lid release button.  
3. Hold your kettle sideways over a sink.  
4. Then, tip the Hot Cup upside down.  
5. Still holding the Hot Cup over the sink, turn it  
the right side up and allow any water to drain  
out of the spout.  
 
KQK600_HOTCUP_IB_FA.indd  
5
19/6/09 4:00:18 PM  
SAFETY BOIL DRY PROTECTION  
The Hot Cup is fitted with a safety device, which  
protects against overheating should the appliance  
be operated with insufficient water. If this occurs  
the Hot Cup will stop heating and the illuminated  
light on the power on/off switch will go out. Switch  
off at the power outlet and allow the kettle to  
cool before refilling. Remove the Hot Cup from the  
power base and add cold water. Return the Hot  
Cup to the power base. The safety device will then  
automatically reset.  
IMPORTANT: IF yOuR HOT CuP WILL NOT bE uSED FOR  
AN ExTENDED PERIOD (E.g. IF yOu ARE ON HOLIDAy), WE  
RECOMMEND THAT yOu FIRST EMPTy IT. FOLLOW THE  
EMPTyINg yOuR RAPID bOIL ON PAgE 5 bEFORE uSINg THE HOT  
CuP AgAIN, CARRy OuT SEVERAL bOIL CyCLES DISCARDINg  
THE WATER EACH TIME. THIS SHOuLD PREVENT ANy bAD  
SMELL OR TASTE FROM WATER THAT MAy HAVE RESIDED IN  
THE uNIT OVER THE ExTENDED PERIOD OF NON uSE.  
NOTE: Never operate the Hot Cup dry - too little  
water will result in the Hot Cup switching “OFF”. Do  
not overfill the Hot Cup - filling above the maximum  
mark on the water window may result in water  
splashing from the kettle.  
NOTE: The Hot Cup must only be used with the  
power base supplied.  
NOTE: Do not remove the Hot Cup from the power  
base during operation. Ensure the Hot Cup has  
switched to ‘OFF’ position after the water flow has  
ceased before removing the vessel/cup.  
CAuTION: THIS APPLIANCE IS DESIgNED FOR THE bOILINg  
OF DRINKINg quALITy WATER ONLy, NEVER uSE IT TO HEAT  
OR bOIL ANy OTHER LIquIDS OR FOODSTuFFS. THE LID  
SHOuLD ALWAyS bE FIRMLy IN PLACE AND LOCKED CLOSED  
bEFORE uSE.  
 
KQK600_HOTCUP_IB_FA.indd  
6
19/6/09 4:00:18 PM  
CARE AND CLEANING  
Always switch off at the power outlet, and then  
unplug the appliance from the power outlet before  
cleaning.  
Note: Ensure the kettle and water have cooled  
down before attempting to clean the kettle.  
REMOvAL OF MINERAL DEPOSITS  
Mineral deposits in tap water may cause the  
interior and water gauge to discolour over time. This  
may be removed by the following way.  
1. Fill the Hot Cup until 23 full with 1 part vinegar  
and 2 parts water. Mix them in a vessel before  
pouring into the water chamber of the Hot Cup.  
Boil and allow to stand overnight.  
2. Empty the solution from the Hot Cup. Fill with  
clean water, bring to boil and discard the water.  
Repeat and the Hot Cup will be ready for use.  
TO CLEAN THE ExTERIOR  
The outside of the Hot Cup may be wiped over with  
a damp cloth and polished with a soft, clean dry  
cloth.  
Empty the drip tray. Wash the drip tray and drip  
tray cover in warm soapy water. Rinse and dry  
thoroughly before placing them back to the power  
base.  
Note: Do not use kettle descaler, chemical, steel  
wool, or abrasive cleaners to clean the inside or  
outside of the Hot Cup.  
STORAGE  
Ensure the kettle is switched off, cleaned and dried  
before storing. Ensure that the lid is closed and  
locked securely into place. Wrap the power cord  
around the cord storage under the power base.  
Stand the kettle upright on the power base. Do not  
store anything on top.  
WARNINg: TO PREVENT DAMAgE TO THE APPLIANCE, DO  
NOT uSE ALKALINE CLEANINg AgENTS WHEN CLEANINg. uSE A  
SOFT CLOTH AND MILD DETERgENT.  
WARNINg: NEVER IMMERSE THE HOT CuP bASE, SWITCH  
AREA, POWER bASE OR POWER SuPPLy CORD IN WATER, OR  
ALLOW MOISTuRE TO COME IN CONTACT WITH THESE PARTS.  
 
