SECTION
MANUAL
M107
15
OPERATOR’S MANUAL
INCLUDING:ĂOPERATION,ĂINSTALLATIONĂ&ĂMAINTENANCE
SERIES 34 ELECTRA–FEED DRILL
Released: 6-1-93
Revised: 11-20-99
49999-447
R
Models FE034A–( )–A( )
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
OPERATING AND SAFETY PRECAUTIONS
AIR SUPPLY REQUIREMENTS
•
Keep hands and clothing away from rotating end of tool and all
moving parts of the tool.
For maximum operating efficiency, the following air supply specifi-
cations should be maintained to this air tool:
•
•
Wear suitable eye protection while operating tool or when
near tool when it is being operated.
Disconnect air and electrical supply from tool before remov-
ing/installing bits or performing other maintenance or service
procedures.
•
•
•
AIR PRESSURE – 90 PSIG (6 bar)
AIR FILTRATION – 50 micron
HOSE SIZE – 5/16” (8 mm) I.D.
An AROR model P29231–110 air line FILTER/REGULATOR plus
100067 gauge is recommended to maintain the above air supply
specifications.
ROUTINE LUBRICATION REQUIREMENTS
When this tool was built, an “O” ring lubricant was applied to all ap-
propriate dynamic seals to insure continued operation. Drive train
components and bearings were also supplied / filled with grease
to insure appropriate life of components. As long as all exterior
seals and wipers are maintained in good working order and all
covers and breather vents are kept in place, it is reasonable to ex-
pect that external debris will not enter the tool. It is also reason-
able to expect that lubricants applied to the tool interior will require
replenishment for at least 5000 hours of normal operation.
Adding spindle oil to the power air inlet of this tool is not
necessary.
RECOMMENDED LUBRICANTS
After disassembly is complete, all parts, except sealed or shielded
bearings, should be washed with solvent. To relubricate parts, or
for routine lubrication, use the following recommended lubricants:
Where Used
ARO Part #
Description
‘‘O” Rings, Lip Seals
and Air Cylinder
36460
4 oz. Stringy Lubricant
Sliding Splines and
Bearings
33153
5 lb. ‘‘EP” – NLGI #1
Grease
MOUNTING
Mounting clamps 49690 and 46982–1 are available for mounting
of this tool. These items are shown on page 11. Both mounts allow
the clamp to grip the outer sleeve of the tool and feature keyways
for alignment.
For parts and service information, contact your local ARO distributor, or the Customer Service Dept. of the Ingersoll–Rand Distribution
Center, White House, TN at PH: (615) 672–0321, FAX: (615) 672–0801.
ARO Tool Products
Ingersoll–Rand Company
1725 U.S. No. 1 North D P.O. Box 8000 D Southern Pines, NC 28388–8000
E1999 INGERSOLL–RAND COMPANYD PRINTED IN U.S.A.
M107
INSTALLATION
15
The ARO model FE034A–( ) is NOT supplied with the required
motor starter. The motor starter must conform to the local/national
regulations governing the use of this type of electrical equipment
and must provide motor overload protection. The recommended
overload setting is given on the wiring diagram. The power supply,
motor starter and the motor nameplate ratings must be equiva-
lent.
Connect the motor starter to the motor as shown in the wiring dia-
gram. The minimum wire size should be AWG No. 14, or equiva-
lent, (4107 circular mil) and conform to local/national regulations
governing the use of this type of electrical equipment.
Once the motor is connected, turn on the power supply. If the
spindle fails to rotate or rotates in the wrong direction, de–ener-
gize the motor starter immediately. Turn off the power supply and
recheck the wiring.
MOTOR: The electric motor develops a minimum of .33 horse-
power. The voltage requirements are shown below in the Electri-
cal Connection Diagram.
SET–UP PROCEDURE
WARNING: Keep clear of rotating end of unit with hands and/or
clothing.
ELECTRICAL CONNECTION DIAGRAM
3 PHASE, 60 Hz
•
•
•
Shut off air supply to tool.
Loosen screw (41), releasing cover (33).
Determine the TOTAL STROKE LENGTH the drill must travel
to perform the drilling operation.
6
5
4
6
5
4
8
8
9
7
9
7
•
Loosen cap screw (28) securing yoke assembly (27) to quill
(55) and position yoke assembly on quill approximately 5/8”
(16 mm) greater distance between control valve (39) and yoke
assembly than the distance of the Total Stroke Length.
