Jasco Universal Remote RM84930 User Manual

RM84930  
Universal Remote  
Instruction Manual  
 
Setup  
Battery Installation  
1. On the back of the remote, push down on the  
tab and lift the cover off.  
ꢀ. Match the batteries to the + and - marks inside  
the battery case, then insert ꢀ AAA Alkaline  
batteries.  
3. Press the battery cover back into place.  
Battery Saver  
Your remote automatically turns off if the buttons  
are depressed more than 30 seconds. This will  
save your batteries should your remote get stuck in  
a place where the buttons remain depressed (e.g.,  
between the sofa cushions).  
Code Saver  
You will have up to 10 minutes to change the  
batteries in your remote without losing codes you  
have programmed. However, do not press any  
buttons until batteries are installed in the remote.  
If buttons are pressed without batteries in the  
remote, all codes will be lost.  
SETUP  
Code Setup  
The SETUP button is used to setup the remote.  
You can either setup the remote using the code  
tables (on separate sheet), or you can search  
through the library of codes until you find a code  
that works for your product. Please refer to “ Code  
Search” on page 8 for more information on using  
the code search feature to learn how to search  
through the library of codes for your products.  
NOTE: You can store any kind of code under any  
mode (except TV). I.E. you can store a VCR code  
under the CBL/SAT button, or a Cable code under  
the DVD/AUX button, etc. However, you can only  
store TV codes under the TV button.  
3
 
Button Functions  
Some buttons on the remote might have functions that  
are referred to by different names on the device you  
are controlling. E.G. PREV.CH may be called RECALL,  
or ENTER may be called DISPLAY. These differences  
depend on the brand and model of your product. Also,  
this remote can only operate features that exist on your  
product. E.G., your product must have PREV.CH ability  
for the PREV.CH button to operate this feature.  
TV, CBL/SAT, VCR, DVD/  
AUX Selects product to  
be operated.  
Red Indicator  
Lights when any  
button is pressed.  
PREV.CH Returns to  
the previously selected  
channel.  
INFO Shows the date  
and time if your TV or  
VCR has that feature.  
Works the same way as  
a Display button.  
MENU Brings up device  
Main Menu. Use Chan  
and Vol buttons as cursor  
buttons and Mute as Okay.  
Press TV to Exit.  
ENTER  
Used to complete chan-  
nels selection for some  
brands of TV. Also used  
to complete the code  
entry process.  
RECORD, PLAY, STOP,  
REW, FF, PAUSE VCR  
control buttons operate  
your VCR even when the  
remote is set to operate  
the TV. Also operates DVD  
Scan -/+. Note the VCR  
buttons also control DVD  
when in DVD Mode.  
4
 
Button Functions, cont.  
SETUP Used to setup  
ON-OFF Turns  
the remote, and for code product On or Off.  
search function.  
Backlight Lights up the  
buttons on the remote  
when pressed. See page  
10 for more details.  
MUTE Turns off the  
TV sound while the  
picture remains.  
VOLUME UP/DOWN  
Changes the volume  
level of the product,  
normally the TV.  
CHANNEL Up/Down  
Changes the channels.  
The Channel buttons  
also control DVD SKIP  
functions.  
INPUT Selects the  
video inputs of your  
TV if equipped with  
that feature.  
0-9  
Enter numbers for direct  
channel selection. Some  
products require ENTER to  
be pressed after channel  
selection.  
TV/VCR Operates the same  
as the TV/VCR or antenna  
keys on your original remotes.  
Note: The REC button must be pressed TWICE to record  
from your VCR. For some brands of VCRs, you might  
need to press the REC button once, then press it again  
for three seconds.  
 
Menu Operation  
The Menu button puts the remote in and out of  
Menu Mode. Pressing Menu brings up your  
device Menu. While in Menu mode the remote’s  
red indicator light blinks continuously. The remote  
will exit Menu Mode after ꢀ0 seconds if no keys are  
pressed.  
When in Menu Mode, the Menu, Channel, Volume,  
Mute and Device keys operate as follows:  
MENU Enters Menu mode.  
CHANNEL UP/DOWN Cursor Up/Down for Menu  
navigation.  
VOLUME UP/DOWN Cursor Right/Left for Menu  
navigation.  
MUTE (OK) command for Menu selections.  
Press TV or any other Device key to Exit, Clear,  
or Quit the Device Menu and return the remote to  
normal operation (red indicator will turn off).  
For certain RCA, GE, and ProScan devices,  
pushing the MENU button selects the highlighted  
item. The numeric buttons may also be used to  
select the MENU choice.  
Note: Some functions in some brands might not be  
fully supported.  
6
 
