PD15X-XXX-XXX
OPERATOR’S MANUAL
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
PE15X-XXX-XXX
RELEASED:
REVISED:
(REV. 16)
8-7-03
5-12-10
1-1/2” DIAPHRAGM PUMP
1:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637389 for air section repair (see page 6).
637375-XXforfluidsectionrepair(seepage4).NOTE:Thiskitalsocon-
tains several air motor seals which will need to be replaced.
637390-X major air valve assembly (see page 7).
PUMP DATA
Models . . . . . . . . . . . . . see Model Description Chart for “-XXX”.
Pump Type . . . . . . . . . . MetallicAirOperatedDoubleDiaphragm
Material . . . . . . . . . . . . . see Model Description Chart.
Weight . . . PX15R-XAX-XXX . . . . . . . 37.65 lbs (17.08 kgs)
PX15R-XCX-XXX . . . . . . 73.2 lbs (33.2 kgs)
PX15R-XHX-XXX . . . . . . 86.9 lbs (39.4 kgs)
Figure 1
PX15R-XSX-XXX . . . . . . . 61.2 lbs (27.8 kgs)
MODEL DESCRIPTION CHART
add 2.14 lbs (0.97 kg) for aluminum air motor section
add 18.14 lbs (8.23 kg) for stainless steel air motor section
P X 15 X - X X X - X X X
Maximum Air Inlet Pressure . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Material Inlet Pressure . . . . . 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure . . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Flow Rate (flooded inlet) . . . . 123 g.p.m. (465.6 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g. . . . 0.617 gal. (2.34 lit.)
Maximum Particle Size . . . . . . . . . . . . 1/4” dia. (6.4 mm)
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM . . . . . . . . . . . -60_to280_F (-51_to 138_C)
HytrelR . . . . . . . . . . . . . . . -20_ to 150_ F (-29_ to 66_ C)
Nitrile . . . . . . . . . . . . . . . . . 10_ to 180_ F (-12_ to 82_ C)
Polypropylene . . . . . . . . . . . 35_ to 175_ F (2_ to 79_ C)
SantopreneR . . . . . . . . . . . -40_to225_F (-40_to 107_C)
PTFE . . . . . . . . . . . . . . . . . 40_ to 225_ F (4_ to 107_ C)
VitonR . . . . . . . . . . . . . . . . -40_to350_F (-40_to 177_C)
Dimensional Data . . . . . . . . . . . . . . . . see page 8
Mounting Dimension . . . . . . . 9” x 11.75” (228.6 mm x 298.5 mm)
Noise Level @ 70 p.s.i., 60 c.p.m. . . . . . 82.8 db(A){
Electronic Interface
D - None E - Available
Center Section Material
A - Aluminum
R - Polypropylene
S - Stainless Steel
Fluid Connection
A - 1-1/2 - 11-1/2 N.P.T.F.
B - Rp 1-1/2 (1-1/2 - 11 BSP, parallel)
Y - 1-1/2” A.N.S.I. / DIN Flange
Fluid Caps & Manifold Material
A - Aluminum
C - Cast Iron
Hardware Material
P - Plated Steel
H - Hastelloy - C
S - Stainless Steel
S - Stainless Steel
Seat Material
A - Santoprene
C - Hytrel
E - Carbon Steel
F - Aluminum
G - Nitrile
H - Hard 440 Stainless Steel
L - Hastelloy - C
S - 316 Stainless Steel
The pump sound pressure levels published here have been updated to an Equivalent
Continuous Sound Level (L ) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
Aeq
ROP S5.1 using four microphone locations.
Ball Material
A - Santoprene
C - Hytrel
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
S
T
V
- 316 Stainless Steel
- PTFE
- Viton
G - Nitrile
Diaphragm Material
A - Santoprene
C - Hytrel
M - Medical Grade Santoprene
V - Viton
T - PTFE / Santoprene
G - Nitrile
FLUID SECTION SERVICE KIT SELECTION
PX15X - XXX - X X X
637375 - X X
EXAMPLE: Model # PD15A-ASP-SAA
Fluid Section Service Kit # 637375-AA
Ball
Diaphragm
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
(800)495-0276 D FAX (800) 892-6276
E2010
CCN 15197213
GENERAL DESCRIPTION
OPERATING INSTRUCTIONS
The ARO diaphragm pump offers high volume delivery even at low air
pressure and a broad range of material compatibility options available.