Tighten cap screw (28), securing yoke assembly (27) to quill
(55).
Loosen nut (29), securing cap screw (30) and turn cap screw
(30) so the distance between the head of the cap screw (30)
and control valve (39) equals the total stroke length.
Tighten nut (29), securing cap screw (30).
3
2
1
3
2
1
•
•
SUPPLY 230 V
*(60 Hz 1.6 – 2.0 amp.)
SUPPLY 460 V
*(60 Hz .8 – 1.0 amp.)
•
•
•
Replace cover (33), securing with screw (41).
Attach air supply to tool.
* RECOMMENDED OVERLOAD SETTING.
TO REVERSE ROTATION: INTERCHANGE ANY TWO LEADS.
FEED RATE CONTROL VALVES
WARNING: BE SURE THE ELECTRICAL POWER SUPPLY IS
OFF BEFORE MAKING ANY ELECTRICAL WIRING CONNEC-
TIONS.
•
Turn valve (103), marked ‘‘R” at side of control assembly (93),
approximately 1–1/2 turns counter–clockwise (open) from the
closed position.
Turn the other valve (103), marked ‘‘F” at side of control as-
sembly (93), clockwise until closed (do not tighten too snugly).
Start the unit and slowly turn valve (103) marked ‘‘F” counter–
clockwise (open) until the desired forward rate of feed is
reached.
•
•
WARNING: FAILURE TO PROPERLY GROUND THE MOTOR
MAY CAUSE SERIOUS INJURY TO PERSONNEL.
DO NOT BLOCK THE AIR FLOW TO OR FROM THE MOTOR
COOLING FAN. DO NOT DAMAGE THE MOTOR FAN COVER.
KEEP SMALL OBJECTS CLEAR OF THE OPENINGS IN THE
FAN COVER.
•
A final adjustment of the rate of return (retract) can be made
with the valve (103) marked ‘‘R”.
DISASSEMBLY/ASSEMBLY INSTRUCTIONS
•
•
Disconnect air and electrical supply ‘‘BEFORE” performing
maintenance or service to tool.
Never apply excessive pressure by a holding device which
may cause distortion of a part.
Apply pressure evenly to parts which have a press fit.
Apply even pressure to the bearing race that will be press
fitted to the mating part.
Use correct tools and fixtures when servicing this tool.
Don’t damage ‘‘O” rings when servicing this tool.
Use only genuine ARO replacement parts for this tool. When
ordering, specify part number, description, tool model number
and serial number.
_
To disassemble, remove retaining ring (14), releasing spring
washer (15), bearings (16) and tension wheel (17).
BELT AND PULLEY SECTION ASSEMBLY
•
•
_
_
Apply thread adhesive (Loctite 242) to threads of tension
wheel pin (18) and assemble to bracket (19).
Assemble bearing (16), tension wheel (17) and bearing (16) to
tension wheel pin (18), securing with spring washer (15) and
retaining ring (14).
Assemble tensioner assembly to housing (10), securing with
cap screw (13). Do not tighten cap screw.
Assemble motor (11) to housing (10), securing with four cap
screws (9).
Assemble keys (6) and pulleys (7 and 12) to spindle (23) and
motor spindle.
Apply thread adhesive (Loctite 290) to threads of cap screws
(4) and assemble screws and washers (5) to spindles, secur-
ing pulleys. NOTE: Tighten screws (4) to 50 – 60 in. lbs.
Assemble belt (3) over pulleys (7 and 12) and inside belt ten-
sioner.
•
•
•
_
_
_
_
BELT AND PULLEY SECTION DISASSEMBLY
_
Remove four screws (1), releasing cover (2).
Loosen cap screw (13), loosening tensioner assembly.
Remove belt (3).
Remove cap screws (4) and washers (5), releasing pulleys (7
and 12) and keys (6).
To remove motor (11), remove four cap screws (9).
Remove cap screw (13), releasing tensioner assembly.
_
_
_
_
_
_
_
Hold tensioner assembly firmly against belt (3) and secure by
tightening cap screw (13).
3
DISASSEMBLY/ASSEMBLY INSTRUCTIONS
_
Assemble cover (2) to housing, securing with four screws (1).
_
Refer to ‘‘Pulley Spindle Section” to assemble housing (10) to
frame assembly (35).
