Jabra Headphones 100 91030000 02 User Manual

NON-BT  
IMPORTANT  
READ THIS FIRST  
TM  
JABRA FreeSpeak QUICK START GUIDE  
For Nextel Phones  
Model #:100-91030000-02  
Model #:100-91130000-02  
Model #:100-91430000-02  
Headset Indicator Light  
(Blue LED)  
Multi-Function Button  
MiniGel™  
Volume Control Button  
BEFORE USING YOUR HEADSET  
Charge FreeSpeak – FreeSpeak is rechargeable and must be charged before use.  
1. Insert the headset fully into its multi-adapter.  
2. Plug one end of the AC power adapter into the multi-adapter and the other end into an  
electrical wall outlet.  
3. Charge your headset for approximately 2 hours or until both blue indicator lights go out.  
Important: Blue indicator lights on the headset and multi-adapter will both be on while  
charging and will turn off when charging is complete.  
Connect multi-adapter to phone  
• For phones with standard 2.5mm headset jacks: Plug the multi-adapter’s connector into the  
2.5mm headset jack on your phone.  
Location of phone’s headset  
jack may vary.  
For i2000plus, i2000, i1000plus, i1000, r750plus, i700plus, i550plus, i500plus and i500  
phones: Plug the audio adapter (sold separately) into your phone. Then plug the multi-  
adapter’s connector into the audio adapter.  
 
To answer and end calls with only the headset:  
Some phones enable you to answer or end a call by pressing and releasing  
without having  
to touch the phone. For all Nextel phone models (except the i1000), the phone’s Automatic  
Answer feature needs to be activated for this headset feature to work.  
For the BlackBerry 6510, FreeSpeak's Anwer/End feature has to be turned on.  
To turn on FreeSpeak's Answer/End feature:  
1) Ensure that the AC power adapter is not connected.  
2) Put the headset in the multi-adapter.  
3) Use the stylus to press the stylus switch for about 12 seconds.  
4) You will then see a number of blinks (long flashes) on the multi-adapter indicator  
light which tell you whether this feature is enabled or disabled according to the  
following table:  
Answer/End Feature  
Comments  
Number of Blinks  
4
5
Enabled  
Disabled  
--  
Default Setting  
5) Repeat steps 1-4 to switch between enabled and disabled settings.  
If you are enabling Answer/End feature for the first time, you should test answering and ending  
calls to ensure that your phone supports this feature.  
For more information, see “Enhanced Features” at www.jabra.com/fscs.  
Calls can be ended by the headset only by waiting for the line to disconnect.  
STATUS INDICATORS  
What you see  
What you hear  
Status  
Flashes every second  
When Active Mode  
starts: quick series  
Active Mode  
• Call in progress  
of TWO tones – low • Up to 4 hours of talk time  
to high pitch  
When Standby  
Mode starts: quick  
series of TWO  
tones – high to low  
pitch  
Standby Mode  
• Waiting for call  
• Up to 100 hours of standby time with  
mheadset in multi-adapter  
Flashes every 3  
seconds  
 
TIPS & SOLUTIONS  
To prolong battery life:  
• After you’ve ended a call using your phone’s keypad, always remember to place the  
headset in Standby mode by pressing and releasing  
when not in use.  
• Dock the headset firmly in its multi-adapter when not in use.  
If you press and release  
and the headset stays in Standby mode:  
If FreeSpeak becomes unpaired, it will not respond to the  
occur when you first receive the product or when you hold the  
the product.  
button. In rare cases, this may  
button too long while using  
To pair” the headset with the multi-adapter:  
1. Ensure headset is off.  
2. Press  
until you see a solid blue light on the headset, then release.  
3. Use the stylus to press down on the  
stylus switch until you see a solid blue  
light on the multi-adapter, then  
release.  
Multi-adapter  
Important: Once pairing is complete,  
lights on both the headset and multi-  
adapter will begin flashing (Standby  
mode).  
Stylus  
Switch  
Stylus  
If you hear an echo of your voice – You may need to adjust  
microphone levels.  
To reduce the echo:  
Flashes or  
Beeps  
Microphone Level  
High (default)  
Medium  
1
1. Lower the volume of your phone and headset.  
2. If echo persists, put FreeSpeak in Active mode.  
2
3
Low  
3. Use the stylus to press down on the stylus switch (as shown above) until you see a solid  
c blue light on the multi-adapter. Continue to press down until you see/hear 1, 2, or 3  
z flashes/beeps, then release. The last number of flashes/beeps corresponds to the final  
c setting.  
4. Repeat step 3 to cycle between different microphone levels.  
 
If the headset is not responding or the light will not turn off after pairing - You may need to  
reset your headset.  
1. Plug one end of the AC power adapter into the multi-adapter and the other end into an  
electrical wall outlet.  
2. Insert the headset into the multi-adapter for about 3 seconds, then remove.  
To improve audio clarity:  
Stay within 30 feet (10 meters) of your multi-adapter. In general, you will get the best perform-  
ance when there are no obstructions (including parts of the body) between your headset and the  
multi-adapter.  
Need more help?  
1. Consult the complete User’s Guide  
2. Web: www.jabra.com/fscs (for the latest support info)  
3. Telephone: (858) 622-9955, Monday to Friday 8am to 5pm PST  
(800) EAR-2230 (USA and Canada)  
 

InFocus Personal Computer Secure Digital SD Memory Stick User Manual
InFocus Projector IN3128HD User Manual
IOGear Headphones GBHFK201W6 User Manual
iOptron Camcorder Accessories 8600 User Manual
Jaguar Automobile S Type User Manual
JVC DVD Player XV 515GD User Manual
JVC DVD VCR Combo DR MV4SUJ User Manual
KitchenAid Dishwasher KUDE48FXBL0 User Manual
KitchenAid Mixer KSM500PSER0 User Manual
Knoll Speaker OUT650 User Manual