Refer to the model and option chart. ARO pumps feature stall resistant
design, modular air motor / fluid sections.
Air operated double diaphragm pumps utilize a pressure differential in
theairchamberstoalternatelycreatesuctionandpositivefluidpressure
in the fluid chambers, ball checks insure a positive flow of fluid.
Pump cycling will begin as air pressure is applied and it will continue to
pump and keep up with the demand. It will build and maintain line pres-
sure and will stop cycling once maximum line pressure is reached (dis-
pensing device closed) and will resume pumping as needed.
S Always flush the pump with a solvent compatible with the material
being pumped ifthe materialbeingpumpedissubjectto“settingup”
when not in use for a period of time.
S Disconnecttheairsupplyfromthepumpifitistobeinactiveforafew
hours.
PARTS AND SERVICE KITS
Refertothepartviewsanddescriptionsasprovidedonpage4through7
for parts identification and Service Kit information.
S Certain ARO “Smart Parts” are indicated which should be available
for fast repair and reduction of down time.
S Service kits are divided to service two separate diaphragm pump
functions: 1. AIR SECTION, 2. FLUID SECTION. The FLUID SEC-
TION is divided further to match typical part MATERIAL OPTIONS.
AIR AND LUBE REQUIREMENTS
WARNING EXCESSIVE AIR PRESSURE. Can cause pump
damage, personal injury or property damage.
S Afiltercapableoffilteringoutparticleslargerthan50micronsshould
beusedontheairsupply. Thereisnolubricationrequiredotherthan
the “O” ring lubricant which is applied during assembly or repair.
S Iflubricatedairispresent,makesurethatitiscompatiblewiththe“O”
rings and seals in the air motor section of the pump.
MAINTENANCE
S Provide a clean work surface to protect sensitive internal moving
partsfromcontaminationfromdirtandforeignmatter duringservice
disassembly and reassembly.
S Keep good records of service activity and include pump in preven-
tive maintenance program.
S Before disassembling, empty captured material in the outlet man-
ifold by turning the pump upside down to drain material from the
pump.
INSTALLATION
S Verify correct model / configuration prior to installation.
S Retorque all external fasteners per specifications prior to start up.
S Pumpsaretestedinwateratassembly. Flushpumpwithcompatible
fluid prior to installation.
FLUID SECTION DISASSEMBLY
S When the diaphragm pump is used in a forced-feed (flooded inlet)
situation, it is recommended that a “Check Valve” be installed at the
air inlet.
1. Remove (61) outlet manifold and (60) inlet manifold.
2. Remove (22) balls, (19) “O” rings (if applicable) and (21) seats.
3. Remove (15) fluid caps.
NOTE: Only PTFE diaphragm models use a primary diaphragm (7) and
a backup diaphragm (8). Refer to the auxiliary view in the Fluid Section
illustration.
4. Remove the (14) screw, (6) diaphragm washer, (7) or (7 / 8) dia-
phragms, and (5) backup washer.
NOTE: Do not scratch or mar the surface of (1) diaphragm rod.
S Material supply tubing should be at least the same diameter as the
pump inlet manifold connection.
S Material supply hose must be reinforced, non-collapsible type com-
patible with the material being pumped.
S Piping must be adequately supported. Do not use the pump to sup-
port the piping.
S Use flexible connections (such as hose) at the suction and dis-
charge. These connections should not be rigid piped and must be
compatible with the material being pumped.
FLUID SECTION REASSEMBLY
S Secure the diaphragm pump legs to a suitable surface (level and
flat) to insure against damage by vibration.
S Reassemble in reverse order. Refer to the torque requirements on
page 5.
S Clean and inspect all parts. Replace worn or damaged parts with
new parts as required.
S Pumpsthatneed to be submersed must havebothwetandnon-wet
components compatible with the material being pumped.
S Submersed pumps must have exhaust pipe above liquid level. Ex-
haust hose must be conductive and grounded.
S Lubricate (1) diaphragm rod and (144) “U” cup with LubriplateR
FML-2 grease (94276 grease packet is included in service kit).
