CAUTION:
To prevent malfunction of the player
• There are no user-serviceable parts inside. If
anything goes wrong, unplug the power cord and
consult your dealer.
• Do not insert any metallic objects, such as wires,
hairpins, coins, etc. into the player.
• Do not block the vents. Blocking the vents may
damage the player.
Connections
Before making connections:
• Do not connect the AC power cord until all other connections have been made.
• Connect VIDEO OUT of the player directly to the video input of your TV. Connecting VIDEO OUT of the
player to a TV via a VCR/an integrated TV/Video system may cause a monitor problem.
DVD PLAYER
XV-N320B
XV-N322S
Warnings, Cautions and Others
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as
lighted candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing
the disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
Connecting to a TV with component jacks
Connecting to a stereo audio amplifier (receiver)
PB
RIGHT
Y
PB
RIGHT
Y
XIAL
LEFT
VIDEO
PR
LEFT
TREAM
L OUT
AUDIO OUT
VIDEO OUT
INSTRUCTIONS
Connecting to a TV with SCART connector
VO
PR
AUDIO OUT
VEO OUT
To analog
To analog audio input
To clean the cabinet
®
NOTE
audio input
• Use a soft cloth. Follow the relevant instructions on
the use of chemically-coated cloths.
• Do not use benzene, thinner or other organic solvents
and disinfectants. These may cause deformation or
discoloring.
TV
The VIDEO jack, AV OUT terminal, and
component (Y,PB, PR) jacks cannot be
used at the same time.
SCART cable
(not supplied)
Connecting to a digital audio device
V I D E O
IN
To enjoy high-quality surround sound, connect the
DIGITAL OUT (COAXIAL) jack to a Dolby Digital or DTS
decoder or an amplifier with a built-in decoder.
IN
Caution: Proper Ventilation
To avoid risk of electric shock and fire and to protect
from damage, locate the apparatus as follows:
To component
video input
S-VIDEO
VIDEO
PB
GNT0059-004A[EK]
0105MOC-MW-SC
©2005 Victor Company of Japan, Limited
RIGHT
Y
COAXIAL
To switch the scanning mode between Progressive and
Interlace, press and hold VFP-I/P on the remote control
for a few seconds.
Front:
No obstructions and open spacing.
EN
Playable discs
• DVD VIDEO, Audio CD, Video CD, SVCD
Sides: No obstructions in 3 cm from the sides.
LEFT
PCM/STREAM
DIGITAL OUT
L
EF
T
VIDEO
PR
Top:
Back:
No obstructions in 5 cm from the top.
No obstructions in 15 cm from the back.
A
AUDIO OUT
VIDEO OUT
UDIO
Region code of DVD VIDEO
R
IGH
T
NOTES
To analog
audio input
This player can play back DVD VIDEO discs
whose region code numbers include “2.”
Examples of playable DVD VIDEO discs:
Bottom: No obstructions, place on the level surface.
• Connect to a TV with composite jacks and set
[CONNECTIONS] to [VIDEO COMPONENT] before
connecting with component jacks. (See
“CONNECTIONS” in “Initial settings.”)
• Connect “Y” to “Y,”“PB” to “PB(CB),”“PR” to “PR(CR)”
correctly.
V I D E O
Spacing 15 cm or more
• DVD-R/-RW written in the DVD VIDEO format
• CD-R/RW written in the SVCD, Video CD or Audio CD
format
• CD-R/RW written in MP3/JPEG in accordance with
the “ISO 9660” format
XV-N320B/XV-N322S
AV OUT
1 2
3 4
1 2 3
4 5 6
To digital audio input
Front
ALL
2 5
2
The player
Wall or
obstructions
NOTES
• The VIDEO jack, AV OUT terminal, and component
(Y,PB, PR) jacks cannot be used at the same time.
The player’s region code is printed on the rear of
the player
Note of Color system format
This player accommodates the PAL system, and
also can play back discs recorded with NTSC
system. (NTSC video signals are converted to an
PAL signal and output.)
• Depending on the disc, no signal may be outputted
from the DIGITAL OUT. Make an analog connection
in this case.
• Set [DIGITAL AUDIO OUTPUT] in the [AUDIO]
preference display correctly according to the
connected digital audio equipment. (See “DIGITAL
AUDIO OUTPUT” in “Initial settings.”)
Supported Digital audio formats:
Linear PCM, MPEG Multichannel, Dolby Digital, DTS (Digital
Theater Systems)*
Stand height
5 cm or more
Floor
About the scanning mode indicator
[PICTURE SOURCE] of
the PICTURE menu
Source type of DVD VIDEO
NOTES
Connecting to a TV with composite jacks
Film source
[DDP]
Video source
[P]
CAUTION
• If a disc gets dirty, scratched or warped, or due to the
disc characteristics or recording conditions, the
player may not be able to play back such discs.
