Ingersoll Rand Heat Pump LM2203A X C User Manual

OPERATOR’S MANUAL  
LM2203A-X-C  
INCLUDING: SPECIFICATIONS, SERVICE KITS, GENERAL INFORMATION, PARTS, TROUBLESHOOTING  
RELEASED: 12-27-04  
INCLUDE MANUAL:S-632GENERAL INFORMATION (PN 97999-  
624)  
REVISED:  
9-22-11  
(REV. 03)  
2” AIR MOTOR  
3:1 RATIO  
0 - 450 P.S.I. RANGE  
LM2203A-XX-C  
TWO-BALLPUMP SERIES  
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,  
OPERATING OR SERVICING THIS EQUIPMENT.  
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.  
SERVICE KITS  
PUMP DATA  
Use only genuine AROR replacement parts to assure compatible  
pressure rating and longest service life.  
MODEL LM2203A-XX-C  
637224 Pump Rebuild Kit. Includes the necessary soft parts for  
normal service of the entire pump.  
Air Inlet (female)  
See “Specifications”  
SPECIFICATIONS  
1-5/16”  
(33.4 mm)  
Model Series (refer to option chart) . . . . . . . . LM2203A-XX-C  
Type . . . . . . . . . . . . . . . . . . . . . . . . . Air Operated, Two Ball,  
Double Acting Oil Pump  
Material Outlet (female)  
See “Specifications”  
Ratio . . . . . . . . . . . . . . . . . . . . . . . . . 3:1  
Air Motor Diameter . . . . . . . . . . . . . . 2’’ (5.08 cm)  
Stroke . . . . . . . . . . . . . . . . . . . . . . 3’’ (7.62 cm)  
Air Inlet (female)  
18-1/32”  
(458.0 mm)  
2” NPT BUNG ADAPTER  
6-29/32”  
(175.2 mm)  
LM2203A-X1-C . . . . . . . . . . . . . . 1/4 - 18 N.P.T.F.  
LM2203A-X2-C . . . . . . . . . . . Rp 1/4 (1/4 - 19 BSP Parallel)  
Material Inlet (female)  
Material Inlet (female)  
(LM2203A-1X-C)  
See “Specifications”  
LM2203A-X1-C . . . . . . . . . . . . . . 3/4 - 14 N.P.T.  
LM2203A-X2-C . . . . . . . . . . . Rp 3/4 (3/4 - 14 BSP Parallel)  
Material Outlet (female)  
LM2203A-X1-C . . . . . . . . . . . . . . 1/2 - 14 N.P.T.F. - 1  
LM2203A-X2-C . . . . . . . . . . . Rp 1/2 (1/2 - 14 BSP Parallel)  
Pump Construction . . . . . . . . . . . . Carbon Steel  
Dimensional Data . . . . . . . . . . . . . . . See chart  
Weight . . . . . . . . . . . . . . . . . . . . . . . . See chart  
“B”  
“A”  
Figure 1  
PERFORMANCE  
Air Inlet Pressure Range . . . . . . . . . . 0 - 150 p.s.i. (0 - 10.3 bar)  
Fluid Pressure Range . . . . . . . . . . . . 0 - 450 p.s.i. (0 - 31.0 bar)  
Maximum Rec’d Cycles / Minute . . . . 125  
Material Inlet (female)  
(LM2203A-3X-C, -4X-C, -5X-C)  
See “Specifications”  
Displacement In3 Per Cycle . . . . . . . . 6.2  
NOTE: Dimensions are shown in inches and (mm), supplied for reference only and are typically  
rounded up to the nearest 1/16 inch.  
Volume / Cycle . . . . . . . . . . . . . . . . . . 3.46 oz. (102.28 ml)  
Cycles Per Gallon (Liter) . . . . . . . . . . 37 (9.8)  
Maximum Working Flow Rate . . . . . . 6 g.p.m. (23 l.p.m.)  
Maximum Flow Rate . . . . . . . . . . . . . 9 g.p.m. (34 l.p.m.)  