S FormodelswithPTFEdiaphragms:Item(8)Santoprenediaphragm
is installed with the side marked “AIR SIDE” towards the pump cen-
ter body. Install the PTFE diaphragm (7) with the side marked
“FLUID SIDE” towards the (15) fluid cap.
S Flooded suction inlet pressure must not exceed 10 p.s.i.g. (0.69
bar).
S Re-check torque settings after pump has been re-started and run a
while.
S HytrelR and VitonR are registered trademarks of the DuPont Company S KynarR is a registered trademark of Arkema Inc. S LoctiteR and 242R are registered trademarks of Henkel Loctite Corporation S
S SantopreneR is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. S LubriplateR is a registered trademark of Lubriplate Division (Fiske Brothers Refining Company) S
S AROR is a registered trademark of Ingersoll-Rand Company S 271t is a trademark of Henkel Loctite Corporation S
PD15X-XXX-XXX (en)
Page 3 of 8
PARTS LIST / PX15X-XXX-XXX FLUID SECTION
L 637375-XX FLUID SECTION SERVICE KITS INCLUDE: BALLS (see Ball Option, refer to -XX in Service Kit chart below), DIAPHRAGMS (see Diaphragm
Option, refer to -XX in Service Kit chart below), and items 19, 70, 144, 175 and 180 (listed below) plus 174 and 94276 Lubriplate FML-2 grease (page 6).
SEAT OPTIONS PX15X-XXX-XXX
“21”
BALL OPTIONS PX15X-XXX-XXX
L “22” (2” dia.)
-XXX Seat
Qty [Mtl]
(4) [Sp]
-XXX Seat
Qty [Mtl]
(4) [B]
(4) [SH]
(4) [Ha]
(4) [SS]
-XXX Ball
Qty [Mtl]
(4) [Sp]
-XXX Ball
Qty [Mtl]
(4) [SS]
-AXX 95825-A
-CXX 95825-C
-EXX 95893
-FXX 95892
-GXX 95825-G
-HXX 95891
-LXX 95947
-SXX 95877
-XAX 95826-A
-XCX 95826-C
-XGX 95826-2
-XSX 95878
-XTX 95826-4
-XVX 95826-3
(4)
(4)
(4)
[H]
[C]
[A]
(4)
(4)
[H]
[B]
(4)
(4)
[T]
[V]
MATERIAL CODE
[A] = Aluminum
[B] = Nitrile
[C] = Carbon Steel
[CI] = Cast Iron
[Co] = Copper
DIAPHRAGM OPTIONS PX15X-XXX-XXX
L Service Kit
-XX = (Ball)
-XXX -XX = (Diaphragm) Diaphragm Qty [Mtl] Diaphragm Qty [Mtl] Gasket
L “7”
L “8”
L “19” (1/8” x 3-1/8” o.d.)
Qty [Mtl]
[E] = E.P.R.
[H] = Hytrel
-XXA 637375-XA
-XXC 637375-XC
-XXG 637375-XG
-XXM 637375-XM
-XXT 637375-XT
-XXV 637375-XV
96166-A
96166-C
96166-G
96166-M
96165-T
95820-3
(2)
(2)
(2)
[Sp] - - - - -
- - -
- - -
- - -
- - -
- - - 95992
(4)
(4)
(4)
(4)
(4)
(4)
[E]
[V]
[B]
[T]
[T]
[V]
[Ha] = Hastelloy-C
[K] = KynarR PVDF
[MSp]=MedicalGradeSantoprene
[P] = Polypropylene
[SH] = Hard Stainless Steel
[Sp] = Santoprene
[SS] = Stainless Steel
[T] = PTFE
[V] = Viton
[H]
[B]
- - - - -
- - - - -
- - - Y327-233
- - - Y325-233
- - - Y328-233
(2) [MSp] - - - - -
(2)
(2)
[T]
[V]
96164-A
- - - - -
(2) [Sp] Y328-233
- - - - - - Y327-233
CENTER SECTION OPTIONS PX15X-XXX-XXX
PD15A-X
PE15A-X
Part No.
- - - - -
PD15R-X
[Mtl] Part No.
- - - 93360-1
[Co] - - - - -
[A] 95971-1
[A] 95971-2
[SS] - - - - -
[SS] - - - - -
[C] - - - - -
- - - 96056
[Co] - - - - -
- - - 96291
[SS] 94992
PE15R-X
Part No.