Direct Code Entry  
SETUP  
1. Press and hold the SETUP button until  
the red indicator stays on, then release  
the SETUP button.  
TV  
ꢀ. Press and release the desired device  
button (TV, VCR, etc.). The red indicator  
blinks, then stays lit.  
3. Enter the 3 digit code  
1
4
7
2
5
8
3
6
9
from the code tables  
(on separate sheet).  
Note: after a valid  
code entry, the red  
indicator turns off. For  
an invalid code, the  
red indicator flashes.  
/.ꢀ/&&  
4. With your device on, press ON/OFF.  
If the device turns off, no further  
programming is required. Note: If  
some buttons do not operate your  
equipment, try one of the other  
codes for your brand.  
Write your codes down here for easy  
reference later.  
Device  
Device stored Code  
TV  
TV  
CBL/SAT  
VCR  
DVD/AUX  
7
 
Code Search  
If your device does not respond after you have  
tried all the codes for your brand, or if your brand is  
not listed, try searching for your code by following  
these steps.  
1. Manually turn on the device (TV, VCR, etc.) to  
be controlled.  
ꢀ. Press and hold the SETUP button  
SETUP  
until the red indicator stays on, then  
release the SETUP button.  
3. Press and quickly release the desired  
TV  
device button (TV, VCR, etc.). The red  
indicator blinks off once.  
/.ꢀ/&&  
4. Press the ON-OFF button repeatedly  
(up to 300 times) until the device  
to be controlled turns off. The red  
indicator blinks off with each button  
press.  
ENTER  
ꢁ. Press and release ENTER to install  
the code.  
Most users will store VCR codes under the VCR button,  
Cable codes under CABLE, etc. If (for example) you  
want to store a VCR code under DVD/AUX, first follow  
the procedure for Direct Code Entry (previous page) and  
press DVD/AUX in step ꢀ of Direct Code Entry, then  
enter ANY VCR code in step 3 of Direct Code Entry.  
Then follow the steps above for Code Search.  
Note: Code Search starts from the currently stored  
three digit number under that mode. Sometimes the first  
code that “works” with your device may only allow limited  
functionality (e.g. the MENU button might not work).  
There may be a code that performs more functions.  
Continue the code search process until the best code  
is found.  
8
 
Using Your Remote  
Code Identification  
The Code Identification Feature allows you to  
identify the three digit library code stored under  
your device button. For example, if you want to find  
out what three digit code is stored under your TV  
device button, follow the six steps below:  
SETUP  
1. Press and hold the SETUP button until  
the red indicator stays on. Release the  
SETUP button.  
TV  
ꢀ. Press and release the desired  
device button (TV, VCR, etc.). The  
red indicator blinks, then stays lit.  
SETUP  
3. Press and release the SETUP button.  
The red indicator blinks once and  
remains lit.  
4. To nd the first digit  
for the code stored  
under the device  
1
4
7
2
5
8
3
6
9
button pressed in step  
ꢀ, press each numeric  
button from 0-9 in  
turn. The number that  
causes the indicator  
light to blink is the first  
digit in your code.  
5. To nd the second digit, repeat step 4.  
6. Repeat step 4 again to find the third digit. This  
time the red indicator turns off and stays off.  
9
 
Using Your Remote, cont.  
Controlling Devices with Separate  
Power On and Off Buttons  
Some GE, RCA and ProScan models require  
you to press the device button for more than one  
second to turn the device on and the ON•OFF  
button to turn the device off.  
Controlling Combo Devices  
Some Combo devices (e.g. TV/VCR, TV/DVD,  
DVD/VCR, etc.) will require you to set up two  
different Mode buttons to control both parts of the  
Combo device. For example, if you have a TV/  
DVD Combo, you might need to set up one code  
under the TV button to control the TV part AND a  
separate code (under any other Mode button) to  
control the DVD part.  
VCR/DVD Punch-Through  
This remote allows the 6 VCR transport buttons  
(i.e. PLAY, PAUSE, STOP, FF, REWIND, and  
REC) to Punch-Through control from any Mode  
programmed with TV, SAT or Cable codes to the  
last VCR, or DVD programmed Mode you used.  
This feature will not operate if the programmed  
TV, SAT or Cable code has its own VCR transport  
button control e.g. a TV Combo, SAT/PVR, etc.  
Backlight Button  
Backlighting is activated when you press the  
Backlight button. Backlight illumination occurs  
for five seconds after the Backlight button has  
been pressed. Any further key-presses within five  
seconds will continue to reset the five second time-  
out period. I.E., illumination always remains on for  
five seconds after the last keypress. Once timed  
out, the Backlighting will not reactivate until the  
Backlight button is pressed again.  
10  
 
