Refrigerator
Instructions for installation and use
IN E 160 G UK
Safety - a good habit to get into.
Never put ice cubes just removed from the freezer into your
ATTENTION
mouth because they could stick to your mouth and cause burns.
7. Never clean the appliance or perform maintenance without
first disconnecting it from the electrical mains. Turning the
Read your manual carefully since it contains instructions
which will ensure safe installation, use and maintenance of
your appliance.
Your Refrigerator is built to International safety standards
(EN60) ans has been awarded the European approval mark
(IMQ) for compliance with UK electrical safety requirements.
It also meets the EC standards on the prevention and elimi-
nation of readio interference (EC directive 87/308 - 02.06.89).
thermostat knob to the
setting does not suffice to break
all electrical contact with the mains.
8. Before having your old refrigerator picked up for disposal,
remove or make inoperable any locking devices to prevent
children who might play in or around the appliance from
being locked inside.
9. Before calling for service/assistance in the case of mal-
function, consult the chapter entitled “Is There a Problem?
to determine whether it is possible to eliminate the prob-
lem. do not try to repair the problem by trying to access the
internal components of the appliance.
10. If damaged, the power supply cord on this appliance
must necessarily be replaced by our service centre because
special tools are required for replacement.
11. Do not use electric appliances inside the compartment
for food storage, if these are not those recommended by
the manufacturer.
12. At the end of the functional life of your appliance –
containing cyclopentane gas in the insulation foam and
perhaps gas R600a (isobutane) in the refrigeration circuit –
the latter should made safe before being sent to the dump.
For this operation, please contact your dealer or the Local
Organisation in charge of waste disposal.
1. This appliance must not be installed outdoors - not even
in an area protected by a roof. It is extremely dangerous to
leave it exposed to rain or storms.
2. It must only be used by adults and exclusively to refriger-
ate and freeze foodstuffs, following the instructions for use
contained in this manual.
3. Do not ever touch or handle the appliance with bare feet
or with wet hands or feet.
4. It is highly recommended that you do not use extension
cords or multiple socket adapters. If the refrigerator is in-
stalled between cabinets, make sure that the cord is not
bent or dangerously pinched or compressed.
5. Never pull on the cord or the refrigerator to remove the
plug from the wall socket - this is very dangerous.
6. Never touch the cooling components within the appliance,
especially with wet hands because this could result in injury.
Installation
To ensure that the appliance operates properly and to
reduce energy consumption, it is important that the
appliance is installed correctly.
an earthing wire, the manufacturer will not be held liability
for any damages and or injuries arising out of the use of the
appliance. Do not use multiple sockets or adapters.
Position the appliance in such a w ay that you can access
the socket w here it is plugged in.
Ventilation
The compressor and condenser generate heat and, therefore,
need to be ventilated properly. Avoid placing refrigerator in
direct sunlight, or next to an electric stove or similar appliance.
Areas not adequately ventilated are not suitable for this
appliance.
Insufficient pow er?
The electrical socket must be able to handle the maximum
power load of the appliance, which is indicated on the rating
plate located at the bottom left next to the vegetable crisper.
During installation, make sure not to cover or obstruct the
grates that allow for proper ventilation of the appliance.
Before making the electrical connection ...
After the appliance has been delivered, place it in the verti-
cal upright position and wait at least 3 hours before insert-
ing the plug into the socket in order to ensure that it func-
tions properly.
Aw ay from Heat
Avoid positioning the appliance in a place where it is directly
exposed to sunlight or near an oven, cook top or the like.
Electrical Connection and Earthing
For English Market only
Before proceeding with the electrical connection, make sure
that the voltage indicated on the rating plate, located at the
bottom left near the vegetable crisper, corresponds to the
mains voltage in your home and that the socket is fitted
with a standard earthing wire in accordance with safety
standards for 46/90 systems. If the socket is not fitted with
The appliance is fitted with a continental 2-èin plug for factory
testing. Before installation the plug should be cut off. The ap-
pliance is designed to be installed in a switched spur outlet
fused at 13 Ampere. If the installation requires a 13 Ampere
plug type to be fitted it should be conform to BSI 1363.
GB
1
Important: the wires in the mains lead are coloured in
accordance with the following code:
Electrical connection
Your appliance is now supplied with a 13 amp fused plug that
can be plugged into a 13 amp socket for immediate use. Before
using the appliance please read the instructions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED
OUT BY A QUALIFIED ELECTRICIAN.
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
Replacing the fuse:
Connect Green & Yellow wire to terminal marked “E” or
When replacing a faulty fuse, a 13 amp ASTA approved fuse
to BS 1362 should always be used, and the fuse cover re-
fitted. If the fuse cover is lost, the plug must not be used
until a replacement is obtained.
or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked “L” or coloured Red.