93360-1
- - - - -
95971-3
95971-4
93832-3
Y17-50-S
- - - - -
96056
- - - - -
96291
94992
PD15S-X
[Mtl] Part No.
PE15S-X
Part No.
- - - - -
Item
Description (size)
Qty Part No.
(4) - - - - -
(1) 93004
(1) 95822-1
(1) 95822-2
(2) - - - - -
(1) - - - - -
(4) 95934
(4) - - - - -
(4) 94098
(8) - - - - -
(4) 93010
[Mtl]
- - -
28 Washer (0.406” i.d. x 1” o.d. x 0.093”)
43 Ground Lug
[SS] - - - - -
- - - 93004
[P] 95889-1
[P] 95889-2
[K] - - - - -
[SS] - - - - -
- - - 96657
[SS] - - - - -
- - - 94098
[B] - - - - -
[SS] 93010
93004
93004
[Co]
[SS]
[SS]
[SS]
[SS]
[SS]
- - -
68 Air Cap
69 Air Cap
95822-3
95822-4
Y17-51-S
Y17-50-S
95934
- - - - -
94098
- - - - -
93010
95889-3
95889-4
Y17-51-S
Y17-50-S
96657
- - - - -
94098
- - - - -
93010
74 Pipe Plug (1/4 - 18 N.P.T. x 7/16”)
76 Pipe Plug (1/8 - 27 N.P.T. x 0.27”)
131 Screw (M10 x 1.5 - 6g x 100 mm)
(M10 x 1.5 - 6g x 110 mm)
n 180 Washer
[Co]
- - -
[SS]
L n “O” Ring (3 mm x 15 mm o.d.)
195 Nut (M10 x 1.5 - 6h)
MANIFOLD / FLUID CAP MATERIAL OPTIONS PX15X-XXX-XXX
PX15X-XAX-X
Qty Part No. [Mtl] Part No.
PX15X-XCX-X
PX15X-YHX-X
PX15X-XSX-X
PX15X-YSX-X
Item Description (size)
[Mtl] Part No.
[Mtl] Part No.
[Mtl] Part No.
[Mtl]
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
- - -
5
6
9
Backup Washer
Diaphragm Washer
Washer
(2) 95819-3
(2) 95819-3
(2) Y13-8-T
(2) 95883
[C] 95819-3
[C] 95819-3
[SS] Y13-8-T
[SS] 95883
[C] 95819-1
[C] 95819-2
[SS] 95993
[SS] 95952
[CI] 95949
[CI] 95954 s
[CI] 95956 s
[SS] - - - - -
[SS] - - - - -
[SS] 95819-1
[Ha] 95819-1
[Ha] Y13-8-T
[Ha] 95883
[SS] 95819-1
[SS] 95819-1
[SS] Y13-8-T
[SS] 95883
[SS] 95890
[SS] 95943 s
[SS] 95945 s
[SS] - - - - -
14 Screw (M14 x 2 - 6g x 45 mm)
15 Fluid Cap
(2) 95821
[A] 95953
[Ha] 95890
60 Inlet Manifold
(1) 95828-[z]
(1) 95827-[z]
(2) Y17-127
(2) 95902-2
[A] 95940-[z]
[A] 95937-[z]
[A] Y17-57-S
[A] 95902-1
[Ha] 95900-[z]
[Ha] 95899-[z]
- - - Y17-57-S
- - - 95902-1
61 Outlet Manifold
63 Pipe Plug (1-1/2 N.P.T.)
(R 1-1/2)
[SS] - - - - -
- - -
z For N.P.T.F. thread models (PX15X-AXX-XXX), use “-1”
z For BSP thread models (PX15X-BXX-XXX), use “-2”
s
Flange models
EXTERNAL HARDWARE OPTIONS PX15X-XXX-XXX
COMMON PARTS
PX15X-XXP- PX15S-XXS- PX15R-XXS-
Item
Description (size)
Rod
Qty Part No. Mtl
Item Description (size)
Qty Part No. Mtl Part No. Mtl Part No. Mtl
1
(1) 95824
(2) 95843
(2) Y186-50
[C]
[B]
[B]
[B]
26 Screw (M10 x 1.5 - 6g x 30 mm) (8) 95884-1 [C] 95884
[SS] 95884
[SS]
[SS]
L n 70 Gasket
27 Bolt (M8 x 1.25 - 6g x 40 mm)
(M8 x 1.25 - 6g x 50 mm)
(20) 95896-1 [C] 95896
(20)
Ln 144 “U” Cup (3/16” x 1-1/4” o.d.)