Using Your Remote, cont.  
Volume/Mute Control and  
Punch-Through  
This remote lets you select which device Mode  
controls your Volume/Mute buttons. The remote is  
initially set for all device Modes to use their own  
Volume/Mute control if present. If the programmed  
code has no Volume/Mute operation of its own  
then those buttons will punch-through control to  
the TV Mode device without needing to change to  
TV Mode.  
Any Mode chosen for Volume/Mute control  
MUST have its own Volume/Mute function or  
the Volume/Mute buttons will do nothing.  
Setting ALL Volume/Mute Control to  
any one Mode  
This routine can set all Modes to “punch-through”  
to any one chosen Mode for Volume/Mute button  
control without the needing to change to that  
SETUP  
Mode.  
1. Press and hold the SETUP button until  
the red indicator turns on, then release  
MUTE  
the button.  
ꢀ. Press and hold the MUTE button until the  
red indicator blinks off, then release the  
button.  
3. Press and release the desired Mode button  
TV  
(TV, VCR, etc.) for Volume/Mute control,  
the red indicator blinks then stays on.  
4. Press and release the MUTE button  
MUTE  
and the red indicator turns off. The  
red indicator will blink rapidly for three  
seconds if the Mode you have selected  
has no Volume/Mute control. All other  
Modes will now punch-through to your  
chosen Mode for Volume/Mute control.  
11  
 
Using Your Remote, cont.  
Setting any Mode to use its own  
Volume/Mute Control  
This routine can set any Mode to use only its own  
Volume/Mute control. Note - If your chosen Mode  
has no Volume/Mute functions of its own then the  
Volume/Mute buttons will do nothing.  
SETUP  
1. Press and hold the SETUP button until  
the red indicator turns on, then release  
the button.  
ꢀ. Press and hold the MUTE button until  
the red indicator blinks off, then release  
the button.  
MUTE  
3. Press and release the desired Mode  
button (TV, VCR, etc.), the red indicator  
blinks then stays on.  
TV  
4. Press and release the VOLUME-  
(Down) button, the red indicator blinks  
then stays on.  
ꢁ. Press and release the MUTE button and  
the red indicator turns off.  
Your chosen Mode will now use its  
own Volume/Mute control.  
`
MUTE  
`
1ꢀ  
 
Troubleshooting  
Remote does not operate your product.  
Press the device button of the product you want  
to control.  
Program the remote with a new code.  
Install new batteries. (You might have to  
reprogram your remote after installing new  
batteries.)  
Remote may not be compatible with your  
product.  
Remote does not operate some features of  
your product.  
Sometimes a particular code might operate  
some features but not all. Try programing  
remote with a new code.  
Remote may not be able to operate all features  
of your product or button names might be  
different than your product.  
Red Indicator blinks after you program a  
product code.  
Remote did not accept the code.  
Try to program the code again or try a different  
code.  
Lost Your Codes?  
Enclosed with this remote is a sticker on which  
you should write the codes for each device you  
programmed. Apply the sticker to the back of  
the remote or somewhere convenient for future  
reference.  
Also on the sticker is our website address which,  
should you lose your codes or programming  
instructions, you can find available on our website:  
13  
 
Notes  
14  
 
90 Day Limited Warranty  
Jasco Products Company warrants this product  
to be free from manufacturing defects for a period  
of ninety days from the original date of consumer  
purchase. This warranty is limited to the repair  
or replacement of this product only and does not  
extend to consequential or incidental damage to  
other products that may be used with this unit.  
This warranty is in lieu of all other warranties  
express or implied. Some states do not allow  
limitations on how long an implied warranty lasts  
or permit the exclusion or limitation of incidental or  
consequential damages, so the above limitations  
may not apply to you. This warranty gives you  
specific rights, and you may also have other rights  
which vary from state to state. If unit should prove  
defective within the warranty period, return prepaid  
with dated proof of purchase to:  
Jasco Products Company  
311 N.W. 1ꢀꢀnd  
Oklahoma City, OK 73114  
1ꢁ  
 
RM84930  
Universal Remote  
Instruction Manual  
Jasco Products Company  
311 N.W. 1ꢀꢀnd  
Oklahoma City, OK 73114  
Made in China  
RMꢀ4931-  
 

Indesit Refrigerator IN TS 1610 UK User Manual
Indesit Washer IWC 6103 User Manual
Ingersoll Rand Grinder DG15W A User Manual
JBL Home Theater System ES100 User Manual
JL Audio Car Speaker 12WX User Manual
JVC Digital Camera GC A70 User Manual
Kambrook Kitchen Utensil EK9B User Manual
KitchenAid Oven KCO1005 User Manual
KitchenAid Ventilation Hood KHLU182MSS1 User Manual
Kodak Digital Camera CX6200 User Manual