InFocus Projector Setup Guide for an HDTV receiver
How to connect an HDTV receiver to an InFocus projector
Analog Video Out
Audio Out
Digital Video Out
HDMI
Surround Sound
Stereo
Composite S-video
Component
Cable In
DVI
Digital
Optical
Digital
Coax
L
Y
Pb/Cb Pr/Cr
R
To TV/VCR
Composite
Component
Y
VGA
RS-232
S-video
Pb
Pr
L
M1-DA
R
Table of Contents
- For the quickest setup using a component video cable, see pages 2-3.
Best
Premium
- If you have a DVI port on your HDTV receiver and a M1 port on your projector, see page 4.
Premium
- If you have a HDMI port on your HDTV receiver and a M1 port on your projector, see page 5.
For more information and troubleshooting...
Read the tips, common issues and frequently asked questions on pages 6-8.
Connect an HDTV receiver to a projector (w/o component) using a component video cable
Setup Requirements
HDTV receiver with component video-out ports
Projector without component video-in ports
M1 to component adapter (InFocus part #SP-M1-ADPT)
Component video cable (red, green, blue male RCA)
HDTV Receiver Connector Panel
connector panel may vary from actual product
Analog Video Out
Audio Out
Digital Video Out
Analog Video Out
Composite
Audio Out
HDMI
Digital Video Out
Surround Sound
Stereo
Composite S-video
Component
Cable In
1
DVI
Digital
Optical
Digital
Coax
L
R
Y
Pb/Cb Pr/Cr
To TV/VCR
HDMI
Surround Sound
Stereo
S-video
Component
Cable In
DVI
Digital
Optical
Digital
Coax
L
Y
Pb/Cb Pr/Cr
R
Plug the component video
cable into the component
ports on the HDTV receiver.
To TV/VCR
Connect to surround
sound receiver to
Connect to external audio
receiver, speakers or
component video connectors
receive surround sound
projector (if supported).
*
2
Composite
Video
VGA
RS-232
S-video
L
M1-DA
R
Projector Connector Panel
Connect the other end of the
cable to the M1 to component
Composite
adapter. Connect M1 adapter
to the M1-A port on the projector.
Video
L
VGA
RS-232
S-video
component video cable
(3rd party optional accessory)
M1-DA
R
3
connector panel may vary from actual product
S
TA
NDBY
Power on the projector, then the
HDTV receiver. You are ready to
watch high definition television!
We recommend connecting the HDTV receiver to an external
sound system to provide the best audio experience.
M1 to component adapter
(optional accessory)
*
3
Connect an HDTV receiver to a projector using a DVI (digital video interface) cable
Setup Requirements
HDTV receiver with DVI-out port
Projector with M1-D port and HDCP support
M1 to DVI cable (6 ft, InFocus part #SP-DVI-D or 33 ft, InFocus part #SP-M1-10M)
HDTV Receiver Connector Panel
connector panel may vary from actual product
Analog Video Out
Audio Out
Analog Video Out
Composite
Digital Video Out
Audio Out
Digital Video Out
HDMI
Surround Sound
Stereo
Composite S-video
Component
Cable In
1
DVI
Digital
Optical
Digital
Coax
L
R
Y
Pb/Cb Pr/Cr
HDMI
To TV/VCR
Surround Sound
Stereo
S-video
Component
Cable In
DVI
Digital
Optical
Digital
Coax
L
Y
Pb/Cb Pr/Cr
R
Plug the DVI connector into
the DVI-out port on the
DVD player.
To TV/VCR
Do not connect
Connect to surround
sound receiver to
Connect to external audio
receiver, speakers or
receive surround sound
projector (if supported).
*
2
Component Composite
Y
RS-232
DVI-D
connector
VGA
Pb
L
Pr
M1-DA
S-video
R
USB connector
Projector Connector Panel
Composite
Connect the M1-D connector
to the M1 port on the projector.
Video
L
VGA
RS-232
S-video
M1 to DVI-D cable (6 ft)
(optional accessory)
M1-DA
R
3
connector panel may vary from actual product
S
TA
NDBY
M!-D
connector
Power on the projector, then the
HDTV receiver. You are ready to
watch high definition television!
We recommend connecting the HDTV receiver to an external
sound system to provide the best audio experience.
