Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
KD-S15
CD RECEIVER: INSTRUCTIONS/INSTALLATION
Installation/connection are explained at the last section of this manual (reverse page, indicated with
symbol).
For customer Use:
Enter below the Model No. and Serial No. which
are located on the top or bottom of the cabinet.
Retain this information for future reference.
0508DTSMDTJEIN
Model No.
Serial No.
GET0561-001A
[J]
EN
© 2008 Victor Company of Japan, Limited
ESPAÑOL
ENGLISH
INFORMATION (For U.S.A.)
MAINTENANCE
How to clean the connectors
Wipe the connectors with
a cotton swab or cloth
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
To keep discs clean
Wipe in a straight line from center of disc to
edge. Do not use liquid cleaners, thinners, or
benzene.
moistened with alcohol.
Connectors
Moisture condensation
To play new discs
Remove any rough areas from the inner and
outer edges of the disc.
Moisture may condense on the lens inside the unit. Eject
the disc and leave the unit turned on for a few hours until
the moisture has evaporated.
Caution
Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
Do not use the following discs:
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
Single CD—8 cm (3-3/16”) disc
Warped disc
Sticker and sticker residue
Stick-on label
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified
service personnel.
3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.
(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
Transparent or semi-transparent
parts on its recording area
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
Unusual shape
C-thru Disc (semi-transparent disc)
PREPARATIONS
[European Union only]
How to reset your unit
Detaching the control panel
Reset the unit after installation is complete.
For safety...
Warning
• Do not raise the volume level too much, as this will block
outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
If you need to operate the unit while driving, be sure to
look around carefully or you may be involved in a traffic
accident.
•
Your preset adjustments will also be erased.
Attaching the control panel
Temperature inside the car...
Caution on volume setting
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
Discs produce very little noise compared with other sources.
Lower the volume before playing a disc to avoid damaging
the speakers by the sudden increase of the output level.
How to forcibly eject a disc
MORE ABOUT THIS UNIT
•
•
Be careful not to drop the disc when it ejects.
If this does not work, reset your unit.
General
Basic operations
• This unit has been designed to reproduce CDs/CD Texts,
and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD
(CD-DA).
• After ejecting a disc, “NO DISC” appears and you cannot
operate some of the buttons. Insert another disc or press
SRC to select another playback source.
• By pressing SRC on the unit, you can also turn on the
power. If the source is ready, playback also starts.
• If you turn off the power while listening to a disc, disc
play will start from where it had been stopped previously
next time you turn on the power.
Basic settings
Enter PSM menu.
Cancel the display
demonstration
Set the clock
• When no disc is loaded in the unit, you cannot select “CD”
as the playback source.
Playing a CD-R or CD-RW
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playing.
• Some CD-Rs or CD-RWs may not be played back on this
unit:
– Discs are dirty or scratched.
– Moisture condensation has occurred on the lens inside
the unit.
– The pickup lens inside the unit is dirty.
– The files on the CD-R/CD-RW are written using the
“Packet Write” method.
– There are improper recording conditions (missing data,
etc.) or media conditions (stained, scratched, warped,
etc.).
Select an item.
Adjust.
Tuner operations
• During SSM search...
– All previously stored stations are erased and the
stations are stored anew.
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
– When SSM is over, the station stored in No. 1 will be
automatically tuned in.
Adjust the hour.
Adjust the minute.
Deactivate the display
demonstration.
Disc operations
Caution for DualDisc playback
• The Non-DVD side of a “DualDisc” does not comply with
the “Compact Disc Digital Audio” standard. Therefore, the
use of Non-DVD side of a DualDisc on this product may
not be recommended.
Finish
• CD-RWs may require a longer readout time since the
reflectance of CD-RWs is lower than that of regular CDs.
1– EN
General settings—PSM
SPECIFICATIONS
Enter PSM menu.
Select an item.
Adjust.
Finish
CD player section
Audio amplifier section
Type:
Compact disc player
Power Output:
Signal Detection System: Non-contact optical pickup
(semiconductor laser)
Number of channels:
Frequency Response:
Dynamic Range:
20 W RMS × 4 Channels at 4
≤ 1% THD+N
Signal to Noise Ratio:
Ω
and
2 channels (stereo)
5 Hz to 20 000 Hz
93 dB
Indication
DEMO
Item ( : Initial) Setting
80 dBA (reference: 1 W into 4
Ω
)
• DEMO ON
• DEMO OFF
• ON
:
:
:
:
The display demonstration will be activated automatically if no operation is
done for about 20 seconds.
Cancels.