Connect Blue wire to terminal marked “N” or coloured Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a 13
amp fuse. A 15 amp plug must be protected by a 15 amp
fuse, either in the plug or adaptor or at the distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the correct
colour as indicated by the coloured marking or the colour that
is embossed in words on the base of the plug. Replacements
can be obtained directly from your nearest Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with
the following code:
Removing the plug:
If your appliance has a non-rewireable moulded plug and
you should wish to remove it to add a cable extension or to
re-route the mains cable through partitions, units etc., please
ensure that either:
BLUE
BROWN
“NEUTRAL” (“N”)
“LIVE” (“L”)
GREEN AND YELLOW
“EARTH” (“E”)
- the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval
GREEN &ꢀ
YELLOW
or:
- the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which
is accessible without moving the appliance.
13 ampere fuse
BROWN
BLUE
CROSS-BARꢀ
CORD GRIP
Disposing of the plug:
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket. Instructions for connecting cable to an
alternative plug:
Disposing of the appliance:
When disposing of the appliance please remove the plug by
cutting the mains cable as close as possible to the plug body
and dispose of it as described above.
GB
2
A closer look
Temperature regulation knob
Container w ith Lid for Butter
D
B
A
(This container is not supplied with some models)
Use this knob to regulate the temperature of the
refrigerator. The following settings are available:
Door Shelf for Food Products
Door Shelf for Holding Bottles
Fruit and Vegetable Crisper
Drain for Defrost Water
C
D
E
F
refrigerator OFF;
1 minimum cold temperature;
5 maximum cold temperature
Removable, Height-adjustable Shelves
G
You can position the knob on any of the settings from
1 - 5 as required. Remember that you can turn off
your refrigerator by setting the knob to
.
A
B
C
C
G
F
D
E
GB
3
Setting up Your Appliance
ATTENTION
Before storing food in your refrigerator wipe the interior with
a solution of warm water and bicarbonate of soda.
After having plugged the appliance into the socket, make
sure that the refrigerator light has turned on. Then turn the
thermostat knob “A” to setting “3”. After a couple of hours,
you can place fresh food into the refrigerator.
After transport stand the appliance upright and w ait
at least 3 hours before plugging the appliance into the
mains to ensure proper performance.
Use these average temperature settings to ensure op-
timum performance and to save energy.
Fill the ice trays and place them in the compartment “H”.
Storage - getting the most out of your appliance.
Storing Food in the Refrigerator Compartment
Food
Storage Time
Location in the Refrigerator
Wrapped meat and cleaned fish
(use plastic wrap or pack in plastic bags)
On the shelf above the vegetable crisper
(which is the coldest area).
2 or 3 days
On the shelf above the vegetable crisper
(which is the coldest area).
Fresh cheese
Eggs
3 or 4 days
1 month
In special egg rack on door.
On any shelf.
Butter, margarine
Cooked or precooked food
(placer in air-tight containers and when cool store in 3 or 4 days
refrigerator)
On any shelf.
On any shelf.
Sausages, salami, sandwich meats in general, fresh
pasta, custards,puddings, chocolates, cream pastries, 3 or 4 days
bread, dry pastries, red tomatoes
Bottled products, milk, drinks, yoghurt
Fruits and legumes
On special door shelves.
In vegetable crisper.
What Not to Store in the Refrigerator
Garlic (transmits odour), onions and leeks.
Bananas (they will turn black).
Citrus fruits.
Potatoes and root vegetables (store in dark, dry places).
- Air in the refrigerator circulates naturally so that colder,
heavier air tends to descend towards the bottom. This is
why meat and fish should be stored just above the crisper.
- Remember to follow our instructions on the storage life of
foods: If not stored correctly, even the freshest food will
deteriorate quite quickly.
- Contrary to popular belief, cooked foods do not keep longer
than fresh food.
- Do not store liquids in unsealed containers since this will
increase the humidity and lead to the formation of frost in
the refrigerator.
GB
4
Energy Saving Tips
- Install the Appliance Correctly
This means that the appliance should be installed away from
heat sources or direct sunlight in a well ventilated room.
- Keep the Door Closed
Open the refrigerator only when necessary; remember that
every time you open the door most of the cold air will be
lost. To bring the temperature back to the proper level, the
motor must run for a considerable amount of time, con-
suming a substantial amount of energy.
THE ACTUAL ENERGY CONSUMPTION OF THE
APPLIANCE DEPENDS ON THE WAY THE SAME IS USED
AND ON ITS LOCATION. The consumption tests were
performed in 560mm deep column units, the most common
installation setting for this appliance.
