Interfire Audio Speaker IFC 525 User Manual

COMPONENT WOOFER INSTALLATION INSTRUCTION MANUAL  
COMPONENT WIRING DIAGRAM:  
EXTERNAL 2-WAY  
CROSSOVER  
MOUNTING LOCATION  
Carefully select a suitable mounting location for the speaker/tweeter. Be sure to check  
behind the mounting location selected for adequate space for speaker/tweeter depth.  
Use the included template if needed  
MOUNTING HOLE  
SPEAKER : Using a sharp knife or razor, cut the panel using the outline from the template as a guide. Also,  
drill holes for the mounting screws if installing on metal panels.  
SIGNAL SOURCE UNIT  
RADIO OR AMPLIFIER  
INSTALLATION  
SPEAKER : Place ABS grill on top of speaker and secure assembly using the self tapping  
screw provided. *NOTE : If not using the included grill, grill mount does not have to be installed.  
TWEETER : Screw the angle mounting to the location selected or use the double sided  
tape provided to stick the flush mounting to the location selected.  
WIRING  
SPEAKER: Carefully route the supplied wire to the speaker, ensuring that it does not pass over any sharp  
metal edges that will damage the signal path. Connect the terminal ends of the wires to the speakers,  
watching that the left/right and positive/negative connections are made correctly to the appropriate  
outputs of the radio or amplifier.  
TWEETER : Feed the wires from the tweeter through the flush/angle mounting opening  
and connect these wires to the line wires coming from the included outboard crossover tweeter  
terminals. Push the tweeter into the flush/angle mounting until the tweeter sits nicely into the mounting.  
SPECIFICATIONS :  
MODEL: IFC-525  
*NOTE : When installing tweeter with flush mount kit, a hot glue gun is sometimes necessary to secure  
the tweeter's flush mount housing.  
MODEL: IFC-650  
5.25" 2-Way High Definition  
Component System  
6.5" 2-Way High Definition  
Component System  
5.25" Injection PP Mica Cone  
Rubber Surround and  
1" Titanium Dome Tweeter  
with Neodymium Magnet  
6.5" Injection PP Mica Cone  
Rubber Surround and  
1" Titanium Dome Tweeter  
with Neodymium Magnet  
INSTALLATION PROCEDURE :  
Mounting Holes  
Peak Power Handling  
: 300Watts  
Peak Power Handling  
: 350Watts  
Continuous Power (RMS) : 150 Watts  
Continuous Power (RMS) : 175 Watts  
Impedance  
: 4 Ohm  
Impedance  
: 4 Ohm  
Magnet Weight  
Sensitivity (1W/m)  
Freq. Response  
Woofer Voice Coil Dia.  
Fo (Freq. Resp.)  
Qts (Total Q)  
Vas  
: 10 Oz  
Magnet Weight  
Sensitivity (1W/m)  
Freq. Response  
Woofer Voice Coil Dia.  
Fo (Freq. Resp.)  
Qts (Total Q)  
Vas  
: 13 Oz  
: 91 dB  
: 91 dB  
Angle Mounting  
: 50Hz - 25kHz  
: 1" (25mm) ASV  
: 92.06 Hz  
: 0.82  
: 40Hz - 25kHz  
: 1" (25mm) ASV  
: 53.1 Hz  
: 0.61  
Speaker Unit  
Screw  
Grill  
Mounting Screws  
: 4.1 Lt  
: 12.42 Lt  
: 12dB/Oct  
Tweeter  
Crossover  
: 12dB/Oct  
Crossover  
Speaker  
Double sided  
Tape  
Flush Mounting  
Interfire Audio Inc.  
Santa Fe Springs, CA, www.inter fireaudio.com  
Tweeter  
 

Indesit Washer IWB6065 User Manual
IOGear Network Card GDIP201 User Manual
iOptron Telescope 8600 User Manual
Jackson Dishwasher JV 24 B BF User Manual
JBL Professional Car Speaker Control 28 User Manual
JVC Camcorder 0503 FO ID VP User Manual
JVC Car Speaker CS HX7 User Manual
JVC Headphones HAFR50P User Manual
Kenwood MP3 Docking Station KDC U549BT User Manual
Kompernass Heat Gun PHLG 2000 SE User Manual