• The player can play back audio signals recorded in
MIX-MODE CD, CD-G, CD-EXTRA and CD TEXT.
• With some discs, operations may not be possible.
* To play back DTS-encoded DVD VIDEO or DTS-
encoded Audio CD discs correctly, connect the
player to an amplifier with a built-in DTS decoder.
Otherwise, playback sound will be distorted.
AUTO
FILM
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
TV
Precautions
NOTES
[DDP]
[DDP]
Notes on the power cord
• If your TV has a monaural audio input
instead of stereo, use an optional audio
cable which converts stereo audio
output to monaural.
VIDEO(NORMAL)/
(ACTIVE)
[P]
[P]
Supplied accessories
IN
• When you are away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet. A
small amount of power (1.0 W) is always consumed while
the power cord is connected to the wall outlet.
• When unplugging the player from the wall outlet,
always pull the plug, not the power cord.
• Do not handle the power cord with wet hands!
• Disconnect the power cord before cleaning the
player or moving the player.
• Do not alter, twist or pull the power cord, or put
anything heavy on it, which may cause fire, electric
shock, or other accidents.
• If the cord is damaged, consult a dealer and have the
power cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the player in moist or dusty places.
• If water gets inside the player, turn off the power and
remove the plug from the wall outlet, then consult
your dealer. Using the player in this state may cause
a fire or electrical shock.
• Do not expose the player to direct sunlight or place it
near a heating device.
Notes on installation
If anything is missing, consult your dealer
immediately.
VIDEO
NOTE
Caution ––
Disconnect the mains plug to shut the power off
completely. The STANDBY/ON button in any
STANDBY/ON button!
Some progressive TV and High-Definition TV sets are
not fully compatible with the player. To check the
compatibility of your TV, contact your local JVC
customer service center.
• Remote control (x 1)
LEF
T
• The VIDEO jack, AV OUT terminal, and
component (Y,PB, PR) jacks cannot be
used at the same time.
• R6(SUM-3)/AA(15F) battery (x 2)
AU
DIO
RIG
position does not disconnect the mains line. The power
can be remote controlled.
H
T
Unplayable discs
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
If you try to play back discs listed below, noise may be
generated and causes damage to speakers.
• DVD-RW written in the VR format
• DVD-ROM, DVD-RAM, DVD AUDIO, CD-ROM,
PHOTO CD, SACD
COAXIAL
2. CAUTION: Do not open the top cover. There are no
user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when
open and interlock failed or defeated. Avoid direct
exposure to beam.
PR
PCM/STREAM
DIGITAL OUT
Yellow
RIGHT
VID
LEFT
VDEO OPUBT
• Unfinalized discs
Audio/video cable
(not supplied)
AUDIO OUT
• Discs of irregular shape or discs with tape, seals or
paste on either the label side or playback side.
Playing back these discs may damage the player.
The player
4. REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED INSIDE THE UNIT.
White
The Non-DVD side of a “DualDisc” does not comply with
the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
Red
• Select a place which is level, dry and neither too hot
nor too cold between 5˚C and 35˚C.
• Leave sufficient distance between the player and the TV.
• Do not install the player in a place subject to vibrations.
• Do not put heavy objects on the player.
1
2
3
4
Turning on the power
Initial setup
Basic Operations
Advanced Operations
When you turn on the player for the first time after
purchase, the following message appears on the TV
screen.
Changing the language, sound
Changing the picture tone (VFP)
Turning on and off the player
Inserting the AC power plug
Changing the display window
contents
and scene angle
After all other connections have been made, insert the
AC power plug to the wall outlet firmly.
Insert a disc
The VFP (Video Fine Processor)
function allows you to adjust the
picture character according to the
type of programming, picture tone or
personal preferences.
STANDBY/ON
OPEN/
CLOSE
1 Press the button.
Each time you press DISPLAY,
the display window contents
changes.
Open/close the disc tray
Basic playback
EXECUTE DVD PLAYER SETUP? - BASIC PICTURE/AUDIO
SETTING
YES - PRESS ENTER NO - PRESS CANCEL
1 Press 0 to open the disc tray.
STANDBY/ON
OPEN/
CLOSE
2 Press the button repeatedly or
2 Place a disc in the disc tray.
• To insert an 8-cm disc, place it in the inner
recess.
