Invacare Mobility Aid 1035965 User Manual

WHEELCHAIR TRAY  
Assembly, Installation, and Operating Instructions  
Model No. 1300, 1035965, and 1035966  
6. Repeat STEPS 1-5 for opposite side.  
NOTE: Check all parts for shipping damage and test be-  
fore using. In case of damage, DO NOT use. Contact the  
dealer / Invacare for further instructions.  
7. Remove protective paper from the tray.  
8. Position the tray bracket on the wheelchair tray BOT-  
TOM as shown in FIGURE 1.  
SAFETY SUMMARY  
The following recommendations are made for the  
safe installation of the Wheelchair Tray:  
NOTE:Forwheelchairsover18-incheswide, reversethe  
traybracketswiththesocketspositionedtowardstheout-  
side of the tray.  
WARNING  
9. Install carriage bolts through TOP of wheelchair tray  
and tray bracket.  
DO NOT a sse mble or use this e quipme nt with-  
out first re a ding a nd unde rsta nding this instruc -  
tion she e t. If you a re una ble to unde rsta nd the  
Wa rnings, Ca utions or Instruc tions, c onta c t a  
he a lthc a re profe ssiona l, de a le r or te c hnic a l  
pe rsonne l if a pplic a ble be fore a tte mpting to in-  
sta ll this e quipme nt - othe rwise , injury or da m-  
a ge ma y oc c ur.  
10. Secure the tray bracket to the tray with the two (2)  
wing nuts.  
11. Repeat STEPS 8-10 for opposite side.  
12. Insert the tray support bar into the tray bracket and  
hand tighten the socket screw.  
Any worn or da ma ge d ha rdwa re MUST be re -  
pla c e d.  
13. Insert the tray support bars into the bracket supports  
at the desired position.  
After insta lla tion, repa ir or service a nd BEFORE use,  
ma ke sure a ll a tta ching ha rdwa re is securely tight-  
ened - otherwise, injury or da ma ge ma y result.  
14. Securely tighten the four (4) phillips screws.  
15. Center the tray on the wheelchair.  
NOTE: If the tray will not center, adjust tray support bars.  
INSTALLING WHEELCHAIR TRAY  
(FIGURE 1)  
16. After making sure the tray is centered on the wheel-  
chair, securely tighten the socket screws.  
Tray  
Wheelchair Tray  
Support  
1. Removethetwo(2)phillipsscrewsfromthearmpad.  
2. Slide the bracket support tube into the bar guide as-  
Carriage Bolts  
Bars  
sembly as shown in FIGURE 1.  
Wheelchair  
Frame  
Tray  
Bracket  
NOTE: The bracket of the bar guide assembly and the  
tube of the bracket support should be positioned towards  
the outside of the wheelchair frame.  
Arm Pad  
Socket Screw  
Wing Nuts  
Tab  
3. Looselyinstallphillipsscrewthroughthebracketsup-  
port tab, wheelchair frame and arm pad.  
Bracket  
4. Position the bar guide assembly tab to align with the  
mounting hole of the wheelchair frame.  
Tab  
Bracket Support  
and Tube  
Bar Guide  
Assembly  
5. Loosely install phillips screw through the bar guide  
assembly, wheelchair frame and arm pad.  
Phillips Screws  
FIGURE 1 - INSTALLING WHEELCHAIR TRAY  
Invacare Corporation  
Technical Support  
800-832-4707  
Invacare is a registered trademark of Invacare Corporation  
© 1999 Invacare Corporation  
One InvacareWay  
Elyria, Ohio USA  
44036-2125  
Form No.84-41 P/N 1023704 Rev.B (1) - 11/99  
800-333-6900  
 

Infinity Portable Speaker 35c User Manual
Ingersoll Rand Heat Pump 650941 XXE C User Manual
Integra Printer CROMA24 User Manual
IOGear Mouse GME222 User Manual
Jenn Air Oven JMW9527DAB User Manual
JVC Flat Panel Television LT 52P789 User Manual
JVC Projection Television HD 56G786 User Manual
Karcher Pressure Washer K 5690 User Manual
Kelvinator Refrigerator ER 1531T User Manual
KitchenAid Dishwasher W10321621D User Manual