Installation Guide
Installation
eSATA 3Gbps Dual ports Express Card/34 Host
GPS702e3W6
PART NO. M0554
Table of Contents
Introduction
4
Features
5
Package Contents
6
Software Installation
7
Federal Communications Commission (FCC) Statement
10
12
13
14
CE Statement
Limited Warranty
Contact
3
Introduction
The ExpressCard Host allows you to upgrade your Notebook computer with up to two SATA II
Channels. The board provides a 2.5Gbps ExpressCard interface on the host side, and dual fully
compliant SATA II 3Gbps ports on the device side to access Serial ATA mobile external and internal
storage devices such as: hard drives, ZIP drives, CD-ROMs, CD-RWs and DVD-ROM drives.
4
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
External SATA II (eSATA) Connector
48 bits LBA can Break Capacity-Limit to Support HDD larger than 137GB
Supports 1-lane 2.5Gbps ExpressCard/34
Hot-plug capability
Supports SATA II transfer rate of 3.0Gbps
Fully compliant with Serial ATA 1.0 specifications
Supports two independent Serial ATA channels
Independent Link, Transport, and data FIFO
Independent command fetch, scatter/gather, and command execution
Supports Legacy Command Queuing (LCQ)
Supports Native Command Queuing (NCQ)
Supports Non-zero offsets NCQ
Supports Out of order data delivery NCQ
Supports FIS-based switching with Port Multipliers
31 Commands and Scatter/Gather Tables per Port
Two LEDs indicate for HDD access
Completely with drivers for Windows NT, Windows 2000, Windows XP, Windows Vista and Windows
Server 2003
5
Package Contents
•
•
•
SATA ExpressCard Host Adapter
Quick Start Guide
Driver CD
6
Software Installation
Windows XP Installation
1. Insert the SATA Card into an available slot.
Connect the serial ATA cable(s) between the
SATA port and serial ATA device(s).
2. Windows will display the ‘Found New
Hardware Wizard’. A new ‘Mass Storage
controller’ will become detected.
3. Insert the Driver CD into your CD-ROM/DVD
Drive.
4. Select “Install from a list or specific
location (Advanced)”, and click “Next”.
7
5. Select “Search for the best driver in these
locations”, and check “Include this location
in the search:” Be sure to uncheck the other
available boxes.
6. Type the appreciate media drive letter and
select the “Browse” option.
7. Specify a location [CD Drive Let-
ter]:\SATA Express_2Port \Sil3132 \
WinXP_2000_2003_NT, and click OPEN then
select OK.
8. When the wizard indicates that it found a driver
for the device click ‘Next’.
9. The wizard will now copy the required files to
the system and initialize the Driver. After starting
the driver the wizard will display a completion
dialog, click ‘Finish’ to exit the wizard.
8
Verify Windows XP Installation
1. Right click on the ‘My Computer’ icon, select
‘Properties’, left click on the ‘Hardware’ tab,
and select the ‘Device Manager’ button.
2. Double click on ‘SCSI and RAID Controllers’,
If there is no yellow ‘! ‘ or ‘ ? ‘ in front of
‘Silicon Image SiI 3132 SATALink Controller’,
the driver is functioning properly.
9
Federal Communications Commission (FCC) Statement
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
10
-
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
1. this device may not cause interference and
2. this device must accept any interference, including interference that may cause undesired operation of
the device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End
users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.
11
CE Statement
CE Statement
This device has been tested and found to comply with the requirements set up in the council directive on
the approximation of the law of member states relating to EMC Directive 89/336/EEC, Low Voltage Directive
73/23/EEC and R&TTE Directive 99/5/EC.
12
Limited Warranty
The manufacturer, IOGEAR, makes NO warranty or representation, whether express or implied, regarding
the contents, use or suitability of this software, disk or documentation. IOGEAR specifically disclaims any
and all warranties regarding the quality and performance of this software, disk or documentation including,
but not limited to the implied warranty of merchantability and implied warranty of fitness for a particular
purpose. IOGEAR shall not be responsible or liable for property damage, loss of use, interruption of
business, lost profits, lost data or other consequential, punitive or special damages, however caused and
however alleged.
IOGEAR reserves the right to revise or update the software, disk or documentation without advance
notification of such revision or update. For additional information please contact IOGEAR at:
Email – support@iogear.com, Telephone - 949-453-8782 or toll free 866-9-IOGEAR, or
Fax - 949-453-8785.
13
Contact
Toll Free: (866) 9-IOGEAR
Phone: (949) 453-8782
23 Hubble
Irvine, CA 92618 USA
support@iogear.com
14
15
About Us
FUN
IOGEAR offers connectivity solutions that are innovative, fun, and stylish,
helping people enjoy daily life using our high technology products.
GREEN
IOGEAR is an environmentally conscious company that emphasizes the
importance of conserving natural resources. The use of our technology solutions
helps reduce electronic waste.
HEALTH
IOGEAR supports healthy and fit lifestyles. By integrating products with
the latest scientific developments, IOGEAR’s solutions enhance the life of
end-users.
© 2007 IOGEAR, INC.
|