Noise Level @ 100 p.s.i. - 124 c.p.m. . 80 db(A)*  
Accessories Available . . . . . . . . . . . . 61113 Wall Mount Bracket  
66073-1 Air Line Connection Kit  
MODEL  
“A” (mm)  
“B” (mm)  
N / A  
WEIGHT (kg)  
11 (4.99)  
13.5 (6.12)  
14.4 (6.53)  
15 (6.80)  
LM2203A-1X-C  
N / A  
LM2203A-3X-C 40-1/16” (1017.6)  
22-1/32” (559.3)  
LM2203A-4X-C 49-13/16” (1265.0) 31-25/32” (806.9)  
LM2203A-5X-C 57-7/16” (1458.6) 39-13/32” (1000.6)  
IMPORTANT  
*
ThepumpsoundpressurelevelhasbeenupdatedtoanEquivalentContinuousSound  
This is one of two documents which support the pump. Replace-  
ment copies of these forms are available upon request.  
= LM2203A-X-C Model Operator’s Manual  
Level (L ) to meet the intent of ANSI S1. 13-1971, CAGI-PNEUROP S5.1 using four  
Aeq  
microphone locations.  
- S-632 General Information Lubrication Piston Pumps  
PATENTED  
INGERSOLL RAND COMPANY  
209 NORTH MAIN STREET BRYAN, OHIO 43506  
(800) 495--0276 D FAX (800) 892--6276  
E2011  
CCN 15237365  
 
PARTS LIST / LM2203A-XX-C  
1
6
7
19  
20  
21  
22  
2
3
8
9
4
5
23  
24  
25  
10  
UPPER SECTION  
LOWER SECTION  
11  
34  
35  
26  
38  
27 ,  
28 H  
. 36  
H
37  
29 ,  
5
4
9
8
30  
12  
48  
13  
31  
7
6
32  
33 ,  
14  
13  
3
41  
42  
15  
16  
17  
43  
44  
47  
18  
45  
46  
H Lubricate with Gadus S2 U1000 grease at assembly.  
. TORQUE REQUIREMENTS ,  
(27) 80 in. lbs (9 Nm).  
(29, 33) 95 - 100 ft lbs (128.8 - 135.6 Nm).  
49  
39  
40  
(36) 80 in. lbs (9 Nm) maximum.  
Figure 2  
LM2203A-X-C  
Page 3 of 4  
 
PLACING INTO SERVICE  
AIR AND LUBRICATION REQUIREMENTS  
should be used on thread connection. Tighten all fittings. Use cau-  
tion not to damage threads.  
Filtered air willhelpextendthelife of thepump, allowingthepump to op-  
erate more efficiently and yield longer service life to moving parts and  
mechanisms.  
OPERATION  
Installanairlinefiltertoprovidegoodqualitycleananddryair.Install  
it up stream from the regulator.  
START-UP  
Use an air regulator on the air supply to control the pump cycle rate.  
Install the regulator as close as possible to the pump.  
Inmostinstallations, lubricationisnotrequired. Ifthepumpneedsto  
havelubrication,installanairlinelubricatorandsupplyitwithagood  
grade of non-detergent oil or other lubricant compatible with Nitrile  
seals and set at a rate not to exceed one drop per minute.  
1. Turn the air regulator to “0” pressure setting.  
2. Immerse the lower pump end into the material.  
3. Open the dispensing device.  
4. Start the pump cycling slowlyby raisingthe pressureto 20 - 30p.s.i.  
(1.4 - 2.1 bar).  
5. Close the dispensing device. Allow the pump to stall and build line  
pressure. Check for anyleaks and tighten fittingsas needed. Adjust  
pressure as required for the application.  
INSTALLATION  
Mount and secure the pump as required for the application.  
Attach a ground wire from the pump ground screw to a suitable  
ground.  
SHUTDOWN  
Disconnecttheairsupplyfromthepumpifitistobeinactiveforafew  
Connectafluidhosetothepumpoutlet.Inmostcasesapipesealant  
hours. Open the dispensing device to relieve line pressure.  