_
Grease wiper (67) with ARO 36460 lube and assemble to
groove in front bushing of outer sleeve assembly (64), with lips
of wiper facing towards sleeve (64).
PULLEY SPINDLE SECTION DISASSEMBLY
_
Follow instructions for disassembly of BELT AND PULLEY
SECTION and remove belt (3) and pulley (12).
Remove four cap screws (20) and separate drive housing (10)
from frame assembly (35). NOTE: Housings will have to be
pulled apart approximately 11” (279 mm) to completely sepa-
rate pulley spindle (23) from frame assembly (35).
Using a spanner type wrench, unthread and remove lock
screw (25).
_
_
Grease wipers (54) with ARO 36460 lube and assemble to
grooves in quill (55), with lips of wipers facing away from each
other.
Assemble spring washer (53) and plate (52) to quill (55), se-
curing with plate nut (51).
_
_
_
_
Assemble square seal (50) to quill (55).
Assemble bearing (56) to spindle (58), pressing on inner race
of bearing.
_
_
Pull spindle (23) and components from housing (10).
NOTE: Bearings (21) are press fit on spindle (23). Do not re-
move unless it should become necessary to replace, as Brin-
elling of the bearing races may occur, making replacement
necessary.
_
_
Assemble spindle (58) and spacer (57) into quill (55).
Pack bearings (59) with ARO 33153 grease and assemble
onto spindle (58) and into quill (55). NOTE: Assemble bear-
ings with open faces together (shielded sides facing out).
Assemble wiper (61) to groove in bearing stop (60), assem-
bling with lip of wiper toward the ‘‘chuck” end of the tool.
Assemble bearing stop (60) into quill (55).
Assemble spindle nut (62) to spindle and tighten securely.
Lubricate i.d. of piston cylinder (63) and o.d. of quill (55) with
ARO 36460 lube and assemble into outer sleeve (64). Handle
piston cylinder with care so as not to damage or distort the i.d.
Assemble locknut (68) to quill (55) and tighten securely.
Grease ‘‘O” rings (48 and 49) with ARO 36460 lube and as-
semble to grooves in frame assembly (35).
_
PULLEY SPINDLE SECTION ASSEMBLY
_
_
_
_
_
Assemble felt seal (24) to lock screw (25).
Assemble bearing (21) to ‘‘pulley” end of spindle (23), press-
ing on inner race of bearing.
Assemble spindle (23) and bearing into housing (10), press-
ing on outer race of bearing.
Assemble bearing spacer (22) and bearing (21) onto spindle,
pressing on inner race of bearing.
Assemble lock screw (25) to housing (10), securing spindle
and components.
Apply approximately 1/4 oz. (7 g) of ARO 33153 grease to in-
ternal splines of spindle (23) and assemble housing (10) and
components to frame assembly (35), securing with four cap
screws (20).
Refer to ‘‘BELT AND PULLEY SECTION” to complete the as-
sembly procedure.
_
_
_
_
_
_
_
Assemble outer sleeve assembly (64) and components to
frame assembly (35), assembling quill (55) thru yoke assem-
bly (27). Tighten outer sleeve securely. NOTE: Use caution
when inserting quill (55) thru frame assembly so as not to
damage wiper (26).
_
_
Tighten upper cap screw (28), securing yoke assembly.
_
VALVE HOUSING SECTION DISASSEMBLY
Control valves (37 and 39), manifold assembly (77) and con-
trol assembly (93) can be serviced without disrupting any oth-
er section of the tool.
Remove set screws (36 and 40), releasing control valves (37
and 39).
To service bushing assembly (45), pin (44), stem (43) or
spring (42), remove outer sleeve (64) and components as de-
scribed in ‘‘PISTON SECTION”.
Remove three cap screws (47), releasing magnet (46).
Remove bushing assembly (45), pin (44), stem (43) and
spring (42).
PISTON SECTION DISASSEMBLY
_
_
Loosen upper cap screw (28) on yoke assembly (27) to allow
for removal of quill (55).
_
_
Using a strap type wrench, unthread and remove outer sleeve
assembly (64) and components from the tool. NOTE: Remove
sleeve (64) with care. Pull sleeve straight away from the tool
so as not to bend the piston cylinder (63), damaging the inside
diameter.
Remove spindle nut (62) and locknut (68).