3 Press 0 to close the disc tray.
+
–
SLOW
DISPLAY ON SCREEN
Turning on and off the player
Installing the batteries in the remote control
Open the compartment cover, and place the two
supplied R6(SUM-3)/AA(15F) batteries in the remote
control according to the polarity markings (“+” and “–”)
inside the compartment. Then replace the cover.
5/∞ to select the desired item.
3 Press ENTER to finish the
setting.
+
–
SLOW
DISPLAY ON SCREEN
TOP
MENU
THUMBNAIL/
LIST
Before enjoying this player, make the initial settings as
follows:
Buttons To do
1 Press VFP-I/P.
TOP
MENU
THUMBNAIL/
LIST
Locating the beginning of a scene
or song
2 Press 2/3 to select the desired
Buttons
To do
3*
7
Start/resume normal Playback
ENTER
1 Press ENTER.
preset.
You can select a title/chapter/
track directly and start playback.
For DVD Video:
(While stopped) select title.
(While playing back) select
chapter.
ENTER
AUDIO
For DVD Video:
select audio languages.
For SVCD/VCD:
select the audio
channel.
Stop
DVD PLAYER SETUP
MENU
SET UP
NEXT
Selected
Preset
• When RESUME is ON or DISC
RESUME, this player
memorizes the position on the
disc where you interrupted
playback.
USER 1
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ENGLISH
ENGLISH
ENGLISH
PREVIOUS SELECT
MENU
SET UP
NEXT
GAMMA
MID
PREVIOUS SELECT
BRIGHTNESS
CONTRAST
+
4
CLEAR
+10
ON SCREEN LANGUAGE
ENGLISH
CLEAR
ENGLISH
SUBTITLE select the subtitle.
ANGLE select the view-angle.
SATURATION +10
FRENCH
GERMAN
1
4
2
5
8
0
3
6
For SVCD/VCD/CD:
Select track.
– To resume playback, press 3.
– To stop playback completely,
press 7 again.
TINT
+10
1
4
2
5
8
0
3
6
SHARPNESS
Y DELAY
LOW
2 Press 5/∞ to select the on-screen language for
To select 5: press 5.
+
2
7
9
the preference displays, etc., then press ENTER.
To select 23: press 2, then 3.
To select 40: press 4, then 0.
• If you press TITLE/GROUP
before entering the number, you
can select the title instead of the
chapter.
8*
Pause
CANCEL
RETURN
7
9
Parameter
Changing the Sound Field
• Each time you press the button,
the still picture advances to the
next frame.
DVD PLAYER SETUP
CANCEL
RETURN
NORMAL For watching TV in a
TITLE/
GROUP
SOUND
EFFECT
Each time you press SOUND
EFFECT, the Sound Effect mode
changes.
• As the value becomes bigger, the
Sound Effect works stronger.
MONITOR TYPE
PICTURE SOURCE
SCREEN SAVER
CONNECTIONS
BACKGROUND
4:3 L.B.
16:9
4:3 LB
VFP DIMMER
I/P
general room.
TITLE/
GROUP
SOUND
EFFECT
VFP DIMMER
I/P
4:3 PS
¡/1 Fast forward/backward
(While paused)
CINEMA For watching a movie
software in a room with
suppressed light.
ANGLE SUBTITLE AUDIO ZOOM
SLIDE EFFECT
SCART RGB
STANDARD
ANGLE SUBTITLE AUDIO ZOOM
SLIDE EFFECT
Slow-motion playback
The batteries will last about six months with normal use.
If the functions of the remote control become erratic,
replace the batteries.
Using the disc menu
• Each time you press the button,
With the label side up
USER1
USER2
You can adjust
the playback speed changes.
You can operate a disc—SVCD/
VCD with Playback Control*
(PBC)—using the disc menu
shown on the TV screen.
* A method of controlling disc play
for SVCD/VCD by using the disc
menu.
parameters that affect the
picture character and
store the settings as a user
preset. See below.
3 Press 5/∞ to select the monitor type, then press
ENTER.
¢/4 Skip chapter/track
Precautions of the safe use of batteries
Observe the following precautions for the safe use of
batteries. If they are used improperly their lives will be
shortened, they may burst or their contents may leak.
• Remove the batteries from the remote control if it is
not going to be used for a long period of time.
• Remove dead batteries and dispose of them
properly.
• Never leave dead batteries lying around, take them
apart, mix them with other refuse, or throw them into
an incinerator.
• Never touch liquid that has leaked out of a battery.
• Do not mix new and old batteries, or batteries of
different types, when placing them.
• If you press and hold the button
during playback, playback is
advanced/reversed at 5 times
normal speed.