*
4
Connect an HDTV receiver to a projector using an HDMI (high definition multimedia interface) cable
Setup Requirements
HDTV receiver with HDMI-out port
Projector with M1 port and HDCP support
M1 to HDMI adapter (2 in, InFocus part #SP-HDMI-ADPT)
HDMI cable (3rd party)
HDTV Receiver Connector Panel
connector panel may vary from actual product
Analog Video Out
Audio Out
Digital Video Out
Analog Video Out
Composite
Audio Out
Digital Video Out
HDMI
Surround Sound
Stereo
Composite S-video
Component
Cable In
1
DVI
Digital
Optical
Digital
Coax
L
R
Y
Pb/Cb Pr/Cr
HDMI
To TV/VCR
Surround Sound
Stereo
S-video
Component
Cable In
DVI
Digital
Optical
Digital
Coax
L
Y
Pb/Cb Pr/Cr
R
Plug the HDMI connector
into the HDMI port on the
HDTV receiver.
To TV/VCR
Connect to external audio
receiver, speakers or
Connect to surround
sound receiver to
projector (if supported).
receive surround sound
*
HDMI
connector
Connect coax cable to
Cable In on HDTV receiver.
2
Component Composite
Y
RS-232
VGA
Pb
L
Pr
M1-DA
S-video
R
Projector Connector Panel
Composite
Video
Connect the HDMI connector
to the M1 to HDMI adapter
on the projector.
VGA
RS-232
S-video
HDMI cable
(optional accessory)
L
M1-DA
R
3
connector panel may vary from actual product
S
TA
NDBY
M1 to HDMI adapter
(optional accessory)
Power on the projector, then the
HDTV receiver. You are ready to
watch high definition television!
We recommend connecting the HDTV receiver to an external
sound system to provide the best audio experience.
*
5
Tips
•
•
•
•
For the best sound, we recommend connecting the HDTV receiver to an audio receiver or a surround sound system. Only optical and coaxial audio
cables support 5.1 surround sound. With red and white RCA audio cables, you only receive 2.1 stereo sound.
If you are connecting your HDTV receiver to the M1 port, you need a special adapter. Refer to the Service and Support web site or the InFocus
user guide to reference the video connectivity charts.
DVI will provide the best signal. Current HDTV receivers have DVI and component connectors. Older HDTV receivers may only have component
video. Composite and S-video cables cannot transmit a high definition signal.
Check your HDTV receiver’s aspect ratio, output type and 4:3 override settings in the menu.
o
o
o
Aspect ratio will control how the HDTV receiver will display the signal. Make sure the aspect ratio of the HDTV receiver matches the
standard aspect ratio of your projector. This will maintain the proportion of your video image.
Output type is the preferred video format for high definition television stations. There are two choices: 720p or 1080i.
720p is recommended for the best video quality.
4:3 override is the video format for standard programming. There are two choices: 480i or 480p.
480p is recommended for the best video quality.
•
•
When sending video through DVI, ensure that your projector is HDCP compatible. All InFocus ScreenPlay models with M1 ports are HDCP
compatible. Most business projectors are not compatible. Consult the Service and Support web site or user guide.
We recommend DVI cables to not exceed 33 feet. When purchasing third party cables, always look at their rating. Cables may have ratings of a
shorter distance based on the signal format that you are using. Higher resolution formats will have shorter distance ratings. (i.e. a cable may be
rated for 33 feet for 720p, but may be rated only 15 feet for 1080p signal.)
•
•
All TV stations are not broadcast in high definition (720p or 1080i). Commercials and some channels will be displayed in 480i or 480p. Check with
your cable provider to verify which channels are displayed in high definition.
connectivity information.
6
Common Issues
SYMPTOMS: Image is not perfectly rectangular (keystoning)
SYMPTOMS: Light bar rolling from bottom to top
Solution: When a projected image is wider at the top or the bottom
(horizontal keystoning), or taller on the right or left side (vertical
keystoning), the projector is not perpendicular to the screen, either in
the vertical plane or the horizontal plane.
Solution: This is probably a ground loop issue. Ground loop effects
are caused by a differential in the power between the source and
projector. The solution is to ground the source and projector. Use a
ground loop isolator and/or plug both the source and projector to the
same power outlet.