Remove spindle (58), bearing stop (60), bearings (59), spacer
_
_
_
_
(57) and bearing (56) from quill (55).
_
See pages 8 and 9 for disassembly and assembly of manifold
assembly (77) and control assembly (93).
_
Remove quill (55) and piston cylinder (63) from sleeve. NOTE:
Handle the piston cylinder carefully to prevent damaging or
distorting the inside diameter.
VALVE HOUSING SECTION ASSEMBLY
_
_
Remove piston cylinder (63) from quill (55).
Remove seal (50) and unthread and remove plate nut (51), re-
leasing plate (52) and spring washer (53).
_
_
Lubricate all ‘‘O” rings with ARO 36460 lube when assem-
bling.
Assemble control valves (37 and 39) to frame assembly (35),
securing with set screws (36 and 40). Set screws must be air
tight.
Assemble spring (42) to stem (43) and assemble into frame
assembly.
Assemble pin (44) into bushing assembly (45) and assemble
into frame assembly.
_
Do not remove wiper (26) from groove in frame assembly (35),
unless damage is evident. To remove wiper (26), refer to
‘‘Pulley Spindle Section” to separate drive housing (10) from
frame assembly (35).
Remove two cap screws (32), releasing stabilizer rod (31) and
yoke assembly (27) from tool. Wiper (26) can now be re-
moved.
_
_
_
_
Assemble magnet (46) to frame assembly (tangs on magnet
facing away from frame) and secure with three cap screws
(47). TIGHTEN TO 45–50 IN/LBS.
PISTON SECTION ASSEMBLY
_
_
Grease wiper (26) with ARO 36460 lube and assemble to
groove in frame assembly (35). NOTE: Assemble wiper with
lips towards ‘‘chuck” end of tool.
Assemble yoke assembly (27) to stabilizer rod (31) and as-
semble stabilizer rod to frame assembly (35), securing with
two cap screws (32).
_
Assemble outer sleeve (64) and components to tool as de-
scribed in ‘‘PISTON SECTION”.
4
M107
15
PART NUMBER FOR ORDERING
PART NUMBER FOR ORDERING
1
2
3
4
5
6
7
8
9
Button Head Screw (4 req’d) . . . . . . . . . . .
Drive Housing Cover . . . . . . . . . . . . . . . . .
Timing Belt . . . . . . . . . . . . . . . . . . . . . . . . . .
Cap Screw (2 req’d) (1/4” – 20 x 5/8”) . . .
Washer (2 req’d) . . . . . . . . . . . . . . . . . . . . .
Key (2 req’d) . . . . . . . . . . . . . . . . . . . . . . . .
Pulley (available only as a set, see chart)
Retaining Ring (.579” i.d.) . . . . . . . . . . . . .
Cap Screw (4 req’d) (1/4” – 20 x 3/4”) . . .
49688
49682
46923
Y99–458
46922
49673
49763–( )
Y145–22
Y99–41
49665
57 Bearing Spacer . . . . . . . . . . . . . . . . . . . . . .
58 Taper Spindle . . . . . . . . . . . . . . . . . . . . . . .
59 Bearing (2 req’d) . . . . . . . . . . . . . . . . . . . . .
60 Bearing Stop . . . . . . . . . . . . . . . . . . . . . . . .
61 Wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
62 Spindle Nut . . . . . . . . . . . . . . . . . . . . . . . . .
63 Piston Cylinder . . . . . . . . . . . . . . . . . . . . . .
64 Outer Sleeve Assembly . . . . . . . . . . . . . . .
67 Wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68 Locknut . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69 Frame Gasket . . . . . . . . . . . . . . . . . . . . . . .
70 Frame Plate . . . . . . . . . . . . . . . . . . . . . . . . .
71 Middle Gasket . . . . . . . . . . . . . . . . . . . . . . .
72 Middle Plate . . . . . . . . . . . . . . . . . . . . . . . . .
73 Manifold Gasket . . . . . . . . . . . . . . . . . . . . .
74 Valve Body Gasket . . . . . . . . . . . . . . . . . . .
75 Cap Screw (3 req’d) (#10 – 24 x 2”) . . . . .
76 Cap Screw (5 req’d) (#10 – 24 x 1–1/4”) .
77 Manifold Assembly (includes items 78
thru 92) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
78 Cap (2 req’d) . . . . . . . . . . . . . . . . . . . . . . . .
79 ‘‘O” Ring (2 req’d) (1/16” x 1/2” o.d.) . . . . .