• For a normal (conventional) TV, select “4:3 LB” or
“4:3 PS.” (See “MONITOR TYPE” in “Initial
settings.”)
Zooming the picture
To adjust the picture tone
Each time you press ZOOM, the
magnification changes.
Point toward the remote sensor directly as
possible (the operating range is approx. 5 m.)
• For a wide-screen TV, select “16:9.”
1 Select “USER1” or “USER2.”
2 Press 5/∞ to select a parameter, then press ENTER.
VARIABLE (For DVD Video)
DVD PLAYER SETUP
• You can use 5/∞/2/3 button to
7 For DVD
PLAYBACK The disc is played back at about
1.2 or 1.5 times (FAST)/0.8 or 0.6
times (SLOW) normal speed.
DIGITAL AUDIO OUTPUT
DOLBY DIGITAL/PCM
move the zoomed position.
PCM ONLY
1 Press TOP MENU or MENU to show the disc menu.
2 Press 5/∞/2/3 to select a desired item, then press
ANALOG DOWNMIX
D.RANGE CONTROL
OUTPUT LEVEL
About On-screen guide icons
GAMMA
Adjust this if the neutral color is bright or dark.
The brightness of dark and bright portion is
maintained (LOW/MID/HIGH).
DOLBY DIGITAL/PCM
To return to the normal playback,
select the normal size by pressing
ZOOM repeatedly.
STREAM/PCM
: Playback.
STANDARD
ENTER or 3 (SELECT).
The sound is not muted, and the
subtitle does not go off (except for
DTS).
• With some discs, you can also select items by entering the
number using the numeric buttons.
: Pause.
BRIGHTNESS Adjust this if the picture is bright or dark on the
whole (–16 (darkest) to +16 (brightest)).
/
: Slow-motion playback with the current
speed.
Main display
7 For SVCD/VCD
(For SVCD/VCD)
4 Press 5/∞ to select a desired digital output
signal type, then press ENTER.
• Each indicator lights up when corresponding
function/mode is activated, or corresponding
information is on the main display.
CONTRAST
Adjust this if the far and near position is unnatural
(–12 to +12).
The disc is played back at about
2 times (FAST)/0.5 times (SLOW)
normal speed.
1 While stopped, press TOP MENU or 3 (SELECT) to
show the menu.
/
: Fast forward/backward playback with
the current speed.
Set this item correctly according to the logo on your
receiver or decoder.
(If you do not connect the player to such a device,
press ENTER to finish the setting.)
• Receiver/decoder bearing Dolby Digital logo and
no DTS, select “DOLBY DIGITAL/PCM.”
• Receiver/decoder bearing both Dolby Digital and
DTS logos, select “STREAM/PCM.”
• Receiver/decoder bearing neither Dolby Digital nor
DTS logo, or digital recorder, select “PCM ONLY.”
2 Press the numeric buttons to select a desired item.
To select 5: press 5.
Turning on and off the player
SATURATION Adjust this if the picture is whitish or blackish
Press
STANDBY/ON.
(–16 (blackest) to +16 (whitest)).
(Only for DVD Video)
: At the beginning of a scene containing
multi-angle views.
To select 23: press 2, then 3.
To select 40: press 4, then 0.
The playback position moves
back 10 seconds before the
current position (only within the
same title).
TINT
Adjust this if the appearance of flesh tone is
unnatural (–16 to +16).
• To move to the next or previous page of the current menu,
press ¢ or 4.
: At the beginning of a scene containing
multi-audio sounds.
SHARPNESS Adjust this if the picture is indistinct (LOW/HIGH).
• To return to the previous menu, press RETURN.
: At the beginning of a scene containing
multi-subtitles.
You can change the setting so that the on-screen
guide icons do not appear on the TV screen. (See
“ON SCREEN GUIDE” in “Initial settings.”)
* 38 on the player starts/pauses playback.
Y DELAY
Adjust this if the picture looks separately/
overlapped (–2 to +2).
To play back without PBC
While stopped, press the numeric buttons instead of 3
(SELECT) to start playback.
To reactivate PBC
Changing the display brightness
3 Press 5/∞ to adjust the parameter, then press ENTER.
4 Repeat step 2 and 3 to adjust other parameters.
5 Press VFP-I/P to finish the setting.
To bring up the DVD PLAYER SETUP display later
Press SET UP for a few seconds until the DVD PLAYER
SETUP display appears.
Press DIMMER to change the brightness of
the display window.
• Press TOP MENU or MENU.
• Press 7 to stop playback, then 3 (SELECT).
5
6
7
8
|