- Check the Seal on the Door
Keep the seal clean and soft so that it fits tightly against the
door to ensure that no cold air is lost.
- Correct Temperature Settings
Set the refrigerator temperature knob to one of the middle
settings. Very cold temperature settings will not only con-
sume a great deal of energy but will neither improve nor
lengthen the storage life of the food. Excessively cold tem-
peratures may ruin vegetables, cold cuts and cheese.
- Never Put Food in the Refrigeror w hile Still
Hot
A container of hot food in the refrigerator will increase the
temperature significantly; allow food to cool to room tem-
perature before storing.
- Do Not Overfill Your Appliance
Remember that proper storage of food requires good air
circulation. Overfilling your appliance will hamper proper air
circulation and overwork the compressor.
GB
5
Caring for Your Appliance
Before doing any cleaning, disconnect the appliance
from the electricity (by pulling out the plug or turning
off the general sw itch in your home).
Cleaning and Maintenance
- Your appliance is manufactured with hygienic, odourless
materials. To preserve these characteristics, always use sealed
containers to store foods in order to prevent spills, stains
and the formation of difficult to remove odours.
- Only use a water and bicarbonate solution to clean the
applianc. Clean the internal and exterior of your appliance
with a sponge soaked in a warm water and sodium bicarbo-
nate solution, which is also a good disinfectant. If you do
not have any sodium bicarbonate at home, use a neutral
soap.
- What not to use: Do not use abrasive detergents, bleach
or detergents containing ammonia. Never use solvent based
products.
- All removable parts can be cleaned by soaking them in hot
soapy water or detergent. Remember to dry them thoroughly
before replacing them.
Defrosting
WARNING: do not damage the refrigeration circuit.
Do not use mechanical devices or other tools to speed
up the defrosting process, unless they have been rec-
ommended by the manufacturer.
The evaporator defrosts automatically during operation; the
defrost water drips into the drain, is collected in a special
tray and then evaporates.
Clean the defrost water drain hole periodically (see fig. 1) to
prevent water from collecting on the bottom of the refrig-
erator instead of flowing out.
- Discontinued use of the appliance: If the appliance is not in
use for any length of time, remember to clean the interior
and dry thoroughly, leaving the door open to prevent the
formation of odours and mould.
- Replacing the light bulb. The bulb for lighting the interior
of the appliance is located at the back of the thermostat
box. Unscrew the burned out bulb and replace it with an-
other bulb with a wattage no higher than 15 Watt, follow
the instructions illustrated in fig. 2.
Fig. 1
Before carrying out this operation, disconnect the appli-
ance from the electricity (to do so, turn off the general switch
in the house or remove the plug for the appliance from the
socket).
.
Fig. 2
GB
6
Trouble Shooting
The Refrigerator does not Work
Check that:
• The mains switch in your home is on.
If after all the checks, the appliance still does not operate or
the problem persists, call the nearest Service Centre and
inform them of: the type of problem, the abbreviation of
the model name (Mod.) and the relative numbers (S/N) writ-
ten on the rating plate located at the bottom left next to
the vegetable crisper (see example in the figure below).
The Appliance does not Refrigerate Properly
Check that:
• The door is shut properly and that the door seal is not
damaged;
• The thermostat temperature knob is on the correct setting;
• The refrigerator has not been overfilled.
TI
93139180000
Cod.
S/N 704211801
RG 2330
Mod.
Fuse
A
Max 15 w
220 - 240 V-
50 Hz 150 W
W
Food in the Refrigerator is too Cold
Check that:
• The thermostat knob is on the correct setting.
Class
Freez. Capac
Poder de Cong Clase
340
75
Total
Net
Gross
Bruto
Brut
Gross
Bruto
Brut
Gross
Bruto
Brut
N
Util
Utile
Classe
kg/24 h 4,0
Pressure
HIGH-235
LOW 140
Compr.
Syst.
Kompr.
Test
R 134 a
The Motor Runs Continuously
Check whether:
P.S-I.
kg 0,090
Made in Italy 13918
• The door is not closed properly or has been left open;
• The room temperature is not too high.
Never call on unauthorized technicians and alw ays
refuse spare parts w hich are not originals.
The Appliance is Noisy
Check whether:
• The appliance is perfectly level;
• The appliance has been installed between cabinets or other
objects that vibrate or make noise.
There is Water on the Bottom of the Refrigerator
Check whether:
• The defrost drain is clogged.
Remember that the refrigerant in the cooling circuit causes
a slight bubbling sound, even when the compressor is not
running (this is quite normal).
GB
7
GB
8
Merloni Elettrodomestici
Viale Aristide Merloni 47
60044 Fabriano
Italy
Tel +39 0732 6611
Fax +39 0732 662501
|