80 Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
81 Rubber Ball . . . . . . . . . . . . . . . . . . . . . . . . .
82 ‘‘O” Ring (1/16” x 1/4” o.d.) . . . . . . . . . . . .
83 Actuator . . . . . . . . . . . . . . . . . . . . . . . . . . . .
84 ‘‘O” Ring (1/16” x 11/32” o.d.) . . . . . . . . . .
85 ‘‘O” Ring (1/16” x 9/32” o.d.) . . . . . . . . . . .
86 Needle Valve . . . . . . . . . . . . . . . . . . . . . . . .
87 Button Head Screw . . . . . . . . . . . . . . . . . . .
88 Retainer . . . . . . . . . . . . . . . . . . . . . . . . . . . .
89 Plug (5 req’d) . . . . . . . . . . . . . . . . . . . . . . . .
90 Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . .
91 Rubber Ball (2) . . . . . . . . . . . . . . . . . . . . . .
92 Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
93 Control Assembly (includes items 94 thru
112) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
94 Retaining Ring (2 req’d) (.859” i.d.) . . . . .
95 End Cap (2 req’d) . . . . . . . . . . . . . . . . . . . .
96 ‘‘O” Ring (2 req’d) (1/16” x 3/4” o.d.) . . . . .
97 ‘‘O” Ring (2 req’d) . . . . . . . . . . . . . . . . . . . .
98 Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
99 Face Plate . . . . . . . . . . . . . . . . . . . . . . . . . .
100 Control Valve (2 req’d) . . . . . . . . . . . . . . . .
101 Push Button (2 req’d) . . . . . . . . . . . . . . . . .
102 ‘‘O” Ring (2 req’d) (1/16” x 9/32” o.d.) . . . .
103 Needle Valve (2 req’d) . . . . . . . . . . . . . . . .
104 Breather Vent (2 req’d) . . . . . . . . . . . . . . . .
105 Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
106 Valve Body . . . . . . . . . . . . . . . . . . . . . . . . . .
107 Spring (2 req’d) . . . . . . . . . . . . . . . . . . . . . .
108 Rubber Ball (2 req’d) . . . . . . . . . . . . . . . . .
109 Seat (2 req’d) . . . . . . . . . . . . . . . . . . . . . . . .
110 Rubber Ball (2 req’d) . . . . . . . . . . . . . . . . .
111 Seat (2 req’d) . . . . . . . . . . . . . . . . . . . . . . . .
112 Button Head Screw (3 req’d) . . . . . . . . . . .
113 Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
114 Warning Label (2 req’d)(not shown) . . . . .
115 Date Code Plate (not shown) . . . . . . . . . .
116 Logo Plate (not shown) . . . . . . . . . . . . . . .
117 Tack (4 req’d)(not shown) . . . . . . . . . . . . .
118 Wrench (not shown) . . . . . . . . . . . . . . . . . .
49632
49631
49779
46973–1
47504
46975–1
49637
04596045
49635
46971
49679
49680
49681
49704
49776
49705
Y154-60-C
10 Drive Housing . . . . . . . . . . . . . . . . . . . . . . .
11 Electric Motor (.33 h.p., 230/460 V,
3 phase, 60 Hz)
3600 r.p.m. . . . . . . . . . . . . . . . . . . . . . . . . .
1800 r.p.m. . . . . . . . . . . . . . . . . . . . . . . . . .
49685–1
49685–2
49763–( )
Y99–41
Y145–7
49696
49695
49669
49670
49671
12 Pulley (available only as a set, see chart)
13 Cap Screw (1/4” – 20 x 3/4”) . . . . . . . . . . .
14 Retaining Ring (.225” i.d.) . . . . . . . . . . . . .
15 Spring Washer . . . . . . . . . . . . . . . . . . . . . . .
16 Ball Bearing (2 req’d) . . . . . . . . . . . . . . . . .
17 Tension Wheel . . . . . . . . . . . . . . . . . . . . . . .
18 Tension Wheel Pin . . . . . . . . . . . . . . . . . . .
19 Tensioner Bracket . . . . . . . . . . . . . . . . . . . .
Tensioner Assembly (includes items 14
thru 19) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 Cap Screw (4 req’d) (1/4” – 20 x 2–1/2”) .