KQK600_HOTCUP_IB_FA.indd  
7
19/6/09 4:00:18 PM  
KAMBROOK 12 MONTH REPLACEMENT WARRANTY  
Kambrook warrants the purchaser against defects in workmanship and material for a period of 12 months  
from the date of purchase (3 months commercial use).  
Guarantee and purchase receipt for this product are to be retained as proof of purchase and must be  
presented if making a claim under the Kambrook guarantee.  
Kambrook reserves the right to replace or repair the appliance within the warranty period.  
Warranty does not apply to any defect, deterioration, loss, injury or damage occasioned by, or as a result  
of the misuse or abuse, negligent handling or if the product has not been used in accordance with the  
instructions. The guarantee excludes breakages and consumable items such as kneading blades.  
This warranty is void if there is evidence of the product being tampered with by unauthorised persons.  
If the product includes one or a number of accessories only the defective accessory or product will be  
replaced. In the event of Kambrook choosing to replace the appliance, the guarantee will expire at the  
original date, i.e. 12 months from the original date of purchase.  
In Australia, this KAMBROOK Guarantee is additional to the conditions and guarantees which are mandatory  
as implied by the Trade Practises Act 1974 and State and Territory legislation.  
For service, spare parts or product information in Australia, please call KAMBROOK on the Customer  
Service Line; 1300 139 798.  
For service, spare parts or product information in New Zealand, please call KAMBROOK on the Customer  
Service Line; 0800 273 845 or 09 271 3980.  
If claiming this guarantee the product must be returned freight prepaid.  
KAMBROOK 12 MONTH REPLACEMENT WARRANTY  
Attach a copy of the purchase receipt here.  
YOUR PURCHASE RECORD (Please complete)  
DATE OF PURCHASE .......................................................  
MODEL NUMBER .............................................................  
SERIAL NUMBER .............................................................  
(Please don’t return purchase record  
PURCHASED FROM .........................................................  
until you are making a claim)  
Kambrook - New Zealand  
Private Bag 94411  
Botany, Manukau  
Auckland 2163  
New Zealand  
Customer Service Line/Spare Parts 0800 273 845  
or 09 271 3980  
Kambrook - Australia  
Building 2, Port Air Industrial Estate  
1A Hale Street  
Botany NSW 2019  
Australia  
Customer Service Line 1300 139 798  
Customer Service Fax 1800 621 337  
Customer Service Fax 0800 288 513  
Due to continual improvement in design or otherwise, the product you purchase may differ slightly from the illustration in this book. Issue 1/09  
 
KQK600_HOTCUP_IB_FA.indd 12  
19/6/09 4:00:12 PM  

Invacare Mobility Aid Comfort Mate Extra Comfort Mate Extra Base User Manual
JVC Battery Charger AA V15U User Manual
JVC Flat Panel Television 0504TNH II IM User Manual
Kenmore Washer Dryer 27 69 cm Wide LAUNDRY CENTER Washer Electric Dryer P N 134809700A User Manual
King Canada Drill KC 50 User Manual
KitchenAid Double Oven KEBS277SSS03 User Manual
KitchenAid Mixer 6397dZw608 User Manual
Kodak Digital Camera CD44 User Manual
Kompernass Microwave Oven KH1167 User Manual
Konica Minolta All in One Printer FM01FD02B User Manual