96163
[SS]
[SS]
Ln 175 “O” Ring (3/32” x 13/16” o.d.) (2) Y325-114
29 Hex Flange Nut (M8 x 1.25 - 6h) (20) 95879-1 [C] 95879
n Items included in air section service kit, see page 6.
Page 4 of 8
[SS] 95879
PD15X-XXX-XXX (en)
PARTS LIST / PX15X-XXX-XXX FLUID SECTION
View of two piece PTFE diaphragm
COLOR CODE
DIAPHRAGM
COLOR
3
2
1
4
BALL
COLOR
5
7
8
6
MATERIAL
Hytrel
Nitrile
Cream
Black
Tan
Cream
Red (S)
Tan
Santoprene
Santoprene
(Backup)
PTFE
9
10
Green
N / A
White
Yellow (-)
(-) Dash
White
Yellow (S)
(S) Dot
Viton
-
Santoprene 8
PTFE 7
Torque Sequence
61 (models PX15X-YXX-XXX)
61 (models PX15X-AXX-XXX
and PX15X-BXX-XXX)
26 , U
FOR THE
AIR MOTOR SECTION
SEE PAGES 6 & 7
Figure 2
70 k 76 -
68
144 k
70 k 27 U 195
A
69
7
9
22
21
B
B
19 Y
29 ,
15
A
175 k 144 k 43
74 -
175 k
1 k
26 , U
22
180 k 131 ,x
63 -
5
6
14 , ~
21
60 (models PX15X-AXX-XXX
and PX15X-BXX-XXX)
19 Y
60 (models PX15X-YXX-XXX)
. TORQUE REQUIREMENTS ,
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
(14) screw, tighten to 50 - 55 ft lbs (67.8 - 74.6 Nm).
(26) screws, 20 - 25 ft lbs (27.1 - 33.9 Nm).
(29) nuts, 15 - 20 ft lbs (20.3 - 27.1 Nm).
AUXILIARY VIEW A-A
(models PX15R-XXX-XXX)
AUXILIARY VIEW B-B
(models PX15R-XXX-XXX)
(131) screws, 12 - 17 ft lbs (16.3 - 23.0 Nm).
LUBRICATION / SEALANTS
k 180
28
180 k
k Apply Lubriplate FML-2 grease to all “O” rings, “U” Cups & mating
parts.
x Apply LoctiteR 242R to threads at assembly.
- Apply PTFE tape to threads at assembly.
~ Apply Loctite 271t to threads at assembly.
195
U
Apply anti-seize compound to threads and bolt and nut flange heads
which contact pump case when using stainless steel fasteners.
Not used with PX15X-XXX-AXX, -CXX and -GXX.
Y
Z Lubriplate FML-2 is a white food grade petroleum grease.
PD15X-XXX-XXX (en)
Page 5 of 8
PARTS LIST / PX15X-XXX-XXX AIR SECTION
n Indicates parts included in 637389 Air Section Service Kit shown below and items (70), (144), (175) and (180) shown on page 4.
AIR MOTOR PARTS
Item
Description (size)
Qty Part No.
(1) 95888
(1) 95970
(1) 95901
(1) 95823
[Mtl]
[A]
Item
Description (size)
Qty Part No.
(1) 95941
(1) 95833
(1) 95938
(1) 95844
(1) Y186-53
(1) Y186-49
(1) 95838
(1) 95837
(1) 96171
(1) 67164
(2) 94433
(1) Y240-9
(1) 94081
(1) Y325-119
(1) Y325-22
(2) Y325-123
(2) Y325-202
(2) 95845
(4) Y178-52-S
(1) 96172
(1) 95842
(1) 93139
(1) 350-568
(1) 95832
(4) 95924
(1) 94276
637308
[Mtl]
[Z]
[P]
[SS]
[B]
[B]
101 Center Body (PX15A-X)
(PX15R-X)
136 End Cap (PX15A-X)
(PX15R-X)
[P]
(PX15S-X)
[SS]
[D]
(PX15S-X)
103 Bushing
105 Screw (M6 x 1 - 6g)
n 137 Gasket
n 138 “U” Cup (3/16” x 1-5/8” o.d.)
n 139 “U” Cup (3/16” x 1-1/8” o.d.)