21 Bearing (2 req’d) . . . . . . . . . . . . . . . . . . . . .
22 Bearing Spacer . . . . . . . . . . . . . . . . . . . . . .
23 Pulley Spindle . . . . . . . . . . . . . . . . . . . . . . .
24 Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 Lock Screw . . . . . . . . . . . . . . . . . . . . . . . . .
26 Wiper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27 Yoke Assembly (includes items 28, 29
and 30) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28 Cap Screw (2 req’d) (1/4” – 20 x 3/4”) . . .
29 Nut (1/4” – 20) . . . . . . . . . . . . . . . . . . . . . . .
30 Cap Screw (1/4” – 20 x 1”) . . . . . . . . . . . . .
31 Stabilizer Rod . . . . . . . . . . . . . . . . . . . . . . .
32 Cap Screw (2 req’d) (#10 – 24 x 3/4”) . . .
33 Yoke Guard . . . . . . . . . . . . . . . . . . . . . . . . .
34 Check Guard . . . . . . . . . . . . . . . . . . . . . . . .
Y154-57-C
49775
46696
Y325–12
40433
49847
Y325–6
49773
Y325–9
Y325–7
48441–1
49688
49788
59632–1
49678
44967
49774
49668
Y99–48
49780
49667
49643
44899
46931
49654
49662
Y99–41
Y12–4–C
Y6–45
49653
Y154-54-C
49674
Y147–77
116212
Y325–16
116485
116207–2
49677
49648
49676
Y325–7
48441–1
20311–1
49689
49675
48304–1
49784
49777
44967
49774
49688
04596037
49687
49686
35 Frame Assembly (includes items 36 thru 40) 49646
36 Set Screw . . . . . . . . . . . . . . . . . . . . . . . . . . .
37 Control Valve . . . . . . . . . . . . . . . . . . . . . . . .
38 Stop Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39 Control Valve . . . . . . . . . . . . . . . . . . . . . . . .
40 Set Screw . . . . . . . . . . . . . . . . . . . . . . . . . . .
41 Button Head Screw (5 req’d) . . . . . . . . . . .
42 Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43 Stem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44 Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45 Bushing Assembly (includes Y325–8
‘‘O” ring [1/16” x 5/16” o.d.]) . . . . . . . . . . .
46 Piston Stop . . . . . . . . . . . . . . . . . . . . . . . . .
47 Cap Screw (3 req’d) (#10 – 24 x 1/2”) . . .
48 ‘‘O” Ring (3/32” x 2–5/8” o.d.) . . . . . . . . . .
49 ‘‘O” Ring (1/16” x 2–1/2” o.d.) . . . . . . . . . .
50 Square Seal . . . . . . . . . . . . . . . . . . . . . . . . .
51 Plate Nut . . . . . . . . . . . . . . . . . . . . . . . . . . .
52 Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53 Spring Washer . . . . . . . . . . . . . . . . . . . . . . .
54 Wiper (2 req’d) . . . . . . . . . . . . . . . . . . . . . . .
55 Quill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56 Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49597
49648
49649
49648
49597
49688
49655
49661
49656
49658
49641
Y154-52-C
Y325-143
Y325–36
49642
49639
49638
49789
49633
49530
49683
49684
49791
49630
49780
30131–2
5
75
77
76
93
f 74
73
72
s
42
Q
45
44
43
71
70
69
37
36
Q
Q
5
4
52
L 47
46
Q
5
0
21
26
Q
25
41
51
40
24
29
30
28
Q
53
Q
4
9
Q
4
8
Q
3
9
35
38
31
32
33
27
34
68
67
Q
62
64
63
61
Q
60
59
6
M107
15
11
7
9
2
8
6
5
10
3
4
n
17
15
19
13
18
16
l
14
21
22
4
5
n
23
6
1
20
12
n ASSEMBLE WITH LOCTITE 290 AND TIGHTEN TO 50 – 60 IN. LBS.
l ASSEMBLE WITH LOCTITE 242.
s
I
N
C
L
U
D
E
D
I
N
4
9
5
9
5
S
E
R
V
I
C
E
K
I
T
.
Q INCLUDED IN 49594 SERVICE KIT.
f INCLUDED IN 49596 SERVICE KIT.
L TIGHTEN TO 45–50 IN/LBS.
58
56
55
57
#33 JACOBS TAPER
1/4–20 TH’D. x 3/4” LONG
7
49775 MANIFOLD ASSEMBLY
s
INCLUDED IN 49595 SERVICE KIT.