If the sides are angled, then you need to raise or lower the front of the
projector. Also, most projectors have digital vertical keystone
correction that you can adjust in the projector menu. If the top and
bottom of the image are angled, then you need to rotate the projector
left or right until the image is rectangular. Most projectors do not have
digital horizontal keystone correction.
A rolling bar can also be caused by poorly shielded cabling. Make sure
you use quality cables
SYMPTOMS: Static, noise, or video artifacts in video image
Solution: Usually you can eliminate a lot of video defects by using
high quality cable in as short a length as possible. For the best results,
we recommend using DVI or component cables with the projector.
Composite and S-video cables do not support high definition and
produce lower quality video. Try to keep cable length to less than 10
feet. If the setup requires a longer cable, make sure to use the thicker,
well-shielded cables.
SYMPTOMS: Image proportion is incorrect
(i.e. people appear too tall or too short)
Solution: The aspect ratio is set incorrectly on the projector and/or the
HDTV receiver. Make sure the projector and HDTV receiver aspect
ratio are the same. In the projector menu, you can adjust the aspect
ratio. In the HDTV receiver menu, you can adjust the aspect ratio.
SYMPTOMS: No video image from the projector
Solution:
SYMPTOMS: Sound is too soft from projector speakers
Solution: We recommend connecting the HDTV receiver to a home
theater audio receiver or amplifier to receive a more robust and quality
audio experience. The speakers on the projector are meant for very
small spaces.
•
Check the coaxial cable connection to the HDTV box.
Typically, there are two coax connections on an HDTV
receiver: To TV and Cable In. Make sure the cable is securely
connected to the Cable In port.
•
Make sure the projector is searching the correct input (see the
projector user’s guide). If Auto Source is turned off, you need
to manually change the source that the projector is searching.
Press the Auto Source or Video button the projector keypad or
remote.
•
•
Try a different video cable. The cable may be defective.
Some video ports do not accept progressive signals. Refer to
connectivity chart on the Service and Support web site.
7
Frequently Asked Questions
Where is the luma detail, chroma detail, CCS and noise reduction
settings in the advanced menu? My advanced menu is not
matching what I see in the user guide.
Which one is better: 480i (480 lines interlaced) or
480p (480 lines progressive)?
Most people cannot tell the difference between 480i and 480p.It
depends on whether the projector or the source has the better
deinterlacer chip. When you send 480i to the projector, the projector’s
deinterlacer converts the signal to a progressive signal. When you
send 480p, the video source’s deinterlacer converts the signal. We
recommend sending 480i to the projector.
These range of advanced options varies, depending on which video
source is active. The ones listed above are available only when
composite, s-video or 480i component signals are projected. If you are
sending digital, 480p, 720p or 1080i signals, these options are not
available.
At what cable length do I lose video quality?
Which cable provides me with the best video quality?
The answer depends on the quality of cabling you use. Some cables
begin to lose noticeable quality beyond 10 feet. Higher quality cables
can maintain a clean signal beyond 25 feet. To guarantee the best
video quality, we recommend using heavy duty shielded cabling (for
example Monster Cable or Belkin). Use as short a cable as your setup
allows.
Connector Type
Composite
Quality
Good
Signal Type
Analog, standard
definition
Analog, standard
definition
Analog, 480i, 480p,
720p, 1080i
Digital, 480p, 720p,
1080i, 1080p
Digital, 480p, 720p,
S-video
Better
Best
Component
When is the projector’s deinterlacer used?
DVI
(digital video interface)
HDMI
Premium
The projector’s deinterlacer is used when you send an interlaced signal
to the projector. If you send composite, S-video or 480i component
video to the projector, the deinterlacer is used. If you send progressive,
the source device’s deinterlacer would be used.
(high definition multimedia Premium 1080i, 1080p, up to 8
interface)
channel audio
What does Overscan do?
Some video devices cause noise around the edges of an image.
Overscan crops approximately 3% of the image to hide this video
noise. The disadvantage of this feature is that you lose part of the
image. Most InFocus projectors include this option in the menu when a
standard definition or interlaced signal is projected. You can turn
Overscan off through the projector menu or, with some projectors, with
the remote control.
8
|