SERVICE  
2. Locate the valve chamber on the (11) cylinder where the 3/8’’ dia.  
hole is located and install one of the (4) sleeves. Insert the (7) spool  
from the opposite end. Next, install the remaining sleeve and spool.  
3. Replace the (3) track gasket and install (2) cap.  
PUMP DISASSEMBLY / REASSEMBLY  
NOTICE: The unique design of this pump allows for quick basic pump  
service without total removal from the drum (refer to the views below).  
DISASSEMBLY - Allthreadsarerighthand.Refertofigure2.These  
proceduresarefortheinstallationofrepairkitparts.Disconnectair  
supply and relieve all system pressure prior to servicing. Carefully  
removetheparts,inspectpartsfordamage,nicksorexcessivewearand  
determine if any parts will need replacement.  
4. Replacethe(13) pistonU” cups(refer tofigure 2for proper orienta-  
tion). Replacethe(19) “O” ringandassemble(14) pistonto (20)pis-  
ton rod and retain with (48) washer and (12) retaining ring.  
5. Install the (20, 14) piston assembly using great care to collapse the  
outer lip of the second “U” cup, allowing it to slip into the cylinder.  
6. Replace the (3) track gasket and install the (15) cap. Install the (16)  
“O” ring onto the piston rod, replace (17) bushing and (18) packing.  
7. Replace the (25) “O” ring and re-attach the (24) inner check.  
8. Slide the pump assembly back into the (26) base / lower pump sec-  
tion.Pressthesectionstogetherandaligntheairinletandpumpout-  
letasrequiredandreplacethefour(1)boltsand(27)nuts(tightento  
80 in. lbs (9 Nm).  
Follow the three disassembly steps in the detail views below and place  
the pump on a clean bench.  
1. Remove(1) bolts. Remove(18)packing, (17)bushingand(16) “Oring.  
2. Remove (36) adapter, releasing (10) muffler housing.  
3. Grasp the (11) cylinder and remove the (20, 14) piston assembly.  
4. Remove (15) lower cap and (3) trackgasket. Remove (12) retaining  
ring and (48) washer, then pull (14) piston off (20) piston rod.  
5. Remove (2) cap and (3) track gasket. Push on the large o.d. end of  
the(7)spooltoremovethe(4)sleeve.Grabthenoseof(7)spooland  
pull out. Repeat for other sleeve and spool.  
TROUBLE SHOOTING  
If the pump will not cycle or will not deliver material.  
Becertaintocheckfornon-pumpproblemsincludingkinked,restric-  
tiveorpluggedinlet/outlethoseordispensingdevice.Depressurize  
the pump system and clean out any obstructions in the inlet / outlet  
material lines.  
REASSEMBLY - Thoroughly clean and lubricate all seals and  
bores with Shell Gadus S2 U1000 upon assembly. Replace all soft  
parts with new ones included in the repair kit.  
Note: Refer to the illustration (figure 2) for “U” cup lip seal direction.  
1. Replace the seals on both the (7) spools and (4) sleeves.  
Check all seals, including track gaskets.  
Check direction of “U” cup lips.  
PUMP DISASSEMBLY DETAIL  
A) Remove the four  
nuts from the base  
of the Air Motor.  
B) Grasp the lower motor cap  
and pull out the motor and  
upper section of the lower  
section.  
C) Unlock the (24) inner  
check from the piston  
rod.  
Figure 3  
Figure 4  
Figure 5  
PN 97999-1132  
LM2203A-X-C  
Page 4 of 4  
 

Init TV Video Accessories NT TVM102 User Manual
Jet Tools Saw VBS 2012 User Manual
JL Audio Car Speaker SB T 4RNR 10W User Manual
JL Audio Car Stereo System C2 075ct User Manual
John Deere Lawn Mower JS26 User Manual
Jonsered Trimmer HT 2124 User Manual
JVC CD Player KD ADV7490 User Manual
Kambrook Fan KFA413B User Manual
Kenwood Microwave Oven MW761E User Manual
Kenwood Mixer HM790 User Manual