75*
* NOT INCLUDED IN ASSEMBLY
90
88
s
8
5
78
s
8
4
s
8
2
80
s
78
s
7
9
86
87
89
81
s
79
s
83
91
92
113
91
MANIFOLD DISASSEMBLY
MANIFOLD ASSEMBLY
_
_
Spring (80), ball (81) and needle valve (86) can be serviced
without removing the manifold from the tool.
Unthread and remove cap (78), releasing spring (80) and ball
(81).
Remove screw (87), releasing retainer (88).
Unthread and remove needle valve (86).
To further disassemble, remove three cap screws (75), releas-
ing manifold from the tool.
_
_
Lubricate all ‘‘O” rings with ARO 36460 lube when assem-
bling.
Assemble ‘‘O” rings (82 and 84) to actuator (83) and assemble
actuator into manifold, with the small diameter going into the
manifold first.
Assemble ‘‘O” rings (79) to caps (78) and assemble one cap to
manifold, securing actuator.
Assemble ball (81) and spring (80), securing with cap (78).
Assemble ‘‘O” ring (85) to groove in needle valve (86) and
thread needle valve into manifold.
_
_
_
_
_
_
_
Remove cap (78), releasing actuator (83).
_
_
Assemble retainer (88) to manifold, securing with screw (87).
Assemble manifold assembly to tool, securing with three cap
screws (75).
#3–56 MOUNTING HOLES
FOR OPTIONAL SOLE-
NOID VALVES.
#3–56 MOUNTING HOLES
FOR OPTIONAL SOLE-
NOID VALVES.
PORT ‘‘A”
DWELL
PORT ‘‘F”
PORT ‘‘E”
PORT ‘‘C”
PORT ‘‘D”
PORT ‘‘B”
#5–40 MOUNTING HOLES
FOR OPTIONAL 49785
PRESSURE SWITCH.
PORT ``A" INPUT / START (#10-32 THD.).
PORT ``B" INPUT / EMERGENCY RETRACT (#10-32 THD).
PORT ``C" OUTPUT / ``TOOL IS FORWARD" SIGNAL ``ON" AT FORWARD POINT OF PRESET STROKE (#10-32 THD).
PORT ``D" OUTPUT / ``TOOL IS RETRACTED" SIGNAL ``ON" WHEN TOOL IS FULLY RETRACTED (#10-32 THD).
PORT ``E" OUTPUT / AUX. AIR SUPPLY FURNISHES POWER AIR TO SOLENOID VALVE OPTION. SUPPLY IS ``ON" WHEN MAIN AIR INLET IS ``ON" (#10-32 THD).
PORT ``F" OUTPUT / AUX. AIR SUPPLY FURNISHES POWER AIR TO SOLENOID VALVE OPTION. SUPPLY IS ``ON" WHEN MAIN AIR INLET IS ``ON" (#10-32 THD).
DWELL
TIME CONTROL ADJUSTMENT KNOB ADJUSTS ``HESITATION" AT RETRACT POINT. TURN IN TO INCREASE TIME, TURN OUT TO DECREASE TIME.
8
M107
15
49674 CONTROL ASSEMBLY
76*
104
105
99
1/8–27 NPT
f 96
95
98
112
96 f
94
94
100
101
103
97 f
106
107
97 f
95
108
109
f INCLUDED IN 49596 SERVICE KIT.
* NOT INCLUDED IN ASSEMBLY
f 102
111
110
CONTROL DISASSEMBLY
_
Control valves (100) and needle valves (103) can be serviced
without removing the control assembly from the tool.
Remove three screws (112), releasing face plate (99).
Pull control valves (100) from valve body (106).
Unthread and remove needle valves (103).
To further disassemble, remove five cap screws (76), releas-
ing control assembly from the tool.
Remove retaining rings (94) and end caps (95) and push
spool (98) out of valve body (106).
_
_
Assemble ‘‘O” rings (96) to grooves in end caps (95).
Assemble one end cap (95) to valve body (106), securing with
retaining ring (94).
Assemble ‘‘O” rings (97) to grooves in spool (98) and as-
semble spool into valve body (106).
Assemble end cap (95) to valve body, securing with retaining
ring (94).
Assemble ‘‘O” rings (102) to grooves in needle valves (103)
and thread needle valves into valve body (106).