Signal-to-Noise Ratio:
Wow and Flutter:
98 dB
Load Impedance:
Tone Control Range:
4
Ω
(4
Bass:
Mid-range: 12 dB at 1 kHz
Treble: 12 dB at 7.5 kHz
40 Hz to 20 000 Hz
load (full scale)
Ω
to 8
Ω
allowance)
Less than measurable limit
12 dB at 60 Hz
CLK DISP*1
The clock time is shown on the display at all times when the power is turned
General
off.
Frequency Response:
Power Requirement:
Operating Voltage: DC 14.4 V
(11 V to 16 V allowance)
Negative ground
• OFF
Cancels; pressing DISP will show the clock time for about 5 seconds when the
power is turned off.
Line-Out Level/Impedance: 2.5 V/20 k
Output Impedance: 1 k
Subwoofer-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Ω
Ω
Grounding System:
Allowable Operating Temperature:
0°C to +40°C (32°F to 104°F)
Dimensions (W × H × D):
Installation Size (approx.):
CLOCK H (Hour)
1 – 12
:
:
[Initial: 1 (1:00)]
[Initial: 00 (1:00)]
CLOCK M (Minute) 00 – 59
DIMMER
• ON
• OFF
:
:
Dims the display and button illumination.
Cancels.
182 mm × 52 mm × 160 mm
(7-3/16” × 2-1/16” × 6-5/16”)
Panel Size (approx.):
188 mm × 58 mm × 5 mm
(7-7/16” × 2-5/16” × 1/4”)
Mass (approx.):
Tuner section
Frequency Range:
SCROLL
• ONCE
• AUTO
• OFF
:
:
:
Scrolls the displayed information once.
Repeats scrolling (at 5-second intervals).
Cancels.
FM: 87.5 MHz to 107.9 MHz
(with channel interval set to 100 kHz or 200 kHz)
87.5 MHz to 108.0 MHz
(with channel interval set to 50 kHz)
AM: 530 kHz to 1 710 kHz
• Pressing DISP for more than one second can scroll the display regardless of
the setting.
1.3 kg (2.9 lbs) (excluding accessories)
(with channel interval set to 10 kHz)
531 kHz to 1 602 kHz
(with channel interval set to 9 kHz)
Design and specifications are subject to change without
notice.
L/O MODE
WOOFER*2
AUX ADJ
• REAR
:
:
Select if the REAR LINE OUT terminals are used for connecting the speakers
(through an external amplifier).
Select if the REAR LINE OUT terminals are used for connecting a subwoofer.
• WOOFER
If a kit is necessary for your car, consult your telephone
directory for the nearest car audio speciality shop.
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 μV/75
• LOW
• MID
• HIGH
:
:
:
Frequencies lower than 90 Hz are sent to the subwoofer.
Frequencies lower than 135 Hz are sent to the subwoofer.
Frequencies lower than 180 Hz are sent to the subwoofer.
Ω
)
50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75
Alternate Channel Selectivity (400 kHz): 65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Ω)
Having TROUBLE with operation?
A.ADJ 00
– A.ADJ 05
:
Adjust the auxiliary input level to avoid the sudden increase of the output
level when changing the source from external component connected to the
AUX input jack on the control panel.
Please reset your unit
Still having trouble??
[AM Tuner]
Sensitivity/Selectivity: 20 μV/35 dB
Call 1-800-252-5722 (USA ONLY)
AMP GAIN*3
AREA
• LOW PWR
• HIGH PWR
• AREA US
• AREA EU
• AREA SA
:
:
:
:
:
VOL 00 – VOL 30 (Select if the maximum power of each speaker is less than
50 W to prevent the speaker from being damaged.)
VOL 00 – VOL 50
When using in North/Central/South America. AM/FM intervals are set to
10 kHz/200 kHz.
When using in any other areas. AM/FM intervals are set to 9 kHz/50 kHz
(100 kHz during auto search).
When using in South American countries. AM/FM intervals are set to 10 kHz/
100kHz.
PREPARATION
You need the installation kits which corresponds to your car.
• Mark all the check boxes (
) to make sure you have follow the instructions and the listed parts.
1
*
If the power supply is not interrupted by turning off the ignition key of your car, it is recommended that you select “OFF” to
save the car’s battery.
Displayed only when “L/O MODE” is set to “WOOFER.”
The volume level automatically changes to “VOL 30” if you change to “LOW PWR” while the volume level is set higher than
“VOL 30.”
