Ingersoll Rand Webcam PE10X XXX XXX XXXX User Manual

PE10X-XXX-XXX-XXXX  
PE15X-XXX-XXX-XXXX  
OPERATOR’S MANUAL  
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE  
PE20X-XXX-XXX-XXXX  
PE30X-XXX-XXX-XXXX  
RELEASED:  
(REV. B)  
3-26-13  
ELECTRONIC INTERfACE  
for Diaphragm Pumps  
READ THIS MANUAL CAREfULLY BEfORE INSTALLING,  
OPERATING OR SERVICING THIS EQUIPMENT.  
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.  
PUMP DATA  
PE10X-XXX-XXX-XXXX is PE series 1” EXP Diaphragm Pumps with  
MODEL DESCRIPTION CHART  
PEXX X -X X X X  
-XXX-XXX  
electronic interface  
PE15X-XXX-XXX-XXXX is PE series 1- 1/2” EXP Diaphragm Pumps  
with electronic interface  
PE20X-XXX-XXX-XXXX is PE series 2” EXP Diaphragm Pumps with  
Pump Size  
10 - 1” EXP Diaphragm Pumps  
15 - 1- 1/2” EXP Diaphragm Pumps  
20 - 2” EXP Diaphragm Pumps  
30 - 3” EXP Diaphragm Pumps  
electronic interface  
PE30X-XXX-XXX-XXXX is PE series 3” EXP Diaphragm Pumps with  
electronic interface  
Center Section  
A - Aluminium  
S - Stainless Steel  
R - Polypropylene  
GENERAL DESCRIPTION  
Revision Level  
This manual is supplemental information for the electronic  
interface options on the PE series of pumps. For complete  
pump installation, disassembly and reassembly, safety infor-  
mation, and other general pump information, please refer to  
the PD pump manual that was also included with the pump.  
This electronic interface includes options for solenoid control,  
end of stroke feedback, leak detection (diaphragm failure),  
cycle counting on the major valve, and a ported motor with  
no major valve for user-supplied control directly to the two  
diaphragm air chambers.  
Specialty Code 1 (Blank if no Speciality Code  
)
A - Solenoid 120VAC  
B - Solenoid 12VDC  
C - Solenoid 240VAC  
D - Solenoid 24VDC  
G - Solenoid 12VDC ATEX  
H -  
Solenoid 24VDC ATEX  
K - Solenoid 220VAC ATEX  
N - Solenoid with no coil  
P - Ported Motor (no major valve provided)  
S - Cycle Sensing on Major Valve  
0 -  
Standard Valve Block ( No Solenoid)  
Solenoid control allows the cycle rate of the pump to be con-  
trolled electronically.  
Specialty Code 2 (Blank if no Speciality Code  
)
E - End of stroke feedback + Leak Detection  
F - End of stroke feedback  
L - Leak Detection  
With Solenoid control, when the solenoid is energized, the  
pump strokes and dispenses the fluid in one chamber. When  
the solenoid is de-energized, the pump strokes in the oppo-  
site direction, dispensing the fluid in the other chamber.  
By providing continuous ON - OFF signals to the solenoid, the  
fluid transfer rate may be increased or decreased remotely.  
End of stroke feedback can be used in conjunction with the  
solenoid valve to cycle the pump based upon completion of  
each stroke.  
0 - No Option  
Special Testing  
Testing for special testing options, please contact your  
nearest ARO Customer Service Representative or Distributor.  
The leak detection option incorporates an optical fluid sensor  
in each air chamber to provide a signal when a diaphragm  
has failed and fluid is leaking through the pump.  
The cycle counter option provides a closed contact output  
each time the pump completes a cycle. This option is not  
available combined with solenoid control.  
The ported motor with no major valve is provided as an op-  
tion for users who want to supply compressed air directly to  
each diaphragm and control the operation of the pump with  
their own external air controls  
.
INGERSOLL RAND COMPANY LTD  
209 NORTH MAIN STREET – BRYAN, OHIO 43506  
(800) 495-0276 FAX (800) 892-6276  
© 2013  
CCN 46750816  
 