140 Valve Insert
141 Valve Plate
n 166 Gasket
(PX15A-X and PX15S-X) (16 mm long) (4) 95991
[SS]
[SS]
[SS]
[D]
[B]
(PX15R-X) (130 mm long)
107 End Plate (PX15R-X only)
111 Spool (PX15A-X and PX15S-X)
(PX15R-X)
(4) 95886
(2) 95840
(1) 95835
(1) 96293
(2) 95839
(2) 95123
(1) Y17-50-S
[AO]
[AO]
[B]
[D]
[U]
[B]
[Br]
[B]
[B]
[B]
[D]
[SS]
[D]
n 167 Pilot Piston (includes 168 and 169)
168 “O” Ring (3/32” x 5/8” o.d.)
169 “U” Cup (1/8” x 7/8” o.d.)
170 Piston Sleeve
118 Actuator Pin
121 Sleeve
128 Pipe Plug (1/8 - 27 N.P.T. x 0.27”)
(PX15A-X and PX15S-X only)
[SS]
n 171 “O” Ring (3/32” x 1-1/8” o.d.)
n 172 “O” Ring (1/16” x 1-1/8” o.d.)
n 173 “O” Ring (3/32” x 1-3/8” o.d.)
K n 174 “O” Ring (1/8” x 1/2” o.d.)
n 176 Diaphragm (check valve)
181 Roll Pin (5/32” o.d. x 1/2” long)
n 200 Gasket (PX15A-X and PX15S-X)
(PX15R-X)
n 132 Gasket
133 Washer (1/4”) (PX15A-X)
(M6) (PX15R-X)
(1) 96170
[B]
[C]
(3) Y117-416-C
(6) 95931
[B]
[SS]
[SS]
[SS]
[SS]
[Z]
[SP]
[SS]
[B]
[B]
[P]
- - -
[P]
[SS]
(1/4”) (PX15S-X)
(3) Y14-416-T
134 Screw (M6 x 1 - 6g x 20 mm) (PX15R-X) (6) 95887
(PX15A-X and PX15S-X)
(4) 95887
135 Valve Block (PD15A-X)
(1) 95942-1
(1) 95834-1
(1) 95939-1
(1) 95942-2
(1) 95834-2
(1) 95939-2
201 Muffler (PX15R-X)
(PD15R-X)
(PD15S-X)
(PE15A-X)
(PE15R-X)
(PE15S-X)
[P]
(PX15A-X and PX15S-X)
[SS]
[Z]
233 Adapter Plate
236 Nut (M6 x 1 - 6g) (PX15R-X only)
L n Lubriplate FML-2 Grease
Lubriplate Grease Packets (10)
[P]
[SS]
K
Items included in fluid section service kit, see page 4.
AIR MOTOR SECTION SERVICE
MAJOR VALVE DISASSEMBLY
Service is divided into two parts - 1. Pilot Valve, 2. Major Valve.
GENERAL REASSEMBLY NOTES:
1. Remove (135) valve block and (233) adapter plate, exposing (132 and
166) gaskets and (176) checks.
S
S
Air Motor Section Service is continued from Fluid Section repair.
Inspect and replace old parts with new parts as necessary. Look for
deep scratches on surfaces, and nicks or cuts in “O” rings.
Take precautions to prevent cutting “O” rings upon installation.
Lubricate “O” rings with Lubriplate FML-2 grease.
2. Insert a small flat blade screwdriver into the notch in the side of (135)
valve block and push in on tab to remove (233) adapter plate, releasing
(140) valve insert, (141) valve plate, (200) gasket.
S
S
S
3. Remove (136) end cap and (137) gasket, releasing (111) spool.
Do not over-tighten fasteners, refer to torque specification block on
view.
MAJOR VALVE REASSEMBLY
S
S
Re-torque fasteners following restart.
1. Install new (138 and 139) “U” cups on (111) spool -- LIPS MUST FACE
EACH OTHER.