Check the battery system in your car
2
3
*
*
12 V DC, NEGATIVE ground
TROUBLESHOOTING
Prepare this before installation
Symptoms
Remedies/Causes
• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.
• Check the cords and connections.
• The buttons on the unit do not work as you If you press M MODE, some buttons work differently from it
intended.
original function. Wait for 5 seconds or press M MODE again.
TROUBLESHOOTING
• The fuse blows.
• This unit does not work at all.
Reset the unit.
* Are the red and black leads connected correctly?
• SSM automatic presetting does not work. Store stations manually.
• Power cannot be turned on.
* Is the yellow lead connected?
• Static noise while listening to the radio.
• Disc ejects.
Connect the antenna firmly.
Insert the disc correctly.
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• CD-R/CD-RW cannot be played back.
• Tracks on the CD-R/CD-RW cannot be
skipped.
• Insert a finalized CD-R/CD-RW.
• Finalize the CD-R/CD-RW with the component which you used
for recording.
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• This unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• Disc can be neither played back nor ejected. • Unlock the disc.
• Eject the disc forcibly.
• This unit does not work at all.
• Disc sound is sometimes interrupted.
• Stop playback while driving on rough roads.
* Have you reset your unit?
• Change the disc.
• Check the cords and connections.
• “NO DISC” appears on the display.
• “PLEASE” and “EJECT” appear alternately
on the display.
Insert a playable disc into the loading slot.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
3 – EN
Parts list for installation and connection
A
D
B
C
Control panel
Power cord
Sleeve
Trim plate
G
I
J
K
Mounting bolt—
M4 x 5 mm (M4 x 1/4");
M5 x 12.5 mm (M5 x 1/2")
E
F
H
Handles
Remote controller
Battery
Washer (ø5)
Lock nut (M5)
Rubber cushion
INSTALLATION
If you are not sure how to install this unit correctly, consult your JVC car audio dealer.
In dash-mounting
Removing the unit
Before removing the unit, release the rear section.
When you stand the unit, be careful not to
damage the fuse on the rear.
Do the required electrical
connections.
Bend the appropriate tabs
to hold the sleeve firmly
in place.
When using the optional stay
When installing the unit without using the sleeve
Stay (option)
In a Toyota car for example, first remove the car radio and install the unit in its place.
Fire wall
* Not supplied for this unit.
Flat type screws—M5 × 8 mm (M5 × 3/8")*
Dashboard
Bracket*
Screw (option)
Flat type screws
—M5 × 8 mm (M5 × 3/8")*
Install the unit at an angle of
less than 30˚.
Pocket
Bracket*
ELECTRICAL CONNECTIONS
Make sure to disconnect the battery’s negative terminal.
• Be sure to ground this unit to the car’s chassis again after installation.
High
Note:
It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the
maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page “General setting — PSM“ of the INSTRUCTIONS.).
Heat sink
Typical connections
Rear ground terminal
Connecting the external amplifier or subwoofer
Remote lead
Y-connector *1
Rear line out
Remote lead (blue with white stripe)
Antenna
terminal
Set “L/O MODE” to “REAR”
(See “General settings—PSM.”)
You can connect a power amplifier for
rear speakers.
15 A fuse
To the remote lead of other equipment
or automatic antenna if any
Ignition switch
Black
To the metallic body
or chassis of the car
Connect only the front speakers if your
speaker system is two-speaker system.
JVC Amplifier
Rear
speakers
To a live terminal in the
fuse block connecting to the
car battery (bypassing the
ignition switch) (constant
12 V)
White with black stripe
Right
Yellow *2
Front speakers
Left
Not supplied for this unit.
Set “L/O MODE” to “WOOFER”
(See “General settings—PSM.”)
You can also connect a subwoofer to
the REAR LINE OUT terminals.
Front speaker (left)
White
1
2
*
*
Fuse block
Before checking the operation of this unit prior to installation, this
lead must be connected, otherwise the power cannot be turned on.
Firmly attach the ground wire to the metallic body or to the chassis
of the car—to the place uncoated with paint (if coated with paint,
remove the paint before attaching the wire). Failure to do so may
cause damage to the unit.
Gray with black stripe
Red
To an accessory terminal in
the fuse block
3
*
Front speaker (right) Gray
Green with black stripe
or
JVC Amplifier
Subwoofer
Blue with white
stripe
To the remote lead of other
equipment or automatic antenna if
any (200 mA max.)
4
*
Signal cord (not supplied for this unit)
Rear speaker (left)
Green
PRECAUTIONS on power supply and speaker connections
Purple with black stripe
Rear speaker (right)
Purple
4 – EN
|