PARTS LIST / PEXXS-XXX-XXX-XXXX  
Part no  
Item Description  
Spool  
Qty  
Part no  
Item Description  
Qty  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
410  
411  
413  
414  
(for Cycle Sensing)  
(PEXXS-XXX-XXX-XSXX)  
Sensor  
95276  
111  
95835  
(1)  
PE10S-XXX-XXX-X0XX, PE15S-XXX-  
(
XXX-X0XX)  
(for Cycle Sensing)  
(PEXXS-XXX-XXX-XSXX)  
Adapter  
PE10S-XXX-XXX-XSXX, PE15S-XXX-  
XXX-XSXX)  
96583  
(
95835-1  
95835-2  
95651  
(1)  
(1)  
(1)  
(1)  
(1)  
(2)  
(4)  
Adapter Plate  
119380  
All PE10S, PE15S with Solenoid  
(AII PEXXS with SoIenoid)  
PXXXS-XXX-XXX-  
Coil ,120 VAC (  
PE20S-XXX-XXX-X0XX, PE30S-XXX-  
XXX-X0XX)  
116218-33  
116218-38  
116218-35  
116218-39  
117345-38  
117345-39  
117345-35  
(
)
XAXX  
Coil ,12 VDC  
PE20S-XXX-XXX-XSXX, PE30S-XXX-  
XXX-XSXX)  
(
)
PXXXS-XXX-XXX-XBXX  
95651-1  
95651-2  
96323  
(
Coil ,240 VAC  
All PE20S, PE30S with Solenoid  
)
PXXXS-XXX-XXX-XCXX  
(
Coil ,24 VDC  
121  
134  
Sleeve  
)
)
PXXXS-XXX-XXX-XDXX  
(
(PEXXS-XXX-XXX-XPXX)  
Coil, 12 VDC ATEX  
(M6 x 1 - 6g x 20 mm)  
Screw  
PXXXS-XXX-XXX-XGXX  
96340  
(
(PEXXS-XXX-XXX-XPXX)  
Coil, 24 VDC ATEX  
135 Valve Block  
)
PXXXS-XXX-XXX-XHXX  
(
95939-3  
(1)  
PE10S-XXX-XXX-XSXX, PE10S-XXX-  
XXX-X0XX)  
(
Coil, 220 VAC ATEX  
)
PXXXS-XXX-XXX-XKXX  
(
PE15S-XXX-XXX-XSXX, PE15S-XXX-  
XXX-X0XX)  
(
95939-1  
95939-6  
95939-5  
(1)  
(1)  
(1)  
(AII PEXXS with Solenoid)  
415 O-Ring  
416 O-Ring  
417 Screw  
114103  
114104  
96728647  
15309974  
96957  
(1)  
(1)  
(2)  
(1)  
(1)  
(1)  
(1)  
All PE10S with Solenoid  
(AII PEXXS with Solenoid)  
(AII PEXXS with Solenoid)  
All PE15S with Solenoid  
PE20S-XXX-XXX-XSXX, PE20S-XXX-  
XXX-X0XX, PE30S-XXX-XXX-XSXX,  
PE30S-XXX-XXX-X0XX)  
(
(AII PEXXS with Solenoid)  
(AII PEXXS with Solenoid)  
(AII PEXXS with Solenoid)  
418 Tube  
419 Seal  
96337-1  
(1)  
All PE20S, PE30S with Solenoid  
96337-3  
114102  
(1)  
(1)  
420 Snap Ring  
Y147-43  
96954  
403  
(AII PEXXS with SoIenoid)  
Valve  
(AII PEXXS with Solenoid)  
421 Retainer  
(for Cycle Sensing)  
(PEXXX-XXX-XXX-XSXX)  
Magnet  
425  
407 Adapter  
95275  
(1)  
(1)  
(1)  
(PEXXS-XXX-XXX-XAXX, PEXXS-XXX-  
XXX-XBXX, PEXXS-XXX-XXX-XCXX,  
PEXXS-XXX-XXX-XDXX, PEXXS-XXX-  
XXX-XGXX, PEXXS-XXX-XXX-XHXX,  
PEXXS-XXX-XXX-XKXX, PEXXS-XXX-  
XXX-XNXX)  
(AII PEXXS with Solenoid)  
428 O-Ring  
Y325-13  
116464  
96953  
(1)  
Solenoid Muffler  
429  
(AII PEXXS with Solenoid)  
PEXXP-XXX-XXX-XXXX (en)  
Page 3 of 16  
 
