Triple Bay Conventional Gas Grill Cooktop
PRODUCT MODEL NUMBERS
JGD8348CD
GAS REQUIREMENTS
Gas supply: The installation of this appliance
The maximum gas supply pressure for the
Make the gas connection to the inlet of the
appliance pressure regulator on this appliance
with a 1/2" male pipe thread. Use an approved
pipe joint compound resistant to the action of LP
gas at pipe connections.
must conform with local codes, or in the absence appliance pressure regulator supplied on this
of local codes, with the latest edition of the
National Fuel Gas Code ANSI Z223.1 USA or
current CAN/CGA-B149 INSTALLATION CODE.
appliance is 14" W.C. The test pressure for
checking this appliance pressure regulator must
be at least 6" W.C. for Natural Gas, and at least
11" W.C. for LP. It is shipped from the factory set
for Natural Gas at 5" W.C.
This appliance was adjusted at the factory for use
with natural gas. If, at any time, this appliance is
to be used with a different type of gas, all of the
conversion adjustments described in the
installation instructions must be made by a
qualified service technician before attempting to
operate the cooktop on that gas.
Electrical: See page 2.
Install a manual shutoff valve in an accessible
location in the gas line external to this appliance
for the purpose of turning on or shutting off gas
to the appliance.
PRODUCT DIMENSIONS
Dimension “A” - provide 2" min. (5.1 cm) cabinet clearance to motor for
cooling purpose.
Side Clearance: Grills installed near a side wall must allow a minimum
clearance of 8" (20.3 cm).
NOTE: Where possible, 6" (15.5 cm) is recommended for motor/blower
service.
Access must be provided to remove and empty grease container.
This appliance is designed to always be vented outdoors.
Page 1 of 3
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 8101P620-60
09-25-08
Triple Bay Conventional Gas Grill Cooktop
PRODUCT MODEL NUMBERS
JGD8348CD
INSTALLATION OF CABINETRY OVER YOUR GRILL
Minimum horizontal clearance between the edge of the appliance and
combustible construction extending from the cooking surface to 18"
(45.7 cm) above the cooking surface is:
Avoid use of cabinets above cooktop for storage space to eliminate
associated potential hazards such as reaching over open flames.
Dotted lines indicate range hood construction.
1-3/4" (4.5 cm) at rear
8" (20.3 cm) at sides
NOTE: This is not the
* To eliminate the risk of burns or fire by
reaching over heated surface units, cabinet
storage space located above the surface units
should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing
a range hood that projects horizontally a
minimum of 5" (12.7 cm) beyond the bottom of
the cabinets.
recommended clearance,
(4
but minimum allowable
clearance.
* A = 30" (76.2 cm)
minimum vertical
Cabinets Above Cooking Top
clearance between
MIN. CLEARANCE
cooking surface
Maximum depth of cabinets installed above cooking top is 13" (33 cm).
and construction above the appliance.
B = 13" (33.0 cm) maximum depth of cabinets installed above cooking
top.
MINIMUM SPACING REQUIREMENTS
For installing a TripleBay Downdraft Cooktop in combination with another Downdraft Cooktop, the minimum spacing between adjacent units must be
provided, as shown, for satisfactory performance.
4-3/8"
PROSTYLE
COOKTOP
ANY DOWNDRAFT
COOKTOP
(11.1 cm)
(Single, Double or
Triple Bay)
18"
(45.7 cm)
PROSTYLE
COOKTOP
ANY
DOUBLE BAY
4-3/8"
(11.1 cm)
18"
(45.7 cm)
PROSTYLE
COOKTOP
ANY
SINGLE BAY
16-1/8"
(41 cm)
Page 3 of 3
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 8101P620-60
09-25-08
|