Grease ‘‘O” rings on control valves (100) and assemble into
valve body (106).
_
_
_
_
_
_
_
_
_
_
_
CONTROL ASSEMBLY
Assemble face plate (99) to valve body, securing with three
screws (112).
Assemble control assembly to tool, securing with five cap
screws (76).
_
Lubricate all ‘‘O” rings with ARO 36460 lube when assem-
bling.
FORWARD / START
PUSHBUTTON
EXHAUST, FEED CYLINDER
RETRACT / EMERGENCY
RETRACT PUSHBUTTON
RETRACT FEED RATE
MAIN AIR INLET (1/8–27 N.P.T.)
ADJUSTMENT KNOB
Q
FORWARD FEED RATE
ADJUSTMENT KNOB
Q
TURN ‘‘IN” TO DECREASE FEED RATE.
TURN ‘‘OUT” TO INCREASE FEED RATE.
Q
9
HYDRAULIC CHECK SET–UP
HYDRAULIC STROKE
CHECK
LENGTH
38922
38922–1
38922–2
1”
2”
3”
‘‘F” FEED CONTROL VALVE (103)
‘‘W”
‘‘Y”
‘‘X”
CAP SCREW (28)
HYDRAULIC CHECK
FEED RATE ADJUSTMENT
SET–UP PROCEDURE
•
•
Assemble hydraulic check to yoke assembly (27).
Measure the distance from the drill point to the work piece –
distance ‘‘Y”.
Distance ‘‘X” between the hydraulic check plunger and stop
pin (38) must be less than distance ‘‘Y” to prevent damage to
the drill point when it approaches the work piece.
Loosen cap screw (28) and position the hydraulic check to ob-
tain the correct setting for distance ‘‘X”.
Tighten cap screw (28) securely before operating unit.
Increase the air flow thru the feed control valve (103) marked
‘‘F” by opening two full turns from the closed position. This will
allow the drill to advance rapidly until the plunger of the hy-
draulic check contacts the stop pin (38).
The hydraulic check feed rate adjustment is located at the
nameplate end. Rotate the extended end until the slot at the
end of the spindle is aligned with the number 15 on the name
plate.
•
•
Start the drill unit and the drill will advance at a rapid rate until
the plunger of the hydraulic check contacts the stop pin (38).
Slowly rotate the extended spindle of the hydraulic check
counter–clockwise toward the number zero on the nameplate
until the drill advances at the desired rate of feed.
•
•
TO CONTROL BREAKTHROUGH
•
•
•
•
Position the hydraulic check so the distance between the
plunger and the stop pin (38)(distance ‘‘X”) is less than the dis-
tance from the drill point to the opposite side of the work piece
(distance ‘‘W”).
Set–up of the self–feed drill unit will be the same as explained
in ‘‘Set–Up Procedure”, page 3.
•
10
M107
15
ACCESSORIES
$.01
1.88
(48 mm)
49690 CLAMP ASSEMBLY
3 (76 mm)
9/32" DIA. THRU C'BORE 7/16"
DIA. x DEPTH SHOWN (4 HOLES)
$.01
2.25 (57 mm)
$.005
4.360
mm)
(111
$.0010
Y99-53 CAP SCREW (4 REQ'D)
2.9815 (76 mm)
49691 CLAMP
$.01
4.78 (121 mm)
$.005
2.750 (70 mm)
45060 KEY (4 REQ'D)
+.000
-.001
$.015
$.005
3/16 (5 mm)
Y194-95 SCREW (4 REQ'D)
.500 (13 mm)
1.500
(38 mm)
.218 (6 mm)
46982–1 MOUNT ASSEMBLY
$.005
3.000
(76 mm)
2.265
(58 mm)
$.010
3.750
(95 mm)
46979-1 MOUNT
$.005
Y99-678 CAP SCREW
4.750 (121 mm)
Y99-63 CAP SCREW (2 REQ'D)
5-9/16 (141 mm)
+.002
-.000
2.985 (76 mm)
4-7/8
(124 mm)
3-9/32
(83 mm)
$.001
2.750
(70 mm)
+.0015
+.005
-.000
-.0002
.5000 (13 mm)
$.010
.187 (5 mm)
1.875
(48 mm)
1/2 (13 mm)
#10 - 24 THREAD
11
CROSS SECTION
PN 49999–447
12
|