PARTS LIST / PEXXR-XXX-XXX-XXXX  
Part no  
95276  
Part no  
Item Description  
Qty  
(1)  
Item Description  
Spool  
Qty  
410  
411  
413  
414  
(for Cycle Sensing)  
(PEXXR-XXX-XXX-XSXX)  
Sensor  
111  
96293  
(1)  
PE10R-XXX-XXX-X0XX, PE15R-XXX-  
(
XXX-X0XX)  
(for Cycle Sensing)  
(PEXXR-XXX-XXX-XSXX)  
Adapter  
96581  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
(1)  
PE10R-XXX-XXX-XSXX, PE15R-XXX-  
XXX-XSXX)  
(
96293-1  
96293-2  
95651  
(1)  
(1)  
(1)  
(1)  
(1)  
(2)  
(4)  
Coil Nut  
119380  
(AII PEXXR with SoIenoid)  
All PE10R, PE15R with Solenoid  
PXXXR-XXX-XXX-  
Coil ,120 VAC (  
116218-33  
116218-38  
116218-35  
116218-39  
117345-38  
117345-39  
117345-35  
PE20R-XXX-XXX-X0XX, PE30R-XXX-  
XXX-X0XX)  
)
XAXX  
(
Coil ,12 VDC  
PE20R-XXX-XXX-XSXX, PE30R-XXX-  
XXX-XSXX)  
)
PXXXR-XXX-XXX-XBXX  
(
(
95651-1  
95651-2  
96323  
Coil ,240 VAC  
)
PXXXR-XXX-XXX-XCXX  
(
All PE20R, PE30R with Solenoid  
Coil ,24 VDC  
)
)
PXXXR-XXX-XXX-XDXX  
(
Sleeve  
121  
134  
(PEXXR-XXX-XXX-XPXX)  
Coil, 12 VDC ATEX  
PXXXR-XXX-XXX-XGXX  
(
(M6 x 1 - 6g x 20 mm)  
Screw  
96340  
(PEXXR-XXX-XXX-XPXX)  
Coil, 24 VDC ATEX  
)
PXXXR-XXX-XXX-XHXX  
(
135 Valve Block  
96174-1  
(1)  
PE10R-XXX-XXX-XSXX, PE10R-XXX-  
XXX-X0XX)  
(
Coil, 220 VAC ATEX  
)
PXXXR-XXX-XXX-XKXX  
(
PE15R-XXX-XXX-XSXX, PE15R-XXX-  
XXX-X0XX)  
(
95834-1  
96174-4  
95834-4  
(1)  
(1)  
(1)  
(AII PEXXR with Solenoid)  
415 O-Ring  
416 O-Ring  
417 Screw  
114103  
114104  
(1)  
(1)  
(AII PEXXR with Solenoid)  
(AII PEXXR with Solenoid)  
All PE10R with Solenoid  
96728647  
15309974  
96957  
(2)  
(1)  
(1)  
(1)  
All PE15R with Solenoid  
(AII PEXXR with Solenoid)  
418 Tube  
419 Seal  
PE20R-XXX-XXX-XSXX, PE20R-XXX-  
XXX-X0XX, PE30R-XXX-XXX-XSXX,  
PE30R-XXX-XXX-X0XX)  
(
95789-1  
(1)  
(AII PEXXR with Solenoid)  
(AII PEXXR with Solenoid)  
420 Snap Ring  
Y147-43  
All PE20R, PE30R with Solenoid  
95789-3  
11481-7  
114102  
(1)  
(1)  
(1)  
303  
Plastic Plug  
(
(AII PEXXR with Solenoid)  
421 Retainer  
96954  
(1)  
(1)  
(1)  
(1)  
PEXXR-XXX-XXX-XPXX)  
(for Cycle Sensing)  
(PEXXX-XXX-XXX-XSXX)  
Magnet  
425  
95275  
(AII PEXXR with SoIenoid)  
403 Valve  
407 Adapter  
(AII PEXXR with Solenoid)  
428 O-Ring  
Y325-13  
116464  
(PEXXR-XXX-XXX-XAXX, PEXXR-XXX-  
Solenoid Muffler  
XXX-XBXX, PEXXR-XXX-XXX-XCXX,  
PEXXR-XXX-XXX-XDXX, PEXXR-XXX-  
XXX-XGXX, PEXXR-XXX-XXX-XHXX,  
PEXXR-XXX-XXX-XKXX, PEXXR-XXX-  
XXX-XNXX)  
429  
(AII PEXXR with Solenoid)  
96953  
(1)  
PEXXP-XXX-XXX-XXXX (en)  
Page 4 of 16  
 