2. Insert (111) spool into (135) valve block.
SERVICE TOOLS -- To aid in the installation of (168) “O” rings onto the
(167) pilot piston, use tool # 204130-T, available from ARO.
3. Install (137) gasket on (136) end cap and assemble end cap to (135)
valve block, securing with (107) end plates (where applicable) and
(105) screws.
4. Install (140) valve insert and (141) valve plate into (135) valve block.
NOTE: Assemble (140) valve insert with “dished” side toward (141)
valve plate. Assemble (141) valve plate with part number identification
toward (140) valve insert.
PILOT VALVE DISASSEMBLY
1. A light tap on (118) should expose the opposite (121)sleeve, (167)pilot
piston and other parts.
2. Remove (170) sleeve, inspect inner bore of sleeve for damage.
5. Assemble (200) gasket and (233) adapter plate to (135) valve block.
NOTE: Assemble (233) adapter plate with notched side down.
6. Assemble (132 and 166) gaskets and (176) checks to (101) body.
7. Assemble (135) valve block and components to (101) body, securing
with (134) screws.
PILOT VALVE REASSEMBLY
1. Clean and lubricate parts not being replaced from service kit.
2. Install new (171 and 172) “O” rings, replace (170) sleeve.
3. Install new (168) “O” rings and (169) seal - Note the lip direction. Lubri-
cate and replace (167).
4. Reassemble remaining parts, replace (173 and 174) “O” rings.
Page 6 of 8
PD15X-XXX-XXX (en)
PARTS LIST / PX15X-XXX-XXX AIR SECTION
173 k
118
169 k 168 k
PILOT VALVE
PART GROUP
172 k
171 k
170
k 174
121
173 k
121
167
118
166 k
174 k
233
140
141 k
133
135
U . 134
Notch
k 138
200 k
132 k 176 k 101 181 103
201
111
k 139
Insert screwdriver here to remove (233) adapter plate.
k 137
MAJOR
VALVE
- 128
136
MATERIAL CODE
[A] = Aluminum
[AO] = Alumina Oxide
[B] = Nitrile
U . 105
Figure 3
[Br] = Brass
[C] = Carbon Steel
[D] = Acetal
[P] = Polypropylene
[SP] = Santoprene
[SS] = Stainless Steel
[U] = Polyurethane
[Z] = Zinc
Models PX15A-XXX-XXX
PX15S-XXX-XXX
Models PX15R-XXX-XXX
Insert screwdriver here to remove (233) adapter plate.
107
. TORQUE REQUIREMENTS ,
U 105
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
133
U . 134
135
PX15A-XXX-XXX and PX15S-XXX-XXX: Torque (105 and 134) screws to 40 - 50
in. lbs (4.5 - 5.6 Nm).
PX15R-XXX-XXX: Torque (134) screw to 30 - 40 in. lbs (3.4 - 4.5 Nm) and (236)
nut to 35 - 40 in. lbs (4.0 - 4.5 Nm).
LUBRICATION / SEALANTS
k 138
k
Apply Lubriplate FML-2 grease to “O” rings, “U” Cups & mating parts.
- Apply PTFE tape to threads at assembly.
Apply anti-seize compound to threads at assembly.
U
111
A replacement Major Valve Service Assembly is available separately, which includes the following:
637390-1 for models PD15R-XXX-XXX: 105 (4), 107 (2), 111, 132, 135, 136, 137, 138, 139, 140,
141, 166, 176 (2), 200, 233 and 236 (4).
637390-2formodelsPE15R-XXX-XXX:76,105(4),107(2),111,132,135,136,137,138,139,140,
141, 166, 176 (2), 200, 233 and 236 (4).
637390-3 for models PD15A-XXX-XXX: 105 (4), 111, 128, 132, 135, 136, 137, 138, 139, 140, 141,
166, 176 (2), 200 and 233.
k 139
k 137
136
637390-4 for models PE15A-XXX-XXX: 76, 105 (4), 111, 128, 132, 135, 136, 137, 138, 139, 140,
141, 166, 176 (2), 200 and 233.
637390-5 for models PD15S-XXX-XXX: 105 (4), 111, 128, 132, 135, 136, 137, 138, 139, 140, 141,
166, 176 (2), 200 and 233.