PARTS LIST / PEXXX-XXX-XXX-XXXX  
Part no  
Y17-51-6  
93832-3  
59632-1  
Item Description  
Pipe Plug  
Qty  
Part no  
96969  
Item Description  
Qty  
422 Manifold  
(PEXXA-XXX-XXX-XXfX, PEXXA-XXX-  
74  
(2)  
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-  
XXX-XX0X),(PEXXS-XXX-XXX-XXfX,  
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,  
PEXXS-XXX-XXX-XXfX)  
PEXXS-XXX-XXX-XX0X)  
(1)  
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-  
XXX-XX0X)  
(2)  
(1)  
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-  
XXX-XX0X)  
Plug  
423 Nut  
(PEXXA-XXX-XXX-XXLX, PEXXA-XXX-  
XXX-XX0X),(PEXXS-XXX-XXX-XXLX,  
PEXXS-XXX-XXX-XX0X)  
126  
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-  
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,  
PEXXS-XXX-XXX-XXfX)  
(1)  
96724182  
96712666  
96964  
283 Diaphragm failure Detector  
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-  
XXX-XXLX),(PEXXS-XXX-XXX-XXEX,  
PEXXS-XXX-XXX-XXLX)  
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-  
XXX-XX0X)  
96270-1  
(2)  
-
424 Lock Washer  
(0.417 ft)  
404 Tubing  
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-  
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,  
PEXXS-XXX-XXX-XXfX)  
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-  
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,  
PEXXS-XXX-XXX-XXfX)  
(1)  
(1)  
94981-XXX-X  
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-  
XXX-XX0X)  
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-  
XXX-XX0X)  
426 Mounting Strap  
405 Elbow  
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-  
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,  
PEXXS-XXX-XXX-XXfX)  
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-  
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,  
PEXXS-XXX-XXX-XXfX)  
59756-103  
59764-4  
(1)  
(1)  
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-  
XXX-XX0X)  
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-  
XXX-XX0X)  
427 Pressure Sensor  
408 Male Connector fitting  
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-  
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,  
PEXXS-XXX-XXX-XXfX)  
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-  
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,  
PEXXS-XXX-XXX-XXfX)  
(1)  
96961  
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-  
XXX-XX0X)  
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-  
XXX-XX0X)  
412 Wiring  
(PEXXA-XXX-XXX-XXEX, PEXXA-XXX-  
XXX-XXfX),(PEXXS-XXX-XXX-XXEX,  
PEXXS-XXX-XXX-XXfX)  
96965  
(1)  
(PEXXR-XXX-XXX-XXfX, PEXXR-XXX-  
XXX-XX0X)  
Page 5 of 16  
PEXXP-XXX-XXX-XXXX (en)  
 
SOLENOID  
GENERAL DESCRIPTION  
Without end of stroke feedback, solenoid control can only  
be used to cycle the pump based on timing. The following  
curves represent the flow rates of a pump based on timed  
operation of the solenoid at a common operating point of 70  
psi air pressure and 30 psi of back pressure.  
figure 3  
figure 1  
figure 2  
PEXXP-XXX-XXX-XXXX (en)  
Page 6 of 16  
 
SOLENOID PART LIST / PEXXX-XXX-XXX-XXXX  
429  
413  
414  
417  
403  
415  
418  
416  
407  
428  
105  
233  
107  
200  
141  
140  
135  
133  
134  
139  
421  
420  
419�  
111  
138�  
137�  
136  
107  
236  
figure 4  
LUBRICATION / SEALANTS  
Apply Lubriplate fML-2 grease (94276) to all “O” rings,  
“U” cups and mating parts.  
Page 7 of 16  
PEXXP-XXX-XXX-XXXX (en)  
 
END Of STROKE  
SETTING / OPERATION  
GENERAL DESCRIPTION  
With end of stroke feedback from a pressure switch, the  
solenoid can be used to cycle the pump based on known feed-  
back that the pump has fully completed each stroke.  
+
pnp  
9.6 to  
32 V  
1
500mA  
2
1
DC  
pnp  
500mA  
4
3
-
PRESSURE SWITCH OPERATION  
Set  
2
3
5
A calibration procedure is necessary for proper operation of  
the pressure switch and accurate end of stroke feedback from  
the pump. The Reset ring will always have a lower pressure  
value than the Set ring.  
Reset  
6
4
1. Determine the operating air pressure of the pump.  
2. The Reset ring should be set to approximately 25% of the  
operating pressure of the pump with a minimum of 10 PSI.  
3. The Set ring should be set to approximately 50% of the  
operating pressure of the pump. This value is more vari-  
able depending on the specific operating conditions. The  
switch may function properly at much lower values for  
the Set ring if the pump is running slowly, or at lower op-  
erating pressures. In general, high operating speeds and  
pressures require a higher setting value of the Set ring.  
4. Operate the pump slowly to ensure proper operation of  
the pressure switch. When the pump has shifted to one  
side, the yellow LED will illuminate and remain on until  
the pump shifts back to the opposite side.  
7
figure 5  
1. Locking Ring  
2. Setting Rings (manually adjustable after unlocking)  
3. LED green: supply voltage O.K.  
4. Process connection ¼NPT; tightening torque 25 Nm  
5. Setting Marks  
6. LED yellow: Set values reached, OUT1 = ON / OUT2 = OFF  
7. Internal Thread M5  
Minimum distance between Set and Reset = 2% of the  
final value of the measuring range.  
To obtain the setting accuracy: Set both rings to the mini-  
mum value, then set the requested value.  
5. If the operating pressure of the pump changes, the  
Set ring may need to be adjusted accordingly.  
PART LIST / PEXXX-XXX-XXX-XXEX, PEXXX-XXX-XXX-XXfX  
423  
424  
426  
422  
427  
412  
405  
404  
408  
figure 6  
PEXXP-XXX-XXX-XXXX (en)  
Page 8 of 16  
 
LEAK DETECTION (DIAPHRAGM fAILURE DETECTOR)  
The diaphragm failure detector components must be  
GENERAL DESCRIPTION  
installed by a qualified electrician in compliance with all  
national, state and local codes and regulations to reduce  
the risk of electrical shock or other serious injury during  
installation and operation.  
An ARO® diaphragm pump equipped with the ARO  
Diaphragm Failure Detector warns of a diaphragm failure by  
sensing the presence of liquid in the air chamber of the pump.  
This system uses a liquid sensor in each of the two air cham-  
bers which will send an output signal when fluid is detected.  
ARO is not responsible for accidents resulting from im-  
proper installation of components or hardware.  
HAZARDOUS VOLTAGE. Do not attempt any service  
without disconnecting all electrical supply sources.  
INSTALLATION AND WARNINGS  
NOTE: ALL WIRING MUST COMPLYWITH ALL LOCAL  
AND / OR NATIONAL ELECTRICAL CODES.  
Electrical codes that apply must be strictly adhered to;  
failure to do so may lead to shock hazard or serious injury.  
Some local electrical codes may require the installation of  
rigid conduit.  
PART LIST / PEXXX-XXX-XXX-XXEX, PEXXX-XXX-XXX-XXLX  
283  
figure 7  
LEAK DETECTION (DIAPHRAGM fAILURE DETECTOR) - PINOUT DESCRIPTIONS  
96270-1 SENSOR PINOUTS  
B
C
A
Pinout  
Function  
+24 VDC  
Ground  
Signal  
A
B
C
TURCK (PICOFAST) Connector PSW 3M -*/S90  
figure 8  
Page 9 of 16  
PEXXP-XXX-XXX-XXXX (en)  
 