637390-6 for models PE15S-XXX-XXX: 76, 105 (4), 111, 128, 132, 135, 136, 137, 138, 139, 140,
141, 166, 176 (2), 200 and 233.
107
. 236
PD15X-XXX-XXX (en)
Page 7 of 8
TROUBLE SHOOTING
Product discharged from exhaust outlet.
S Check for diaphragm rupture.
S Check tightness of (14) diaphragm screw.
Low output volume, erratic flow, or no flow.
S Check air supply.
S Check for plugged outlet hose.
S Check for kinked (restrictive) outlet material hose.
S Check for kinked (restrictive) or collapsed inlet material hose.
S Check for pump cavitation -- suction pipe should be sized at least as
large as the inlet thread diameter of the pump for proper flow if high
viscosity fluids are being pumped. Suction hose must be a non-col-
lapsing type, capable of pulling a high vacuum.
S Check all joints on the inlet manifolds and suction connections.
These must be air tight.
Air bubbles in product discharge.
S Check connections of suction plumbing.
S Check “O” rings between intake manifold and inlet side fluid caps.
S Check tightness of (14) diaphragm screw.
Motor blows air or stalls.
S Check (176) check valve for damage or wear.
S Check for restrictions in valve / exhaust.
S Inspectthepumpforsolidobjectslodgedinthediaphragmchamber
or the seat area.
DIMENSIONAL DATA
(Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).
Air Inlet 1/2 - 14 N.P.T.
1-1/2 - 11-1/2 N.P.T.F. - 1 (PX15X-AXX-XXX)
Rp 1-1/2 (1-1/2 - 11 BSP) (PX15X-BXX-XXX)
Exhaust Port 3/4 - 14 N.P.T.
T
1-1/2” A.N.S.I. / DIN Flange
(PX15X-YXX-XXX)
A
E
F
L
L
Q
P
Outlet
R
B
B
G
N
D
D
Inlet
K
S
H
J
C
L
M
C
1-1/2 - 11-1/2 N.P.T.F. - 1 (PX15X-AXX-XXX)
Rp 1-1/2 (1-1/2 - 11 BSP) (PX15X-BXX-XXX)
DIMENSIONS
A - see below
F - 10-1/4” (260.4 mm)
G - 19-5/8” (498.1 mm)
H - 9” (228.6 mm)
J - 10” (254.0 mm)
K - 1/2” (12.7 mm)
L - see below
R - 21-7/16” (543.9 mm)
S - see below
T - see below
B - 18-3/8” (466.7 mm)
C - 11-3/4” (298.5 mm)
D - 2-3/4” (69.9 mm)
E - see below
M - 1/4” (6.4 mm)
N - 9-11/16” (246.0 mm)
P - see below
Q - see below
“A”
“L”
“P”
“Q”
“S”
PX15X-XAX-XXX
PX15X-XCX-XXX
PX15X-XHX-XXX
14-7/8” (377.8 mm)
14-5/8” (371.5 mm)
14-9/16” (370.0 mm)
1-3/4” (44.5 mm)
1-3/4” (44.5 mm)
3-1/8” (79.4 mm)
1-3/4” (44.5 mm)
3-1/8” (79.4 mm)
7-7/32” (183.4 mm)
7-3/16” (182.6 mm)
7-3/16” (182.6 mm)
7-9/32” (185.0 mm)
7-9/32” (185.0 mm)
14-23/32” (373.9 mm)
14-1/2” (368.3 mm)
14-1/2” (368.3 mm)
14-13/16” (375.5 mm)
14-9/16” (370.0 mm)
1/2” (12.7 mm)
1/4” (6.4 mm)
1/4” (6.4 mm)
15/32” (11.4 mm)
15/32” (11.4 mm)
PX15X-ASX-XXX, -BSX 14-25/32” (375.5 mm)
PX15X-YSX-XXX 14-9/16” (370.0 mm)
“E”
“T”
PX15A-XXX-XXX
N / A
14-1/32” (356.2 mm)
N / A
PX15R-XXX-XXX 11-3/32” (281.3 mm)
PX15S-XXX-XXX
N / A
13-7/8” (352.4 mm)
Figure 4
PN 97999-1056
Page 8 of 8
PD15X-XXX-XXX (en)
|