CYCLE COUNTER  
This signal may be used to record cycles for maintenance pur-  
poses or batching if the discharge volume of each complete  
cycle is known.  
GENERAL DESCRIPTION  
The ARO diaphragm pump cycle counter provides a closed  
contact output each time the pump completes a cycle.  
PART LIST - PEXXA-XXX-XXX-XSXX / PEXXS-XXX-XXX-XSXX  
126  
166k  
233  
140  
141k  
135  
133  
134  
k 138  
200k  
132k 176k 101 181 103  
111  
k 139  
k 137  
128  
136  
105  
411  
410  
LUBRICATION / SEALANTS   
Apply Lubriplate fML-2 grease (94276) to all “O” rings,  
“U” cups and mating parts.  
figure 9  
PEXXP-XXX-XXX-XXXX (en)  
Page 10 of 16  
 
PART LIST - PEXXR-XXX-XXX-XSXX  
126  
166k  
233  
140  
141k  
107  
105  
133  
134  
135  
200k  
132k 176k 101 181 103  
k 138  
111  
k 139  
k 137  
136  
107  
236  
411  
410  
LUBRICATION / SEALANTS   
Apply Lubriplate fML-2 grease (94276) to all “O” rings,  
“U” cups and mating parts.  
figure 10  
Page 11 of 16  
PEXXP-XXX-XXX-XXXX (en)  
 
As a SOURCING switch (see figure 1) for use with PLC’s.  
As a SINKING switch (see figure 2) for use with PLC’s.  
As a closed contact switch (see figure 3) for use with meters.  
OPERATION  
Maximum Operating Voltage . . . . . . . . . 200 V DC  
Switching Current . . . . . . . . . . . . . . . . . . . . 0.5 Amps  
The pump may be interfaced with a control device in the  
following ways:  
Sourcing Switch  
+V  
INPUT  
Figure 1  
Figure 2  
Figure 3  
Sinking Switch  
INPUT  
Closed Contact Switch  
INPUTS  
figure 11  
Page 12 of 16  
PEXXP-XXX-XXX-XXXX (en)  
 
PORTED NO MOTOR OPTIONS  
PART LIST- PEXXA-XXX-XXX-XPXX / PEXXS-XXX-XXX-XPXX  
166 k  
121  
173 k  
173 k  
121  
160  
133  
134  
43  
132 k  
176 k  
101 181 103  
figure 12  
PART LIST- PEXXR-XXX-XXX-XPXX  
166 k 121  
173 k  
173 k  
121  
133  
160  
134  
132 k  
176 k  
101 181 103  
figure 13  
LUBRICATION / SEALANTS   
Apply Lubriplate fML-2 grease (94276) to all “O” rings,  
“U” cups and mating parts.  
PEXXP-XXX-XXX-XXXX (en)  
Page 13 of 16  
 
Page 14 of 16  
PEXXP-XXX-XXX-XXXX (en)  
 
PEXXP-XXX-XXX-XXXX (en)  
Page 15 of 16  
 
PN 97999-1652  
Page 16 of 16  
PEXXP-XXX-XXX-XXXX (en)  
 

Indesit Washer iwsne61253 User Manual
Infinity Portable Speaker SAT 450 OM User Manual
Invacare Bathroom Aids 91 2 User Manual
Jeep Car Video System 50 0284x 015 Series User Manual
JVC Camcorder LYT2077 001B M User Manual
JVC DVD Player XV N650B User Manual
JVC Projector AV P950E User Manual
Kensington Laser Pointer k72336us User Manual
King Canada Lathe KWL 1016C User Manual
KitchenAid Range KERS807SBB User Manual